Search Documents

By Daniel E. Sullivan

The recession of 1974 continued into 1975. Real gross national product (GNP), measured in 1972 dollars, declined significantly in the first quarter of 1975 but rose slightly in the second and increased sharply in the third quarter. Unemployment peaked during the second quarter and then declined slowly for the balance of the year. The inflation rate declined owing to reduced demand and smaller-than-1974 increases in energy and food prices early in the year. Recovery was clearly evident by yearend, though un-employment and inflation remained at high levels. Total output as measured by the GNP in current dollars rose 6.5% in 1975. Real GNP declined 2.0%, and inflation, as measured by the implicit price deflator, increased 8.7%. Real gross private domestic investment for residential structures declined 18.1% in 1975, which was a smaller rate of decrease than the 27% decline in 1974. Real State and local Government purchases increased 2.4%, and real personal consumption expenditures for services rose 1. 7 %. The Federal Reserve Board (FRB) index of industrial production declined 9.7%.

Jan 1, 1977

By A. J. Barry

A practical method has been developed and field tested which provides an estimate of the bearing capacity of mine roof and floor. The relationship between penetration of the strata and imposed loads is determined by in situ tests. Information of this type is needed to determine the maximum allowable pressure that may be applied by self-advancing supports on roof and floor of a longwall face without causing a punching type of failure.

Jan 1, 1970

By C. G. Maier

The present trend of chemicometallurgical research toward widespread and inclusive use of thermodynamic methods requires the inclusion of available data of this sort in any comprehensive metallurgical report . Such data for manganese are far from adequate for the full utilization of these methods . Even if our knowledge of these properties is weak , the collection of available figures is nevertheless well worth while , especially if their utilization in an approximate way may show inherent possibilities of application . No less important is the necessity for discovering the vital gaps in the existing information , to serve as a basis for further pertinent study . The utility of the thermodynamic methods of Lewis and Randall ( 234 ) 3 has become increasingly evident to metallurgists . It is true that at present no better approach to the general , fundamental problems of chemical metallurgy is available than close adherence to these methods . The effort is here made to collect and correlate , as far as possible , significant quantitative thermodynamic data on manganese and its metallurgically important compounds . There are considered here only the intrinsic properties of pure materials . The order maintained as far as possible will be as follows :

May 1, 1934

By H. D. Hess

This report describes in detail a unique occurrence of fersmite, (Ca, Ce, Na) (Cb, Ti, Fe, Al)2 (0, OH, F)6, which occurs as small anhedral inclusions and intergrowths with a tantalum-free columbite found in the metamorphic complexes of Ravalli County, Mont. Chemical and crystallographic data along with the physical and optical properties agree in general with those given in the original description of fersmite from the Ural Mountains of Russia. X-ray diffraction data not given in the original description and more specific optical data have been determined. The Montana fersmite, now established as the second occurrence of this rare calcium-columbate mineral, was discovered during a routine Bureau of Mines mineralogical examination of a prospector's sample.

Jan 1, 1960

By C. J. Walker, Ray V. Huff

The feasibility of inert - gas cushions in underground gas storages was studied by the Bureau of Mines in accordance with a continuing program of cooperative research between the natural gas industry -- through the American Gas Association . As mixing of the inert - gas cushion with the stored natural gas is undesirable , the various mechanisms tending to bring about such mixing were the subjects of both theoretical and experimental studies . These studies indicated the practicability of such cushions is dependent upon both reservoir and operating conditions . Equations and tables of illustrative data relating the various reservoir and operating conditions to the expected time required for undesired mixing to occur in ideal reservoirs are presented . This information permits estimating the relationship of such factors in actual storage operations .

Jan 1, 1964

By Eldon K. Stanek

The material presented in this chapter is a review of the work done during the period from June 23, 1972 to June 22, 1973 which was reported in detail in the first annual report for Grant No. 60122088 which was submitted on June 29, 1973. This report has appeared in the National Technical Information Service as bulletin number PB230 972/AS. 1.2 ANALYTICAL PREDICTIONS OF INDUCED VOLTAGES AND CURRENTS The basic building block in this analytical work is the development of an equivalent circuit. The equivalent circuit for the cable depends on all of the distributed parameters of the cable, although the series inductance and resistance are of primary importance. The cable resistances are generally available from handbooks or from cable manufacturers. On the other hand, the cable inductances are not usually available from either handbooks or the manufacturer's published data. Thus, it is useful to present the results of the derivation of the inductance matrix and a few intermediate steps.

Jan 1, 1975

By J. B. Zink, M. J. Peterson

A semiquantitative spectrochemical method was developed and applied to the analysis of ash of U.S. coals . A low- temperature ashing procedure was used to minimize the loss of volatile elements . The analytical procedure provides for the estimation of 68 elements including major , minor , and trace constituents . Standards for the trace elements were prepared in a synthetic base mixture that approximates the average composition of U.S. coal ashes . Excitation was achieved with a d- c arc , spectra were recorded photographically , and interpretation was made by visual comparison of spectra of unknowns with spectra of graded standards series . Thirty- six trace elements were found in the analysis of 900 samples . Details of the procedure are presented , including sample and standards preparation , excitation and exposure conditions , spectral lines used , and approximate limits of detectability .

Jan 1, 1964

By G. L. Oldright

In the previous study that has been made by the authors on smelting in the lead blast furnace, the furnace examined was one that operated under conditions that have been considered as more or less normal up to the present time. That is although the furnace had in its charge a large portion of sinter, it also handled considerable quantities of naturally oxidized direct-smelting ore. Other ingredients, such as the limestone, were also added as fairly coarse material. The charges contained only about 24 per cent of lead. Until the changes incident to modern flotation began to take effect, many lead plants doing semicustom smelting in districts where competition was keen and much of the bonanza ore was exhausted were faced with the difficulty of obtaining enough lead to get a sufficient "lead fall" in the blast furnaces to clean the slag thoroughly and to separate it from the lead. A charge containing 24 per cent of lead would have been considered a very rich one by such smelters.

Jan 1, 1931

By K. B. Rojiani

Surface mining activities disturb large tracts of land resulting in the potential for greatly increased downstream sediment loads. The Surface Mining Control and Reclamation Act of 1977 places increased emphasis on the protection of the environment from the adverse effects of surface mining operations. Surface mining activities must be planned to minimize disturbance to the hydrologic balance, erosion and sediment contributions to receiving streams. Sediment ponds must provide a sediment storage volume equal to the accumulated sediment volume from the drainage area as determined by the Universal Soil Loss Equation (USLE) or other empirical methods established by the regulatory authority. It has thus become extremely important for the mining industry to secure more accurate estimates of potential erosion losses and sediment yield. Accurate estimates of sediment yield are required for the planning, design and successful operation of sediment control systems such as detention ponds and other alternative control structures and for evaluating the effectiveness of land management practices. The principal soil loss prediction procedure available for use is the LISLE. The USLE procedure is inadequate for use in predicting soil loss from surface mine regions for a number of reasons. These include: 1. The USLE was developed to estimate average average annual loss from agricultural soils. It cannot predict accurately soil loss for specific storm events. In surface mine regions a major portion of the soil loss occurs during the initial six months to one year of active mining. Accurate estimates of soil loss over short periods are thus required for the design of control structures. 2. The slope length and gradient factors used in the USLE were obtained from data or cropland having slopes ranging

Jan 1, 1983

By G. Richards Gwinn

Vermiculites are secondary minerals formed by the: alteration of biotite and philogopite mica and are associated with basic rocks such as dunites, serpentines, and pyroxenites. Vermiculite was first described by T. H. Webb in 1824. It remained a mineralogical curiosity until 1913, when the first commercial deposit was discovered in the Turrett mining district of Colorado. Expanded or exfoliated vermiculite was first marketed in 1915 from a deposit in this district 5 miles southeast of Hecla, Colo. This activity was brief, but successful and continuous commercial development began in 1921 in Montana. 'Deposits in other States have been found and developed, but Montana is by far the largest producer. Vermiculite has also been found in South Africa, Western

Jan 1, 1944

By Clayton A. Landsidle

There has been little change in timbering methods in anthracite mines for 75 years, and technical information on strata control is almost wholly lacking. In order to assist the industry to establish technical data, the Bureau of Mines and a Northern field operator are cooperating in underground experiments, the first phase of which has been to investigate pneumatic packing. The four principal methods of packing in mining are hydraulic, pneumatic, mechanical, and hand. The hydraulic pa caring system is believed to have originated at Shenanodah, Pa., in 1864,4/ to prevent destruction of a church by surface subsidence after underground coal mining. This method was used again in 1884 to arrest an underground fire at Buck Ridge colliery, near Shamokin, Pa. In 1901 hydraulic packing was introduced to Europe in Upper Silesia, where it gained in popularity owing to the availability of large quantities of sand suitable for flushing .5/ Hydraulic packing has a number of disadvantages. Chief among these are the softening effect of large quantities of water on the mine floor conducive to heaving action; drainage and punning costs; and the inability to fill roof cavities completely in flat beds.

Jan 1, 1953

By George A. Bell

This paper reviewing the leaching practice of the New Cornelia mines of the Calumet & Arizona Mining Co. at Ajo, Ariz., is the first of a series being prepared by the Bureau of Mines on leaching methods and costs in the various mining districts. ACKNOWLEDGMENTS The author acknowledges the assistance of T. G. Chapman, consulting engineer, and E. D. Gardner, supervising engineer of the Southwest Experiment Station, Bureau of Mines, Tucson, Ariz.

Jan 1, 1930

By A. U. Miller

Definite progress has been made in accident prevention in Illinois during the past few years; the State Department of Mines and Minerals is receiving excellent cooperation from coal companies and employees, the companies are making greater effort to maintain their mines in good condi- tion, and the employees are eliminating more unsafe practices. As a result, some coal companies have made commendable safety records that prove that coal can be mined with a comparatively low accident rate. However, there is need for further improvement, as the accident rate of the State as a whole is much higher than it should be. During the 55-year period 1882-1936, in- clusive, reports of the State Department of Mines and Minerals show a total of 7,005 (an average of 127.36 per year) men killed in and around the coal mines. Of this number, 6,425 (91.7 percent) were killed underground, 346 (4.9 percent) in the shaft, and 234 (3.3 percent) on the surface. Of the fatalities underground, 3,300 (51.3 percent) were killed by falls of roof, sides, or face coal, 1,167 (18.1 percent) by haulage, 639 (9.9 percent) by handling explosives, 579 (9 percent) by explosions, 151 (2.3 percent) by electricity, and 589 (9.1 percent) by other means. Of the fatalities in the shaft, 171 men (46.5 percent) were killed by falling down the shaft, 14 (41.6 percent) by the cage, and 31 (8.9 percent) otherwise. On the surface, 113 (48.2 percent) of the fatalities were due to railroad cars, 51 (21.7 percent) to machinery, and 70 (29.9 percent) to other causes. The fact that 7,005 lives (an average of 127.36 per year) were lost during 1882-1936 is sufficient evidence that in the past too little interest has been taken in safety by either the management or workers. A realization of this deplorable loss of life should act as an incentive to the industry to make greater effort to prevent accidents in the future. After an accident occurs, the facts pertaining to it become history, and anything that may be done afterward cannot change in any way the damage that has already been done, such as loss of life, personal injury, and destruction of property. The main benefit that can be derived from an acci- dent is that suitable procedure may be adopted and some lesson may be learned to aid in preventing a similar accident in the future. All accidents, par- ticularly serious ones, therefore should be investigated and an effort made

Apr 1, 1938

By L. C. IlsLey

Cooperation between the United States Bureau of Mines and the Safety in Mines Research Board of Great Britain, continuous since 1924, has made possible this and other papers on safety subjects. Grateful acknowledgment is made to representatives of the Safety in Mines Research Board of the Mines Department for their assistance in arranging visits to several mine safety stations, and to F. R. Wynne, Deputy Chief Inspector of Mines, Great Britain, for arranging visits to mines in Great Britain, Belgium, Germany, and France. During the summer of 1927 the writer had the privilege of visiting the mine safety testing stations in Great Britain, Belgium, Germany, and France, in the order named. All of these countries have large coal mines, many of which are rated as gassy. Therefore, when installation of electrical equipment is contemplated, each of these countries is confronted with the same safety problem as is the United States - the development of electrical equipment that will not ignite gassy mine atmospheres which might, through neglect or accident surround the equipment. The means used by these countries in safeguarding gassy mines should therefore be of general interest to safety engineers of American coal mines, and it is proposed to give a brief survey for each of the four countries mentioned. This paper presents the second of these surveys, which covers conditions in Belgium.

Jan 1, 1929

By E. G. Davis

Large-scale ultrafine grinding tests of a coarse kaolin were made using the Bureau of Mines developed attrition grinding process in continuous open-and closed-circuit systems. A 20-inch diameter attrition grinder, designed and constructed at the Tuscaloosa Laboratory, was used. Studies included single- and multiple-stage open-circuit grinding, and also continuous grinding tests in closed-circuit with a 6-inch-diameter solid bowl centrifuge. Clay feed, containing 9.0 percent minus-2-micrometer esd, was used at fates up to 840 pounds per hour. Multistage grinding tests gave better results than single-stage treatment when equivalent clay feed rates were used. Closed-circuit grinding tests yielded ground products containing slightly more minus-2-micrometer-esd clay than the open-circuit grinding when using the same clay feed. Energy consumption was lower in closed-circuit grinding than in batch or open-circuit grinding. A modified two-stage closed-circuit grinding system gave the best grade of product and amount of minus -2-micrometer-esd clay produced per pound of clay feed. The ground product from this test contained 88.5 percent minus-2-micrometer-esd material and electrical energy consumption was 327 kilowatt-hours per ton of minus-2-micrometer-esd material produced.

Jan 1, 1973

By R. E. Brewer

Published investigations show that many different chemical reagents have been used in determining the constitution of coals , but only a few studies have been applied directly in evaluating the effects of such reagents on the carbonization products of coal , Most of the treatments have been so drastic that any permissible conclusions that may be drawn are inferential in respect to any favorable effects on the yields and composition of the usual carbonization products .

Sep 1, 1943

By N. E. Hanna

The current Bureau of Mines active list of permissible explosives includes 124 brands. Thirteen are gelatinous and the rest are the more commonly used granular ammonium nitrate type. The list of permissible blasting devices comprises five Cardox models.

Jan 1, 1965

By N. E. Hanna

The current Bureau of Mines active list of permissible explosives includes 124 brands. Thirteen are gelatinous and the rest are the more commonly used granular ammonium nitrate type. The list of permissible blasting devices comprises five Cardox models.

Jan 1, 1965

By Edward L. McHugh

The appraisal of mineral resources of the Challis National Forest, Idaho, by the U.S. Bureau of Mines, was made so that the mineral resources of the forest could be appropriately considered in land use planning. Information from this study is intended to help the U.S. Forest Service to incorporate mineral resource data into forest plans. The study was done in conjunction with the U.S. Geological Survey, which released a companion report on the geology and mineral potential of the Challis National Forest in 1989. Mineral development activity in and under the Challis National Forest has been of great economic significance to Idaho and the United States. Since the 1960's, mines within the forest have produced mineral commodities worth more than $590 million A current (1989) commodity prices. Identified mineral resources have a gross value of about $2 billion at current prices, including 8 strategic or critical minerals. The U.S. Bureau of Mines study identified and described 723 active and inactive mineral properties within the forest. Mineral properties with identified resources were evaluated to determine their economic significance, and an assessment was made of the feasibility of mineral development. Of the 2,516,191 acres in the Challis National Forest, about 390,000 acres were classified as having mining development interest commercially important mineral production, mainly of molybdenum, gold, and silver from the Challis National Forest is likely for the foreseeable future.

Jan 1, 1991

By Harry H. Ku

In December 1975, a report entitled "An Evaluation of the Accuracy of the Coal Mine Dust Sampling Program Administered by the Department of Interior" [1] was prepared by the Analytical Chemistry Division of the National Bureau of Standards (NBS), in response to a request by Senator Harrison A. Williams. Chairman, Committee on Labor and Public Welfare. The report attempted to evaluate the adequacy of (1) the personal sampler unit used to measure the coal dust concentration in the mines, (2) the procedures used by the Department of Interior (DOI) to analyze the dust samples obtained from mine operators, and (3) any recent studies made by the Department or private industry concerning the coal dust sampling equipment. Recommendations in the report of NBS included continued research efforts by the appropriate organization to correct the personal sampler deficiencies and to consider the use of area or stationary samplers as a supplement to the personal samplers. Concurrent with the NBS report cited above, the General Accounting Office (GAO) also issued a report in December, 1975 [2], suggesting that improvements are still needed in coal mine dust sampling programs and procedures relating to penalty assessments and collections. Among recommendations made by GAO, the following paragraph specifically called for actions by the agencies involved:

Jan 1, 1979