Search Documents

By Roy E. Peterson

The Bureau of Mines conducted bench-scale research to evaluate materials which showed potential as low-cost reductants for use in the ironmaking industry. These materials were lignite, subbituminous coal, coal char, tree trimmings, refuse--derived paperboard, used crankcase oil, and peat. To compare their effectiveness, the materials were tested in the reduction roasting of nonmagnetic taconite and, except for oil and peat, in the reduction of iron oxide pellets to metallized pellets. Reduction was conducted in a 18-cm-diameter, rotary drum, which was externally heated in an electric furnace. Over 92 pct of the iron was magnetically recovered from a nonmagnetic taconite after roasting with any of the reductants, but greater quantities of reductant were required to achieve this when the waste materials were used. The fossil fuels were also more effective for metallizing pellets, although metallizations above 90 pct were also obtained with tree trimmings and refuse paperboard. However, refuse paperboard had to be frequently recharged to the furnace because it depleted rapidly.

Jan 1, 1983

By Robert L. de Beauchamp

The Bureau of Mines designed a chlorination apparatus to prepare CrCl2 free of CrCl3 by the direct reaction of chlorine and chromium. Equipment and procedures were developed for routine preparation of 25-pound batch quantities of anhydrous CrCl2. Calcium, iron, nickel, and silicon impurities were in the 0.01 to 0.05 percent range, and all other impurities were below 0.01 percent.

Jan 1, 1968

By M. John Brodie

This report reviews the regulatory environment as it pertains to waste rock management and disposal from mining operations, excluding coal and placer gold operations, in the \irate of Alaska. It is based on the EPA's staff position on an effective program to regulate mining waste as presented in the May, 1990 Strawman II document. The unique conditions which occur in pans of the state, including a fragile environment, high seismicity and permafrost, are identified. The special waste management practices which are necessitated by these conditions are delineated. The report provides a detailed outline of the current technologies that are suitable for designing, constructing, operating and closing a waste rock facility to meet environmental protection objectives. Cost implications to the mining industry of potential regulatory actions, such as the degree of groundwater protection, are examined.

Jan 1, 1992

By Allan E. Martin

As part of a comprehensive investigation of tie mechanism of desufurization of iron and steel by slags, the Blast Furnace Studies Section, Metallurgical Division, Bureau of Mines, in cooperation with the Institute of Technology-, University of Minnesota, has made a study of the forms in which sulfur occurs in blast-furnace slag. This report presents data on the three sulfides most important in iron smelting, namely, ferrous sulfide, manganous sulfide, and calcium sulfide. The tendency of these sulfides to form colloids in the molten slag was determined by an examination of quenched samples with an ultramicroscope. Vogt5/ conducted experiments on sulfide silicate melts and examined synthetic blast-furnace slags in a partly crystallized condition. His conclusions were that FeS, CaS, and bins, or isomorphous compounds, such as (FexCay)S and (MnxCy)S, were precipitated Prom the melt, depending on the composition of the slag. In all specimens sulfides were visible and were spherical.

Jan 1, 1941

By Laird Crocker

A goal of the Federal Bureau of Mines is to minimize the undersirable environmental conflicts and impacts associated with mineral processing operations. To help reach this goal the Bureau operated a citrate-process pilot plant for the removal of sulfur dioxide from lead smelter sintering machine waste gases to test the process. The process uses a carboxylate solution such as citric acid to absorb sulfur dioxide from waste gases. The absorbed sulfur dioxide is subsequently reacted with hydrogen sulfide to precipitate sulfur and regenerate the solution for recycle. Nominal capacity of the pilot plant was 1,000 scfm of 0.5 vol-pct sulfur dioxide gas. The pilot plant was operated for over 5,400 hr and produced about 55 net tons of sulfur. The operation demonstrated that (1) 99 pct of the sulfur dioxide could be removed from lead smelter sintering machining waste gases containing from 0.1 to 0.6 vol-pct sulfur dioxide, (2) sulfur precipitation and solution regeneration with hydrogen sulfide in conventional stirred vessels was readily controlled, (3) precipitated sulfur could be continuously recovered as a 99.S-pct-pure product by flotation and melting, and (4) 78 dry-vol-pct hydrogen sulfide gas could be produced from pilot-plant product sulfur, natural gas, and steam.

Jan 1, 1979

By M. Kanda

Two different techniques were used to make measurements of the absolute value of electromagnetic noise in and above an operating coal mine, McElroy Mine, located near Moundsville, West Virginia. The electromagnetic environment created by 300 volt dc and 480 volt ac machinery was measured. In one technique noise was measured over the entire electromagnetic spectrum of interest for brief time periods. The noise was recorded using broadband analog magnetic tape. The noise data was later transformed to give spectral plots. In the other technique, noise amplitudes were recorded at several discrete frequencies for a sufficient length of time to provide amplitude probability distributions. The specific, measured results are given in a number of spectral plots and amplitude probability distribution plots.

Jan 1, 1974

By Louis Schaffer

The objectives of the research were to determine whether a model health and safety program could be defined in terms which would enable its application to mines of all types, and, if such a model program could be defined, to determine through evaluations in two mining companies whether it would achieve measurable improvements. Volume 1 describes the model, how it was applied in the field and how it was evaluated. This, Volume 2, describes the literature and field research that preceded the model definition.

Jan 1, 1983

By Russell J. Gartrell

This report describes the engineering feasibility and economic advantages of using a steep angle conveyance (SAC) system in conjunction with medium and large draglines to transport spoil in a typical Western Coal Mine. The SAC system, including a receiving hopper, a steep angle conveyor and a sticker/spreader, is capable of processing overburden material at the rate of 7,000 tons/hr. The unique feature of this system is the steep angle conveyor which transports the overburden material from the pit bottom to the top of the spoil at angles to 45 degrees. Compared to other means of cross-pit conveyance considered during this study, the SAC system offers the advantage of easier operation, lower conveyance cost and greater mobility. The results of this study have shown that integration of the SAC system into both established and planned new mines would improve the overall mining operation, expand the operating capability of existing equipment and reduce mining end reclamation cost.

Jan 1, 1977

By G. Andrews

This case study details the process that was used for project planning and permitting for the Greens Creek Mine, located near Juneau Alaska, as seen through the eyes of one of the primary environmental consultants. This case shows how a Company could involve the public and the agencies in the early 1980's and develop a project sensitive to concerns expressed with a high level of environmental protection. Comparisons are made to the current environmental permitting situation. Initial baseline studies performed during the exploration phase provided helpful information for more detailed environmental work in 1980-1981 as planning and permitting formally got underway. Since the mine was in a National Monument and abuts up to a designated wilderness, the Monument Manager administered the project for the lead agency, the USDA Forest Service. Planning and permitting progressed smoothly to a Final Environmental Impact Statement (FEIS) in 1983. Metal prices were depressed when the FEIS was completed and the project permitting proceeded slowly. Ownership changed several times in the mid-1980's. New owners re-evaluated the project and suggested five changes that required a supplemental EA prior to development. The project was fully permitted and started construction in 1988. Operation began in 1989. Today the environmental process in southeast Alaska is now much more complex, detailed, expensive, and time consuming than in the early 1980's. Significant issues discussed that may impede development and operation include overlapping agency jurisdictions, personal agendas of agency staff, conflicts between agencies that impede project progress, changing regulations, and a well organized environmental opposition.

Jan 1, 1993

Improve the Bureau-developed system for locating and communicating with miners trapped underground following a mine disaster. Approach Include in the wireless system a portable second-generation transceiver that is more reliable, compact, easier to deploy and operate, and ruggedized to withstand a mine environment. How It Works In an emergency, the new transceiver is snapped onto a caplamp battery for power. (Normally the 1 1/2-pound transceiver is either carried by the miner or is strategically located in the mine.) Its antenna wire, coiled inside the transceiver container, is removed and deployed in a roughly square configuration around a coal pillar or on the mine floor. The antenna consists of 300 feet of lightweight wire, which provides a large magnetic moment while remaining intrinsically safe, The photograph shows the

Jan 1, 1981

By James H. Aase

Shales from 10 locations in Michigan were sampled, tested, and evaluated to determine their suitability as raw materials for producing lightweight aggregate by rotary-kiln methods. Sampling procedures and the geology of the shale units tested are discussed. Preliminary testing in a muffle furnace preceded extensive testing in a l6-inch by 14-foot rotary-kiln. Rotary-kiln products from these shales ranged in weight from 35.5 to 61.2 pounds per cubic foot (pcf). Concrete test specimens made pith selected aggregates were evaluated to determine the qualities of the concrete. Compressive strengths of the concrete ranged from 2,830 to 4,240 psi after 28 days of curing. Unit weight of the concrete ranged from 94.8 to 101.5 pcf. Lightweight aggregate suitable for use in structural concrete meeting ASTM standards was produced by the rotary-kiln method using shale samples from two locations.

Jan 1, 1967

By Terry S. Cory

This report describes the results of a measurement program to determine the broad spectral characteristics of both differential and common mode noise on phone lines in three coal mines; and, signal attenuation spectral characteristics on the same broad basis over phone line strings with taps/branches. The frequency range used was baseband -1000 Hz for resolution bandwidth ranging from 100 Hz near baseband to 30 KHz near I MHz. The signal attenuation measurements were performed on all three "legs" of taps where possible and applicable. Results were obtained comparing shielded and unshielded phone lines In one mine. The results include an improved electromagnetic noise chart for coal mines showing variations with types of mines, topology, and location of noise sources; also, fundamental high-frequency limit on untreated phone lines in coal mines is identified

Jan 1, 1981

By W. P. Diamond

The direct method test was developed for general mine safety applications by the U.S. Bureau of Mines in the early 1970's to measure the gas content of coal samples obtained from the relatively shallow depths of eastern U.S. coal mines. Over time, applications for gas content data evolved which required increasingly accurate desorption values. It became evident that some of the inherent weaknesses in the original direct method test could best be addressed by abandoning the water displacement based desorbed gas volume measurements. The ideal gas law based modified direct method (MDM) and associated desorbed gas volume measurement apparatus was developed to provide the most accurate desorption values possible for rock samples obtained from any gas-bearing strata. The MDM has a number of significant advantages, including: (1) increased accuracy, especially for low gas content samples, (2) a test apparatus with an integral sampling port to facilitate the collection of uncontaminated gas samples, (3) an inherent head space effect correction in the periodic MDM desorbed gas volume calculations, (4) measurement of positive and negative desorbed gas volumes, (5) elimination of differential gas solubility effects as a source of error inherent in the water displacement methods, and (6) a compact and rugged test apparatus that along with the elimination of the ?glassware? required for the water displacement methods, facilitates its use in the field.

Jan 1, 2008

By D. D. Bush

Based on the results of this study, the underhand cut and fill stoping method, with mass destressing, is an effective method for controlling rock bursts and falls of ground for deep mining in the Coeur d'Alene Mining District. The procedure can be utilized to pull highly stressed pillars by converting from conventional overhand stoping methods or used as a primary recovery system. During the demonstration, only one minor rock burst occurred, with no injuries. The system facilitates accurate placement of vertical boreholes for effective mass destressing. Each mining cut is filled with cemented sandfill overlying a timbered mat that forms the back for the succeeding cut. For this demonstration, a cemented fill was mixed on the surface and piped to the stone. Costs for pillar recovery by this method are comparable and are considered cost effective over conventionally timbered overhand mining as a pillar recovery method.

Jan 1, 1982

Objective: To identify and evaluate a permanent stopping to direct ventilation airflows in large-opening metal/nonmetal mines.

May 1, 2006

By Paul C. McWilliams

The U.S. Bureau of Mines has, primarily through its contract program, used large-scale centrifuges to determine design criteria for tailing embankments. The centrifuge runs were made at two installations, the University of Cambridge, Cambridge, England and Sandia National Laboratories, Albuquerque, NM. The major problems considered were as follows: slope stability of embankments, modeling erosion and seepage, use of the phreatic surface level to ascertain the validity of centrifuge modeling, and the effects of compaction and weathering on a tailings embankment. This report summarizes the results of the four test series conducted at University of Cambridge and Sandia National Laboratories. A review of prior centrifuge applications to mining problems is included. Consideration is given to future centrifuge application to mining problems in both soil and rock mechanics.

Jan 1, 1989

By Patrick J. Cain

The fatigue-failure characteristics under high-frequency (10 KHz) cyclic loading were determined for a marble, granite, and quartzite. The rock speci-mens were cyclicly loaded (using a high-power piezoelectric sonic transducer) at a constant strain amplitude generated by forming a longitudinal standing stress (strain) wave in the cylindrical test specimen. The number of load cycles required to fail each rock type at a given strain amplitude was deter-mined. The fatigue fractures were tensile in nature and the fracture load amplitudes were as low as 30 pct of the static tensile strength. Also the internal heating of the rock caused by the material damping (internal friction) was measured. The damping and internal heat generation in the specimens was analyzed to show that nearly all of the power input can be accounted for as a change in enthalpy in the specimen. Using these results the thermal strain in the rock was calculated to evaluate its contribution to fatigue failure. The thermal strain was found to range up to 30 pct of the dynamic strain amplitude depending on the load amplitude and the number of load cycles. The specific energy required for failure was determined and possible applications of the high-frequency fatigue fragmentation process are discussed.

Jan 1, 1975

By Ren G. Dong, Thomas W. McDowell, John Z. Wu, Chris Warren, Dan E. Welcome, Chun L. Dong

Hand forces are important factors for risk assessment of hand-arm vibration syndrome (HAVS).1 Grip force is one of the most important force components in the operation of powered hand tools. A considerable number of studies on grip force have been reported. It is well known that the grip force applied on a cylindrical handle is not uniformly distributed on each axis across the center of the handle cross-section.2 Therefore, maximum and minimum orientations of grip force exist around the handle. Such orientations have not been clearly identified. In a recently proposed international standard (ISO/CD 15230, 2005),3 it is stated that “the direction of the main gripping force is generally parallel to the z-axis defined in ISO 8727.” 4 This assertion is questionable, and further examinations are required. The objective of this study was to establish a fundamental theory on the distribution of the grip force around cylindrical handles. Methods As shown in Fig. 1, the grip force is defined as a vector composed of normal and shear components (FN & FT) in this study. Fig. 2 shows the hand coordinate system defined in this study, together with the ISO systems.1,4 Based on this novel grip force definition, we derived four fundamental properties and a theorem. More significantly, we formulated a novel hypothesis: similar to Mohr’s circle of stress, the normal and shear components can be represented approximately using an ellipse on the plane of the two force coordinates, as shown in Fig. 3. The maximum and minimum grip normal forces are termed as the first principal grip force (F1) and the second principal grip normal force (F2), respectively. Their corresponding orientations are termed as the first principal grip angle (a1) and the second principal grip angle (a2). A series of experiments were conducted to test this hypothesis. Twelve

Jan 6, 2006

By Frederick H. Raab

An electromagnetic (EM) system for the location of trapped mine workers at coal-mine (300 m) depths has been developed. The use of such a system in deep mines (1-km depth) requires transmission at extremely low frequencies (ELF) and a reduction in the effective noise level beyond that which can be obtained by acceptable Integration times. Automatic-noise-cancellation (ANC) techniques reduce the effective noise level by combining several received signals that contain correlated noise. Such signals can be obtained either from a remote magnetic antenna or a local electric antenna. During Phase III of this program, real ELF noise data were acquired and used to test the ANC algorithms developed during Phase II. The ELF noise data were obtained from analog recordings made by Develco under another Bureau-of-Mines contract. Digitization was accomplished by an ND converter that was added to a GMRR computer. Phase III tasks Included preparation of software for digitization, computer-computer communication, data processing, and statistical analysis. Useable data were obtained from eleven half-hour tapes containing noise from one axis of the primary antenna and three axes of the remote antenna. The overall average Improvement in SNR was 4.1 dB. However, the average Improvements for the Individual X, Y, and Z axes were 4.2, 11.9, and -1.9 dB, which roughly follow the observed noise power. Nonlinear processing was not effective with this noise.

Jan 2, 1984

By H. E. Peterson

Rhenium occurs in very small quantities (12).4 In order for the Federal Bureau of Mines to conduct an investigation of rhenium sources and methods of extraction, it was necessary to devise improved techniques for detecting and measuring minute quantities of the metal. A modification of the procedure of Malouf and White (46) was developed which can be used to detect rhenium in concentrations as small as 0.1 part per million and can be used to measure quantities of 1.0 part per million. It can be used for the analysis of siliceous and calcareous ores, of molybdenite concentrates, of fumes, of flue dusts, and of other metallurgical products. Development of the method involved devising an amine extraction procedure for separating rhenium from all interfering elements except tungsten and a selective distillation procedure for separating rhenium from tungsten. Adoption of these separation procedures permits use of large samples and precise determination of rhenium by colorimetric analysis of the thiocyanate complex of rhenium by means of a spectrophotometer.

Jan 1, 1961