Search Documents

By N. H. Coates

A small, special-purpose centrifugal compressor was developed to circulate 60 pounds per hour of helium at 1,000° F and 250 psig because standard, commercial units were not available. Performance characteristics of this compressor were determined at helium flows of 2,000 to 18,000 std cu ft per hour, pressures of 100 to 250 psig, and temperatures of 100° to 1,000° F. This range is 2 to 90 actual cu ft per minute. Several graphs show the adiabatic head developed by the compressor over this wide flow range at various combinations of temperature and pressure. A compressor performance map relates pressure ratio to mass flow, temperature, pressure, and speed. This map can be used to accurately predict compressor performance factors within the range of operating conditions covered by the experiments.

Jan 1, 1963

By Michael A. Trevits

Mine fires can be especially perilous because toxic products can quickly spread well beyond the fire zone thereby exposing all underground miners to dangerous and deadly conditions. Since November 1998, there have been six major underground coal mine fires or explosions in the United States (Willow Creek (twice), Sanborn Creek, Loveridge No. 22, West Elk and the Jim Walter Resources No. 5 Mine). In each case, the entire mine or specific areas of the mine had to be sealed due to the build-up of dangerous gases and the fear of uncontrolled spread of the fire. Effective placement of mine seals can deprive a mine fire of oxygen and is often followed by water flooding or injection of inert gas into the affected area. When access to the fire zone is impossible because of safety reasons, airtight mine seals can be constructed, in the area of the fire, remotely from the surface through vertical boreholes. Remotely constructed mine seals are commonly made from cementitious material. Since these mine seals are typically erected blindly, it is difficult to determine if mine roof-to-floor and rib-to-rib closure has been obtained. This paper provides a review of the available materials and technology used to remotely construct mine seals through vertical boreholes.

Jan 1, 2002

By Murray Jacobson

The respirable dust standard in the Federal Coal Mine Health and Safety Act of 1969 is designed to prevent disability and death from coal workers' pneumoconiosis. Beginning June 30, 1970, the operators of coal mines were required to maintain the average concentration of respirable dust in the active workings at or below 3.0 milligrams of dust per cubic meter of air. The standard is reduced to 2.0 milligrams per cubic meter after Dec. 30, 1972. This paper presents the equipment and procedures used by the coal mine operators in implementing the respirable dust sampling program established by the Secretary of the Interior and the Secretary of Health, Education, and Welfare and shows the effect of the law, during the first year, on the reduction of dust levels in selected mines. The system employed by the Bureau of Mines for analyzing and processing the dust samples is also presented.

Jan 1, 1971

By R. L. Hopkins

Some typical thiacyclopentanes and thiacyclohexanes were synthesized to provide reference compounds needed for the identification of sulfur compounds in crude oils. Two general methods of synthesis were employed: (1) cleavage of 2-alkyltetrahydropyrans with hydrogen bromide followed by the reaction of the resulting dibromoalkanes with sodium sulfide and (2) the catlyzed reaction of cyclic ethers or 1)4-or 1)5-alkanediols with hydrogen sulfide. Both methods produced mixtures of 2-alkylthiacyclopentanes and 2-alkylthiacyclohexanes with 2-alkyltetrahydropyran as the starting material. The structures of the reaction products were established by analysis for sulfur; desulfurization; gas-liquid chromatography (GLC); mass, infrared, and nuclear magnetic resonance (NMR) spectra; and an alternate synthesis. The synthesis of the cyclic sulfides contributed substantially to the identification of 10 members of this class of sulfur compounds in crude oil.

Jan 1, 1967

By J. C. Hartley

The most important single operation in mining is the ventilation of underground areas in a manner conducive to the health and safety of employees. Adequate volumes of pure air must be supplied at the working faces, along the haulageways, and wherever men work, so as to dilute and carry away the methane liberated from the coal and adjoining strata, noxious gases evolved by the use of explosives, and the carbon dioxide exhaled by men and formed by oxidation of carbonaceous material, as well as any other gases, and also dusts which may be found in mine workings. A sufficient quantity of air must also sweep abandoned or worked-out areas of the mine to prevent the accumulation of gases, where sealing methods are not utilized to isolate old workings. Air, in a quantity adequate to meet the needs of the particular mine to which it is applied, is necessary, and supplying it can be made very expensive through failure to observe good practices in its direction and apportionment." Leaky stoppings, doors, and overcasts rob the working faces of air and add to the ventilating cost by burdening the fans with fugitive air,

Jan 1, 1944

By J. Torma-Krajewski, M. Lehman

In 2005, NIOSH and Badger Mining Corporation entered a partnership to implement ergonomic interventions, including a systematic process, to address exposures to risk factors that may result in musculoskeletal disorders or other types of injuries/illnesses. As a result of this partnership, an ergonomics process was integrated with the existing safety and health program to promote an on-going application of ergonomic principles, and over 40 task-specific interventions were implemented during the first year of the process. This paper presents details of the process integration, and several examples of task-specific interventions that reduced exposures to risk factors.

Rapidly identify unstable mine waste embankments and similar dam structures. Approach Aerial photography, geotechnical instrumentation, and telephone or satellite data transmission are used to supplement walk-around inspect ions. How It Works Embankment stability and other indicators of structural integrity are evaluated using aerial photography, and on-site unattended instruments and data transmitting systems. Evidence of external movement and water seepage is obtained from aerial photography and photogrammetric evaluation techniques. Surface points marked by stake- mounted targets are monitored photographically at time intervals of several weeks or months. Photographic measurements of x, y, and z coordinates of these points are obtained from flying a series of photo-runs over the dam.

Jan 1, 1979

By M. G. Zabetakis

This publication presents a simplified graphic method for determining the explosibility of mine atmospheres under mine-fire conditions from mine- atmosphere composition data. Sometimes it is necessary to seal part of a mine during a fire to exclude air and thus extinguish the fire. Unfortunately, liberation of methane and formation of hydrogen and carbon monoxide in the sealed area may create an ex- plosive or flammable atmosphere if enough oxygen is present to support combustion. On the other hand, the oxygen concentration may be reduced through combustion processes and the concentration of inert gases (nitrogen and carbon dioxide) increased enough to render the atmosphere within the sealed area non-explosive. Before an area is unsealed, it is extremely important to know if the sealed atmosphere contains Flammable gases in proportions that might form explosive mixtures when air is introduced. If an explosive mixture forms and the fire is rekindled, a gas explosion will result. Various experimental methods may be used to determine the explosibility of a particular mine atmosphere; however, these methods usually are impracticable in the field.

Jan 1, 1959

By L. D. Tracy

For many yeirs natural gas has been the principal fuel used in the he·1 ting furnaces in those mills located in the. Pi t-c;s. b.urgh district· \7hich manufacture bolts ., nuts, rivets, pick$, mattocks and srr.&11 for6ine;s. For a nUI.1"'.::>er of years the steady supply of this fuel has been more or less interrupted owing to the increased4and f·or d9mes tic use and to the increasing difficulty in securing an ad.eq_ua te c.1mount of natural gas. This condition has led a number of the steel compa.nies to substitute -oulvsrized coal a.s a fuel for the.furnaces. Elaborate irista.llations have been made for pulverizing tne coal ar!d _ coriveyi16 i -c to the fur:waces. • Soon after the furnaces ·-:commenced .. to operate ·,Vi th :pulverized coal, large quanti ties O::f.' fine dust beg.::in to accumulate on the platforms over the fu:rna. ces, the. roof trusses, on the outside of the va.rious· pip·e ·line electric cables a.i.1.d even on the roofs of the buildings. Some of tha comi:,a.n:;.0s, becomin·g alarmed, requested the Bureau of ;Unes to rr.c1ke an investigation to ascertcliin the.· licibili ty of this dust to cause an explosion.· Nhi le conducting this inves ti ga ti on,· an explosion· occurr-2! d in a.nothe:2 nill ·,7hich caused he death of one man and severely burned t;io others. Eleven sc1nrcles of the dust (which for convenience has been termed "mill d.ust 11 ) from various locations in the different mill' buildings were taken and submitted to chemical analyses, microscopic examination and also to flame and explosion tests. From the chu,1ica.l analyses it was found that· the volatile matter in th..:: dusts xanged -from 6.3 per cent to 23,54 per cent, fixed carbon from 50.88 per cent to 67.08 per cent and ash from 32.29 per cent to 32.16 per centw

Dec 1, 1919

By Gregory Krohn

This report investigates the effects of adding a layer of extra padding to the palm area of leather gloves typically worn by low seam coal miners. The first study showed that added glove padding provides more potential protection but does not affect manual dexterity. The second study, in a simulated low seam coal mine, showed no significant differences using padded and non-padded gloves in crawling, shoveling, timbering, and cart pushing task completion times. In general, subjects preferred the padded gloves although they expressed some complaints about awkardness and loss of sensitivity. Recommendations are given for the design of padded gloves that will provide comfort, protection, and maximum hand sensitivity for miners.

Jan 1, 1980

By D. J. MacDonald

The Bureau of Mines investigated two alternative methods for treating a zirconium-bearing chloride-sulfate strip liquor to obtain reactor-grade Zr02. One method involves neutralization with NH3 and the other hydrothermal precipitation. The strip liquor was derived from zircon sand by a Bureau of Mines method for separating zirconium and hafnium via solvent extraction with a tertiary amine. Neutralization with NH3 to precipitate hydrous zirconium oxide required 0.9 to 1.1 g NH3 per gram of zirconium. The NH3 can be recovered for recycle. Zr02 that met reactor-grade specifications was produced by precipitation with NH3? Hydrothermal precipitation of Zr02 from strip liquor required that the solution be maintained at 2600 C and 680 psi for 10 min and in a non-corrodible pressure vessel. In bench-scale experiments both methods gave-zirconium recoveries greater than 99 pct.

Jan 1, 1984

By Mary A. Barrett

The Bureau of Mines conducted a laboratory-scale investigation of grouting mixtures containing iron or aluminum to determine the existence of health or explosion hazards, due respectively to oxygen depletion or hydrogen emission. Mixtures containing iron created an oxygen deficiency in less than 24 hours and released small amounts of hydrogen; a health hazard could occur but only under extremely unfavorable conditions. Mixtures containing aluminum released little hydrogen and consumed little oxygen; however, if improper on-site mixing yielded high local metallic aluminum concentrations, enough hydrogen might be released to produce an explosive atmosphere in a confined space.

Jan 1, 1969

By A. W. Khair, L. D. Gehl

"This paper describes the study of bit wear characteristics on three types of rock namely Tennessee sandstone, Berea sandstone and Indiana limestone. High content of quartz with quartz cement in Tennessee sandstone causes removal of material from the bit body and dam2ge to the tip of the bit resulting into excessive weight and height loss as compared to other two types of rock. The drum speed and water spray pressure do not contribute significant effect on bit wear. The polycrystalline compact diamond (PCD) tipped bits are more wear resistant than the ordinary tungsten carbide (WC) tipped bits, but, due to wider body of PCD bits, the wear rate increases particularly at greater depth of cut. INTRODUCTIONThe impact of bit-rock interaction during the cutting process in underground coal mines has always attracted the-interests of mining operators, researchers and the manufacturers. Coal cutting bears directly on airborne coal dust generation which causes ""black lung"" in coal workers. On the other hand, rock cutting generates frictional sparks causing face ignitions. The bit wear not only produces airborne rcspirable coal dust , but also affects the productivity, safety and economy. Hun and Evans (J) concluded that the point attack bits have greater ignition potential than the conventional wedge shaped bits. The results of a study (2) suggested that after 7% of weight loss, the bit should be replaced. In a survey study (3), it was found that the bit consumption of bit had an effect on the productivity and utilization of the continuous miners. The mining industry is yet to receive a solution which could provide them with optimum operating parameters for coal cutting machines in underground C9al mines.The study was, therefore, taken up to determine wear characteristics as influenced by the rock propenies and varying operating parameters. For the purpose of this study, three types of rock, Tennessee sandstone, Berea sandstone and Indiana limestone were used. The machine operating parameters included (i) drum speed, (ii) water spray pressure and (iii) bit type. Besides studying the wear characteristics, the effects of these parameters on the required cutting force, specific energy consumption, acoustic emission generation and bit temperature rise were also studied. Also, the preliminary experiments were performed to compare the bit wear between PCD and WC tipped bits."

Dec 1, 1995

By H. H. Schrenk

The safe use of a refrigerant or any substance depends on knowledge of its pertinent properties and conditions of use; therefore some of the properties of refrigerants that are related to life, fire, and explosion hazards are discussed herein. These data serve as a basis for suggested control measures in the use· of refrigerants. The properties of refrigerants may be broadly classified into three main groups: (1) Those important for refrigeration, (2) those significant from the standpoint of confining the refrigerant, and (3) those that become important if the refrigerant escapes from the :machine or container. The first group of properties, such as latent heat of vaporization, specific heat of vapor, specific heat of liquid, etc., is not considered to be directly related to safety and is not discussed here. The second group, those properties important in confining the refrigerants, has particular significance because· it relates to "built-in" safety. This group is emphasized because it is believed the soundest procedure in designing equipment is to give due consideration .to both the health and safety hazards likely to be associated with the equipment. Furthermore, the toxicity, fire, and explosion hazards are controlled as long as the refrigerant is confined. Some properties of this group are (1) stability, (2) corrosiveness, (3) boiling point, (4) pressure developed in the system, (5) warning odor or irritation, and (6) ease of detection. The third group includes such properties as toxicity (of compound and decomposition products), irritating action, and explosibility.

Feb 1, 1942

By William Wiehagen

This trainer?s guide is designed as a reference manual. The purpose is to offer information and examples to skills trainers to assist them in structuring training for new operators of Walk-Thru roof bolting machines. Trainers can use this manual as a resource for helping trainees learn, understand, and apply knowledge and skills. In this sense, the guide is not prescriptive. It is designed to offer information and trigger ideas on what might be done to accelerate learning to those who are new to the roof-bolting task. On-site trainers can modify this guide to fit their conditions, machines and equipment, and work procedures. They can integrate roof control plans, company policies and procedures, and operators? manuals from the manufacturers of the original equipment into this guide. Every trainee is different and will come to the job with varying levels of relevant knowledge and skills. The trainer?s decisions on where to start, how to organize the on-the-job and classroom training portions, and when and how to offer different aspects of the training will be based on (1) a pretraining assessment of the trainee?s knowledge and skills and (2) the trainer?s experience in conducting skills training. The ?Skill Check? section might be useful for deciding where training should start among miners who have underground experience but limited knowledge of roof-bolting techniques. Every job carries a learning curve and likely has a number of ?teachable moments? where significantly new knowledge and skills can be learned.

Aug 1, 2006

By H. O. McDonald

Solutions containing Cr6+ and sulfuric acid are used in a number of surface-finishing operations. Substantial quantities of chromium and copper are lost and pollution problems are created when the spent solutions are discarded. To minimize the undesirable environmental effects while improving secondary resource recovery technology, the Bureau of Mines is conducting research to detoxify and recover metals from these solutions. Spent etchants are treated to remove copper and reduce Cr6+ to Cr 3+ in an electrolytic cell. The anodes and cathodes are granulated coke. The spent solution is continuously pumped through the electrodes. Hexavalent chromium is reduced to trivalent chromium, and copper is recovered at the cathode. Reoxidation of Cr3+ at the anode was not observed. The removal and recovery of copper reduction of Cr6+ lessen chemical demand and increase efficiency in waste in treatment operations associated with the use of these solutions.

Jan 1, 1980

By J. M. Stuve

Calorimetric determinations of the low-temperature heat capacities, standard enthalpy of formation, and high-temperature enthalpies were made of (Na20)4 ?Fe20,(c). The resulting values of entropy (S°), enthalpy of formation (?Hf°), and free energy of formation (?Gf°) at 298.15° K are 104.676 cal/deg mole, -656.2 ±.kcal/mole, and -603.4 A kcal/mole, respectively. Tabulations of Cp°, S°, - (G°-H°298)/T, H°-H°298, ?Hf°, ?Gf°, and log Kf are given to 1,200° K.

Jan 1, 1971

Reduce dust on long wall faces by using a gob curtain to lower air leakage Into the gob and raise the airflow along the face. Approach A brattice curtain (gob curtain) Is hung between shield #1 and the rib in the headgate entry forcing the ventilating air stream to make the 90° turn and stay on the face side of the shields rather than leaking into the gob. How It Works Air leakage is greatest in the headgate area because the gob behind the first few shields remains open due to the roof bolts in the headgate entry. In addition to the open gob, there is a large gap between shield #1 and the rib. Prevention of air leakage behind the shields is accomplished by the Installation of a curtain between the first shield and the rib extending from the roof to the bottom. The curtain Is advanced with the shield line each pass and is helpful In maintaining a sufficient air quantity along the face. The biggest Improvement due to this curtain is seen in the first 25-30 shields where the Increased air volume lowers dust concentrations through dilution.

Jan 1, 1981

By E. C. Baker

The Bureau of Mines estimated the economic feasibility of investing in a directional hole methane drainage project in the Pittsburgh coalbed for 5 yr in advance of mining. This report estimates the capital investment and operating cost of recovering 325 MMft3 of methane gas per year and the selling price of approximately 317 MMft3 of gas per year. The labor, equipment, and supply requirements were determined from those of a previous directional hole drilled at the Emerald Mine, near Waynesburg, PA. The cost of equipment, materials, services, and labor are in third quarter 1982 dollars. They were obtained from vendors, contractors, and the U.S. Department of Labor. Findings indicate a total capital investment of $1,381,160. Annual operating cost amounted to $167,690. At a wellhead price of $2.05 per thousand cubic feet, the sale of approximately 317 MMft3 of gas per year results in a rate of return on investment of approximately 25 pet.

Jan 1, 1984

By G. R. Hopkins

"A new record in fuel efficiency at petroleum refineries was achieved in 1935, when an average of only 615,000 B. t. u. was needed to refine a barrel of crude oil, compared with an average of 638,000 B. t. u. in 1934 and 829,000 B. t. u. In 1925. (See fig. 1.)Refiners have made almost uninterrupted progress in firing efficiency during the last decade although much of this gain was brought about by improved technique and greater use of heat exchangers and pipe stills, the determining factor was the trend in crude runs to stills. Most plants can increase their crude throughput materially with but small increase in fuel consumption. Consequently, in years in which crude runs have increased substantially, average requirements have declined; but in years in which crude runs have decreased, the average has tended upward. This conclusion is confirmed by figure 1, which shows that there has been but one minor exception to this rule in the last 10 years.Technical progress in fuel efficiency may be illustrated by comparing crude runs and total B. t, u. consumed. Between 1925 and 1935 crude runs to stills increased 31 percent, but the total quantity of heat required did not increase; in fact, it declined slightly.The trend of modern still construction is from shell stills, in which a large body of oil is heated, to tube stills, in which the heat comes into much closer contact with the oil. In 1935 the total capacity of operating pipe stills increased about 4 percent; this increase, though small, probably was related to the gain in average efficiency.The Increased use of heat exchangers and their role as fuel savers have been discussed in previous reports of this series. It is sufficient to say that refiners with insufficient exchange capacity added as much in 1935 as their budgets would permit."

Jan 1, 1937