Search Documents

By R. L. Grant

An investigation was undertaken by the Bureau of Mines to determine the relationship between freespace and ignition probability for borehole shots. A series of experiments was concluded which covered six freespace conditions for a pemissible explosive in a 3/4-inch borehole and encompassed some 700 shots. The results were analyzed statistically. From the analysis of variance, it was concluded that the freespace means were different and that this conclusion is not impaired by possible differences in the explosives used. Within the limitation of this experiment, a definite relationship was found between the freespace and the ignition probability. Specifically, the incendivity increases with increased freespace up to a maximum; beyond this maximum there is some indication of decreasing incendivity. Further investigations are in progress to establish whether the effects of freespace on ignition probability reported here are applicable to the large test gallery, INTRODUCTION A borehole loaded with an explosive charge is a common feature of the routine gallery tests for determining the permissibility of coal-mine explosives, of Experimental Coal-Mine shots, and of the small steel cannon shots used in connection with certain research programs on the ignition of firedamp (6, 10).6/ The question of the interrelationship of freespace, weight of charge, and ignition probability of the methane-air atmosphere has been raised

Jan 1, 1959

During the summer of 1973 we were asked to perform a theoretical investigation of the propagation of low frequency (LF) radio waves down deep (10,000 feet) hoistshafts* for the case where the hoist cable ("rope") is the only metal conductor present. Propagation is by means of the TEM coaxial mode of transmission in which the hoist cable serves as the inner conductor and the surrounding rock acts as the outer conductor. Since the rock is a relatively poor electrical conductor the current in the outer conductor of the coaxial line is not confined to a very thin surface layer as in a metal coaxial cable, but spreads radially to a distance that is generally many times the shaft diameter. This feature of the wave propagation requires a more sophisticated theoretical treatment than the approximate skin-depth theory that is adequate for metal coaxial lines. In this Part we treat the hoist shaft wave propagation loss, characteristic impedance, and the field current distributions in the surrounding rock medium. We also show that the large penetration of the wave into the rock outer conductor does not present a difficult problem with regard to coupling the transmitter or receiver to the transmission line with a minimum of insertion loss, but that the large impedance mismatch caused by the capacitance termination between the cage and shaft wall may well be the most significant contribution to overall system loss. Inductive coupling and impedance matching to the hoist rope/shaft transmission line are also treated briefly. Preliminary results indicate that a broad minimum in overall system loss should occur between 100 kHz and 1 MHz, possibly centered around 300 kHz. Further work is needed to better quantify this signal loss behavior, compare it with hoist shaft electromagnetic noise spectral data recently acquired by NBS, and identify the most favorable operating frequencies.

Jan 1, 1974

By James R. Aggson

The theoretical relationships that are used to calculate in situ rock stress magnitudes and directions from borehole deformation data obtained during overcoring are based on the assumption that the rock is a linearly elastic material. Strictly speaking, this assumption is not valid in any rock. Thus, investigators using overcoring techniques must either accept various degrees of nonlinearity and the associated inaccuracies or use core testing techniques that address the problem and compensate for elastic nonlinearity. Previously developed test procedures for stress-relief overcores partially correct for nonlinearity. This Bureau of Mines paper describes a test procedure that completely corrects for elastic nonlinearity in stress-relief overcores.

Jan 1, 1977

By Harry K. James

Experimental studies of the physical and explosion characteristics of pure hydrazine nitrate and multicomponent systems containing hydrazine nitrate, supplemented with an extensive Literature survey, are presented. Such proper- ties as melting point, heat of fusion, density, viscosity, surface tension, thermal stability, decomposition process, detonation velocity, impact sensitivity, and TNT equivalence are included.

Jan 1, 1970

By L. B. Pankratz, R. Barany, W. W. Weller

Experimental determinations were made of the heats of formation at 298.15 ° K of cuprous ferrite and cupric ferrite ; the heat capacity of cuprous ferrite was measured over the temperature range from 50 ° to 298 ° K and the entropy at 298.15 ° K was evaluated ; the heat contents of cuprous ferrite and cupric ferrite above 298.15 ° K were measured to 1,500 ° K and 1,100 ° K , respectively . These thermodynamic values were combined with other pertinent data to obtain heat and free energy of formation values at high temperatures . The stability of the two ferrites with respect to their constituent oxides is discussed . Thermodynamic values are included for the decomposition of cupric ferrite to form cuprous ferrite , magnetite , and oxygen .

Jan 1, 1964

Provide reasonably priced, reliable fire protection for large walking draglines. Approach Fire hazards on large draglines were analyzed, then appropriate automatic fire sensing and suppression systems developed and in-mine tested. How It Works Five fire hazard areas identified for special attention are: electrical control room, high voltage transformer enclosures, circuit breaker rooms, collector ring/roller path area, and the automatic lubrication rooms. Automatic fire sensing and suppression systems were separately designed for each area. The design of each system was tailored to the hazards and equipment protected. Spot thermal sensing and Halon 1301 suppression were specified for the electrical

Jan 1, 1981

By N. A. Gokcen

In this Bureau of Mines report, appropriate equations correlating the activity of water with the activities of electrolytes in binary and multicomponent solutions have been derived for computer calculation. It was found that the half-integer power series are far superior to the integer power series, for both types of series having the same number of terms. The pro-posed method of calculation is capable of accurately yielding the activities of all components from the measurements of the activity of a single component at various concentrations. This method replaces the cumbersome and objection-able method of graphical integration of the Gibbs-Duhem equation. Two novel methods are proposed for determination of activities of electrolyte solutions important in hydrometallurgy; (1) Water vapor pressure measurement by differential pressure transducers having an accuracy of 0.001 pet, and (2) transpiration method with an inert gas bubbled through concentrated solutions followed by the analysis of the evaporated and redissolved electrolytes with specific ion electrodes having a sensitivity of ±10-10 molal. The first method is suitable for nonvolatile electrolytes, and the second, for volatile electrolytes such as hydrogen halides, HN03, H2S03, etc. The existing methods of estimation of ionic activities have been surveyed, and the best method has been selected, discussed, and summarized.

Jan 1, 1979

By Leon W. Dupuy

"INTRODUCTION Scheelite occurring in tactite at the Black Rock tungsten mine, near Benton in Mono County, Calif., was investigated by the Bureau of Mines in cooperation with the Geological Survey as part of their search for additional sources of supply of strategic minerals authorized under the Strategic Materials Act. 3/4/The work accomplished by the Bureau, and the assays of samples taken are described in this manuscript. The ore found aided materially in prolonging the operating life of the mine during the recent national emergency, supplying much-needed tungsten for war use. ACKNOWLEDGMENTSIn its program of investigations of mineral deposits, the Bureau of Mines has as its primary objective the more efficient utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. The Mining Division, under the direction of Lowell B. Moon, chief, conducts preliminary examinations, performs the actual development work, and prepares the final report. The Metallurgical Division, under the direction of C. C. Ralston, chief, analyzes samples and performs beneficiatibn tests."

Mar 1, 1948

By Daniel Edelstein

Demand for arsenic trioxide dropped markedly during 1983, primarily as a result of a 27% reduction in cotton planting. As an oversupply of arsenic trioxide developed, prices declined for both domestic and imported material. Domestic Data Coverage.-Commercial-grade arsenic trioxide and arsenic metal were produced by only one U.S. company, which voluntarily reported its production to the Bureau of Mines. To prevent disclosure of proprietary data, the production data have been withheld.

Jan 1, 1984

By A. Wahab Khair, W. M. Devilder

"This paper presents an analysis of fragment size distribution and characteristics of fracture surface in coal cutting using a rotary coal cutting simulator. Coal cutting by a drum type continuous miner was simulated in the laboratory. A series of tests along both the face and butt cleat direction of coal under different operating and in-situ conditions were performed. In each experiment the cut surface was photographed microscopically and the coal cuttings were collected and sized. Data were used to show how and to what extent various parameters effect size distribution of the coal cutting and how this correlates with the characteristics of the fracture surface. This study resulted in establishing a number of distinct correlations between the size distribution and fracture surface. These correlations were primarily based on the degree of interaction between adjacent bits and the amount of bit-coal interaction taking place on the cutting path. Some of the major results of this study are as follows:Zones of bit-coal interactions proved vital toward understanding the effect the conical bit has on the fragmentation process. This in turn led to the identification of areas which are responsible for the production of fines and generation of respirable dust.The various parameters employed in the coal cutting experiments which showed a strong effect on the coal fragment size distribution were: bit type, bit spacing, depth of cut, in-situ stresses, and cleat orientation. Bit angle and cutting head velocity exhibited the least effect and no correlation was established.From this study it is obvious that the key to achieving efficient coal fragmentation is to limit the degree of bit-coal interaction that takes place throughout the bit path while causing maximum interaction between adjacent bits. Accomplishing this not only increases the percentage of large fragments produced but limits the amount of secondary crushing that takes place in the bit path thus resulting in decreasing fines and consequently, the amount of respirable dust generated.Over 2,000 continuous mining machines (introduced in the 1950's) equipped with conical bits or point attach bits account for well over half of the United States' production from underground coal mines. Today, competition in the coal industry has increased, due mainly to coal market conditions and legal restrictions, thus placing an emphasis upon increasing production, efficiency and health/safety of the workers. Mine operators are always interested in finding the most efficient performance of continuous mining machinery to produce the largest amount of size of coal at the lowest cost. An increase of fine material sent to the cleaning plant can seriously overload the plant to the extent that plant efficiencies deteriorate significantly (1). Also, the difficulty and expense of cleaning very small particles often cannot be done economically and thus, thousands of tons of coal are sent to the refuse pile because of costly or ineffective cleaning facilities. It has been said, ""the efficient extraction of coal or rock implies breakage into a size range that contains a minimum quantity of very small sizes"" (2). All known fragmentation theories concur that more fragmentation requires more energy (3). So, the importance of reducing fines is already evident from an outlook upon efficiency.Now, let's consider another view point., duet generation."

Jun 1, 1988

By W. P. Haynes

The Bureau of Mines has been studying a modified steam-iron process using coal-derived producer gas for making either hydrogen plus carbon monoxide or methane. To provide a guide for this experimental study, compositions of equilibrium product gases for the reaction of steam plus carbon dioxide with iron were calculated and are discussed in this report. The calculations, which are described in this report, are based on thermodynamic data in the literature and cover temperatures from 800° to 1,300° K., pressures from 1 to 30 atmospheres, and hydrogen-to-carbon atomic ratios in the gas of 4 to 12. The equilibrium gas compositions are discussed in regard to making hydro-gen, carbon monoxide, and methane in the oxidation step of the modified steam-iron process. From the viewpoint of thermodynamics alone, assuming the reactions reach equilibrium, the discussion considers the effects of temperature, pressure, and composition of feed gas upon the composition of the product gas, the degree of oxidation of the iron, and the possible deposition of carbon. The results indicated the following: (1) Nearly all the carbon can be converted to methane at low temperatures (800° to 900° K.) and high pressures (over 20 atmospheres); (2) to obtain high yields of synthesis gas, high temperatures are required. For example, at 30 atmospheres, a temperature over 1,200° K. is required to convert 60 percent of the steam plus carbon dioxide to hydrogen plus carbon monoxide. Lower temperatures may be used at lower pressures) (3) oxidation of the iron increases with increasing pressure and decreases with increasing temperature; and (4) process conditions favoring carbon deposition were found within the range of variables studied, but it is thermodynamically possible to operate the oxidation process with steam and carbon dioxide outside this range of carbon deposition.

Jan 1, 1961

By Henry E. Blake

Defluorination studies on refractory fluoride - bearing compounds and minerals , particularly on partly defluorinated residues from high - temperature pyrohydrolysis , required a dependable and reasonably accurate analyticalcontrol method for the analysis of fluorine . The difficulty in liberating fluorine from the fluorides of metallic elements such as aluminum, zirconium , and rare earths by steam- distillation can be largely overcome if the distillation is made from a sulfuric - phosphoric acid solution of a sodium carbonate fusion of the sample material and if the distillation temperature is maintained at about 155 ° C. The data presented in this paper show that liberation of fluorine by this method is more complete and proceeds more rapidly than by usual distillations from perchloric or sulfuric acid alone or a mixture of phosphoric and perchloric acids . Fluorine in amounts ranging up to about 140 mg can be recovered by collecting only about 300 ml of distillate . Determination of fluoride in the distillate is made by the usual thorium nitrate titration .

Jan 1, 1963

By Robert F. Randolph, Dana C. Reinke, Richard L. Unger

Purpose The NIOSH Hearing Loss Simulator is a software training and communication tool for promoting hearing loss prevention. It allows a user or trainer to demonstrate the effects of noise exposure on hearing without experiencing an actual noise-induced hearing loss. Estimates of the effects of different levels of noise exposure are based on the American National Standard Determination of Occupational Noise Exposure and Estimation of Noise-Induced Hearing Impairment, otherwise known as ANSI S3.44. This standard specifies the predicted hearing loss for noise-exposed populations of individuals based on risk factors that include gender, age, sound levels (in A-weighted decibels or dBA), and years of exposure. Algorithms specified in the standard were derived from empirical studies of populations that had no exposure to loud noise and other populations that had experienced various levels and durations of noise exposure. This manual explains the major objectives that can be addressed with the simulator and training scenarios that can be applied to real-life, real-worker scenarios. The majority of this guide explains the simulator's functions in detail. Simulator users are encouraged to read this manual while learning how to run the software. [ ] Training Objectives The main objective of the Hearing Loss Simulator is to increase motivation for taking effective hearing prevention action by demonstrating simulated noise-induced hearing losses. [The Simulator can also help teach the following facts about hearing loss. Hearing loss is affected by noise levels. Hearing loss worsens as the noise exposure duration increases. Hearing loss can become permanent. Hearing loss makes it harder to hear what others say. Most hearing loss is not caused by age. Speech is made up of both low and high pitch sounds. Hearing loss due to noise makes it harder to hear high pitch sounds. Hearing loss due to noise has less of an effect on hearing low pitch sounds.]

Jan 3, 2008

By John W. Buch

At a meeting of the Anthracite Investigations Advisory Committee in July 1944 at Washington, D. C., the initial work and objectives of the Anthracite Mechanical Mining Section of the Federal Bureau of Mines were discussed. It was learned that interest existed in an improved performance of mining thin, steeply pitching beds above the gangway by mechanical methods. One company offered the use of one of its mines for experimental work, and this offer was accepted. Following acceptance, an effort was made by Bureau engineers to devise a mechanical method with a performance better than that of a new hand method proposed by company engineers for an actual mining condition. The method proposed by the Bureau was to drive 30-degree slant chutes across a 10-foot bed pitching 85 degrees. These chutes were to be advanced by using a lightweight, compressed air-powered, shearing machine of German origin that had been tried in a flat Pennsylvania anthracite bed in 1934, and which did not then prove successful because of blasting difficulties. An attempt was made to obtain one of these machines from England, where it was known machines of this type had been used. Shortly thereafter John W. Buch was sent to Europe as a member of the Solid Fuels Mission to the European Theater of Operations organized by the Technical Industrial Intelligence Committee of the Joint Chiefs of Staff. Through his efforts the Bureau of Mines obtained two such machines, known as the Eickhoff model DEK, one from England and one from Germany. This report covers the preliminary testing of these machines in order to obtain mechanical operating data for use in determining the power requirements for cutting anthracite with machines of this design.

Jan 1, 1949

By N. C. Tomoeda, W. D. Bensema, J. W. Adams

Measurements of surface magnetic field noise were made at various locations over the Geneva Coal Mine near Price, Utah, on June 12, 1973. The locations selected were on the surface over emergency locator beacons underground at depths between 350 meters (1150 ft .) and 488 meters (1600 ft .) . The surface terrain where these measurements were made was mountainous, and access was difficult. There were no power lines within several miles, and the weather was clear; therefore, the magnetic noise levels were about as low as will normally occur. Results of measurements of distant sferics indicate rather sharp cutoff frequencies below which broad- band, impulsive noise is attenuated. The mechanism of propagation for this noise above the daytime cutoff frequency of 3500 Hz and the nighttime cutoff frequency of 1700 Hz is deduced to be a waveguide formed by the D or E layers of ionosphere as an upper plane and the earth as a lower plane. The measurement systems used are similar to those used earlier. The technique is to record broadband, analog signals, digitize the data, and use a fast- Fourier transform to obtain spectral plots. This tech- nique is novel in that it can measure simultaneously all magnetic field energy within a limited portion of the spectrum for a limited time, and, after processing, reproduce the events occurring in that time interval in great detail .

Jan 6, 1974

By Thomas J. Peters

The Danskin/South Fork Boise River study area is 40 air km southeast of Boise, Idaho. The 16,000-hectare, two-segment area is mainly underlain by Cretaceous-age granodiorite and an aplitic and pegmatitic complex of the Idaho batholith, Miocene-age rhyolitic tuffs and lavas, and late Tertiary-age basalt flows. No mineral resources were identified in the study area. One mine, The Flat Creek mine, which produced several ounces of gold and silver, was found in the study area. It is geologically similar to deposits in the Neal mining district, adjacent to the northwest corner of the area; gold mineralization occurs along east-northeast-trending faults and associated quartz veins, which dip moderately to steeply southeast, and within adjacent Cretaceous granitic rock. Samples indicate the Flat Creek deposit is not rich enough to mine underground, and near surface, open-pit-mineable deposit areas could not be identified. However, exploration is warranted there and also in the 7-km interval to mines in the Neal district, and for extensions of those mines. No evidence of geothermal activity was observed, although there are hot springs in the vicinity. Some alluvial (placer) samples from the interior of the study area contained free gold, but no substantial gravel deposits were seen.

Jan 1, 1993

By Wallace W. Roepke

Research on coal cutting at the Bureau of Mines Twin Cities Research Center (TCRC) has evolved from a purely mechanical approach, specifically to reduce dust or frictional methane ignitions, into an understanding of the complexity of the cutting system relationships. Achieving an understanding of these relationships requires a wide variety of testing techniques and equipment. Laboratory facilities and the associated equipment exist for shallow to deep cutting in both coal and coal-inclusive rock with any desired bit type. Research efforts with this equipment are providing insight for significant advances to help solve the problems of pneumoconiosis and frictional ignition. This effort will ultimately affect both respirable dust and methane ignitions at the face through better bit design and will increase the salable percent of run-of-mine (ROM) coal processed. It will also affect the design of rotary-drum cutting continuous mining machines (CMM) and longwall machines. This report describes the main features of the coal cutting research facilities at TCRC.

Jan 1, 1983

By Jon C. Volkwein

The U.S. Bureau of Mines investigated a method of using inert gas to prevent the formation of explosive gas mixtures in auger highwall mining of coal. A combination of gasoline and diesel engine exhaust gases was introduced into the auger drill hole using a short section of pipe located at the collar. Gas samples were taken and analyzed on-site with infrared detectors for oxygen, carbon dioxide, methane, and carbon monoxide. Evacuated bottle samples were also taken and analyzed by gas chromatography in the laboratory. These gas results were analyzed for explosibility. Coal samples from various depths were used to obtain the gas content of the coal using the modified direct method. Personal expo- sure to carbon monoxide was also monitored. The highest methane level observed was 9.55%. The levels of inert gas (carbon dioxide and nitrogen) were sufficiently high to prevent any ignition of the methane. Results showed that for all conditions during mining, gas concentrations were nonexplosive. The gas content of the coal was about 0.30 cm3/g. The maximum personal time-weighted average Sample for carbon monoxide was 20 ppm. This system provides a safe, inexpensive, simple method for preventing explosions during auger mining.

Jan 1, 2010

By Lloyd A. Morley, Robert Stefanko

Before going directly to the analysis, it would be good to summar¬ize explosion-proof container approval methods. Both Magison (52) and Short (84) state that in general practice, the systems are certified for: 1. a rugged enclosure able to withstand an internal explosion but not allow explosively hot gases to escape, and 2. maximum surface temperature, with equipment operating inside, that will not ignite the surrounding atmosphere. Also, testing insures that any material in contact with the container surface will not be ignited by a hot spot. Associated with the first practice, the enclosures are inspected for: 1. a safe flange gap width, 2. a pressure increase during ignition, and 3. an hydrostatic pressure withstand level. The hydrostatic pressure level is almost always determined by a meas¬ured ignition-pressure test and is usually applied to prove the mechan¬ical design to some safety factor. Consequently, explosion-proof enclosure testing includes temper¬ature, permissible flame gap, and pressure. Specifications and prev¬ious research also can be similarly separated even though some interre¬lation exists between the flame gap size and internal enclosure pressure during an explosion. The Schedule 2G Sections applicable to these subjects are: 1. 18.2 Definitions; 2. 18.6 Applications;

Jan 1, 1974

By Steven J. Schatzel

Gas drainage through surface bore-holes has been the conventional means of methane control for U.S. longwall gobs. However, these vertical boreholes are becoming so costly, and the surface rights so difficult to obtain, that the Bureau of Mines is developing underground gob gas drainage as an alternate means of methane control for U.S. longwalls. Holes are drilled into the roof over the panel and on retreating longwalls, towards the working face from a location inby the face. As the longwall retreats, an increasing portion of the hole intercepts the fracture system over the caved gob. A surface exhauster maintains a vacuum on a pipeline parelleling the panel and draws the methane mixture out of the mine. Auxiliary systems of gob gas drain-age during longwall mining will be essential for an increasing number of coal mines. Deep and gassy mines often find ventilation insufficient for adequate dilution of methane in bleeder entries. Although this cross-measure method of degasification has been used successfully in Europe, some of the European techniques cannot be directly applied to U.S. mines. This is the first study of its kind in this country.

Jan 1, 1982