Search Documents

By D T. Froedge

To preface these remarks, it is not intended that this paper be a criticism of anyone or any organization involved in drafting the current regulations, for it appears that everyone involved in the process has made an extreme effort to be safe. We wish to show that in this case by making huge safety margins, we have created an unsafe condition in another area. That is by creating vast safety margins in the area of mobile transmitter intensity versus distance scales we have caused a severe handicap in the use of the mobile transmitter in securing blasting areas. The use of these mobile transmitters, which are absolutely essential in clearing areas where there are woods, mountains, or urban structures is virtually eliminated because of the safety factors prescribed in the regulations. We wish to show that these mobile transmitter safety factors are much too great, and can be traded off to increase the margin of safety in the ability to clear blasting areas.

Jan 1, 1975

By Chantale Doucet, Yves Lizotte, Alan Cameron

A joint Federal Government-Industry research project on the effect of geology on the fragmentation of rock excavated by blasting in underground developments was conducted at the CANMET Experimental Mine, near Val d’Or, Quebec. A total of thirteen (13) blasts were studied from November 1994 to February 1995. The analysis of each blast was divided into three stages: pre-blast characterization, including structural mapping, assessment of Rock Mass Ratings (RMR), Tunneling Quality Indices (Q), blast design documentation; blast characterization comprising blast vibration monitoring and analysis; and post-blast assessment comprising fragmentation assessment by digital photoanalysis, calculation of half cast factors and measurements of bootlegs.

Jan 1, 1996

By F O. Otuonye

Full-face blasts were fired in a 12 x 8 ft drift of an underground hardrock mine in a basalt formation with porphyry copper to study the effects of drill pattern and explosive type on the size distribution of the resulting muckpile. Each muckpile produced by five full-face blasts was sampled four times with a scooptram equipped with a 5-cu yd bucket and the size distribution of the broken rock in each bucket was determined by screen analysis. Results show a strong dependence of the fragment size distribution of muckpile on the blast pattern and explosive type for a given rock type. The mean fragment size of the broken rock was compared with the predictive equations of other investigators. Random sampling of the muckpile from full-scale blasts and screen analyses of the samples are recommended in assessing the size distribution of the broken rock because of scaling errors that are inherent in full-scale blasts when designed from results of small-scale tests.

Jan 1, 1985

By Richard J. Mainiero, Michael S. Wieland, Harry C. Verakis

The Bureau of Mines, U.S. Department of the Interior, has been conducting research on delay blasting in underground coal mines in support of the efforts of Mine Safety and Health Administration (MSHA), U.S. Department of Labor, to revise coal mine blasting regulations. Part of the research centered on developing an understanding of the factors that lead to misfires of permissible explosives. Research was conducted to determine whether frequency of misfires was related to borehole spacing. For a wide variety of permissible explosives, misfires were observed for about 50 X of the holes at 45-cm (18-in) spacing. Misfires were also observed for 60-cm (24-in) spacing, but the frequency of misfires was much lower than observed for the 45-cm (18-in) spacing. The Bureau has recommended that hole spacings of less than 60 cm (24 in) be prohibited.

Jan 1, 1986

By Alan Minchinton, Ian Kirby, Jim Chan

It has long been known that successful blasting in soft and hard rock can require the use of different explosives. While choosing an explosive of the right energy density is important, the dynamics associated with non-ideal detonation behaviour play an equally major role. Tuning the energy release rate of an explosive to optimise its blast efficiency can be likened to tuning an internal combustion engine to improve its performance.

Jan 1, 2014

By Kevin Dunfield

The Deltadet System is composed of: The Deltadet II electronic Detonator. A Field Terminal to create, modify or simply execute an existing blasting sequence. The radio remote controlled option is composed of a Base Station to program, calibrate and initiate the EDDs plus a Blasting Box to send commands to the Base Station. Blasting lines to connect the EDDs to the Base Station (100m) and Visual Blast software to create or modify a blasting sequence.

Jan 1, 2004

By W. Birch

The traditional concept of scaled-distance modelling for predicting blast induced ground vibration holds many drawbacks, not least of which is the major effect data scatter imparts on confidence determination. An investigation by the Department of Mining and Mineral Engineering, The University of Leeds, England has resulted in the development of simple but effective method of improving prediction capacity through the reduction of effective error by incorporating individual location response into a scaled-distance model. The work is the product of an l&month blast-monitoring campaign at a limestone quarry situated in North Yorkshire, England. The data, when presented in the form of a scaled-distance model, indicates a typical scenario where a good overall correlation becomes marred by the extent of data scatter. Examination of the individual monitoring locations however indicates that the response of the individual location is an important factor in the explanation of the large residuals. The novel approach thathas been developed incorporates a series of locational site factors which when incorporated into a scaled distance model reduces the effective error and therefore improves prediction capacity. The approach is based on using a standard computer package “spread sheet” on the understanding that these are commonly available on all quarry or home computers. This approach has been validated by comparison with a more rigorous statistics method.

Jan 1, 2001

By Gour Sen, Peter Bellairs

Blasting conducted in rock temperatures greater than or equal to 55°C (13 1 “F) and / or in rock containing sulphide minerals and their oxidation products can result in unplanned detonations. Blasting practices involving the identification of the affected areas together with the use of speciality explosive products and rigorous attention to quality control are required to safely blast in these types of environments. Sulphide dust explosions occur in some underground mines where the primary blast results in a secondary explosion of the sulphide rock dust which propagates some distance from the primary blast area. This phenomena results in considerable damage and the generation of significant volumes of toxic gasses delaying re-entry to the affected area of the mine thereby increasing both costs and safety concerns. The exothermic reaction between ammonium nitrate based explosives and rock types containing partially oxidised sulphides have resulted in numerous high risk blasting incidents. These reactions can occur at ambient temperatures and often result in premature detonations / deflagrations causing a great deal of consternation at the affected minesite resulting in lost production and considerable expenditure to solve the problem. Rock masses at elevated temperatures can also result in unplanned detonations unless appropriate precautions are taken. This paper discusses each of these hazards, cites some case studies and details appropriate generic safe and efficient blasting techniques for each of the above applications using appropriately formulated explosive products.

Jan 1, 2000

By James Ludwiczak

This paper consists of the conduct of a forensic criminal investigation of the components, construction, use, and functioning of two suicide bombs. As the title states, the task was to form professional opinions as to whether the bombs would work, would cause property damage, and would injure or kill. The bombs were created and installed by a defendant in a Federal death penalty case where the defendant’s daughter was killed in a shootout with the West Virginia State Police. The two black powder bombs were placed under the front seats of the defendant’s automobile and were designed to function by the use of a toggle switch connected to the automobile’s cigarette lighter. The forensic work first consisted of an inspection of the remains of the wiring system and bombs at the Bureau of Alcohol, Tobacco, and Firearms Laboratory, in Ammendale, MD. This was necessary to determine and detail the wire diameter and lengths, the lengths and size of the wire used, the type of toggle switch used, the type of containers, the type of rocket motors used to initiate the black powder, the manufacturer and amount of black powder used in each bomb, and the type, wraps, and amount of duct tape used for the construction of each bomb. Using this data, tests were conducted by duplicating the wiring system and the two bombs to insure that the system functioned properly. Each bomb was duplicated and initiated to observe the violence produced when initiated in the open air. Duplicate bombs were placed under the seats of a similar type of automobile and initiated. The purposes of the tests were to duplicate the bombs, to observe the violence of the initiation, and to observe the damages to the automobile produced by the initiation.

Jan 1, 2007

By Rolly Thorpe

Bulk emulsion explosives have been used at surface mines and quarries for many years. Recently, this technology has been adapted for underground use in relatively confined work areas and in smaller diameter blastholes.

Jan 1, 1994

By Gungor Tuncer, Erhan Bakirci, Ali Kahriman, Atilla Ozmen, O. Nuri Ucan, Savas Gorgun

There are several methods for demolition of structures but most of them depend mostly on conventional ways of using machines for breaking and crushing structural elements. However the need for lots of work force, expense and extreme amount of time for demolition, made most of these methods non-popular nowadays. Therefore, trials to accomplish a more economic and less time taking method lasted with the use of blasting. By applying controlled blasting on a suitable structure, the structure can collapse and break down to pieces in very short period of time, with no extra work force and cost. In spite of advantages of explosive demolition, the potential danger of explosives and the damage that the blasting may cause to surrondings, if not controlled properly, made people timid to the method especially in urban areas. Therefore, the pre-assumption by computational analysis has become an essential matter in the process.

Jan 1, 2002

By Donald J. Westmaas, Fred C. Drury

The factors affecting the selection and use of exploisves have changed radically in the past three decades. The objective of this paper is to point out considerations which should now be employed by the Explosives Engineer in his selection and use of modern chemical explosives.

Jan 1, 1978

By Courtney W. Shea, Dennis Clark

Reckless blasting can have tragic consequences: The death of an innocent traveler, the financial demise of a coal company, and even criminal prosecution. In June 1993, a Tennessee coal mining company was blasting to loosen overburden at its surface mine. The mine was located immediately adjacent to the right-of-way of the northbound lane of Interstate 75. The approved permit included special precautions to be taken when blasting in the area closest to the interstate, including monitoring traffic so as to blast when the northbound lane was clear.

Jan 1, 1998

By B Mohanty, R Yang, M Leblanc

A total of 33 blasts in the pillar recovery program at INCO-Crean Hill has been investigated by means of an extensive set of diagnostic techniques. These included, borehole deviation measurements, stope cavity survey, near-field seismics in both rock and backfill, in-hole VOD and fragment size analysis. The 200 mm diameter VCR blasts employed a variety of explosives types (ANFO, slurry and ANFO/Polystyrene) and deck sizes. The objective of the investigation was to control dilution and backbreak through optimal choice of explosive type and charge weight, without exceeding vibration limits in the adjacent backfill or causing significant degradation in fragmentation.

Jan 1, 1995

By Robert C. Fouchard, Gordon Chalmers, David E. G. Jones, Ivana Alilovic, Phillip D. Lightfoot

There have been numerous international instances over the last several years in which pumping emulsion explosives has resulted in accidents, apparently as a result of increased thermal sensitivity under these conditions. The key questions for the explosive industry are (1) what are the parameters that influence the sensitivity of emulsion explosives and, (2) how do these various parameters interact. To address the sensitivity of emulsion explosives to various parameters, a study was undertaken using an accelerating rate calorimeter (ARC) and a heat flux calorimeter (HFC). The effects ofthe addition of ammonium nitrate (AN) prills and different grades of aluminum (Al) on the thermal behaviour of emulsion explosives were determined. Additionally, changes in pressure, atmosphere (inert or oxidizing) and sample vessel material were assessed for their impact on thermal sensitivity. Addition of AN prills, fine granular Al or atomized Al did not affect the onset temperature for exothermic decomposition, so that the maximum “safe” temperatures for emulsions containing these additives will be similar. There were differences in the rates of self heating, however: AN prills decreased the rate of self heating, whereas atomized Al increased it. The emulsion formulations containing atomized Al produced small holes in titanium vessels. This phenomenon did not occur in Hastelloy C vessels, providing a reminder that materials of construction need to be carefully considered for equipment used to manufacture or handle emulsion explosives.. Both ARC and HFC experiments gave lower onset temperatures in air than in argon. We attribute this to oxidation of the oil phase by air. This result is significant for dry-running pumping conditions, where emulsion is heated in the presence of excess air.

Jan 1, 2000

By Gary B. Hemphill

Estimators will agree that estimating for excavation is the most difficult costing task. Equipment costs and production rates are the toughest to determine. The following illustration is a method that can be used for this determination.

Jan 1, 1976

By Ricardo González Dumuihual, Carlos Scherpenisse

A monitoring campaign to record dynamic pressures generated by detonation of a single blasthole was implemented at Barrick Gold´s Pueblo Viejo Open Pit mine (PVDC), located in the Dominican Republic . Pressure amplitudes beyond the dynamic compressive strength of the electronic detonator´s capsules have the potential to damage these electronic devices, generating misfires along with all the associated risks and entailed safety implications. In most instances, misfires generated from high dynamic pressures are a direct consequence of drilling deviations resulting in blasthole distances smaller than originally designed.

Feb 1, 2020

By E. Contestabile, B. von Rosen

Recently, the Canadian Explosives Research Laboratory (CERL) completed its investigation of a truck accident, which involved 18,000 kg of commercial explosives, 13,000 kg of which was ANFO. Over the three years of the investigation unconfined burns of piles of ANFO were performed. In its final phase of the investigation, two burn trials were performed in an attempt to recreate the accident and the ensuing fire, to identify probable mechanisms that led from burning to detonation. Two full-scale tests were performed using complete tractor-trailers. In each test, the trucks were placed in a jack-knifed position with the majority of the explosives located on the ground in front of the trailer. The explosives were placed in a manner to provide maximum confinement and to maximize the possibility of explosion/detonation while remaining as faithful as possible to the perceived accident geometry. The tests were instrumented using thermocouples and video cameras and observations were made on the burning characteristics of the explosives, tractor-trailer and tractor-trailer components. In each test the explosives burned calmly for approximately 80 minutes. There was no evidence of explosion or of unstable burning. The heat caused several truck components to rupture violently. These included the tires, some engine components, the spring brake chambers and possibly the fuel tanks. Of these, the most violent were the truck tires. Although no quantitative data was gathered on rupture violence or fragment velocity, it is speculated that several truck components might produce fragments with sufficient energy to initiate heat-sensitised explosives under favourable circumstances.

Jan 1, 2004

By P. Lozada

The objective currently demanded from controlled blasting techniques is to minimize damage to the remaining rock mass while protecting the integrity of mine walls and ensuring the quality of the fragmented material for easier extraction. Finding this balance represents one of the three main challenges faced by large open-pit mines. They must achieve mine stability by complying with slope designs while also maintaining good results in terms of fragmentation and equipment productivity. The main constraints are related to unfavorable geological conditions, water presence, limited drilling diameters and available explosive products, as well as managing drilling times and blast scheduling, among others. For slope control, in addition to presplitting, blasting designs generally include buffered rows, drilled with smaller diameters, and loaded with fewer kilograms of explosives than production holes. The objective is to reduce the powder factor (kg/t) to minimize the energetic influence on the walls and attenuate damage. However, this often requires using very short charge lengths compared to the bench height (one-third or less) and reducing the pattern geometry, which increases the number of holes per ton and drilling costs. This traditional technique of reducing powder factor in the buffered rows has the main limitation of not being able to distribute the explosive energy throughout the entire column, leading to fragmentation issues mainly in the steaming area. Measurements conducted by Orica in their operations indicate at least a 30% increase in P80 particle size in the buffer zone associated with this condition. To improve energy distribution, techniques such as decking, or vertically decoupled charges can be employed. However, these techniques cannot be applied under wet conditions, and strict control over implementation quality is required to avoid deviations, which increases loading operational times and resource required. In this sense, the use of less energetic and lower-density explosives is a better alternative. On one hand, they allow for complete charge columns in the buffered rows, ensuring homogeneous fragmentation, and on the other hand, they reduce the energetic influence on the slopes, significantly decreasing vibration levels. With less energy per kilogram of explosive (MJ/kg) and less charge per linear meter (kg/m), it becomes possible to handle higher specific charges and longer explosive columns, providing flexibility in drilling and loading design options without compromising slope stability.

Jan 1, 2024

By W. Boas, R. Silva, D. Yumi, L. Steffen

The continuity of the flow and stages within the mining process is essential to achieve success in its operation and results, especially when it comes to a gold mine. During the first seven months of 2022, crushing at the Morro do Ouro Mine had 19 stops in the primary crusher due to equipment blockage/obstruction, this could be due to the size of the material that was blasted with explosives and fed. The feeding of coarse material to the crushing plant impacts the operation in several ways, for example, premature wear of the equipment, reduction in the supply of the remainder of the beneficiation, reduction of the buffer pile and damage to the conveyed belt. In a mine located far from the community, the fragmentation improvement is mainly related to load increments or some other relatively simple change. However, when it comes to a mine located close to communities, alterations of this type must be analyzed in detail, as it can have an impact mainly in relation to vibration and flyrock. Aiming to improve the efficiency of the blasting, mainly in relation to the result of fragmentation, a project was created to improve the efficiency of the blasting with a focus on reducing the crushing stoppage and reducing the amount of material discarded due to inadequate granulometry. During the evolution of the project, several improvement solutions were proposed, for example adjustment of the power factor in relation to the geological characteristics of the rock mass, drainage, blasting geometry, vibration reduction techniques and several operational improvements. By using the techniques and methods identified as improvements during the project, it was possible to observe and quantify improvements in relation to the fragmentation of the blast. During the months of January to July 2022 there were 19 events. It was estimated that at this rate there would be 14 more blockage events, but there were only 3 events and that meant a 79% reduction in blockage. In addition to the reduction in crushing shutdown events, there was also a 53% reduction in the amount of ore that is discarded due to inadequate granulometry and, with that, the feed rate of the grinding system was able to reach the maximum feed limit due to the material being fed to the mill well fragmented, contributing to increase the production and productivity of the beneficiation process at the Morro do Ouro Mine in Paracatu-Minas Gerais-Brazil.

Jan 1, 2024