Search Documents

By Calvin Konya, Anthony Konya

State and Federal construction specifications require the Blasting Contractor to prepare a Master Blasting Plan which is reviewed by the Owner’s Representative. The Master Blasting Plan requires the Contractor to submit the design of a typical blast. Most blasting specifications also require the Blasting Contractor to submit Daily Blasting Plans. The Master Blasting Plan and the Daily Blasting Plan require that the Blasting Contractor also submit the types and quantities of explosives and initiators used. The specifications also request that the Blasting Contractor submit the pounds of explosive used per delay for both production and presplit blasts. The Blasting Contractor may also be required to predict the anticipated ground vibration and air overpressure levels for the proposed blasts. There are equations that can be used to predict the ground vibration. There are also equations that can be used to predict the air overpressure levels. The data for these equations were primarily derived from quarry and surface coal mine and some construction blasts. Data from major construction projects were analyzed in this study to determine new air overpressure propagation equations for construction blasting. These new prediction equations compare calculated results analyzed from field data with other existing air overpressure prediction equations. Production blasting air overpressure values are also compared to air overpressure from presplitting

Jan 1, 2015

By Yoshiharu Tanaka, Toshiyuki Ichijo, Masaaki Yamamoto

We utilized electronic detonators (EDs) to investigate the effect of high detonator delay accuracy on overbreak, remaining rock damage, and surface smoothness, in comparison with that of long-period delay detonators (0.25 sec interval) PDs. The experiments were conducted in a deep mine, in a test site region composed of very hard granodiorite with a seismic wave velocity of about 6.0 km/see and a uniaxial compressive strength, uniaxial tensile strength, and Young's modulus of 300 MPa, 12 MPa, and 73 GPa, respectively. The blasting design was for a test tunnel excavation 8 m in cross section, with an advance per round of 2.5 m. Five rounds were performed, each with a large-hole cut and perimeter holes in a 0.4-m spacing charged with 20-mm-diameter water gel explosive to obtain low charge concentration. EDs were used in the holes on the perimeter of the right half, and PDs were used in all other holes.

Jan 1, 1995

By Cathy Aimone-Martin, Robert Brentar, Brent Meins, James Lauer

Vibration measurements of multi-story structures in an urban environment began 3 years ago in New York City during close-in blasting to adopt correct measurement procedures and recommend revised ground vibration limits that best characterize cracking potential in mid- to high-rise structures. Two broad categories of structures included non-engineered 4- to 6-story multi-family unreinforced brick masonry buildings, built from the late 1800s to around 1930, and post-WWII, high-rise structures of reinforced concrete and steel rising 12 to 40 stories. In-ground vibration limits similar to those recommended by the U.S. Bureau of Mines safe criteria, developed for 1- and 2-story residential structures, are imposed by the New York City Fire Code. However, these limits are often lowered by project engineers or New York Department of Buildings when blasting is planned near buildings designated Landmark or historic and classified as fragile or vibration-sensitive. Seismograph measurements to determine compliance with in-ground velocity limits currently employ geophones mounted to basement walls and on concrete slabs overlying rock. These measurements cannot be correlated with upper structure cracking potential and are often exceeded, resulting in excessive and costly downtime to allow post-blast damage investigations.

Jan 1, 2014

By Ed Coulter

Nevada has a population of 1.2 million people of which only 21% or 312,rIXl are native born Nevadans. he population between 1980-1990 grew a record of 389%. and ls the fastest growing state in the union. While only 2.5% of the total population are direct employees of the mining industry, excluding Reno and Las Vegas, one out of every three people living in Nevada work for a mining related industry.

Jan 1, 1991

By Stephen H. Chung

The blasting performances identified above are considered to be the most practical ones for judging the effectiveness of a design combining explosives / rock / drill pattern. In a total blast design process, productivity relates closely to both fragmentation and heave / displacement of muck. In cast blasting, the more overburden displaced by explosives, the less blasted material there is left to be removed with mechanical equipment such as draglines or trucks. For wall protection and dilution control, estimates of the maximum extent of cracks / damage generated in situ due to blasting will help determine the location for drilling and loading perimeter blastholes.

Jan 1, 1994

By Stephen H. Chung, Kevin Atherton

The main purpose behind this preliminary study was the reduction of costs while maintaining productivity. Finding a way to achieve this balance without compromising controls on safety and quality of blasting results is of continual interest to the mining industry and of particular interest when ore of lower grade is being mined.

Jan 1, 1998

By William C. Geitz

"Lightning has always posed a serious threat to blasting operations, especially wkhin the mining and construction industries and operations involving the manufacture, transport, storage and handling of explosives. In recent years, technological advancements in communications systems and microprocessors have significantiy improved the accuracy and efflliency of lightning detection and warning instrumentation. These advancements have increased the availabilii of highly reliable,accurate and affordable systems for use within the explosives arena."

Jan 1, 1991

By Don McCarthy

Modern mining has been dominated by the drill-and-blast method for more than a century. There have been steady improvements in drilling technology, explosive products, methods of initiation and integration of the two techniques but the essential cyclical nature of drill-and-blast rock excavation naturally limits continuous improvements in cost and productivity. Dynamite and safety fuses, compressed-airdriven tools, and most of the crushing and grinding machinery in use today were all developed before 1900. Moreover, virtually every mechanized mining system used today was in use by the late 1950’s.

Jan 1, 1998

By James W. Reil, Douglas A. Anderson, Steven L. Burchell

A total of 26 full-scale production blasts at three sites were extensively monitored with sophisticated instrumentation systems to determine the benefits of "ore. accurate detonators. The new and "ore accurate MS electric Masterdet detonator was tested against conventional detonators to determine any increase in productivity outputs. All blast design parameters between paired blasts were kept as constant as possible with the only difference being the inherent accuracy of both detonator systems.

Jan 1, 1989

By Randall S. Marks

Bonneville Dam, completed in 1938, included the smallest and busiest lock on the Columbia and Snake River Navigation System. To expedite barge traffic through this restriction, a new larger lock was designed and contracted by the U.S. Army Corp of Engineers.

Jan 1, 1997

By Richard R. Brochu

At the International Society ofExplosives Engineers Annual Conference held in Nashville, Tennessee in February 1995, a Seismograph Standards Committee was established. The purpose of this wmmittee was to develop objective performance specifications for vibration measurement instrumentation and field use practices. It was also understood that due to geology, temperature, and moisture in the soils, it is not possible to design and build an instrument to give ‘results which are absolutely comparable for ground vibration. It was, however, considered essential to standardize instrumentation by which vibration can be measured under closely defined conditions so that results obtained by users of seismographs are always the same ,&thin stated tolerances.

Jan 1, 1998

By Richard Goodridge, Stephen Thomsqn, S Rodgers, D Tunaley

The mining, quarry and construction industries are facing’new challenges everyday. These challenges can be imposed by economic objectives or through external factors such as extreme geological conditions. Simultaneously, all mines, quarries and construction sites are facing more and more stringent environmental requirements.

Jan 1, 1998

The common approach of designing blasts on a trial and error basis is quickly coming to an end. When utilizing the full scale blast environment, trial and error can quickly become cost prohibitive and leaves much to be desired in terms of true blast diagnostics. In these situations testing is usually only continued until a perceived improvement is achieved and when the gross undesirables in blast results are removed. This does does not preclude, however, that further improvements of up to 100% or more can not be obtained.

Jan 1, 1991

By Craig Wilbour, John Stimberis, Rob Gibson, Lee Redden

An avalanche is a snow slide. A simple explanation is that the snow on a slope will slide (avalanche) when the snow strength can no longer support its own weight. Snow avalanches happen when the load from snowfall or ram on a snow slope increases faster than the stre n g t h of the bonds between snow crystals. Avalanches can also happen when the strength of a buried layer decre a s e s . Active avalanche control is the intentional triggering of slides. Washington State Department of Tr a n s p o r t a t i o n (WSDOT), does avalanche control to minimize the chance of natural avalanches into traffic. Avalanche control work is done all over the world by: highway departments, ski resorts, railroads, mining operations, utility companies, and other activities threatened by avalanches. The majority of active avalanche control is done with skis, by explosives, or exploding projectiles. Blasting techniques and practices have evolved to fit the specific needs of avalanche contro l . Passive avalanche control is the use of engineered s t r u c t u res such as snow sheds, bridges, or snow supporting devices, to permanently protect a specific location from avalanches. The problem is that these struct u res are extremely expensive. There are a variety of passive avalanche control measures as well as the active m e a s u res used to protect the highway over Snoqualmie Pass. As traffic volume and use expectations incre a s e , m o re extensive passive measures will be needed to keep avalanches from affecting the highway.

Jan 1, 2004

By AJ Rorke, JD Botes

Presplit blasting in strip mines is aimed at creating a safer wall to work under during the coaling operations. Good quality presplits are also necessary for effective throw blasting and drainage of the blast block. A less obvious but important function is full coal recovery. Optimum Colliery has been experiencing rock freezing against the presplit highwalls. The rock formed in patches along the highwall and trapped coal beneath it. The material that was &ozen comprised the rock between the back row of holes and the presplit and was often up to 3 m thick (the stand off distance between the back line and the presplit). The cozen rock formed predominantly along the bottom halfor bottom two thirds of the highwall. Along the top portion of the highwall, the presplit crack was usually well formed with visible barrels. This problem, or similar variations of it, is common on many South African strip-mine operations. Investigative work was carried out at Optimum Colliery to correct the problem. This paper presents the information and measurements that were made and discusses the solutions that have been applied to solve the problem. It was found that there were two independent causes for the tiozen material, with each contributing more or less to the frozen rock along the highwall. It was found that the presplit was not forming properly in places, especially closer to the bottom of the highwalls. The reasons and the solutions are presented. The second cause was found to be associated with reduced detonation velocity in the back line holes coupled with low confinement from long delay periods. Emulsion explosive that is sensitised with air bubbles was found to be prone to this phenomenon near the back of high-energy blasts. A change in the explosive formulation in the back-line holes, together with reduced delays in the back line, has resulted in significant improvements. The details are presented in this paper.

Jan 1, 2000

By Thomas E. Brown

Commercd explosives have evolved through this century f?om dynamite through ANFO to the current lines of Water Gels and Emulsions. Water Gels and Emulsions evolved to counter the lack of water resistance and density of ANFO yet maintain its low cost position verses dynamite. Today, explosives must be safe and inexpensive and perform under a wide range of temperatures, function efficiently in wet or dry boreholes and have a good shelf life. Emulsions meet this criterion, which is why they are the current trend products worldwide.

Jan 1, 1998

By P. O'Connell, J. Lever, C. Clemence

The Bulyanhulu Mine, Tanzania is constantly trialing ideas for improvements in the drill and blast process. The project work has resulted in a large number of choices in explosive type and charging methods being available for blast design. Interestingly, though booster sensitive bulk emulsion had been introduced to the site to reduce dilution, better results were being obtained from reduced charge columns (decoupled columns of poured anfo in 50mm pvc pipe) and pneumatically loaded anfo upholes, which had been traced. In order to compare the explosive type and charge up-methods, an explosives comparison trial was performed.

Jan 1, 2006

By Brian W. Stump

"Seismic waves from explosions can be used to characterize physical processes in and around the source. The quantification of absolute levels of ground motion is important for minimizing impact on nearby people and structures. We contrast work in characterizing seismic radiation from contained nuclear explosions with ground motions from multiple explosion quarry blasts. A physical basedunderstanding of the explosion source function allows prediction and extrapolation to new environments where experimental data may not exist."

Jan 1, 1990

By Wilfrid Comeau

This paper deals with the concept of a Quality-Assurance Manual, to the ISO-9001 Level, for quarry blasting in the urban environment. A case history of the incident, which led to its development, is presented in addition to three other case histories. These case histories are related to the potential effectiveness of a well thought-out and applied Quality-Assurance Manual in the conclusions. The basic principle, behind the development of a Q-A manual, is to supply a maximum of quality assurance with a minimum of disturbance to the operation of the quarry. This requires that every intervener in the quarry blasting operations, from management to labourer, be made responsible for the quality of their work. This basic goal can be achieved with a minimum of paper work and added bureaucracy. The manual respects the ISO principle that: Q-A Manuals are not recipe books and should allow for continuing technological developments.

Jan 1, 2003

By Dale S. Preece, J Paul Tidman, Stephen H. Chung

"A discrete element computer program named DMC-BLAST (Distinct Motion code) has been under. development since 1987 for modeling rock blasting (Preece & Taylor, 1989). This program employsexplicit time integration and uses spherical or cylindrical elements that are represented as circles in2-D. DMC-BLAST calculations compare favorably with data from actual bench blasts (Preece et al,1993)."

Jan 1, 1997