Search Documents

By Wayne Rogers, Kell Monro, Arthur Pacunana

The Phu Kham Copper-Gold Operation (PKM) is a large-scale open pit mine located in northern Laos. It was developed and is operated by Phu Bia Mining Limited (PBM) a Lao-registered subsidiary company of Australian incorporated, PanAust Limited. Production commenced at Phu Kham in 2008. Since the second half of 2016, there has been a significant increase in ore hardness and this has negatively impacted the PKM concentrator and resulted in lower SAG mill throughput rates. Over the remaining life of mine, the changing ore body and increase in ore hardness is forecast to continue as the pit deepens and the availability of softer blending ores reduce. To manage this risk, PKM initiated a Hard Ores Management Program to determine the most effective way to improve the mill throughput of harder ores. This involved conducting a number of innovative and process control driven blasting trials to optimize run-of-mine (ROM) fragmentation and other blasting outcomes. From 2016 to 2017, the performance of high powder factor blasting, electronic detonators and fast timing, high velocity of detonation (VOD) explosives, double-priming, and deck blasting, were individually and systematically assessed. The success of each blasting trial was then based on a ‘value for money’ criteria. This criteria is a cost / benefit analysis that weighed-up the additional cost to implement the trial against the measured improvement in mill throughput. Electronic and high VOD 90:10 emulsion:ANFO blasts were determined to have the best value for money, achieving an increase in mill throughput of 54% compared to baseline. This paper discusses how the implementation of an innovative and process control driven blasting trial methodology was able to successfully manage the hard ore challenges at PKM. In addition, this success was achieved without any major cost implications, safety incidents or process plant set-backs.

Jan 1, 2018

By N/A N/A

Aw a rd winners from the University of MissouriRolla. Back row from left: Seok Bin Lim, Chris B o l l i n g e r, Adam Kre s l e r, Scott Geer, Joseph Cohn, and James (Buck) Hawkins; Front ro w f rom left: Dr. Worsey, Trish Robertson, and Fio G i a n a

Jan 1, 2004

By Ronald L. Cocklin, Vivian Patz

Blasting techniques are becoming increasingly sophisticated as the need for improving mining efficiency grows. One of the areas of blasting that has never been fully exploited, due to a lack of a control and reliability, is the initiation of explosives. Expert Explosives have taken on the challenge to not only provide an initiation system that offers control and reliability, but also provide benefits that are critical to enhanced mining productivity. These benefits can only be delivered through the medium of electronics and computer controlled systems.

Jan 1, 1995

By John Babcock, Gregory Poole, Ron Hudson

In January 2007, Fultondale Alabama opened a new elementary school. Site work at the old school location included blasting activities and the old school building was scheduled for demolition. With help from Apache Construction, blasting was scheduled to be performed in close proximity to the old school building prior to the demolition. Arrangements were made to perform extensive monitoring on the old school building during the blasting activities. The monitoring plan for the project included: • Pre and post blast inspections were performed on the structure; • Conventional crack monitors were installed at 22 locations throughout the structure; • Digital displacement monitors were installed at 6 locations on the structure; and • Seismographs were used to monitor structure vibration at 6 locations and ground vibrations at 9 locations. Blasting activities were allowed to produce vibration levels well above the safe levels established by the U.S. Bureau of Mines (USBM). Vibration levels up to 7.44 in/sec were recorded with no damage noted. Permanent deformation was recorded on vibration levels of 9.68 and above. Not only did this project reinforce previous studies which indicate that concrete block walls can withstand vibration levels well above 2.0 in/sec, this study was also a good example of employing new technology to help determine if/when damage occurs on a specific structure.

Jan 1, 2009

By Young-Dong Cho, Yonghun Jong, Dong-See Shim, Seokwon Jeon, Chung-In Lee

The most important operation in the tunnel blasting procedure is to create an opening in the face in order to develop more free surface in the rock mass. This operation is highly dependent on the cut holes. In general, the burn-cut or V-cut is commonly adopted to blast the cut section. But, these traditional methods often raise problems. There are instances (a) that the actual advance is considerably less than the designed advance depending on the rock mass, (b) that they cannot sometimes enlarge the free surface efficiently and (c) that the blast vibration resulted from the cut blast exceeds the allowable vibration level. In order to resolve the problems, many different kinds of the cut blast can be considered.

Jan 1, 2005

By Douglas Bartley, Robert McClure

This paper discusses the advances in programmable, testable high accuracy electronic detonator technology. The operation and safety of electronic detonator systems are required to meet rigid safety standards and withstand the demanding environment of in-field applications. These requirements are discussed through comments on existing safety requirements in Europe.

Jan 1, 2000

By Zach Ellis, Dusty Fisher

Lightning is a major concern in the explosives industry. The enormous amount of energy delivered to the Earth from a single bolt of lightning is more than capable of detonating explosives. Although explosives incidents caused by lightning strikes are rare, lightning is of great concern to blasting professionals who spend many hours working on or near loaded blast patterns.

Jan 1, 2015

By Robert Benedetti

This paper describes various mitigation methods in order to reduce the maximum acceleration of the floorboard of hulled vehicles when explosive charges buried in water saturated sand were detonated beneath them. The effects on floorboard acceleration of adding a vehicle hull, several types of floorboard bracing, the use of foam to fill the gap between the floorboard and hull, and the use of foam to isolate the floorboard from the hull have been investigated. Small scale testing was conducted, which used bar magnet velocity gages to measure the velocity as a function of time of the center of the floorboard, directly over the charge, where the acceleration was expected to be greatest.

Jan 1, 2012

By He Guangyi

Combining living examples, the paper introduces the controlled chamber standing shot of more than 3000t explosives initiated at one time with Nonel under complicated circumstances and the experience obtained to keep environment safe and favour mechanical rock cleaning.

Jan 1, 1998

By James Rowland, Marcia Harris, Richard Mainiero, Michael Sapko

All explosive materials produce a cloud of reaction products, the most toxic of which is nitrogen dioxide (NO2). In the study reported here, 4.5-kg (10-lb) charges of blasting agent confined in either thin-wall 10-cm (4-in) diameter galvanized pipe or 10-cm (4-in) schedule 80 seamless steel pipe were detonated in a closed chamber. The detonation gases were analyzed for NO2, nitric oxide (NO), ammonia (NH3), hydrogen (H2), carbon monoxide (CO), carbon dioxide (CO2), nitrogen (N2), oxygen (O2), and methane (CH4). Data were evaluated to determine the kinetics of the oxidation of NO to NO2. Analysis revealed that the only mechanism for NO loss for the conditions existing in the chamber was the reaction 2NO + O2 6 2 NO2. The rate constant was 2.08 ?? 10-38 cm6 molecules-2 sec-1 for the rate equation -??d [NO]/dt = K ?? [NO]2 ?? [O2] for NO concentrations up to 100 ppm. The rate constant is in agreement with that recommended by Baulch, Drysdale, and Horne (1973).

Jan 1, 2006

By J Lyall Workman, Peter N. Calder

"Large hole rotary drilling is one of the most common methods of producing blastholes in open pitmining. Large hole drilling generally refers to diameters from 9 to 17 inch (229 to 432 mm), however aconsiderable amount of rotary drilling is done in diameters from. 6% to 9 inch (165 to 229 mm). Thesesmaller diameters are especially prevalent in gold mining and quarrying."

Jan 1, 1996

By Gregg A. Scott, Gordon F. Revey

"The Folsom Dam is a 340-foot-high concrete gravity dam with embankment wing dams located on the American River about 20 miles northeast of Sacramento, California. Folsom Dam is operated andmaintained by the U. S. Bureau of Reclamation (Reclamation). As part of the Central Valley Project,Folsom Dam is a multipurpose facility providing water supply storage, flood control, power generation, and recreational opportunities."

Jan 1, 1999

By Gennaro Di Lauro, Laura Meraviglia, Demostenes Efstratiadis, Danilo Coppe

This paper presentation regards the European Union’s project “I.C.E.A. - Identification Colors of Explosives and Blasting Accessories (Agreement number – HOME/2010/ISEC/AG/071 – 30 – CE – 0447240/00-11), submitted under the call for proposal “ISEC 2010 ACTION GRANT” of the “Prevention and Fight against Crime” Program of European Commission. The main objective of the project is to simplify counter-terrorism security measures and the procedures for visual identification of blasting devices.

Jan 1, 2015

By Guillermo Silva, P. Katsabanis

The conventional approach to design wall control blasts relies on the borehole pressure as the most important explosive parameter. Borehole pressure is intimately linked to explosion pressure, which in turn is related to the detonation pressure of the explosive. For fully coupled charges, the borehole pressure is equated to the explosion pressure, while for decoupled and decked charges its value is typically calculated under the assumption that the explosion products behave like an ideal gas when they expand into the volume of the hole.

Jan 1, 2003

By Harry Verakis, Thomas Lobb

Over the past decade, approximately 5.1 billion pounds of explosives were used annually, on average, in the United States. Most of the explosives were used by the mining industry. The coal mining industry was and still is the dominant user of explosives. About two-thirds of the explosives consumed was used in coal mining.

Jan 1, 2003

By Des Bolton

With the introduction of Cast Blasting techniques, field controls of Drilling & Blasting operations became more important. New drills were purchased which were equipped with sophisticated instrumentation and more accurate drilling plans were required. Concurrently a decision had to be made on the replacement of borehole logging equipment owned by the mine. The use of a contractor to log blast boreholes was eventually decided upon, the information gained from this operation is used in the short-term drill and blast planning and may also be used to assist in the coaling operation if density I quality correlations prove acceptable.

Jan 1, 1994

By R. F. Favreau, P. Favreau

Rock excavation is the first process in the cycle of operation of a mine, and efficient blasting is paramount to the profitability of the mine. The traditional way to design blasts has been by trial and error, based on the experience of the designer. This is probably the only important engineering practice which continues to be done without a precise engineering technique. The efficiency of most other mine processes has been improved by the use of high-tech, while a majority of blast design has not yet profited from the advantages of the computer. However, with the advent of the high-tech blast simulator Blaspa, it has become possible to design the parameters of the blast according to normal engineering practices. Over the last 50 years, the chemical and physical mechanisms which occur during a blast have come to be identified; they are reviewed in section B. Although these mechanisms are complex, they have nevertheless been expressed in terms of mathematical equations which have been assembled together in the computer to create the blast model Blaspa.

Jan 1, 2002

By Barend Botha, Trevor Davids

The presence of an extensive soft siltstone layer in the middle of the inter-burden sequence of rocks at Syferfontein Colliery in the Republic of South Africa prompted tests to determine the effect of different mid-column decks of inert material in the siltstone layer. The objective was to achieve significant cost savings in explosives use whilst not degrading dragline productivity. An important factor that had to be considered was that the initiation systems available in South Africa are not accurate enough to ensure simultaneous initiation of explosives decks in a blasthole. A number of inert materials were tested including ash, drill cuttings, river sand and crushed stone. It was found that the ash, drill cuttings and river sand did not effectively attenuate the shock wave and that the risks of sympathetic detonation or partial disruption of one or the other explosives deck in a blasthole was high. This became much worse when the inert material was saturated with water. Crushed rock was the most effective in attenuating the shock wave, but this material was very expensive to use because it had to be imported onto the mine.

Jan 1, 2000

By Brandon Axelrod

This paper follows a student’s interest in explosives which began at an early age after watching a television program highlighting explosives engineering. The use of explosives in those programs led to curiosity about how one gets involved in the industry. These programs enticed the author to further investigate the explosives industry leading him to an explosives camp for high school students. After attending the camp, this passion further developed into postsecondary education.

Jan 1, 2015

By Steve Dillingham

Here in the United States, as well as around the world, pose a daily dilemma - to wash or not to wash. Let’s face it, all trucks, especially our industry work horses - bulk trucks - get dirty. We all know that these units can be very expensive and washing them keeps your business investment looking new, improves public relations, fuels company pride, and facilitates equipment safety and preventative maintenance inspections.

Jan 1, 2001