Search Documents

By James D. Noll, M. Eileen Birch

A monitoring method for diesel particulate matter was published as Method 5040 by the National Institute for Occupational Safety and Health (NIOSH). Organic and elemental carbon are determined by the method, but elemental carbon (EC) is a better exposure measure. The US Mine Safety and Health Administration (MSHA) proposed use of NIOSH 5040 for compliance determinations in metal and nonmetal mines. MSHA also published a rule making for coalmines, but no exposure standard was provided. A standard based on particulate carbon is not considered practical because of coal dust interference. Interference may not be a problem if an appropriate size-selective sampler and EC exposure standard are employed. Sub micrometer dust concentrations found in previous surveys of nondieselized, underground coal mines were relatively low. If a large fraction of the sub micrometer dust is organic and mineral matter, sub micrometer EC concentrations would be much lower than sub micrometer mass concentrations. Laboratory and ?eld results reported here in indicate the amount of EC contributed by sub micrometer coal dust is minor. In a laboratory test, a sub micrometer EC concentration of 31µg m 3 was found when sampling are spirable coal dust concentration over three times the US compliance limit (2mg m3). Laboratory results are consistent with surveys of nondieselized coal mines, where EC results ranged from below the method limit of detection to 18µg m 3 when size-selective samplers were used to collect dust fraction shaving particle diameters below 1.5µm sub micrometer EC concentrations were ?7µg m3. In dieselized mines, sub micrometer EC concentrations are much higher.

Surface mining and reclamation of a southeastern Ohio site with sandstone-shale overburden resulted in (as compared to premining levels): 1) runoff volumes and peak rates that increased by a factor of from 2 to 10 during mining and after reclamation, 2) destruction of the "aquifer" perched on the underclay of the mined coal bed and gradual, but, as yet incomplete redevelopment of this aquifer after reclamation, 3) no immediate effect on another, lower perched "aquifer", 4) up to 100 times greater sediment concentrations in runoff. Results were influenced by increasing annual precipitation amounts through the period of record; 1978, 1979, and 1980 (postreclamation years) experienced precipitation amounts approaching or exceeding long-term normalcy for the area. Part of the reason that the site produced more runoff after reclamation than before mining is that the premine condition was one of an open, porous soil under woodland, while the postreclamation condition was one of a compacted, bulldozed soil. Sediment concentration results were influenced by failure of the postreclamation erosion control system and by a series of detention reservoirs above the stream monitoring station.

Jan 1, 1983

By Steven J. Page, John A. Organiscak

Laboratory crushing experiments were conducted on a range of low- to high-volatile bituminous coals to investigate the various factors influencing airborne respirable dust (ARD) generation. This research was conducted to identify the principles of ARD liberation from the coal product. Five U.S. bituminous coals were uniformly prepared and processed through a double roll crusher located in a low-velocity wind tunnel. Experimental factors studied included inherent coal seam constituents, coal grind ability, specific energy of crushing, product size characteristics, dust cloud electrostatic field, and specific ARD generated. The results of this investigation indicate that a combination of several factors are associated with ARD generation. One factor is the effect of coal rank, described by the inherent moist fuel ratio, on the product size characteristics, defined by Schuhmann size function parameters. Another key factor is the effect of air dry loss(ADL) moisture in the coal seam on the breakage-induced electrostatic field of airborne dust. The effect of these factors is that different percentages of <10-m coal particles are dispersed as ARD. A discussion of electrostatic field principles, coal ADL, and its effect on ARD generation is presented.

Jan 10, 1998

Coal mining in Indiana is limited to the south-western portion of the state, with coal currently being recovered in 19 counties. The coal-producing area of the state covers approximately 6,500 square miles. Although most of the coal in Indiana is recovered by surface mining methods, a small percentage is recovered through underground mining. To date, 40 percent of the known coal reserves have been removed. Indiana has about 33 billion tons of identified coal reserves, of which approximately 17 billion tons are recoverable using current technology. Of this recoverable coal, about 15 billion tons are recoverable by underground mining and 2 billion tons are recoverable by surface mining methods. The State of Indiana has regulated the environmental impacts of coal mining since 1941. Indiana was the second state in the nation to pass legislation requiring mined land reclamation. Its SMCRA regulatory program was approved July 29,1982, and its Abandoned Mine Land Program was approved July 29, 1982.

Jan 1, 1992

By F. Matanzo

This guide considers only nine of the many wire rope terminations used in the mining industry so use of the information presented for terminations not specifically addressed can be done, but with some risk. The nine terminations considered are: Flemish Loop with Steel Sleeve & Thimble, Flemish Loop with Steel Sleeve, Wedge Socket, Swaged Socket, Turn Back Loop with Aluminum Sleeve & Thimble, Thimble Splice with Four Tucks, V-Bolt Clip with Thimble, Zinc Poured Socket, and Epoxy Resin Poured Socket. The guide uses pull test data, axial fatigue test data, and data on sensitivity to poor workmanship, to rank the nine terminations with respect to these performance measures. A selection procedure is suggested and illustrated with an example. Failure data is used to identify the common modes of failure of each termination and so help the inspector direct his attention to the likely location for a failure and describe what he should be looking for. The data on which this guide is based is included so that as new data becomes available, the ranking order can be adjusted accordingly.

Jan 1, 1978

Coal research and related activities in 1964 by the Bureau of Mines resulted in many advances in the production, preparation, and utilization of this valuable natural resource. Mining research during the year was marked by work on hydraulic mining, coalbed degasification, mine drainage control, mine sealing, strip-mine rehabilitation, and quenching of mine-refuse fires. Bureau research continued to produce information leading to increased safety in underground mining. Such research included roof and rib control via bolting and bonding, pressure monitoring of coal and mine rock during mining operations, and development of safety devices for detecting conditions leading to roof falls. Other safety work was continued on methane detectors, coal-dust suppression, and mine ventilation equipment and techniques. Mine explosion and explosives research, mine equipment and materials, safety rule modernization, and safety education and training of mine workmen were continued. Coal storage and preparation work in 1964 ranged from freezeproofing of lignite for rail shipment, through washability studies of coals and washing equipment, to research on new ways to remove ash and sulfur from coal. Electric power production, which accounts for a major portion of the market for coal, received further study. Unique power generation systems, including coal-burning gas turbine and megnetohydrodynamic generators, were intensively investigated. Conventional power systems were improved through continuation of work on furnace performance, powerplant stack gas purification, and engineering and boiler water service.

Jan 1, 1965

By Eric E. Cather

A mineral survey of a portion of the Lake Eleanor RARE II area (No. 5807), Trinity County, California, was done by the U.S. Bureau of Mines and U.S. Geological Survey (USGS). Approximately 8,650 acres (3,500 ha) of the Lake Eleanor RARE II area not examined for this report had been previously investigated by U.S. Bureau of Mines and U.S. Geological Survey personnel and published as part of USGS Bulletin 1371-B, (Hotz, 1972) Mineral Resources of the Salmon-Trinity Alps Primitive Area, California. The report showed that the section included in the rake Eleanor RARE II area contained no metallic mineral resources. Geochemical sampling indicated that the Lake Eleanor RARE II area contains no potentially important mineral resources. About 4,650 acres (1,880 ha) of the eastern part of Lake Eleanor RARE II area were examined for this report. The Bureau of Mines was responsible for detailed examination and sampling of mines, prospects, and mineralized zones; the Geological Survey conducted geological, geochemical, and geophysical studies of the area. This area is underlain mainly by granitic rock and serpentinite.

Jan 1, 1981

Reduce the cost of modifying uranium well casings so that leaching solutions can pass through, but sand grains are blocked. Approach The well casing and surrounding cement are perforated at the mineralized zone by impinging them with high pressure water jets. How It Works A nozzle assembly is attached to a high pressure (15,000 psi) pipe and lowered into the well casing which typically is schedule 40 PVC (poly-vinyl chloride). The high pressure pipe line is extended down Into the casing until it reaches the mineralized zone. The upper end of the pipeline is then connected by a high pressure hose to the outlet of a 10,000 psi pump. Turning the pump on for 5 seconds causes a high velocity water jet to cut through the well casing and the surrounding cement. Figure 1 shows a high pressure pipe being installed in a well casing. Cutting small diameter holes in the casing allows the leachant to enter the casing and be pumped to the surface. However, the holes are small enough to prevent most sand grains from entering. Numerous holes are usually cut through the casing. The 3-nozzle assembly shown in Figure 2 cuts three holes, one above another.

Jan 1, 1978

By Carroll W. DeKock

Thermodynamic data for selected metal sulfates were critically evaluated and compiled as part of the Bureau of Mines program to provide a scientific base for use in developing new technology and predicting the feasibility of new processes. Values for Cp°, S°, H° - H°298, - (G° - H°298)/T, ?RC, ?Gf°, and log Kf as functions of temperature are given in tabular form. Thermodynamic data were compiled for Ag2SO4, A12(504)3, A12(S04)3?6H20, BaSO4, BeSO4, BeSO4?2H2O, BeSO4?4H20, CaSO4, CaSO4?1/2H20, CaSO4?2H2O, CdSO4, CdSO4?H20, CdS04?8/3H20, 2CdO?CdSO4, Cs2SO4, In2(S04)3, K2504, KA1(S04)2, KA1(S04)2?12H20, Li2SO4, L12SO4?H20, MgSO4, MgSO4?H2O, MgSO4?2H20, MgS04?4H20, MgS04?6H2O, MgS04?7H2O, Na2SO4, Na2S04?7H20, Na2SO4?10H20, (NH4)2SO4, NH4A1(S04)2, NH4A1(S04)2?12H20, PbSO4, Rb2SO4, T12SO4, and Zr(S04)2.

Jan 1, 1986

By C. S. Compton, D. R. Dolinar, D. C. Oyler

More than 80% of U.S. roof bolts are fully-grouted, but about 1500 roof falls are reported each year. Anchorage failure of a fully grouted bolt can occur when the roof is active near the top of the hole. This paper reports on an extensive series of short-encapsulation pull tests (in which the bolts are installed with only 1 ft of resin) that were conducted in the National Institute for Occupational Safety and Health (NIOSH) Mine Safety Research Laboratory and operating mines in WV and PA. The tests confirmed that poor anchorage can been countered under some weak rock conditions. Suggestions for improving anchorage are included.

By Xintan Chang

MFIRE is a computer simulation program that performs normal ventilation network planning calculations and dynamic transient-state simulation of ventilation networks under a variety of conditions. The program is useful for the analysis of ventilation networks under the influence of natural ventilation, fans, fires, or any combination of these. MFIRE simulates a mine&apos;s ventilation system and its response to altered ventilation parameters such as the development of new mine workings or changes in ventilation control structures, external influences (varying outside temperatures), and internal influences (fires). Extensive output enables detailed, quantitative analysis of the effects that the alteration will cause to the ventilation system. The program was developed at Michigan Technological University (MTU), Houghton, MI, with support from the Bureau of Mines. A personal computer (PC) version of the program was completed under contract for the Bureau by MTU. The purpose of this report is to document the installation and use of the PC version of the program MFIRE.

Jan 1, 1990

By Henry R. Ensminger

Brazil&apos;s gross domestic product (GDP) grew only slightly in 1988 to $277 billion at current prices.2 The growth rate was the smallest registered since 1983, when the rate was minus 2.8%. The economy&apos;s performance was strongly influenced by a 2% to 3% decrease in industrial production and civil construction. The mineral industry, however, countered the downward trend in the industrial sector and grew a modest 1.4%. In November, Brazil adopted a new Constitution that placed significant restrictions on foreign investment in the mineral industries. Under certain provisions of the new Constitution, foreign companies were prohibited from establishing new mining ventures in Brazil as sole or majority owners. They could now enter the mineral industry only as minority shareholders with Brazilian partners. Foreign companies already established in Brazil had a 4-year grace period to find majority Brazilian partners, or to establish vertically integrated processing operations (mining, processing, smelting, and refining). The new Constitution also prohibited foreign risk contracts for petroleum exploration.

Jan 1, 1990

By Gordon R. Sima

The contract is concerned with feasibility studies, design and fabrication of a group of prototype hand-held test instruments and machine-mounted test instruments for measurement of electrical shock hazards of mining machines. An instrument for use in open pit mining machine ground wire verification was proposed, developed, built, and tested. This report presents the design and operational theory of the open pit instrument as well as information on the program to improve the original prototype hand-held machine-mounted test instruments.

Jan 1, 1977

By H. M. Thorne

The Union of South Africa has been interested in oil shale for a long time, and deposits of oil shales, torbanites, and similar rocks have been found in many parts of the country. (Fig. 1.) Samples differ markedly in oil yield and in the characteristics of the oil. The strata vary in thickness, and most of the deposits that have been found are in unfavorable locations because of remoteness from markets or absence of transportation facilities. This report deals mainly with the torbanite deposit near Ermelo, Transvaal, in the Union of South Africa, and the operations of the South African Torbanite Mining and Refining Co., Ltd. (hereafter referred to as Satmar), in mining the torbanite, retorting it, and refining the crude oil.

Jan 1, 1954

To mine uraniferous sand-stone in an economically feasible and environmentally compatible manner without placing men underground. Approach Uraniferous sand is remotely extracted through a single borehole by cutting Into the are around the borehole with a high pressure water Jet, and pumping the resulting slurry to the surface. How It Works A 16-inch-diameter borehole Is drilled from the surface down into the burled mineral deposit, and the mining tool Is installed. High pressure water Is released as a jet from a nozzle In the mining tool to erode the are, forming a slurry that flows to the bottom of the cavity. The slurry Is drawn Into Inlets located near the bottom of the drill string. See drawing. After being pumped to the surface, the slurry is weighed, metered, and checked for radioactivity. It is then deposited Into one of a pair of sumps. Water collecting in the sumps drains Into an adjoining pond for reuse. Thickened are In the sumps is removed and placed In piles.

Jan 1, 1978

By Peter P. Kopas

Study, analysis, fabrication and testing for canopies on Roof Bolters and Shuttle Cars in coal seams under 48?.

Jan 1, 1980

By F. E. Walker

The Bureau of Mines determined total sulfur and sulfur forms for coal in 283 counties in 29 States and 2 fields of the State of Alaska. Specifically, organic, pyritic, and sulfate sulfur were measured of approximately 2,900 samples, and they include most of the coalbeds in the United States.

Jan 1, 1966

By F. E. Walker

The Bureau of Mines determined total sulfur and sulfur forms for coal in 283 counties in 29 States and 2 fields of the State of Alaska. Specifically, organic, pyritic, and sulfate sulfur were measured of approximately 2,900 samples, and they include most of the coalbeds in the United States.

Jan 1, 1966

By J. E. Spurr

"Zinc Industry in BelgiumBy March F. Chase, Consulting Metallurgist, Bureau of MinesBelgium for many years was the principal spelter producing country of the world. Gradually its production was surpassed by that of Germany, and Germany in turn lost first place by the production in the 77ti.tad States. For the ten years previous to 1914, 21.6 per cent of the world's spelter was produced in Belgium. Of this production approximately 40 per cent was exported. A large percentage of the balance was rolled and of the shoots thus produced a considerable quantity was also exported.From an economic standpoint even before the war, the Belgian industry was in a unique, if not praoarious, position. Dependent upon foreign countries for ore and foreign markets for sale of products, smeltor was at a distinct disadvantage when compared with some of those of other localities. These disadvantages were partly offset by cheap coal and labor and by whatever there is of value in experience and what we may term for want of a better expression smelting tradition. However intangible this latter may be, it did have and has today an influence on commercial operations.One must not overlook the effect it will have on the revival of the industry. It may not be the determining factor but the fact that for so many years this industry flourished in Belgium, and played such an important role in the industrial life of the country will decide many operators to attempt to re-establish their operations.In 1913 the Belgian spelter plants produced 204,220 long tons of spelter or approximately 20 per cent of the world's production. During this year 500,000 to of ore were treated. The actual value of all of the products derived from treating sine ore amounted to 225 million frames."

May 1, 1919

A maximum acceptable level of 2 mg/m3 of respirable coal mine dust in active mine workings was established, effective January 1, 1973, under the Federal Coal Mine Health and Safety Act of 1969. It is generally agreed that, as a result, coal mines in the United States are significantly less dusty than they were a decade ago. For example, operators of underground mining machines were exposed to between 3.9 and 6.5 mg/m3 of respirable coal mine dust during 1968-69; now they are exposed to between 1.3 and 1.8 mg/m3. Also, the incidence of underground sections cited for exceeding acceptable levels of respirable coal mine dust decreased during 1976-78, and the vast majority of all working sections are now in compliance. This improvement is very substantial by world standards. It must be regarded as a creditable accomplishment by the coal mine operators, federal agencies, and mine workers involved. Most of the improvement has been brought about by the use of existing technology to control, suppress, and collect respirable coal mine dust. Research and development by the Bureau of Mines has contributed significantly to the accomplishment by improving the methods for sampling, control, suppression, and collection.

Jan 1, 1980