Search Documents

By M. Townsend, E. L. Petsonk, B. Fedders, M. Niggemeyer, H. Abrons, E. Daniloff, J. Griffin, K. Kinsley

In certain populations, nonspecific airway hyperreactivity (HR) is associated with increased respiratory symptoms and decreased lung function. We analyzed standardized pulmonary symptom questionnaires and pre-shift spirometry with methacholine inhalation challenge (Chatham, M. et al, Chest 82: 15) on 228 control workers (C) with no known exposure to occupational hazards, and 200 underground bituminous coal miners (M). M and c were similar in age, height, sex, and smoking status. HR (defined as >15% fall in FEVI after up to 5 vital capacity breaths of 25mg% methacholine) was found in 25% of M and 28% of C (NS). M showed higher% predicted FEVI (%PFEV) than c (M 107%, C 104%*). 28% of current smokers showed HR versus 22% of never smokers (NS). Current smokers showed reduced %PFEV but were not different from lifelong non-smokers regarding prevalence of HR. Subjects with HR showed reduced %PFEV, (HR 101%, not HR 107%*) but M and c with HR showed similar reductions. M had more dyspnea and chronic cough than c*. Hyperreactivity was associated with increased symptoms in controls but not miners. In our study, the prevalence of HR in coal miners was similar to nonminers, and did not explain miners' respiratory symptoms. * P < 0.05

Jan 1, 1989

By W. E. Wallace, P. Bolsaltis, M. J. Keane, B. L. Rauaboni

Thermal treatment of respirable size silica dust samples results in marked changes in their hemolytic activity. These changes can be correlated with changes in the characteristics of the particle surface as measured by infrared spectra, zeta potentials, and specific surface area. Silica samples from various sources (Min-U-Sil, fumed silica, and a NIOSH standard sample) were heated or calcined at temperatures ranging from 100-1095C. The hemolytic activity of the crystalline materials decreased after thermal treatment. The behavior of the fumed material was found to be more complex. Material of very large surface area (small particle size) exhibits an initial increase in hemolytic activity upon calcination. This result confirms other experimental observations pointing to a particle size of maximum toxicity. Tre changes in hemolytic activity can be related to infrared spectra and zeta potentials of the materials. The absorption band in the 3200-4000 cm-1 frequency region of the fumed material disappears upon heat treatment while a sharp, characteristic band at 3750 cm-1 increases in intensity. Zeta potential measurements conducted in the pH range of 2.0-10.5 exhibit a unique change in zeta potential v.s. pH profile with heat treatment. These findings indicate that the removal of active surface silanol groups by calcination results in reduced cytotoxicity, as measured by a hemolysis test.

Jan 1, 1988

By A. A. Afshari, D. G. Frazer, C. F. Stanley

"INTRODUCTIONThe primary function of the lung, i.e. gas exchange, occurs in peripheral units termed alveoli• Diagnosis of lung dysfunction ls therefore dependent on techniques to evaluate the status of the peripheral airways. Since these airways and alveoli are very small, it is difficult to determine directly how they function or how the function is changing due to disease. Yet this unde1·standing is critical to the design of instrumentation to detect early changes in lung function due to disease.An interesting hypothesis describing one aspect of small airway function has been proposed by Frazer (1) as gas trapping due to the formation of menisci in the airways. An additional study (2) proposes that the breaking and possibly the formation of these menisci could generate lung sounds, i.e. crackles. These lung sounds were recorded by placing a microphone at the trachea of an excised rat lung. The lung was degassed and then inflated and deflated. At points along the path of inflation, lung sounds were recorded. However, determination of the origin of the sounds was not attempted due to the difficulties induced by contacting the lung st1rface with a microphone.The purpose of this paper is to describe a non-contacting, whole field technique to monitor and describe the movements of the lung surface during inflation - deflation cycles.HOLOGRAPHIC INTERFEROMETRYHolographic interferometry is a full field, non-contacting and non-destructive technique that measures deformations of an object with a sensitivity in the order of the wavelength of light. A laser beam is split, with one beam reflected from an object and the other used as a reference beam. Both beams combine to produce a hologram of the object on a photographic plate. The process utilizes the concepts of interference, i.e. the two wave amplitudes will add at the points where the difference in optical path lengths over the exposure period is zero or a whole number of wavelengths and will subtract at other points."

Jan 1, 1989

The Bureau of Mines believes that all coal mines are potentially gassy; for the purpose of administration in the prevention of explosions and fires, the Bureau recommends: That any coal mine wherein methane or other combustible gas can be detected in amounts as much as 0.27 of 1 percent or more by frequent systematic searches shall be classified as a gassy mine. Permissible methane-indicating detectors such as are given in I.C. 7110 or subsequent lists of Bureau approved methane-indicating detectors, or conventional methods of sampling and analysis of required accuracy may be used. The concentration referred to in the decision is percent by volume.

Jan 1, 1941

By R. R. Sayers

The terms "sanitation and }\Vgienen are often used interchangeably, but it is more "' usual to apply ttsani tat ion'' to th environment or surroundings, and nr.ygieneto the iiiividual, The subject,. h9wever, is so broad that only a few of the phases of sanitation will be di.acusae in ·this paper, vmile the various Fsea of hyg:tene will be deferred for later consideration. One of the bes.t .iaf ini tions of sanitation that I have hearci was given by ur. L. L • Lumsden, of the U, S. Public Heal th Service, who state.d that "'sanitation is t-he c.oir .. 'Don-sens$ application of the principles of cleanliness,

Aug 1, 1922

By Ronald S. Conti

Fire is a major concern for those who work in underground mines. A mine fire can occur at anytime and often results in a partial or total evacuation of mine personnel and could result in the loss of lives. Therefore, having a workforce that is well trained to prevent, detect, and fight a fire is important. This paper focuses on responders’ preparedness for fire. Responders in this context are considered the entire workforce and are categorized as first, second, and sustained responders and evacuating miners. Quality training enhances ones awareness of mine fire hazards and promotes self-confidence in combating fires and responding to emergencies. Early warning systems and other escapeway aids such as a through-the-earth signaling and communication system, lasers and strobe lights are also addressed. The technological advancements that have been made can improve the state-of-preparedness for responders to underground emergencies and increase the chances of survival for escaping personnel.

By E. J. Gleim

In the movement of self-controlled direct-current machinery, particularly shortwall cutting, machines, from one place to another in coal mires, "nipping" or it stinging" has been practiced quite commonly. These terms refer to the method of obtaining current for propelling or tramming the machines along trolley haulageways by sliding the trolley trip (hook or nip), which terminates one conductor of the trailing cable, along the trolley wire. This is usually done by the machine operator or runner while sitting on the machine truck and holding the nip terminal against the trolley wire as the machine travels along the rails. This procedure is objectionable for several reasons. Under the best conditions, the area of contact between the nip and trolley wire is snail end, consequently, sparking and flashing ore most likely to be continuous as the machine proceeds. This is undesirable, not only because of the detrimental effect of electric flashes upon eyesight, but because of the pitting and roughening the trolley wheels which decrease the efficiency of current collection by locomotive trolley wheels and shoes and at the same time shorten their useful life by increased wear.

Jan 1, 1939

By S. P. Howell

The Bureau of lines as repeatedly called attention to dangerous practices in the transportation and opening of kogs of black blasting powder. In 1914 Diwin Higgins (Prevention of Accidents from Explosives in Metal inos, Miners' Circular 19, Bureau of Mines, p. 15) stated "canisters should always be opened by removing the bung. To use a pick or other sharp tool for cutting a hole in the canister is dangerous. After the necessary amount of powder has boon taken out, the canister should be kept closed. The powdor should always be handled at a safe distance from an open light." In 1919, Geo. S. Rice (onthly Statement of Coal line Fatalities for June, 1919, Bureau of Mines, pp. 16 to 18) calls attention to the dangers that arise in underground transportation and handling of explosives, and calls special attmtion to the danger of hauling explosives in motor trips; the unnecessary risk involved in hauling men on the trip at the same time, and the necessity of keeping open lights away from black blasting powder. In 1919 the writer (Sensitiveness of Explosives to Frictional Impact, Tech. Paper 234, Bureau of Mines, pp. 13, 15) called attention to the fact that black blasting powder is not as sensitive to frictional impact as the nitro-glycerin dynamites and the gelatin dynamites. Black powder may be ignited by direct impact and the writer believes that this may occur without presupposing a preliminary spark. It is well known, however, that black blasting powder is very sensitive to ignition by spark flame, or heated materials, and these may be produced by an electric current, by an open light, by incandescent particles from a pipe, cigar, or cigarette, by the tearing of metal sheets or scraping of metal against metal, and possibly, by other means. -- The above discussion will serve to introduce a newly recognized hazard the ignition of black blasting powder by the forcible opening of kegs with wodden tools. The details of three accidents in which kegs of black blasting powder ex- ploded instantly when a wooden tool was driven forcibly through the top of the kegs are as follows: 1. In 1915, a powder man employed by a coal mining company stated that he was opening a 25-pound log of black blasting powder by driving a hole in the top with a wooden sprag when the powder in the leg ho was opening ignitod. This caused the ignition of fifty-two additional 25-pound logs of the powder, and the fatal burning of this and another powder man. The ono making this statement lived five hours after the explosion.

Sep 1, 1920

By Lawrence Y. Marks

During the mineral survey of the Bob Marshall Wilderness and study areas by the author in 1971, 1973, 1974, and 1976 (Marks, 1978), the area designated Reservoir-North (RARE II No. H1-485) in January, 1979, (U.S. Forest Service, 1979) was examined, along with other lands adjacent to the earlier study areas. However, the 1978 open-file report covered only areas originally designated for study. The present report on Reservoir-North is based on earlier work. No work has been done in the area since 1976. Mineral Appraisal Reservoir-North RARE II area (No. H1-485) is in the Northern Disturbed Belt which has been identified as having high potential for natural gas accumulations and lesser potential for oil accumulations (Mudge, 1978). Oil and gas lease applications in the area, indicate interest by oil companies.

Jan 1, 1981

By Dennis Dolinar, Christopher Mark, Gregory M. Molinda

In 1999, 2,087 unplanned roof falls were reported from 841 mines. Nearly 55% of all mines reported at least one roof fall, and nearly 17% of the mines reported five or more falls. In order to investigate the variables that contribute to roof falls, the National Institute for Occupational Safety and Health (NIOSH) compiled a national database of roof performance from 37 coal mines. Geotechnical factors and their effect on roof fall rates were compiled from over 1,500 miles of drivage. The factor that is the best predictor of roof fall rate is the Coal Mine Roof Rating (CMRR). For a low CMRR (#30), almost all cases have high roof fall rates. Conversely, high roof fall rates are rare for strong roof rocks (CMRR $ 60). Roof fall rates were also higher in deeper mines, probably because of greater stresses. Intersections were much more likely to fall than roadways, and four-way intersections were more prone to fall than three-way intersections. In a controlled comparison of the effect of increasing bolt length on roof fall rates, it was found that longer bolts reduced the roof fall rates in 11 of 13 cases. A relationship between the roof fall rate, the intersection span, and the CMRR was also found. Finally, a systematic method for tracking roof performance and geotechnical variables was demonstrated.

Jan 10, 2000

By Forrest T. Moyer

THIS CHAPTER of the Minerals Yearbook contains injury experience and related employment information for the coal-mining, coking, oil and gas, peat, and native asphalt industries in the United States for 1962. Injury experience is measured by the number of injuries sustained per million man-hours of exposure in each industry. No attempt has been made to combine these data and present rates reflecting the mineral-fuel industries because the hazards of the separate industries are not comparable. Tabulations showing the trend of injuries and employment for all mineral industries are presented in volume III of the Minerals Yearbook. COAL The injury-frequency rate for the coal-mining industry of the United States increased less than 2 percent, according to reports received by the Bureau of Mines. The number of fatal and nonfatal injuries per million man-hours in 1962 was 45.86, based on final data for anthracite mines and preliminary data for bituminous coal and lignite mines.

Jan 1, 1963

By Fred N. Kissell

In This Chapter [Early indicators of a gas problem How the methane hazard is reduced Ventilation principles for gassy tunnels Monitoring for gas Eliminating ignition sources and The all-important human factors component] This chapter gives guidelines for preventing methane gas explosions during tunnel construction. Emphasis is placed on assessing the hazard potential, on ventilation principles, and on monitoring for gas. The chapter also emphasizes the importance of human factors in reducing explosion risk. Ensuring safe conditions is much more than just good engineering design. It also involves the every-day vigilance of those working underground. This does not imply that the engineering design can be ignored, only that the job of providing safe conditions has just begun with design. EARLY INDICATORS OF A GAS PROBLEM For the engineer planning a tunnel project, reliable early indicators of methane are scarce. How-ever, the local geology can often provide some information.2 Carbonaceous rocks and tar sands are a likely methane source. Gas is also a distinct possibility if it is known to be present else-where in the same sequence of geologic formations. Swampy areas, sewerage systems, and landfills are also candidates because the decomposition of organic materials produces methane. The gas in a tunnel can originate in the strata being excavated, or it can migrate a considerable distance from adjacent strata. Test borings at the project site can also serve as initial indicators of gas. Methane has no odor, but may be emitted along with gases that do. If gas is emitted from the borehole, a sample may be collected by inserting a tube into the hole as far as possible and pumping the gas out. The gas sample should be collected in a sampling bag or canister for later analysis by a chemical laboratory.3

Jan 6, 2006

In the interest of safety in metal mining, the Bureau of Mines recommends: That underground metal mines be equipped with a main fan in a fireproof housing, located preferably on the surface. The fan installation should be designed to ventilate the mine adequately throughout and to permit prompt reversal of direction of air flow. Many metal mines depend for ventilation upon natural flow of air, assisted by the exhaust from pneumatic drills and by compressed air blown into the workings. Others also ventilate separate headings or sections with fans and blowers. Relatively few have o mechanical ventilating system that controls the coursing of air throughout the mine.

Jan 1, 1939

By Powell. Alfred R.

"An investigation has been made of the applicability to a variety of coals, other than those from Illinois, of the Powell and Parr method of analysis for the forms of sulphur in coal.A complete study was made of the sulphur in the following coals:- Upper Freeport, Pa.; Pittsburgh seam, Pa.; Pocahontas No. 3, W, Va..; Letcher Co., Ky.; Morgan Co., Tenn.; and Cherokee Co., Kan.The method of analysis gave excellent results when applied to these coals. In the determination of pyrite, the iron-sulphur ratio checked in every case with the theoretical. After the extraction of the pyrite and sulphates, the remaining sulphur was proved to be organic in nature.This work indicated that sulphur exists in coal in three typical forms: - pyrite or marcasite, sulphates, and organic sulphur. A study of the changes which these forms undergo during coking has been made on a variety of coals, and the following five classes of reactions established.First. Complete decomposition of the pyrite and marcasite to ferrous sulphide, pyrrhotite, and hydrogen sulphide. This reaction begins at 300°C., is complete at 600 °C., and generally reaches its maximum between 400 and 500°C."

Mar 1, 1920

By L. C. IlsLey

A n'Ulllber or operators have installed f'lBJ!le-proot or so-called exploaion­ proot electrical outfits, under the impression that such equipments met· all of the reqiirements of the Bureau of Mines as regards safety, There a.re todq in gaseous mines a large nwnber of euipments that have not been approved by the Bureau ot Mines, and unless mod1f'iecl could not receive sucl1 approval.. These e qu.ipments represent in pa.rt the product of manufacturers whil ha.ve never submitted. equipments for insri?ction or tests. and iri pat types developed. previous to the safety work or the bureau. Sometiu.es saleimen advocate the use of unapproved. types in gaseous mines in place of Bureau of Mines approved outfits, the purchase price beini slightly less than approved types,

Sep 1, 1922

In the interest of safety ii: coal mining, the Bureau of Mines recommends: That all active underground coal mines, whether working or idle, have one or more fans in continuous operation. The capacity and installation shall be such that the entire mine workings are adequately ventilated at all times. Main fairs shall be located on the surface in fireproof housing offset from the line of any mine opening. The housing shall be provided with ample pressure-relief doors or other devices easily opened by the force of an explosion. The installation shall permit prompt reversal of air flow. For mines that liberate gas, the fan shall have at least two independent sources of rower immediately applicable. Ventilation of underground workings in coal mines is needed whether or not explosive gas is present. Natural ventilation is unreliable and often uncontrollable. Main fans should be on the surface; if they are in the mine, fire or explosion may make access difficult or dangerous and render the installation inoperative.

Jan 1, 1939

By Howard M. Stainer

Jan 1, 1963

By Howard M. Stainer

[Cover Page]

Jan 1, 1963

By M. J. Brnich

The purpose of this US. Bureau of Mines study was to assess the ability of trainees to don an unfamiliar self-contained self-rescuer (SCSR) after having become familiar with how to put on a different type of apparatus. Prepractice instruction was the same for all individuals learning to put on a device: a step-by-step, hands-on talk-through using the "3+3" method. Subjects were assigned to groups that had their initial donning instruction derivered on either the Draeger QXY-SR60B or the CSE SR-100. Trainees&apos; performances were then evaluated using the other model. Donning trials were analyzed using a number of measures. It was found that SCSR design had a moderate influence upon how well the doming task transferred.

Jan 1, 1992

By Sean Gallagher, Rhys Llewellyn, Jay Mattos

This paper contains the results of an examination of accident, injury, employment, and production information reported to the U.S. Department of Labor&apos;s Mine Safety and Health Administration (MSHA) and provides information on some of the measures longwall mine operators are using to prevent accidents In all industries, technological advances play a key role in determining those who will survive as competitive participants in an increasingly global marketplace. While mining is among the most basic of industries, technological change is neither unfamiliar nor unwelcome to miners. Historically, technological advances in mining, particularly coal mining, have tracked closely with fluctuations in demand. In the early 1900&apos;s, coal accounted for more than three quarters of all the fuel consumed in the U.S. To meet this tremendous demand, underground cuffing machines were introduced, resulting in faster, more efficient coal extraction. Transporting coal to the surface, however, remained labor intensive. In the 1920&apos;s, nearly all underground coal was still being hand loaded. Demand for coal then declined as the price of oil, natural gas, and electricity became competitive. In the late 1930&apos;s and throughout the duration of World War II, coal demand and production was high. By 1940, more than half the coal mined was being mechanically conveyed to the surface. In 1948, the continuous mining method was introduced in the U.S., further accelerating the extraction process. By the 1950&apos;s and 1960&apos;s, however, coal production again declined as railroads converted to diesel fuel and gas and oil provided a larger share of the home heating market. Underground coal mines required even more mechanization to remain competitive as an energy source. The first longwall system was introduced in 1960. By 1995, longwalls were producing more than 189 million tons of clean coal annually, surpassing continuous mining production for the second straight year. The mining of coal and other materials has not come without a huge loss of life and considerable human suffering. More than 103,000 workers died from injuries in U.S. mines in the last 85 years. Between two and three thousand miners died each year from the turn of the century until 1931, many from underground fires and explosions. The U.S. has witnessed a tremendous drop in fatalities in underground coal mines. Credit for that is due to safety inspections and enforcement activities, better safety awareness and practices among management and labor, improved ventilation, the use of safer equipment, and increased mechanization which removed many miners from the hazards at the face and also reduced the size of the mining work force. There is little doubt that longwall mining has greatly increased underground coal mine productivity. The degree to which longwall mining has contributed to a safer work environment for underground miners is more difficult to ascertain.