Search Documents

To develop a business case that promotes adoption of noise controls by reducing barriers to industry acceptance and enhancing drivers that foster their implementation. Background Over 75% of the U.S. mining workforce is exposed to hazardous noise, putting them at risk of noise-induced hearing loss (NIHL). Consequently, coal miners suffer high rates of hearing impairment that increase to 70%-90% by retirement age. To address the noise problem for coal miners, researchers from the National Institute for Occupational Safety and Health (NIOSH) first determined that the continuous mining machine (CMM) ranked first among machines associated with reported coal noise overexposures. Further studies found that most CMM noise is generated by three component systems on the machine: dust collection, cutting, and conveying. Of these systems, the on-board chain conveyor was found to be a dominant noise source. Noise generated by the conveying system was addressed through the development of a urethane-coated flight bar chain. The coated chain, shown in Figure 1, has demonstrated an 8-hour time-weighted average (TWA) reduction of operator exposure by 3 dB(A). It has since been accepted by the Mine Safety and Health Administration (MSHA) as a "technologically achievable" noise control for CMM operators who are exposed to noise that exceeds the MSHA permissible exposure level. Having demonstrated the noise reduction performance of the coated chain, NIOSH has assembled information into a business case that can be used by operations considering adopting the chain at their worksite.

Dec 1, 2009

By Margaret R. Egan

The Bureau of Mines experimentally burned Pittsburgh Seam coal and other combustible materials found in mines in order to obtain a better knowledge of their emission products. These experiments were conducted in the Bureau's intermediate-scale fire tunnel, which simulates environ-mental conditions in underground mines. Smoke characteristics, gas concentrations, mass loss, and ventilation were measured. From these values, heat-release rates, particle sizes, obscuration rates, combustion yields, and production constants were calculated. This information was sought as part of a comprehensive study of combustible materials that will ultimately advance the design of more efficient fire detection and suppression systems. The coal combustion measurements presented in this report, together with previous analyses of wood and transformer fluid fires form a data base by which future studies of other mine combustibles can be compared.

Jan 1, 1987

By J. E. Chilton

Underground miners may be exposed to hazardous quantities of toxic gases, such as carbon monoxide (CO), generated from mine fires or explosions. Every underground miner is required to carry a filter self-rescuer (FSR), which when operated will remove CO from the miner's breathing air. In addition, every underground miner must have a self-contained self-rescuer (SCSR) near the worksite that will supply breathing oxygen. In many situations, miners do not know when to don either rescuer since they do not know if there is a fire in the mine, nor do they carry instrumentation necessary for the detection of the toxic, colorless, and odorless fire product CO. If each miner carried a personal CO alarm, which would respond to high concentrations of CO, the miner would then be alerted when to don either the FSR or SCSR and exit the mine. A prototype personal miner's CO alarm called PEMCOAL was developed by the U.S. Bureau of Mines. The PEMCOAL unit is small enough to be carried on a miner's belt, has a flash lamp visual alarm, requires no calibration for use, and uses a chemical sensor that changes color by reaction with trace quantities of CO. The chemical sensor was tested at concentrations of CO from 10 to 1,000 ppm, at temperatures from 5° to 40° C, and with several potential mine gas interferents. The PEMCOAL alarm times were sufficiently fast to warn miners before they are exposed to hazardous quantities of CO.

Jan 1, 1989

By A. L. Engel

In recent investigations of chloride Volatilization of gold at the Reno Station, it was found that the addition of small amounts of copper and NaCl to the charge brought about improved volatilization of the gold. The investigations described in this report were concerned with the recovery, in an aqueous medium, of fumes from chloride volatilization of gold. It was attempted to discover a suitable aqueous medium that would permit absorption, solution, or precipitation of all the volatilized gold immediately upon contact with the medium. A simple laboratory apparatus was employed to produce fumes by volatilization. To this furnace was attached an absorption train consisting of a series of chambers containing the aqueous medium, through which the fumes were drawn by suction. A satisfactory synthetic ore that contained metallic, gold in a quartz-matrix was made and utilized, enough. gold being present in a' small amount of material to permit an accurate, metallurgical balance of the volatized values' to be obtained in all the experiments.

Jan 1, 1949

By Sidney Katell

The reaction of coal, oil, or natural gas with air and oxygen and/or steam yields a gas containing varying amounts of impurities. Depending on the raw material and the end use of the product, these impurities include solids, such as dust or slag, and gases, such as hydrogen sulfide, carbon dioxide, and nitrogen. Considerable effort has been expended in developing and operating purification systems, and the literature is replete with equipment data and operating results. The research problems, the design, and the operation of the various systems have been the subjects of patent applications, journal articles, and textbooks.

Jan 1, 1959

By James P. Bennett

The Bureau of Mines is investigating the acid resistance of ceramic materials to identify construction materials for emerging technology in chemical and metallurgical processes. Eight commercial ceramic materials, were evaluated: two red shale, two fireclay, one silicon carbide, one silica, one carbon, and one high-alumina. Samples were exposed to 10 wt pct H2S04 at 50° C and 10, 30, 50, 70, and 90 wt pct H2S04 at 90° C for time periods of 110 days. Statistically significant changes in cold crushing strength were observed in the silicon carbide and car-bon materials. Weight changes and the leach rate of Al, Ca. Fe. K, Mg, Na. Si, and Ti were also monitored. The most severe corrosion conditions were at 90° C and 30 to 50 wt pct H2S04 for the acidproof and at 10 wt pct H2S04 for the acid-resistant materials. The silica and the high-alumina materials were the most acid-resistant, followed by the higher density red shale and fireclay.

Jan 1, 1986

By George H. Holmes

This paper is one of a series being prepared by the Minerals Division of the Bureau of Mines on mining and milling methods and practices at various mines in the United States. It describes such methods at the Caselton mine of the Combined Metals Reduction Co. The Caselton mine and mill are in secs. 28 and 29, T. 1 N., R. 67 E., M. D. B. & M., Lincoln County, Nev., about 10 miles by paved highway south- west of Pioche, Nev. (fig. 1). the history of the district and company This circular summarizos operations, describes physical features, labor and living conditions, the geology, ore deposits, and the ore. Prospecting and exploration methods are outlined, and shaft sinking, drifting and crosscutting, and raising are covered under development methods. In the soction on mining mothods, stoping and slushing are discussed, following which are descriptions of underground transportation, hoisting, ventilation, drainage and sampling, and surveying. The surface and crushing plants are described, and milling practices are presented in dotail with explanation of the filter plant and assay office. Safoty practices and the company organization are described in the concluding sections of the circular.

Nov 1, 1950

By A. E. Sands

The Bureau of Mines, S. Department of the Interior) at, its Morgantown., W. Va., station, operating under a cooperative agreement with West Virginia University, is conducting research and development work on the problem of producing synthesis gas from coal. An important part of this work is the study of the gas purification necessary to meet the rigorous standards required to render the gas suitable for use in the Fischer-Tropsch synthesis of liquid fuels. One of the most detrimental impurities is sulfur in all forms, the maximum amount that can be tolerated being one-tenth of a grain per hundred cubic feet. Concentrations as low as this require the use of precise analytical methods to evaluate the performance of processes used for removing sulfur. At the same time the analytical methods should be rapid in order to reveal the failure of purification before damage to the expensive synthesis catalyst results. Although sulfur in unpurified gas is generally present as hydrogen sulfide and as organic sulfur compounds, the latter may be converted to hydrogen sulfide for analytical purposes. Thus a suitable method for the determination of traces of hydrogen sulfide may also be used for the determination of organic sulfur.

Jan 1, 1949

By T. E. Ackman

Scale inhibitors and slow-release polymers were tested by the Bureau of Mines at mine drainage treatment facilities. The scale inhibitors were investigated to determine their effectiveness in controlling gypsum (CaSO4) scale; the polymers were investigated to determine their effectiveness for increasing settling rates of suspended iron hydroxide. Two types of scale inhibitors were tested at a site having a severe CaSO4 scaling problem. Both proved to be effective in controlling scale formation; in addition, one caused the dissolution of CaSO4 deposits. Slow-release polymers were tested at three mine drainage treatment facilities. These gelatinous polymeric flocculants were found to be convenient and easy to use, but only effective when pH could be controlled.

Jan 1, 1984

By R. J. Heemstra

A method was developed for calibrating photographic emulsions and retrieving working curves for emission spectrography. The values obtained from a digital readout or a recorder chart of a comparator-microphotometer are converted to light intensity values using an emulsion characteristic curve derived from a quartic polynomial preliminary curve. The characteristic curve, consisting of Seidel transform versus the logarithm of intensity, is split into two cubic polynomials at the zero value of the transform, resulting in eight emulsion calibration coefficients. These methods allow use of the calibration curves even at very small and very high intensities, thus extending the range of analysis. Use of a small computer allows rapid calculations. A computer program was written to formulate, code, and file each working curve along with its statistical error. Proper coding of the input data permits the direct printout of the concentration of the elements under investigation.

Jan 1, 1970

By D. E. Wolfson

This report describes the carbonizing properties of the principal coal beds of Allegheny County, Pa., which rank low in the high-volatile A bituminous classification. Seven coal samples from 3 coal beds were selected for study, as follows: 2 each from the Redstone and Pittsburgh beds and 3 from the Upper Freeport bed. Selection was based on estimated reserves. The samples of Upper Freeport and Pittsburgh coals were satisfactory chemically for producing metallurgical coke. The ash contents of the samples of Redstone coal were moderately high. One of the samples of Redstone coal was high in sulfur content, and it would be difficult to upgrade to meet present metallurgical standards.

Jan 1, 1959

By C. L. Klingman

The Bureau of Mines tested eight commercially available, activated charcoals experimentally to compare the following characteristics: capacity for adsorption of nitrogen at 77° K and 170 atmospheres' pressure, surface area, carbon tetrachloride adsorption capacity, hardness, and density. The nitrogen adsorption test was devised to simulate plant conditions occurring in the final step of purification in Bureau helium faciliti.es. The remaining tests were patterned after empirical acceptance tests that are widely used throughout the adsorbent industry. Surface area and carbon tetrachloride adsorption correlated well with nitrogen adsorption. The samples with low density generally had better adsorption qualities than those of higher density. The carbon tetrachloride test appeared to be the most practical for selecting a charcoal to be purchased, but an attrition, or hardness test should also be run to be sure the charcoal will not crumble in use.

Jan 1, 1966

By H. B. Brunot

The United States Bureau of Mines under provisions of Schedule 2C4 issues approvals covering complete operating units such as loading machines, room hoists, and storage-battery locomotives. Certain manufacturers design and build entire machines. Other manufacturers purchase a part or all of the electrical accessories from manufacturers of electrical equipment and make up permissible units by assembling them. Before the assembler purchases electrical accessories for use in such contemplated units he may require certain information from the accessory manufacturer as to whether the particular accessories are suitable for assembly in his proposed permissible outfit. To aid accessory manufacturers in marketing their product, a provision was incorporated in Schedule 20 whereby tests might be made on individual accessories and reports rendered as to the suitability of a given accessory for use in permissible assemblies.

Jan 1, 1935

By A. L. Engel

[This report describes preliminary tests of samples from six deposits of oxidized copper ores .in Nevada. The tests for the most part were confined to laboratory-scale acid leaching to extract the copper.'The exceptions consisted of flotation tests to demons' ate the possibilities of treating the ore by that method. The samples tested were representative of oxidized copper ores from six counties in all parts of Nevada. The results obtained by the preliminary tests described were indicative of the extractions of copper to be expected, In the five leaching experiments, the approximate consumption of acid was also indicated.]

Jan 1, 1953

By Irving Hartmann, John Nagy, Donald Mitchell

"SUMMARY AND CONCLUSIONThe test data indicate that water infusion of the Pittsburgh coal seam does not reduce the amount of fine dust produced during mining operations to the extent reported elsewhere. Wide variations in the amounts of dust collected in the air current were noted in duplicate samples and repetitive tests. Changes in depth and location of the infusion holes and amount of water injected and addition of a wetting agent to the water had little effect on the amount of dust liberated.Water was forced readily into the coal. Some water flowed out along the cleats, but an appreciable amount remained in the seam. Little or no water pene¬trated the coal seam above the upper infusion holes.The average dust concentration (with and without infusion) in the return air, 40 feet outby the working face, was 25 million particles per cubic foot during undercutting, 20 million during drilling, 75 million during shot firing, and 20 million during hand loading. At the working face the average concentration was 3 to 6 times higher. The concentrations were measured at an airflow of 1,600 cubic feet per minute (c.f.m.) at the face.On the basis of this short investigation, no final conclusions can be made on the effectiveness of water infusion in reducing the amount of fine dust liberated during mining in the Pittsburgh coal seam. However, the data indicate that dust reduction resulting from infusion would be small.INTRODUCTIONThe production of fine coal dust is an inherent part of nearly every phase of mining. The use of large, high-speed continuous-mining machines and other mechanical equipment has increased dust production. In addition, in coal seams that have been subjected to high pressures for a long period, and particularly in dry and friable seams, some very fine dust is in the seam before mining. Much effort has been devoted to allaying and collecting at its source the fine coal dust released during mining. One of the comparatively recent techniques that has been developed for this purpose is infusion of water or other liquids into the coal seam. This method consists of injecting water under pressure into a coal seam to neutralize the fine dust released during mining. The water generally is introduced through bore holes in the face before undercutting."

Jul 1, 1957

By W. M. Weigel

Langley is about nine miles north of Augusta, Georgia., on the Sou them :l;.ilv1ay. According to the South Carolina. Geological Survey, tr.e district is known a.s tr. Horse Creek and Town Creek sub-areas of the Aileen or Savannah River Area f the South Ciil.Z'olina Coastal Plains. The geology and origin of the clays 3l"e Jscribea in a bulletin of the South Carolina Geological Survey (Series 4, Bull, l; "A Preliminary Report on Cl.:.ws of South Carolina.-), According to this report, i.he clays are sedimentary kaolins, in the Mid.dendor! and Hamburg series of the Cretaceous Age.

Aug 1, 1922

By G. H. Keith

A vanadium-base alloy consisting of the following elements in weight-percent--molybdenum, 20; titanium, 10; carbon, 0.1; silicon, 0.5; and yttrium, 0.5--had exceptionally high strength at temperatures up to 1,200° C. This alloy was capable of fabrication to sheet of ~ 1 mm thickness by a combination of hot swaging and hot and warm rolling. In the warm-rolled condition at ambient temperature, its ultimate tensile strength was 1,205 MN/m2. The strength at 1,200° C was 150 MN/m2. Within the temperature range of 25° to 1,200° C, the ductility of the alloy as measured by elongation increased from 4 to >90 percent. Strengthening was achieved by both solid-solution and dispersed-phase mechanisms. Alloys of 20 percent molybdenum and 10 percent titanium were stronger than the other molybdenum-titanium alloy compositions tested. Strength was increased 15 percent in the temperature range of 25° to 800° C, with no accompanying loss in ductility, by the addition of 0.5 percent silicon. Workability was improved by additions of 0.25 and 0.5 percent yttrium.

Jan 1, 1970

By Jacqueline A. McClaskey

The U.S. Bureau of Mines (USBM) Information and Analysis Directorate collects worldwide data on virtually every commercially important non fuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. The USBM's data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 329), which placed the collection of mineral statistics on an annual basis. The most recent authority for the USBM survey activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress). This act strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1993

By J. G. Donaldson

Binary alloys of molybdenum and tungsten were prepared by the Bureau of Mines in laboratory-scale experiments by hydrogen reduction of their vaporized hexafluorides. Near-optimum deposition parameters were determined, and the nature of the deposited alloys was investigated. Dense, homogeneous alloys were codeposited between 650° and 750° C with a reduction efficiency of more than 75 percent. The alloy composition was uniform when the hydrogen ratio in the gas feed mixture did not exceed 3 times the stoichiometric requirement. Regulating the proportions of the metal hexafluorides in the gas feed provided a large degree of control over the composition of the deposit. Hardness of the deposits varied directly with the proportion of excess hydro,,,, in the gas feed and with the weight-percent of tungsten in the alloy. Hardness was not affected by deposition temperature over the range 650° to 750° C for specimens of similar composition. Extreme brittleness and unsuitable physical shapes of the alloys prevented tensile strength measurements.

Jan 1, 1966

By A. C. Richardson

[During the past two and a half sears the U. S. Bureau of Mines and the University of Alabama, with the cooperation of the different coal operators, have been making an extensive studs of coal preparation in the State of Alabama. Considerable time has been devoted to the studs of the washing characteristics of the Mars Lee bed and the various methods used In preparing from it a low-ash coal suitable for the manufacture of metallurgical coke. One of the phases of this problem is the utilization of middlings products from the washing plants. This paper gives the results of treating jig middlings on a coal-washing table at the Bureau of Mines laboratory at Tuscaloosa, Ala. The sample used was secured from the Sayreton washery of the Republic Steel Corporation, Sayreton, Ala. WASHERY PRACTICE The Mary Lee bed is very bony, and operators find it difficult to produce from this bed a washed coal much under 10 per cent ash. Experience has shown that in the preparation of a coking coal from the Mary Lee bed it is best to use a process which permits the recovery of a middlings product. Middlings are desirable because separation according to specific gravity is never perfect, and a middlings product makes possible a low ash in the primary warned coal without excessive losses of combustible in the refuse. The general washery practice on the Mary Lee bed is to crush the run-of-mine coal through some maximum screen size and wash it upon some one type of jig without re-treatment of any of the products made. The maximum size treated varies from 3 inch to J inch. The middlings product from multiple-cell jigs is usually termed "boiler fuel" and when possible is utilized as such. At present the production of boiler fuel is often in excess of power requirements, and the surplus, due to its high ash content, becomes waste.]

Jan 1, 1931