Search Documents

By T. C. Wesson

The need for elemental-analysis information on coal mine dust for use in health and safety research prompted this study by the Bureau of Mines. Neutron-activation and X-ray fluorescent techniques were used to obtain five-element analysis (silicon, aluminum, iron, calcium, and magnesium) on 444 samples from 68 coal mines in 10 States. From these analyses, the average composition of the dust in coal mines was determined. The contribution of the primary dusting material (limestone dust) to the makeup of coal mines was shown. Regional differences in mine-dust composition were indicated.

Jan 1, 1974

By Donald F. MacDonald

This report aims to discuss, from the viewpoint of the mining geologist, the bearing of topographic and geologic conditions on cer- tain problems that arose in the construction of the Panama Canal. T+ is published by the Bureau of Mines as a contribution to engineer- ing liters ure because it presents information that shows how geology and topography must be considered by the mining engineer in plan- ning excavations and in removing loose material and solid rock in the safest and most efficient manner. The printing of this bulletin has been approved by the governor of the Panama Canal, as it was impracticable for the Panama Canal to give this information to the general public in any of its publications. The "sword cut" of Goethals and his men did not sever the Isth- mian barrier; it merely clove the hills to a depth of 40 feet above sea level. This cut and the great areas of low valleys at both ends of it have been covered with fresh water to the 85-foot level. This high-level lake held by dams at either end, the 85-foot locks, by which ships enter it, and the dredged approaches from the two oceans constitute the Panama Canal. In the preparation of accurate estimates concerning the cost of large excavations information regarding the geologic conditions, as obtained by a study of natural features, is necessary. Drill holes and test pits will furnish supplementary geologic information, but without a gen- eral knowledge of the geologic conditions it will not be possible for the constructing engineer to answer such questions as the following: (1) What rock units will be encountered in the excavation and in what proportion? (2) What will be the cost of drilling each for blasting (3) How far apart and how deep must the drill holes be to efficiently break the rock of each to the proper size-not too fine nor yet too coarse? In this connection jointing, fissuring, bedding, toughness, and other physical characteristics must be considered (4) How steep will the slopes of the excavation stand, and to what extent will they wash and trench on exposure to the atmosphere? (5) What proportion of the material to be excavated is of such physical character that it may be utilized in any other part of the project, such as in concrete construction, road making, wharves, breakwaters, riprap work, etc.

Jan 1, 1915

By Ronald M. Van Noy

A reconnaissance study of kyanite-group mineral deposits in the Northwest has revealed large exploitable reserves of the mullite-forming raw materials in the Woodrat Mountain and Goat Mountain districts of north-central Idaho. Potential coproducts or byproducts are garnet and muscovite mica. The Woodrat Mountain district contains garnet-kyanite-mica schist, which has been traced for 6 miles and may extend farther. Surface samples average 29 percent kyanite and contain up to 15 percent garnet. Inferred reserves of strippable ore with a low waste-to-ore ratio, and containing more than 15 percent kyanite, are more than 3 billion short tons. The Goat Mountain district contains several kyanite-mineral zones. Samples of the richest zones average from 10 to 20 percent kyanite minerals and represent about 200 million short tons of strippable rock. Beneficiation tests indicate that the kyanite minerals and garnet can be concentrated by a combination of gravity, flotation, and electromagnetic methods. Reserves in these deposits are sufficient to satisfy any foreseeable domestic and export demand. However, the freight tariff to reach the nearest major users of kyanite (located in the Midwest) has discouraged development of western kyanite resources. Western demand of a magnitude to support a moderate to large milling operation has not yet been developed. However, there is some foreign market potential. If a garnet byproduct could be prepared and sold for coated abrasive products or as grinding grains, an offset possibly could be gained to a por¬tion of the mining and milling costs for the Pacific Northwest producer. Such byproduct values would offer a means for expanding the geographic market areas as well as the regional market potential.

Jan 1, 1970

By C. A. Geffen-Fowler

This report, sponsored by the Bureau of Mines, presents the results of an examination of the safety of the Blind Shaft Borer (BSB) shaft sinking system and an alternative modified BSB design concept in comparison to conventional shaft sinking technology. Detailed study of the two systems was also performed to identify and recommend design changes for optimum safety conditions. A comparison of the BSB systems with conventional shaft sinking was made on the basis of relative risk levels. Risk incorporates both the frequency and the potential consequence of accidents. A safety evaluation of the component operations of the two BSB systems was performed using a Failure Modes and Effects Analysis (FMEA) methodology. The results of this analysis show generally that both BSS systems are safer than conventional shaft sinking. The potential risk of conventional shaft sinking operations could be reduced by over 30%, on the average, with the use of the original BSB system, and by an average of about 10% with the modified BSB. Design change recommendations to further improve the safety of these systems include a better fire suppression system, improved man haulage systems and more compact hydraulics. An operational safety manual was also developed for the modified BSB system.

Jan 1, 1981

The 53 countries that constituted Africa in 1993 accounted for a significant portion of total world output of a number of mineral commodities. For the continent as a whole, world shares of most commodities showed little change from those of 1992 although most output volumes showed a slight decline. There were no significant production increases, but there were significant decreases of cobalt and copper because of political instability in Zaire and production problems in Zambia, of chromite resulting from cutbacks in South Africa and Zimbabwe, and of phosphate rock owing to a lower output by producers in general. (See tables 1 and 2.) Among the most significant mineral commodities produced in Africa, ranked by portion of world production in 1993, were diamond, cobalt, chromite, gold, phosphate rock, manganese ore, uranium and petroleum. Others of importance in world trade were andalusite, antimony, asbestos, bauxite, coal, copper, fluorspar, lithium minerals, platinum-group metals (PGM), titanium minerals (ilmenite and rutile), vanadium, vermiculite, and zircon. Several of these-chromite cobalt, diamond, and manganese-were not produced in the United States.

Jan 1, 1995

By R. J. Burgess

During World War II the shortage of ore revived interest in eastern iron deposits, among which -!2..c "Ile Massachusetts and Connecticut limonites. The Cheever mine, in the Richmond-Salisbury area of Massachusetts, was formerly a large producer of limonite ere. The Bureau of Mines investigated the lateral and downward extensions of the Cheever ore body, which was mined from about 1850 to 1892, by ap open cut 1,000 feet long and also by underground workings. even holes aggregating 1,723 feet, were drilled by the Bureau during the winter of 1943-44. They comprised three diamond-core drill holes, two churn-drill holes, and two rotary-drill holes. A geophysical survey of the Cheever mine area and adjoining ground was made in conjunction with the drilling program. Although this survey did not locate the limonite ore beds, the data were of considerable assistance in locating the limestone contact which forms the footwall of the ore beds. Drilling disclosed two beds of limonite with a heavy overburden of glacial till.

Jan 1, 1949

The overall objective of this study is to gather operational data from selected surface coal mining systems in the United States, and to assess the potential production and economic capacity of the systems. The study includes: four mines, each using a different mining technique and different equipment. One mine was selected from each of the major coal fields: Midwestern, eastern,, northwestern, and southwestern. The Midwestern Mine is located in the Central Plains and produced 1.45 million tons of raw coal during the study year The Midwestern Mine uses the area mining or box-cut technique. A large in-pit shovel and a bucket wheel excavator are used to remove the overburden. Coal is removed by a loading shovel and transported to the dumping point by large off--highway trucks.

Jan 1, 1975

By E. P. Dowding, J. Schlocker, C. H. Fuchsman, R. R. Lloyd, Mahan. W. M., O. C. Garst, W. T. Rawles

"INTRODUCTION The United States, although the leading consumer of chromite, depends almost entirely on imports for its supply. For instance, the consumption during. 1941 amounted to 714,645 long tons, whereas the domestic chromite production, although the highest since 1918, was 12,731 long tons or only 1.78 percent of the domestic consumption. 9/ Domestic production was tremendously, accelerated,after 1941 by war demands; however, only a small proportion of this domestic product was of sufficient quality to be substituted for the high-grade imported chromite demanded for metallurgical purpose. Chromite is used largely for making ferrochromium, an alloy containing 60 to 70 percent chromium which is used in making alloy steels. Peacetime specification for ferrochromium required that it should contain 68 to 69 percent chromium. These specification were lowered to between 60 and 63 percent, chromium in 1941 to permit the use of lower-grade ores. The specifications for metallurgical chromite, used for making ferrochromium, were established first by the Metals Reserve Company at 48 percent Cr203 and a Cr. Fe. ratio of 3 : 1 but later were lowered to 45 percent Cr203 and a Cr : Fe ratio of 2.5 : 1. The ratio of chromium to iron in chromite is important, because the contained iron enters the alloy in making ferrochromium and, although an ore may contain the required 45 percent Cr203, it may contain too much to be suitable for ferrochromium production. The principal sources of domestic chromite are California, Oregon, Montana, and Alaska minor, small, and widely scattered deposits in another dozen States. Without exception, these deposits are low-grade, require beneficiation to produce a commercial product, and are not competitive with imported high-grade ore in normal times. Nevertheless, these deposits form strategic reserve, which must be utilized in periods of national emergency. Recognizing this fact; the Bureau of Mines for many years has undertaken investigations to develop methods of utilizing domestic chromite ores. The problem has been approached from three angles: (1) Mechanical methods of concentration; (2) beneficiation by chemical or metal¬lurgical methods; and (3) production of metallic chromium by electrolysis of solutions prepared from ore or concentrate."

Feb 1, 1946

By S. P. Sandoval

Previous research by the U.S. Bureau of Mines demonstrated that nonionic surfactants increased the leaching rate of copper in the flask leaching of chalcopyrite with ferric sulfate if sufficient ferric sulfate was present. This research was continued by the Bureau in Part 2 to further explore the application of nonionic surfactants to the dump leaching of chalcopyrite. A polyoxyethylene lauryl ether was selected as the superior nonionic surfactant tested at 25° and 50° C. The addition of the surfactant increased copper leaching by 116 pct at 25° C and 1.0 pct solids and by 61 pct at 50° C and 0.5 pct solids at Fe 3+ concentrations greater than 1 g/L. At 0.1.0 g/L Fe 3+ and below, the addition of the surfactant produced as much as a 35 pct decrease in leaching. Each of the nonionic surfactants studied was found to be heavily adsorbed by a typical chalcopyrite ore, which poses a serious barrier to the application of nonionic surfactants in an actual chalcopyrite dump.

Jan 1, 2010

By Paul J. Guay

This report presents the results of evaluating a longwall mining system specifically designed to extract a very deep web (60 inches or deeper) from a longwall panel. The report includes a productivity and cost analysis comparing the new mining sys-tem with a high capacity conventional longwall operation taking a 30-inch wide web. The analysis shows the new system will increase annual production 44 percent and decrease cost per ton off the face 21 percent. The report also includes conceptual drawings and specifications for a high capacity four-drum shearer and a unique shield type of roof support specifically designed for very wide web operation. The advantages and problems associated with wide web mining are discussed in general and as they relate specifically to the equipment selected for the new mining system. The study concludes by recommending that surface coal loading tests be conducted as the follow-on work.

Jan 1, 1978

By Roger G. Long

This final report reviews installation, maintenance and inspection of mine pager telephone installations. A Technical Handbook was developed and distributed. Certain commercial telephone test equipment was modified and a tone source and switching circuit were developed for use in the testing of mine pager phone systems. Descriptions are included of the modifications to a commercial test set and of a tone source/ switching unit.

Jan 1, 1975

By Earl T. Hayes

[This work represent a continuation of the efforts of the Metallurgical Division of the Bureau of Mines to ascertain and apply knowledge of miner physics to processes metallurgy.]

Jan 1, 1941

By Ronald S. Conti

This U.S. Bureau of Mines (USBM) report describes various fire-fighting resources available to the mining industry and examines the fire preparedness of four western coal mines. Information regarding fire-fighting equipment indicates that an inadequate maintenance program may cause component failure of fire extinguishers, damage to waterhoses is usually a result of improper care, and foam may be a convenient means of conveying water to the fire. Performance data relative to water nozzles (throw distance) and specific practices to improve the state of preparedness in many of these areas are discussed. Studies also indicated that a high-expansion foam plug, will travel down an entry, with a 1% rise in elevation, 207 m (680 ft) before a plywood stopping separating the generator and plug failed. The advance rate of the foam plug decreased when the entry is dry, requiring more foam concentrate and as the foam spread further down the entry. An examination of the mines showed state-of-the-art monitoring systems were common at the minesites. Fire safety was also stressed, including early detection and rapid response of the miners to evacuate the mine. However, the mines placed little emphasis on performance of water nozzles, or personal protective clothing for the underground firefighters.

Jan 1, 1994

By Joseph F. Davies

Along with the humanitarian need for preventing accidents the cost of injuries must be considered. As a means of bringing the facts concerning the prevalence of accidents in mining and their direct cost before the operating officials and others interested in accident prevention in the mining industry, the United. States Bureau of Mines ha as recently made studies and published reports dealing with these subjects in several States 4. This report gives available data on the causes and direct costs of accidents in Virginia coal mines for the 4-year period 1929 to 1932, inclusive. Mounting compensation costs and insurance rates resulting from mine injuries indicate the necessity of measures to decrease the number and severity of accidents. These direct costs, as well as additional losses of an indirect nature, can be eliminated from the cost of production to the extent that accidents are prevented or reduced in severity.

Jan 1, 1934

By Parry. V. F.

"INTRODUCTION Coal is a compressed mass of heterogeneous, macerated, metamorphosed plant remains that have collected in the earth's crust. Probably no two beds of coal have identical properties, and different parts of the same bed may vary considerably when measured by some of the many empirical tests that have been developed to classify or differentiate the properties of coal. Because of this great variability in properties, the commercial processing of coal to produce coke and byproducts has developed largely as an art based on experience, rather than as a science. Much empirical chemical research, however, has been and is being conducted on coal carbonization, and this work is of practical value in obtaining larger yields of gas and byproducts and in the improvement of the physical properties of the coke.Both ultimate and proximate analyses have been used for correlating purposes. 3/ In the United States the proximate analysis is used for the classification of coal according to rank and grade. The proximate analysis can be employed usefully in the coal—carbonization industry because separation of the combustible matter of coal into volatile matter and fixed carbon is, in fact, a small carbonization test conducted on 1 gram of coal heated in a platinum crucible.Small—Scale Laboratory Coking Tests,Many empirical tests have been devised for determining the coking properties and measuring the yield and quality of gas and byproducts obtainable from various coals. These tests, made on samples ranging from 25 grams (about 1 ounce) to 5 kilograms (11 pounds), furnish information that is roughly proportional in practical value to the size of the sample carbonized. However, the cost of the carbonization test also increases with the amount of the sample, so that for preliminary surveys of a number of coals, samples of 25 to 1,000 grams usually are employed."

Dec 1, 1939

By Stanley P. Jacobsen

Samples of fine coal refuse were obtained from 11 coal preparation plants throughout the United States. These samples were characterized by ash analysis, particle size, and mineral composition. From the characterization, geographical locations, and the dewatering equipment being used by the plants, five sites were selected for obtaining bulk fine refuse samples. The selected coal preparation plants were using for final dewatering thickeners followed by: a vacuum disc filter, a filter press, a belt press filter, a centrifuge, and a settling pond. None were using thermal drying. The moisture content of the final cake varied from approximately 23% to 50% depending upon the feed material, flocculant addition, and the type of equipment. The filter press gave the lowest moisture content followed by a belt press and then either a centrifuge or vacuum filter. The centrifuge products were all dried to an approximate 5% moisture in a thermal dryer.

Jan 1, 1981

By A. C. Fieldner

Much activity is called for in the present period of hightened national effort, and wise direction of such a program must always be conditioned by positive knowledge gained in years of slow and painstaking study and development. Research and technologic investigations on coal by the Bureau of Mines have been described in a series of annual

Jan 1, 1941

By James R. Boyle

The value of Alabama's nonfuel mineral production in 1981 was $312.7 million, a decrease of $15.7 million from that of 1980. Output of most non fuel minerals declined; cement, crushed stone, lime, clays, and sand and gravel were the major commodities produced in the State. Alabama led the Nation in the production of crushed marble; was second in bauxite; third in native asphalt, kaolin, and oyster shell; fourth in bentonite, dimension marble, and fire clay; fifth in masonry cement; and sixth in common clay, ferroalloys, and lime.

Jan 1, 1983

By Charles L. Kimbell

In overall aggregate, the world's mineral industry in 1987 experienced a more satisfactory year than in 1986, at least insofar as its performance could be assessed from traditional statistical indicators. Production, trade and consumption seemingly advanced in the case of the majority of commodities, and prices for a number of commodities advanced. It was by no means certain, however, whether 1987 investment in mineral industry ventures would top the levels of 1986, when, in the case of petroleum industry investment expenditures there had been a sharp decline, this in contrast to evidences of a slight upturn in steel industry investment. World crude mineral output value was estimated at more than $1,084 billion, and the value added by minerals industry processing of this material probably raised the total value of the industry's production from primary materials to more than $2,600 billion constant 1983 dollars. Less easy too assess was the value of mineral commodities moving in international trade, but with a resurgence in oil prices from the 1986 levels, an increase above the 1986 $500 billion mark seemed assured. There are no comprehensive aggregate statistics on mineral consumption comparable to those on production and trade, but quantitative growth recorded for most major commodities suggested a favorable trend, particularly when coupled with a general (though by no means universal) upturn in unit prices.

Jan 1, 1989

By R. Y. Williams

The investigative work described in this report was undertaken by the Bureau of Mines under a cooperative agreement with the department of mining engineering of the University of Illinois and the Illinois State Geological Survey." The purpose of this agreement was to provide for a comprehensive investigation of coal-mining conditions in the State, with especial reference to the possibility of lessening waste in the mining and preparation of coal and of reducing the dangers to which miners are exposed. The Bureau of Mines paid particular attention to those phases of the investigation that were of general interest from their bearing on safety and efficiency in the coal-mining industry as a whole. Thus, it studied the occurrence of gas (methane) in the mines of the southern part of the State," tested the inflammability of the coal dust from many mines, examined the efficiency of the control of ventilating currents, and investigated the factors affecting the humidity of mine air with respect to their bearing on the occurrence of mine explosions. Following the establishment of the fact that under certain conditions dry bituminous coal dust is inflammable, there arose the problem of finding efficient methods of preventing or limiting coal-dust explosions. Experiments in the gas-and-dust gallery at the Pittsburgh testing station of the Bureau of Mines verified the fact that certain dusts that explode violently when dry are rendered inert by proper humidi- .fication of the atmosphere within the gallery, and the importance of humidity as a factor in limiting the inflammability of coal dust in a mine is demonstrated by the fact that there has never been in Illinois a dust explosion during the summer months, whereas the records show a number of dust explosions during cold weather. It is easy to see that the warm moisture-laden air that enters a mine in the summer must deposit moisture on cooling, whereas the cold and relatively dry air that enters in winter must take up moisture as it becomes heated in traveling through the mine.

Jan 1, 1914