Search Documents

By Khoi Nguyen, Keeney. Luke

An outcome of geometallurgical mapping and modeling is the generation of continuous down hole profiles of quantitative geometallurgical attributes at assay scale. These attributes vary from traditional routine data collection methods such as assays and geotechnical logging (e.g. RQD, Fracture Frequency), to new measurements including petrophysical attributes, EQUOtip hardness data and modelled estimates of metallurgical performance indices (e.g. A*b, BMWi). Highly variable continuous geometallurgical data with high spatial resolution can make it difficult to identify spatially continuous domains. An automated method based on the well known time series analysis technique of cumulative summation (CuSum) has been developed which uses statistical analysis to identify domain boundaries in down hole profiles. A bootstrap analysis automatically identifies potential domain boundary locations with associated confidence levels and a series of t-tests determine the significance of defined populations. A hierarchical clustering algorithm is applied to results to enable data sensitivity to be taken into account. The method produces statistically significant populations and is suitable for application on either single or multiple drill hole datasets. Domains defined preserve the inherent variability of the continuous down hole data and provide a method for scaling up variability data (i.e. assay interval scale) to mine scale (i.e. bench scale, block model). A major advantage of the method is its ability to provide suitable input parameters for use in spatial modeling of non-additive and non-linear geometallurgical attributes through conditional simulation techniques.

Jan 1, 2014

By C. Y. Sun

Flotation of chalcopyrite and unactivated malachite with xanthates (ethylxanthate, butylxanthate, octylxanthate and dodecylxanthate) is studied in this paper. Minerals interacted with xanthates are detected by FTIR, and simulated by molecular mechanics. It shows that chalcopyrite can be floated with 4 kinds of xanthates, and unactivated malachite can?t be floated with ethylxanthate but can be floated directly with later 3 kinds of xanthates while characteristic absorption peaks of those four kinds of xanthates are all detected by FTIR on chalcopyrite and malachite surface. After simulating the interaction between xanthate and mineral, it shows that H2O and OH-can interact with chalcopyrite and malachite, and their interaction energy may be so called energy bulwark which must be overcome by collector when collector interacts on minerals; the two sulfur atoms in xanthate group interact with copper and neighbor iron atoms on chalcopyrite. It also shows that molecular mechanics results with logP of collectors can interpret the mechanism of xanthate-mineral on atom scale.

Jan 1, 2014

By Victor V. Karmazin

"The appearance of the precise equipment for analysis of results of the laboratory tests with using of the computer processing allows raising accuracy of the estimation of the expected indexes of the mineral processing. Certainly, laboratory tests will not be able to substitute completely industrial ones, but allow reducing the amounts of the industrial tests, that vastly reduces the cost of technological forecast and preparation of data for projection.Calculation of the potential indexes of mineral technology (mass yields and the metal content in products) is fulfilled on the base of results of measurements of the mineralogical liberation parameters using special formulas.The quality of the concentrate ßc = a + ?l • ?s • ?i (ßt - a) can be achieved on a level of the theoretical metal content of a mineral - ßt only if coefficients of mineral processing, of liberation ?l and selectivity ?s of grinding, effectiveness of separation, will reach 1 (a - metal content of the row ore).Increase ?l by overgrinding automatically decrease ?s, and only by destroying of particles of ore along surfaces of accreting of minerals (?i = 1) and when values of all three coefficients will aim to 1, then ßc ? ßt.The degree of liberation of the useful mineral is the ratio of mass of free grains of the useful mineral in the product to general mass of the same mineral in this product. The factor of the liberation, which is defined by curves of dressability by angle of slop of the curve of the elementary faction - ?, is Kr=1 – tga. Kr changes from 0 to 1 when a changes from 45o to 0o. The liberation is reached by grinding of the material, although degree of the liberation, as a rule, is lower than the degree of the grinding."

Jan 1, 2003

By Andrzej Luszczkiewicz, Alicja Bakalarz

The application of new collectors is considered to improve the beneficiation of Polish sedimentary complex copper ores from the Legnica-Glogow Copper Basin (SW Poland), the upgradeability of which becomes more difficult because of ores grade declining. One group of potential collectors is represented by nonpolar reagents. According to the available literature data, only selected sulfides float in the presence of the nonpolar liquids. The paper presents laboratory scale flotation results for the main sulfide minerals occurring in the Polish copper ores applying either thiol (potassium ethyl xanthate) or nonpolar (aqueous emulsion of n-dodecane) collectors. The investigated feed contained 1.91 % Cu in the form of sulfide minerals such as bornite, chalcopyrite, chalcocite and covellite. Other sulfide minerals including galena, pyrite and sphalerite were also present in the samples. Several flotation tests with various doses of each collector were conducted. Mineralogical analyses of flotation products were carried out and the results compared. A comparison of the results indicated that all sulfide minerals floated well with high recoveries ranging from 91 % to 99 % in the presence of the thiol collector. The use of the nonpolar collector provided results in flotation of sulfide minerals with different terminal recoveries from 61 % for chalcopyrite to 100 % for sphalerite. The most significant differences in flotation in the presence of both types of collector under various conditions of upgrading were observed for chalcocite, chalcopyrite and covellite. Similar flotation results were observed for sphalerite and galena for both collectors. The studies confirmed selective flotation of sulfides from the copper sulfide ores of the Legnica-Glogow Copper Basin in the presence of nonpolar collectors.

Jan 1, 2014

By Venkata S. Buddhiraju

Pelletization of iron ores involves balling on a rotating disc to produce wet pellets and induration of wet pellets on a moving grate to produce fired pellets. The quality of pellets produced and the productivity of the pelletization process depend strongly on the characteristics of the feed to the pelletization disc, especially the particle size distribution and the moisture content. The upstream processes involved in the preparation of pelletization feed include grinding, thickening and filtration of the iron ore slurry. The focus of the present work is the closed circuit wet grinding of iron ores. The circuit consists of a primary ball mill, a regrind mill and a hydrocyclone. A population balance model was developed to predict the grinding kinetics and an empirical model was fitted for the separation of fine particles from the coarse particles in the hydrocyclone. Batch grinding kinetics experiments were performed on a laboratory scale ball mill to obtain the ore breakage parameters which were subsequently used for the simulation of the industrial mills. The models were customized for the industrial operations and the effects of different process variables like feed flow rate, water flow rate, etc., on the size distribution of product from the grinding circuit were studied. Additionally, different circuit configurations were simulated to determine operating conditions that could result in the desirable product particle size distribution. The results of simulation were in close agreement with plant observations and the new circuits explored through simulation have helped in identifying potential opportunities for process optimization and control

Sep 1, 2012

By Zhou Yucai, Zhou Jing, Zhu Yimim

"In this article, research on the beneficiation process for a carbon containing copper-molybdenum deposit in Henan province has been carried out. The elemental composition, mineral composition and relative content, characteristics of embedded and symbiotic relationship, the forms of the copper-molybdenum particlesand their disseminated features, and particle size distribution have been worked out. Flotation behavior of copper-molybdenum mixed flotation and separate flotation in the systems of different collectors and depressants, and the influence of different flowsheets on the copper-molybdenum separation have been investigated by actual ore flotation tests, The separation problem of copper-molybdenum for a carbon-containing copper molybdenum ore has been solved.INTRODUCTION In this paper, technological mineralogy, small experiment of flotation recovery of copper Molybdenum ore, and expansion experiment of mineral recovery of copper Molybdenum ore are introduced. (1) The results of process mineralogyshow that the content of copper is 0.42%, molybdenum is 0.021% in the raw ore, they mainly exist in the form of sulfide, with low oxidation rate. (2) The results of flotation tests show that the combination of butyl xanthate and isopropyl ethylthionocarbamate reagents is effective collector of copper-molybdenum mixed flotation for carbon copper molybdenum, (3) When the grinding fineness is -0.074 mm taking 71%, and regrinding fineness is -0.038 mm taking 85%, the flowsheet of first copper-molybdenum mixed flotation and then regrinding rough concentrate and last separation flotation of copper and molybdenum was adopted, which realized the effective separation of copper and molybdenum for carbon-containing copper molybdenum ore. Good flotation indexes were gained with copper concentrate containing 20.96% copper and copper recovery 90.06%, and molybdenum concentrate containing 46.78% molybdenum with molybdenum recovery 72.68%. (4) The seven days average concentration index of scale-up the continuous dressing experiment is as follows, the copper content in copper concentrate is 20.16% and the recovery is 89.61%; the molybdenum content in molybdenum concentrate is 24.58% and the recovery rate is 74.09%."

Jan 1, 2018

By Kaustubh Joshi, Pradip, Beena Rai, Kesri L. Menaria, Venugopal Tammishetti

"Beneficiation of alumina rich iron ore slimes is a major challenge for the Indian iron ore industry. High alumina is deleterious for the performance of both blast furnace as well as sintering plants. Slimes generally contain 5 - 10% alumina, and hence despite assaying as high as 60% Fe, those are dumped in tailing ponds. The slimes are typically less than 37 microns. Selective flocculation of iron ore slimes using highly selective reagents is thus an option worth exploring. Our research is directed at employing state-of-the-art molecular modeling techniques for the selection/design of selective reagents for this separation. We have earlier reported our results on starch as a selective flocculant for iron ore slimes. In this paper, we present our results on the selective dispersion-flocculation of natural iron ore slimes using guar gum flocculant. With careful selection of various process parameters such as flocculant dosage, dispersant dosage, pH and settling time, we were able to obtain a concentrate assaying >66% Fe and <3.5% Al2O3 with an yield of 65 to 68% (recovery of iron values more than 70%) from a natural iron ore slime sample assaying 58% Fe and 7% Al2O3."

Jan 1, 2014

By In-Kuk Bae, Kwang-suk You, Joobeom Seo, Kwanghyun Bea, Hyung-Seok Kim

Arsenic in base metal sulfide ores is highly penalized owing to high costs for its control in metallurgical processing. The arsenic element in the lead-zinc ore, which is target ore in this study, has been shown to be in the form of arsenopyrite. Experimental work in this study is about arsenic rejection flotation, using depressant suitable for the removal of arsenopyrite from the Pb concentrate. The arsenic rejection flotation also included the oxidation treatment of Pb concentrate with H2O2. In this study, the Pb concentrates containing 80.7% Pb and 0.25% as was obtained with the additions of aluminosulfate as arsenic depressant. And through IR measurement, it was also known that the addition of aluminosulfate during arsenic rejection flotation formed calcium aluminosulfate hydrates on the surface of arsenopyrite particle, resulting in rendering arsenopyrite hydrophilic.

Jan 1, 2014

By Steven Wright, Sharif Jahanshahi, Shouyi Sun

"While there is a large industry based on recovering platinum group metals (PGM) from complex sulphide ores containing Cu and Ni, there is little information on the thermodynamics of the matte phase formed on smelting the ore and in particular the behaviour of Pt in the matte.The equilibrium between metallic platinum and industrial mattes was studied in a series of experiments where a small quantity of matte (5g) and platinum foil of 150 µm thickness (0.5 g) were equilibrated in magnesia crucibles at 1400°C under conditions where the oxygen and sulphur partial pressures were controlled.The chemistries of the phases were determined from EDS analysis using a scanning electron microscope. Line scans were initially used to confirm that the foils had attained a uniform composition across their thickness. The composition of the matte was determined from analysis of an area of matte including the small metallic droplets and dendrites.The distribution of Pt in Cu-Fe-Ni mattes (Pt: 1.5 – 3%) and solid Pt alloys (Pt: 54 – 72%) was studied. For a matte of base composition 45%Fe, 11%Ni, 8% Cu, at a base temperature 1400°C, the following behaviour was observed for the Pt distribution ratio:Under the range of sulphur and oxygen pressure of this study (log pO2 from -15 to –12.2, log pS2 from – 4.6 to –2.2), the distribution ratio of Pt between matte and alloy was independent of the sulphur and oxygen pressure, having a value of 0.04.The Pt distribution ratio increased from 0.02 to 0.08 with temperature from 1340 to 1450 oC.For mattes where the proportions of Cu and Ni were kept constant, a slight decreasing trend was shown for the distribution ratio of Pt versus the iron content (37 to 53%) in the matte but was not confirmed because of experimental uncertainty."

Jan 1, 2003

By Felix M. Zhuravlev, Vitalij P. Lyalyuk

"While there is a large industry based on recovering platinum group metals (PGM) from complex sulphide ores containing Cu and Ni, there is little information on the thermodynamics of the matte phase formed on smelting the ore and in particular the behaviour of Pt in the matte.The equilibrium between metallic platinum and industrial mattes was studied in a series of experiments where a small quantity of matte (5g) and platinum foil of 150 µm thickness (0.5 g) were equilibrated in magnesia crucibles at 1400°C under conditions where the oxygen and sulphur partial pressures were controlled.The chemistries of the phases were determined from EDS analysis using a scanning electron microscope. Line scans were initially used to confirm that the foils had attained a uniform composition across their thickness. The composition of the matte was determined from analysis of an area of matte including the small metallic droplets and dendrites.The distribution of Pt in Cu-Fe-Ni mattes (Pt: 1.5 – 3%) and solid Pt alloys (Pt: 54 – 72%) was studied. For a matte of base composition 45%Fe, 11%Ni, 8% Cu, at a base temperature 1400°C, the following behaviour was observed for the Pt distribution ratio:Under the range of sulphur and oxygen pressure of this study (log pO2 from -15 to –12.2, log pS2 from – 4.6 to –2.2), the distribution ratio of Pt between matte and alloy was independent of the sulphur and oxygen pressure, having a value of 0.04.The Pt distribution ratio increased from 0.02 to 0.08 with temperature from 1340 to 1450 oC.For mattes where the proportions of Cu and Ni were kept constant, a slight decreasing trend was shown for the distribution ratio of Pt versus the iron content (37 to 53%) in the matte but was not confirmed because of experimental uncertainty."

Jan 1, 2003

By Peter Ay, Harry Pempel, Satya Narra, Mike Müller, Jens Markowski

"Within the next few years major changes in mobility are expected. Increasing numbers of electric powered cars, electrobikes and E-Scooters define the transport sector. Recently lithium based traction batteries as storage medium have led into matrurity of series production combining high electrical efficiencies with low weights and compact dimensions. Due to the relatively young development with lithium batteries utilization, only few investigation were conducted regarding their recycling. Conventional battery recycling processes can not be applied due to differences in design and chemistry. So an automated disassembly and processing procedure for lithium traction batteries has been developed in the R/D-project ""Li-WERT"". Instead of complete smelting of the batteries without pretreatment, an automated disassembly and specific treatment of the material streams was realised, adjusted to the needs of the subsequent recovery technologies. A higher quality, with reduced expenses for the separation of fine-grained or fused material mixes, can be obtained for the individual components. The automated disassembly using an industrial robot significantly reduces dangers for the operating crew. The selective disassembly and beneficiation allows full recovery of the fractions. The batteries will be disassembled to cell level by the industrial robot. Anodes, cathodes, and separation layers are isolated and processed. The technology is designed, that no waste is generated for disposal. The pelletised cathode coating and the other separated metals (stainless steel, copper, aluminum) can be used in respective metallurgical plants. Circuit boards and plug contacts are also coveted secondary raw materials for reuse. The process is modular and offers high flexibility, e. g. for new battery types/ sizes by quick adjustment of the robot and tool change. Adaptation to other cathode materials (e. g. Li[FePO]) is possible. After finishing the R/D-project, a pilot plant for demontage was realised in 2013."

Jan 1, 2014

By P. Gao, J. W. Yu

"Magnetizing roasting-magnetic separation is an important route for the beneficiation of refractory iron ores. In this investigation, a pilot-scale fluidized magnetizing roasting reactor was introduced and used to study the effects of roasting temperature and the flow rates of reducing gas CO and fluidizing gas N2, on the magnetizing roasting performance of an Anshan-type carbonate-bearing fine iron ore. The results showed that the hematite was almost reduced to magnetite by a gas mixture of 4 m3/h CO and 1 m3/h N2 at a roasting temperature of 540 °C. Under the optimized conditions, a high-grade magnetic concentrate assaying 66.1 wt.% Fe with a recovery rate of 91.2% was achieved from an Anshan-type carbonate-bearing fine iron ore assaying 42.0 wt.% Fe. The XRD, VSM, and optical microscopy analyses revealed that the siderite was successfully converted to magnetite by roasting. Some coarse hematite particles were difficult to reduce to magnetite completely; however, these generated magnetite particles with a fine hematite core could also be effectively recovered by magnetic separation after liberation from gangue minerals due to their strong magnetism. INTRODUCTION Magnetizing roasting followed by low-intensity magnetic separation has been considered as an effective solution, both technologically and economically, when upgrading refractory iron ores (Zhang et al., 2012; Peng et al., 2012; Li and Zhu, 2012). According to the type of roasting reactor, the magnetization roasting can be divided into shaft furnace roasting, rotary kiln roasting, and fluidized bed roasting (Zhu and Li, 2014).Shaft furnace magnetization roasting system is mainly composed of heating and reduction processes. The hematite ore is first heated to 700~800 °C in the heating zone, then falls into reduction zone where the weakly magnetic hematite is reduced to magnetite by coke oven gas at 550~600 °C (Yan et al., 2012). However, several years of engineering practices indicate that the shaft furnace can only process the hematite ores with a granularity of 15 ~75 mm, and the shaft furnace roasting is also characterized by heterogeneity of roasted product. Hence, the shaft furnace magnetization roasting technology is gradually replaced by high-gradient magnetic separation with the development of high-gradient magnetic separator. The rotary kiln generally handles the hematite ores with a grain size of less than 30 mm (Zhu and Li, 2014), however the formation of clinker ring in the rotary kiln will affect the yield of iron resource. In the fluidized bed furnace, the hematite ore is shaken up by an upward current of gas which maintains the individual particles in suspension (Yu et al., 2018). The precise adjustment of the gas velocity to the particle size and the specific weight of the hematite ore, make it possible to generate a floating mixture of gas and solids which behaves almost like a liquid (Yu et al., 2017a). The process is reported to have the following advantages over the other roasting techniques: ease of control due to absence of moving parts within the reactor, homogeneity of roasted products, ability to handle fine particles, and high efficiency of heat transfer and mass transfer (Li et al., 2015; Yu et al., 2017b). However, the simultaneous heating and reductive magnetization of hematite ore occur at the same place in the conventional fluidized bed reactor. Therefore, the reductive atmosphere, as well as the safety and stability of anti-explosion are hard to be controlled. Besides, the roasting temperature for conventional fluidized bed furnace is usually up to 950~1150 °C (Liu et al., 2017). Thus, the formation of clinker ring caused by high temperature will affect the operating efficiency."

Jan 1, 2018

By Markus Dammers, Christopher Robben, Hermann Wotruba, Christian Schropp

"In most underground mining processes the entire extracted ore is transported from underground workings to surface processing plants for separation of valuable minerals and gangue material. Most of the transported material consists of barren rock with negligible metal content, especially for low grade deposits, such as in the copper or gold metal ore mining. Increasing mining depths result in higher costs for transportation and hoisting. Therefore, rejecting waste rock as soon as possible from the material stream gains importance. The concept of resource to product integration in the form of earliest waste rejection in combination with subsequent backfilling follows the philosophy of ‚leaving waste underground?. Implementing mineral processing underground can lead to less required mass movement to surface, hence reducing transportation and hoisting costs. At the same time, rejected waste can be used as backfill to increase extraction rates by reducing pillar volumes. In the mill, a stable high grade feed leads to decreased specific operating and investment costs as well as increased productivity and recovery. These effects as a whole have a large potential to reduce cut-off grades so that resources can be turned into reserves. Within the I²Mine (Innovative Technologies and Concepts for the Intelligent Deep Mine of the Future) project of the European FP7, investigations are carried out by the Unit of Mineral Processing of RWTH Aachen University, the Institute of Mining Engineering I and TOMRA Sorting Solutions | Mining. One aim of the cooperation is to develop new concepts for a comprehensive integration of near-to-face processing in combination with backfill into the overall underground mining process. Effects on up-, down- and side-streams are investigated to prove the potential of resource to product integration in comparison to common underground mining systems and processing methods."

Jan 1, 2014

By F. O. Milovich, V. A. Ignatkina, L. A. Samatova, E. D. Shepeta

"The aim of the research was to increase technological parameters of the flotation of finely disseminated scheelitecarbonate ore using selective reagent regime.In the studies the monomineral fractions of scheelite and calcite; samples of the scheelite-carbonate ore of the Primorsky deposit with the range of the carbonate module 3-65 were used. A carbonate module of ore is the ratio an initial assay of calcite to an initial assay of scheelite. Sodium oleate, iso-decyl alcohol, water glass, calcium chloride, soda or sodium hydroxide as flotation reagents were used. The flotation method in the Hallimond tube and in a mechanical cell, an adsorption method for study the kinetics of adsorption of oleate and isodecyl alcohol and its combinations on scheelite and calcite, IR spectroscopy including ATR to study the composition of surfacecompounds were applied. Selective reagent regime may include two ways - a combination of collectors or a modification of depressants of calcite and other gangue minerals. On one hand the combination of sodium oleate and higher fatty iso-alcohols of fractions C12-C16 in the rough scheelite flotation to reduce the flotation activity of calcite has been studied. On the other hand depression of calcite flotation by calcium chloride with water glass into rough flotation was used; modified the steaming cycle by Petrov's method applying change the concentration of water glass and other. Fatty iso-alcohols can adsorb on the surface of the calcite that reducing the adsorption of sodium oleate and floatability of calcite has been fallen. Their co-adsorbing with oleat on the scheelite surface were support the hydrophobization and flocculation of slime particles of scheelite. Flocculation of the particles of scheelite leads to increased up 3 times of the recovery of scheelite from the slime class, and calcite change up only 1.4-1.1 times it’s recovery.The growth of the carbonate module more than 11 is decreased the assay of WO3 in the scheelite concentrate of selection cycle."

Jan 1, 2018

By Michael. H. Moys, Clayton Bhondayi

An electro-resistive measuring technique developed by the authors was used to study the effects of superficial gas velocity and froth height on froth phase bubble sizes as a function of height above the pulp-froth interface. Flotation tests and the bubble size measurement were carried out in a laboratory mechanical flotation cell that was operated in a pseudo-steady state mode using primary rougher tailings slurry from Lonmin Platinum as feed. The values of intra-bubble impact distances (IIDs) which are the estimates for froth phase bubble sizes obtained from the measurements indicated that as superficial gas velocity was increased, the values of IIDs decreased for the two froth depths tested. Increasing froth height at fixed gas rate resulted in an increase in IID values especially close to the froth surface. Changing froth height and gas rate alters froth residence times; longer froth residence times mean more time for bubbles to coalesce hence larger values of IIDs and vice-versa.

Jan 1, 2014

By James A. Finch, Xiangzhou Ding, Yue Hua Tan

"The Jameson Cell is one of the choices of flotation machine in coal, base metal processing and other specialist applications. This paper determines the effect on vacuum pressure and bubble size of two design variables, orifice size and downcomer length, and the operating variable air-to-water (AWR) ratio. The main findings are: orifice size and downcomer length impact the vacuum but have limited effect on bubble size; AWR < 1 favours high vacuum, conditions are identified where vacuum is maintained at AWR > 1, and water flowrate has slightly greater impact on bubble size than air flowrate.INTRODUCTIONFroth flotation, the most common technique for mineral separation, has been in use for over a century. The process takes advantage of the difference in wettability of mineral surfaces to achieve the separation of valuable minerals from non-valuable minerals, or gangue. Numerous flotation machines have been invented and patented over the years. The Jameson Cell, invented by Professor Graeme Jameson in the late 1980s, is one successful example. First trialed at Mount Isa Mines (Queensland, Australia), Jameson Cells have been installed at operations around the world for the recovery of fine coal (Mohanty and Honakeri, 1999; Cowburn et al., 2006; Hacifazlioglu and Toroglu, 2007; Uçurum 2009), minerals of copper (Farr 1992; Atkinson et al., 1993; Harbort et al., 1997), lead/zinc (Rohner, 1993; Munro, 2003) and gold (Bennett et al., 2012; Lauder et al., 2003), and in water treatment (Yan and Jameson, 2004), solvent extraction de-oiling (Miller and Readett, 1992; Miller et al., 1997; Harbort et al., 2003; Young et al., 2006), oil sands processing (Neiman et al., 2012), and various food industries (Brenneman, 2014). One of the largest units is the 650 cm diameter separation tank with 24 downcomers installed in an Anglo American operation (Osborne and Euston, 2015). Scale up is relatively straightforward: to increase capacity the number of downcomers is increased with corresponding increase in size of separation tank.The Jameson Cell comprises two main parts: a vertical tube (downcomer) which provides self-aspiration and intense bubble-particles contact, and a (separation) tank where particle-bubble aggregates disengage from the pulp. The intense bubble/slurry mixing in the downcomer with air holdups reaching 60% (Marchese et al., 1992) accelerates particle collection enabling the greatly reduced cell volume compared with mechanical flotation cells and columns. The disengagement of the particle-loaded bubbles from the slurry in the separation tank is usually aided by addition of washwater."

Jan 1, 2018

By J. Bouchard, Ali Vazirizadeh, R. del Villar

"The amount of water reporting to the concentrate correlates well with the solid entrainment. It is well known that the frother and collector dosage as well as the froth depth and gas rate influence the amount of water reporting to the concentrate. This is also true for gas dispersion properties such as gas holdup and bubble surface area flux. On the other hand, a positive bias rate, required to reduce hydraulic entrainment, also affects water recovery and thus the particle recovered by entrainment (depending on the their size). Up until now, the effect of the gas rate on the water recovery has been studied, but no comprehensive investigation on the gas holdup, bubble size and bubble surface area flux has yet been reported. This research precisely aims at addressing this issue. The experimental work was carried out under a constant gas flow rate to eliminate the gas volume effect, while other gas dispersion properties have been varied by modifying the frother concentration and the shearing water introduced to the frit-and-sleeve sparger. A constant froth depth and no wash water were used, in order to be able to evaluate the exclusive correlation between the water recovery and the bubble surface area flux and/or the bubble size. It is worth mentioning, that the particle size of the hydrophobic particles did not show a significant effect on the amount of water going to the concentrate. Not surprisingly, experimental results demonstrate that water recovery increases with the bubble surface area flux and with the gas hold-up."

Jan 1, 2014

By Gábor Mucsi, Barnabás Csoke, Viktor Mádai, Zoltán Molnár, Viktor Török, Ádám Rácz

The application of the stirred media mill in dry mode came to the front only in recent years, but at the same time several questions arise, such as aggregation, agglomeration, sticking on the liners and the grinding media. During high energy milling, not only the particle size reduces, but among others, in numerous cases the crystal structure and the amorphous state of the material also change due to the mechanical activation taking place. The present paper deals with experiments carried out on the ultrafine fly ash grinding in dry mode at various grinding conditions in a stirred media mill to investigate the mechanochemical effect and the energy efficiency of the mill. During the experiments the particle size distribution, particle shape, specific surface area, amorphity and crystal structure of the products were examined. The product related stress model was used for the evaluation of the effect of milling parameters on the mechanical activation. It was found, based on the experimental results, that there is mechanochemical effect on crystal structure of fly ash in the stirred media mill, as it was revealed by X-ray diffraction and FTIR measurements. The experimental results made it possible to determine the effect of the rotor circumferential speed and so the stress intensity on the mechanical activation of fly ash could be revealed.

Jan 1, 2014

By J. Yianatos, C. Matamoros, F. Díaz

The non-selective entrainment of fine solids in flotation equipment has a detrimental effect on the concentrate grade. Reduction of solids entrainment (upgrading) is typically related with a loss in recovery of valuable minerals. For improving the froth transport characteristics and flotation cells design, a better understanding and quantification of the actual solids drainage and entrainment processes are required. In this work, the study of solids transport in the froth of a two-dimensional flotation cell was performed. The prototype cell represents a radial section of an industrial flotation cell (130m3) and was operated at steady state. Experimental tests consisted of adding a small amount of radioactive solid tracer (0.3g) near the top-of-froth or near the bottom of froth (close to the interface). The solid was selected as a non-floatable mineral (gangue) in order to evaluate both the solid entrainment into the concentrate as well as the solid drainage into the collection zone. Solid tracer consisted of fine or coarse gangue particles, P80 of 35 and 120 µm, respectively. Twelve collimated sensors located along the froth and collection zones allowed the evaluation of the solid transport in the froth, and the solid drainage from the froth to the collection zone, after tracer addition at different distances from the discharge lip. Results showed that longer distances to the froth discharge lip, as well as higher particle sizes, promotes higher solid drainage from the froth to the pulp zone, while decreasing the solids entrainment into the concentrate. The same result was observed for the solid located near the top-of-froth as well as near the bottom of froth. This information was complemented by the froth surface velocity measurements, using the Visiofroth system, showing a good agreement between the froth bubbles velocity and the solid transport velocity, measured near the discharge lip.

Jan 1, 2018

By S. Gomez, P. A. Bebswa, A. N. Mwale

"The research aimed at improving the way screen performance analysis is conducted using a model that accounts for most feed and design parameters in its formulation. Thus, the aim was to validate the fine screen model that was developed at the Centre for Minerals Research (CMR) unit at the University of Cape Town. Fine wet screening is increasingly becoming an important application in fine grinding operations. Minera Saucito, a lead-zinc Mexican mine has replaced hydrocyclones with eight stacks of five decker derrick screens to close the ball mill in their concentrator plant. The five decker stacks have improved the overall plant throughput by 20% and have had the ball mill circulating load reduced considerably. As a continuous plant optimization process, a number of surveys were carried out to assess the performance of the 75 µm panel aperture installed screens. The surveys were conducted at seven different feed rates to the entire nest of screens to collect performance data. Using the fine screen model to analyze the results, it is found that as the feed rate increase, the sharpness of separation reduces. The CMR fine screen model was fitted to these results. The model fits the plant data with good accuracy. Simulated results based on this model are also presented.INTRODUCTION The potential of high frequency vibrating screens has long been identified as an alternative to hydrocyclones in grinding applications (Rogers and Brame, 1985). However, high frequency vibrating screens have had two main disadvantages, low capacity and high wear rates (Kelley and Mckeon, 2005; Teknikk, 2009). Current vibrating screen technology overcomes these challenges by multiple deck screen design and use of wear resistant urethane materials for panel construction (Kelley, 2007; Valine and Wennen, 2002). For a example, the Derrick screen’s material of construction is a tensionable urethane that provide high open area ranging between 35 to 45% with considerably reduced blinding (Valine and Wennen, 2002). Thus, there has been an increased uptake by the mining industry in the use of wet fine vibrating screens closing the ball mill as the final classification stage in the comminution circuit (Barkhuysen et al., 2010; Frausto, Ballantyne et al. 2017; Pelevin and Lazebnaya, 2009; Teknikk, 2009). Even though there is a number of models in existence, none of these models adequately predict the performance of high frequency vibrating screens (Karra, 1979; Rogers, 1982; Subasinghe et al., 1990; Trumic and Magdalinovic, 2011). Recently Mwale et al., (2016) developed a model for predicting the performance of high frequency vibrating screens using the partition curve properties. The input parameters of the model include screen open area (??) in m2, tonnage feed rate (????) (tph) and the weight fraction of solids (??) in the feed for a given panel aperture size. The model was developed based on data collected from a single deck industrial size derrick screen, in a pilot setup. The work presented in this paper is an attempt to test this model using data collected from Minera Saucito concentrator, an industrial plant whose comminution circuit is shown in Figure."

Jan 1, 2018