Search Documents

By Frank Rausche

Introduction and Background Testing -Pile Preparation -Data Processing -Data Interpretation/Case Studies Case Studies - Existing Piles Stories from around the world

Jan 1, 2001

By John C. Niedzielski, A. Frances Ackerman

The existing US-70 Bridge over the Gila River at Bylas, Arizona is planned to be replaced due to its current poor condition. The replacement bridge is planned to be a 15-span, 1,904-foot (580 meter) long bridge, the third-longest bridge in the state highway system. Within the Gila River floodplain, granular alluvial soil is underlain by cohesive lacustrine soil; bedrock was expected due to nearby terrain but not encountered within the geotechnical exploration depth of 166.5 feet (51 meters) or less. Based on the anticipated loading conditions, design scour depths and the soil conditions, the full structural loads are carried by large diameter drilled shafts; therefore accurately determining the axial capacity of the proposed drilled shafts has important practical and safety implications. The conventional methods for axial capacity determination may be overly conservative to use for design in the site’s layered granular and hard clay soils. An Osterberg cell load test was performed to obtain detailed information on the load transfer from the drilled shaft in side friction and base resistance to allow optimization of the bridge foundation design. The fullscale field test played a significant role in the design of the project’s deep foundations, notably, by incorporating the specific subsoil properties and consequently, an exact prediction of the load-settlement behavior under loading. This paper provides the results of the geotechnical site investigations, drilled shaft load testing procedures, and shaft load distribution from the load test results. Comparisons were developed between predicted axial capacities of drilled shafts using several design methodologies and the axial capacity measured from static load testing. The load test results showed that underestimation of the axial capacity is evident using conventional methodologies. The exact prediction of the load-settlement behavior under loading combined with a site-specific design approach, resulted in a substantial reduction of foundation costs due to reduced drilled shaft dimensions.

Jan 1, 2017

By Michael Perlow

Helical screw piles in use since 1838 are routinely used for energy, transportation, municipal, industrial, marine and coastal infrastructure as well as for excavation support, environmental remediation, and foundation repair. They are especially well suited for work in constrained areas, renovations and structure retrofits. Helical pile design procedures over the past 10 years have gone through a remarkable evolution with the establishment of the 2007 AC358 Helical Pile Acceptance Criteria and inclusion of helical screw piles in the 2009 International Building Code (IBC). New 2009 IBC building code requirements and AC358 Acceptance Criteria are presented along with advances in helical pile design procedures, installation, QA/QC, and recommended load test verification criteria. Use of helical smart piles to validate helical pile design and verification of ultimate pile capacity is highlighted.

Jan 1, 2011

By Derrick Dasenbrock

Two DFI committees independently organized two complimentary panel sessions for the recent American Society of Civil Engineers' (ASCE) Geo- Risk 2023 "Advances in Theory and Innovation in Practice" Conference in Arlington, Virginia, July 23-26. The Geo- Institute (GI) specialty conference welcomed more than 200 professionals and students interested in risk from around the world to the Washington, D.C., area for three full days of plenary keynote lectures, papers and no-paper sessions. The GI Risk Assessment and Management Technical Committee organized the event, which is the third in a series planned on a 6-year cycle. The previous two events were in 2011 in Atlanta and 2017 in Denver.

Sep 1, 2023

By Richard Brink, Eric M. Klein, Kenneth B. Andromalos

"A portion of the roof for a 129 x 144-inch, nearly 100-year-old sewer outfall in the City of Baltimore had deteriorated to the point that it resulted in the development of a large sinkhole in a residential neighborhood. A subsequent video inspection of the sewer outfall indicated that there was a hole in the sewer outfall, and it would need to be repaired . After initial backfilling of the sinkhole and repairs to the water service lines, a conventional wood shoring system was used to support the excavation and expose the Main Outfall Sewer to inspect and repair it. This excavation was unsuccessful because of loose sandy soils and high groundwater conditions. An innovative use of a steel reinforced jet grout excavation support system was ultimately used to underpin an adjacent 20-inch water main and other nearby utilities, and provide access to the top of the Main Outfall Sewer some 22 feet below the street surface to facilitate inspection and repair of the sewer. This excavation support system was also successfully utilized in the final repair of the sewer roof by serving as a buttress for the new roof system.1.0 IntroductionThe project site is located in a residential neighborhood with brick masonry row houses situated on the south side of Chase Street and a brick masonry church on the north side of the street. Figure 1 illustrates the location of the site. The City right of way is 65 feet wide, and the street is 40 feet curb to curb. The centerline of the Main Outfall Sewer runs parallel to and a few feet south from the centerline of the street. Other utilities running parallel to the street include a cast iron 20-inch water line built about 1910, a 24-inch terra cotta storm drain, a 6-inch terra cotta sanitary sewer, a 4-inch cast iron gas line and a 40-inch electrical duct. Cross utilities included a 4-inch gas line and several smaller water and gas service lines to the church and row houses. One gas line that was not shown in the City's GIS database was exposed during the excavation."

Jan 1, 2005

By A. Paviani

The subject of this session is "Equipment Installa­tion, Recent Developments". This is a subject which is not usually addressed at conferences of Foundation Engineering. It is rare to find sessions dealing with the technological side of deep foundations, a subject which only recently seems to have aroused sufficient interest at national and international conferences. It is therefore natural for the subject of "Equipment", or the tools used to implement the various "technologies", to be over­looked or mentioned only occasionally during the discussion of other issues. At conferences, most of the attention is attached to research and to the theoretical interpretation of the performance and behaviour of deep foundations, as well as to establishing the most suitable calculation algorithms and approaches for the study, design and control of foundation structures. It is almost as if the subject of equipment is felt to be less important or, perhaps, that it is considered to belong more strictly to mechanical engineering than to civil engineering.

Jan 1, 1994

By M. Hesham El Naggar, Maged A. Abdlrahem

"Hollow bar micropiles have constructional advantages such as: fast and low-noise and low vibration installation process and small installation equipment, which allow access to tight places. In addition, they have efficient load transfer mechanism, which facilitates carrying considerable load in compression and tension. The common practice is to use diameter ratio of drill bit/ hollow bar (Db/Dh) around 2 in their construction, and they are typically designed assuming type B as classified by the Federal Highway Administration (FHWA). In this paper, the performance and capacity of Hollow bar micropile with different (Db/Dh) ratios are investigated. Full-scale micropiles were installed at a site in Ontario, Canada, and were tested in order to evaluate the uplift performance of Hollow bar micropile with different(Db/Dh) ratios. Two micropiles with two different ratios 2.25 and 3 were constructed and tested. The total length of the micropiles was 6m with embedded length of 5.75m. The soil at the site was primarily medium dense to dense sand. The results of the load tests are presented and discussed. It was found that the uplift capacity of the micropile increased by about 19.5% as Db/Dh increased from 2.25 to 3.INTRODUCTIONMicropile is a small diameter, less than 300 mm, drilled and grouted pile and is typically reinforced according to Federal Highway Administration (FHWA, 2005). The technology of micropile was introduced in North America in 1970’s, but the growth in the east coast of United State was intense compared to all other cities around the globe (Bruce and Nicholson, 1989). Nowadays, micropile construction is used extensively worldwide as a viable solution that offers several advantages such as fast installation in low headroom, minimal disturbance to the adjacent structure efficient load transfer due to high grout to ground bond strength. As the method of grouting has major influence on the grout – ground bond strength, FHWA has classified the micropiles into four categories. Type A: the grout is placed under gravity and no pressure is required. Type B: The grout is typically pressurized under a pressure range from 0.5 to 1 MPa as the temporary casing is withdrawn. Type C: the grout is placed in two-step process. First, the grout is poured under gravity only as in Type A. Before the hardening of the grout, similar grout is pressured of at least 1MPa without the use of packer. Type D: Like Type C, it is a two – step process, the grout is placed under gravity as in Type A and sometimes pressurized as in Type B. After hardening of the initial grout, additional grout is pressurized between 2 to 9 MPa through sleeved pipe by using packers, as many times as needed. According to this classification, hollow bar micropile is usually designated as Type B. However, the construction technique is completely different from Type B. Recently; there is a trend to supplement the four types of micropiles by Type E as represent to hollow bar micropile (Timothy et al, 2012). The construction method of hollow bar micropile involves two main stages which can be performed in one–step process: advancing the drilling bit attached to a threaded hollow bar to the required depth; and pressurizing the grout through nozzles of the drill bit."

Jan 1, 2016

By J. P. Burland

The paper describes a number of recent case histories in the United Kingdom where field instrumentation and measurements have played a major role in the design and construction of excavations, piles and foundations. It is shown that the design and construction procedures for deep excavations in London Clay are based almost entirely on the results of field measurements. Examples are given of successful application of such measurements. The present understanding of the behaviour of bored piles in stiff clays and their design is based on a number of instrumented pile loading tests. The results of these tests have led to a radically new concept of pile design in which the piles operate at their full shaft capacity under working loads thereby resulting in considerable savings in design and construction. Some examples of the successful application of this concept are given. Finally it is shown that the present knowledge of the stiffness properties of chalk is based entirely on field observations. An example is given of how direct field measurements were used to solve a foundation problem at the base of a coffer-dam in chalk.

Jan 1, 2010

By Omer F. Usluogullari, C. Vipulanandan

"It is critical to monitor the ground conditions during excavation and drilling of boreholes during construction to identify possible changes in the soil and rock formations. Drilled shafts are increasingly used as foundations to support structures, bridges and other facilities in geomaterials such as soft-rocks and hard clays. Locating the bottom of the borehole during construction with the required design strength is critical. Hence developing a simple device that could be easily adapted/used with the drilling tool was of interest in this study. Determining the shear strength of the geomaterial in the borehole and at various elevations including the bottom of the borehole can lead to better quality control of construction by identifying the various layers based on strength.In this study, a down-hole penetrometer (DHP-CIGMAT) was designed, built, calibrated and tested in the field to determine its effectiveness in measuring the strength of soil/soft rock in the boreholes. Based on limited field tests, linear correlations between geomaterial strengths and DHP-CIGMAT deflection have been developed. The DHP-CIGMAT can be used to identify soils and soft rocks.IntroductionIn-situ tests are increasingly used to determine the soil properties for geotechnical analysis and design of deep foundations (Ampadu and Arthur 2006; Hsu and Huang 1999). Static and dynamic penetration resistances have been used to classify and characterize subsoil (Ahmadi et al. 2005). The penetrometers evolved from the need of acquiring data on subsurface soils that could not be easily sampled by any other method. Laboratory testing undisturbed samples requires great care to avoid disturbance during handling, or systematical disturbance during testing, and it may be difficult to relate the laboratory test results to the in-situ properties of the soil (Sanglerat 1972). There is always a certain degree of disturbance to the samples because the confining pressures, which exist in the ground, are forcibly changed when the sample is collected."

Jan 1, 2017

By Matt Fenwick, Douglas R. Schwarm

Stringent underwater noise limits at the Fairview Ave. N. bridge replacement on Seattle's Lake Union required an innovative approach to supporting the 470-ft long drill trestle. Screw-in foundations would reliably mitigate noise, but the required 500-kip bearing resistance were an order of magnitude higher than typical helical piles. This paper describes the process of designing, installing, monitoring, and testing 22-inch dia. helical piles 80 feet long with 36- and 42-inch dia. helices. A static load test confirmed that the conventional k-factor design method can be extended to capacities of up to 800 kips. A 375 ft-kip drive mechanism had to be fabricated because no North American equipment could supply the necessary installation torque. Real time installation monitoring and later "re-torque" tests confirm that helical piles gain capacity with time, analogous to driven piles under restrike. Underwater and on-land measurements confirmed very low noise, suggesting the possibility of widespread adoption where similar limits are imposed. Overall, this case history illuminates the need for innovative deep foundation types in response to ever-increasing regulatory constraints.

Sep 8, 2021

By Michael A. McNicholas

"Deep foundations utilize the varying soil conditions to provide the most cost-effective or practical scope for a given jobsite. Once the scope has been determined and the engineering applied, the element can be installed and tested to determine if it is suitable. QA/QC programs are vital for the assurance that the element designed by the engineer has not only been properly constructed but that the design assumptions are confirmed. The two deep foundation elements referenced are drilled displacement piles (DDP) and micropiles. Each of these elements allows for large loads to be distributed deep into the subsurface geology. Having the technology and ability to monitor the tests in real-time can be beneficial to a contractor in determining if the design is adequate or if adjustments need to be made on future piles. The proper QA/QC guidelines for installation and monitoring need to be in place to ensure that an accurate interpretation can be made on the pile. This paper discusses the typical testing and the positive results that the author has encountered using the latest advances in strain analysis.KEY TERMSDrilled Displacement Piles:A deep foundation system that has the ability to shed load into the geology through shaft resistance as well as tip resistance, similar to drilled shafts. This pile element is unique in that it has a consistent pile section and thus a consistent modulus of elasticity.Micropile:A deep foundation system used in applications where the foundation lies over material not suitable for a spread footing and the ideal soil stratum is deep below the foundation. Micropiles will have two different cross-sections consisting of a cased section and an uncased section. For this reason, this pile type requires additional analysis when computing stress-strain relationships.Geokon Strain Gauges:Instrumentation such as Models 4911A-4911 Vibrating Wire Strain Gauges ( known as Sister Bars) are designed to be embedded in grout and calculate loads based on the change on grout strain over a period of time.Stress:A pile element is under a compression (axial loading) load when a force acts along its axis and is normal to the plane of the section. The corresponding stress the pile is experiencing is described as a normal stress. The stress is obtained by dividing the magnitude of the load distributed over the cross-section by the area of the pile cross-section, as shown in Eq. 1."

Jan 1, 2017

By Kazunori Matsushita, Masaru Sakakibara, Kenji Harada, Naotoshi Shinkawa, Mitsuo Nozu

The Sand Compaction Pile (SCP) method has been widely used as a typical countermeasure against liquefaction in Japan, and its effectiveness has been confirmed in many case histories of damages caused by the past large-scale earthquakes. A series of studies were conducted to evaluate the effectiveness of the compaction method and other factors, if any, in sustaining a seismic force that is greater than the assumed one and caused no damage. Based on the results of these studies, the Architectural Institute of Japan (AIJ) has indicated in its “Recommendations for Design of Ground Improvement for Building Foundations” published in 2006 that the liquefaction resistance ratio (tl/sz) of the composite ground, which consists of sand piles and surrounding compacted ground, is higher than the RL calculated by using the SPT N-values of the ground in-between the sand piles. In this paper, statistical analysis of safety factor against liquefaction, FL, was performed by using the SPT N-values of ground in Port Island and Rokko Island which were both fully reclaimed islands in Kobe city during the 1995 Hyogo-ken Nambu Earthquake (classified as intense shaking) and, together with the consideration of relative settlement, resulted in tl/sz of the composite ground being 1.5~2.5 times of tl/sz of the soil in-between piles after improvement. Furthermore, the liquefaction resistance curve of SCP-improved sites obtained from the relationship between SPT N-values and cyclic shear stress ratio during the 2011 off the Pacific Coast of Tohoku Earthquake, which was regarded as long-duration earthquake, was plotted to the left side of the curve originally proposed by Japan Road Association. Thus, the liquefaction resistance of the improved ground was found to be higher than that of the natural ground, even for the same SPT N-values, verifying the validity of the AIJ recommendation.

Jan 1, 2017

By Nick O’Riordan, Kaitlyn L. Fleming, Michael Riemer, Youssef M. A. Hashash, Stephen McLandrich, Mohamad Jammoul, Pierre Gouvin, Andrew Yeskoo

"To accommodate urbanization, cities are developing more underground space as a means to house public transportation systems and other entities. Underground developments often require construction of deep excavations in an environment dense with infrastructure. The success of such a project is related to the amount of impact imposed on adjacent structures and economic activity; impact should be limited to insignificant amounts in order to mitigate damage and disruption. Thus, large-scale urban construction projects require extensive monitoring of ground movements and installed support performance to facilitate informed decisions for adjustment of construction activities and support design when necessary.In downtown San Francisco, a unique large-scale excavation in saturated soft soils was constructed for the Transbay Transit Center (TTC). Construction of the excavation began in April 2012 and was completed almost two years later in February 2014. To monitor ground and structure response to construction, the project team used an extensive instrumentation network that included automatic inclinometers, piezometers, strain gages and total stations paired with survey markers. Innovative imaging techniques developed a record of construction in order to relate measured deformations to construction activity.Transbay Transit CenterThe Transbay Transit Center (TTC) is being constructed as a modern day transportation hub in downtown San Francisco to replace the former Transbay Terminal. The project is located in the South of Market area, less than half a mile from the San Francisco Bay. The final center will connect eight counties in the Bay Area through 11 different transportation systems, some of which will be housed in the TTC including Caltrain, Golden Gate Transit and California High Speed Rail. The aboveground structure will consist of two levels for retail and a third level with a bus terminal beneath a rooftop garden. There will be two subgrade levels to serve as a lower concourse and the train platforms. This structure required construction of a deep excavation closely surrounded by buildings and roads in an area thriving with economic activity."

Jan 1, 2015

By Timothy C. Siegel, Derrick Dasenbrock, Rich Lamb, Paul J. Axtell

"The axial resistance provided by deep foundations may be divided into two components: side resistance and tip resistance. The direction that the side resistance acts depends on the relative movement between the deep foundation and the adjacent soil. That is, when the foundation moves downward relative to the soil, then the side resistance is positive and acts upward. Conversely, when the soil moves downward relative to the foundation the side resistance is negative and acts downward. Research supports that both positive side resistance and negative skin friction develop in essentially all deep foundations. The side resistance distribution is a function of the soil strength and stiffness, the applied top loads, and whether the top load is sustained, transient, or a combination of sustained and transient loads. Consideration of drag load and downdrag has become more convoluted with implementation of geotechnical aspects into the AASHTO LRFD Bridge Design Specifications and its use of load and resistance factors. This paper examines the current AASHTO Specifications and presents an alternative design approach for drag load and downdrag using the LRFD framework. The alternative design approach is illustrated by two examples involving drag load and downdrag.IntroductionThe axial resistance provided by deep foundations may be divided into two components: side resistance and tip resistance. The direction that the side resistance acts depends on the relative movement between the deep foundation and the adjacent soil. That is, when the foundation moves downward relative to the soil, then the side resistance is positive and acts upward. Conversely, when the soil moves downward relative to the foundation the side resistance is negative and acts downward. Research supports that both positive side resistance and negative skin friction develop in essentially all deep foundations. The side resistance distribution is a function of the soil strength and stiffness, the applied top load, and whether the top load is sustained, transient, or a combination of sustained and transient.Consideration of drag load and downdrag has become more convoluted with implementation of geotechnical aspects into the LRFD Bridge Design Specifications and its use of load and resistance factors. This paper examines current LRFD design specifications and presents an alternative design approach for drag load and alternative design approach is applied to several examples where drag load and/or downdrag may control design."

Jan 1, 2015

By Paul A. O’Brien, Gary A. Chapman, Thomas G. Cuniowski

"The new Amcor B9 paper mill in Botany, NSW, Australia, involved the design and construction of a new paper mill founded within the Botany Basin Sediments. There were numerous design and construction challenges to address, including tight settlement tolerances for the paper machine footings (6 mm total and 1/2000 mm differential limits), high variable and cyclic loads, deep (>25 m) bedrock and uncontrolled fill material across the site. The mill structure design incorporated a deep driven precast and CFA piled foundation solution, with a comprehensive swathe of testing to validate pile capacity and expected settlements. The pile design for the mill structure included the installation of approximately 1000 piles, with pile testing comprising dynamic testing and a static load test on precast piles. With consideration of Sydney’s increasing demand for development space in relative close proximity to the city’s CBD, industrial areas in the Botany Bay area are likely to make way for heavy or complex commercial and residential structures. Therefore, a better understanding of the engineering behaviour of sediments underlying these areas would allow for efficient foundation solutions. This paper presents a discussion on effective foundation testing techniques and the effects that the behaviour and characteristics of the Botany Bay sediments impose on deep piled solutions.2 PROJECT DETAILS2.1 New paper millThe project involved the construction of the largest recycled paper machine in Australia. The paper machine is 330 m (1080 ft) long, 22 m (72 ft) high, and capable of producing 1.6 km (1 mile) of paper per minute. Construction commenced in early 2011 and new paper mill officially opened in early 2013. The early works contract was awarded to Baulderstone Construction Pty. Ltd. (Lend Lease Corp. Ltd.), with the D&C contract awarded to a consortium headed by Leighton Contractors Pty. Ltd. (CPB Contractors Pty. Ltd.), which included Golder Associates Pty. Ltd. as the geotechnical designer and reviewer.2.2 Site history and effect on local topographyThe site has been used as a paper mill since 1902, and as such, has layers of uncontrolled fill and buried objects within the upper fill materials associated with historical industrial use. The fill material generally comprised of loose and very loose sands, with isolated pockets of cohesive materials, peats, pulped paper and general construction waste. In addition, during construction, underground storage tanks were identified at depth, indicating the historical extent of filling across the site was extensive. The presence of this generally uncontrolled fill was a factor for determining that the most cost effective foundation solution for the paper mill was piled foundations, to bypass these materials."

Jan 1, 1900

By Alexi J. Neill

"This presentation will showcase two challenging projects with deep excavation support systems in the Atlanta area where state-of-the-art instrumentation and monitoring systems were used to manage risk by confirming design performance requirements / calculations during construction. The instrumentation and monitoring system successfully reduced risk by recording real-time data on a project website while simultaneously sending email alarms to key site personnel when data exceeded pre-determined alarm thresholds. The monitoring data revealed unexpected performance at an early enough stage so that contingency plans could be engaged and remedial efforts devised in order to limit the consequences. Finite element analysis was used to model deformations, analyze the unexpected performance, and prepare theremedial design.INTRODUCTIONConstruction in densely populated urban areas is becoming more common in order to keep up with the increasing infrastructure demands of our growing population. America’s big cities continue to outpace the overall nation in population growth. The city of Atlanta, the nation’s ninth largest city based on metropolitan population, is a prime example of this. The population has grown at a rate of 6.6% between 2010 and 2013, nearly triple the overall growth rate of the United States during the same period (SustainAtlanta, 2015).As a result of increasing infrastructure demands in Atlanta, developers are now constructing larger buildings on smaller properties. In addition, developers are attempting to maximize space on their selected properties, often by designing underground parking garages to accommodate as many cars as possible on these compact sites. In some cases the selected sites are adjacent to buildings, utilities, and other existing structures. The risk associated with construction increases during underground work that requires a support of excavation system, particularly on confined sites adjacent to existing structures. There is a risk posed to people, property, and the environment that the project team should monitor when constructing in these conditions."

Jan 1, 2016

Jan 1, 1997

By John S. Civetta, Seth Martin, Marc J. Gallagher, Arthur J. Alzamora, Ronald Peralta

The Crown Building, built circa 1921, is a 26-story iconic building located at West 57th Street and Fifth Avenue in the heart of Manhattan. The paper highlights collaboration between the geotechnical engineer and foundation contractor to develop economical and practical solutions to foundation design and construction challenges associated with this complex redevelopment project. The project includes both below-grade and above-grade expansion of the occupied building, and required undermining the existing foundations, and essentially doubling the foundation loads. The below-grade expansion required surgical foundation work including drilling minicaissons, shoring columns, underpinning, and excavating 20 feet of rock.

By Carlandrea Albonico, Salvatore Miranda

The paper describes an innovative geotechnical engineering solution that has been provided within the scope of the Galataport Project, in Istanbul, Turkey. Among all interesting geotechnical works included in the Project, this paper presents the design principle, adopted technologies and performance controls related to the Multi- Purpose Bottom Plug (MPBP). This original geotechnical engineering solution has been employed for the deep basement excavation in Karaköy and consists of a combination of seepage control, ground improvement, and load bearing elements, which have been executed with double-fluid jet grouting, pseudo-elliptical jet grouting and permanent micropiles, respectively. The paper highlights the importance of employing cutting-edge technologies within the foundation engineering field and state-of-the-art electronic control devices, in parallel with the essential human expertise, in order to obtain the desired results in this high-profile Project.

Nov 1, 2022

By Damir Dedic, Wörle. Patrick

"Soil properties within a construction project area are analyzed during the planning phase. However, it is only possible to achieve selective soil exploration, even in the case of very extensive investigatory programs, which results in a certain soil risk and uncertainties for planning and execution.Therefore, the application of monitoring systems is becoming increasingly important in the field of geotechnics. The application of suitable monitoring systems for these particular purposes provides considerable knowledge relating to the load bearing behavior of the soil and the ground anchor. Applications that present major challenges to measuring anchor forces include back-anchorages of long-lasting and very deep construction pits, construction pits in urban areas, slope and embankment supports for track and vehicular routes, port and lock structures, and uplift control. Apart from overseeing individual construction stages, monitoring systems analyze the interaction between the soil and structure throughout the latter’s entire life cycle and safeguard the functional capability of the applied system components. Geotechnical construction projects can be adapted, optimized and carried out with enhanced safety from the information obtained.Conventional Monitoring SystemsThere are numerous approaches for determining anchor forces of bar or strand anchors. Lift-off tests and measurements with load cells are the most common methods.Lift-off Test: Lift-off tests provide a possibility to monitor the prevailing force in strand or bar anchors. The entire anchor head structure is lifted using the appropriate equipment. The steel tendon is prolonged, or in the case of strand anchors, a screw-on cap holds the wedge carrier so that a tensioning jack can be mounted above it. Then, the tendon is prestressed until the lower anchor nut (bar) or wedge carrier (strand) is lifted off from the anchor plate. The intersection of the two straight lines in the figure represents the force at which the anchor nut or the wedge carrier lifts off from the anchor plate. Thus, the intersection displays the actual load of the anchor. This form of anchor force control gives conclusive results, but at the same time requires extensive accessories and extra personnel to execute the test. For this test, a sufficient bar overhang must be available, the wedge plate must possess an external thread, or there must be a strand overhang of at least 24 in (60 cm). Furthermore, the anchor head must be freely accessible and in a position to be reached with the necessary equipment."

Jan 1, 2017