Search Documents

By Charles Roeder, Amy Leland, Dawn E. Lehman

Concrete filled steel tubes (CFSTs) are composite members that are commonly used in many countries today. CFST components are used in the United States, but they are more common in Asia, in part because the connections used in Asia are quite labor intensive and there are not standard connections in the U.S. In addition, US design specifications are prepared by separate groups for structural steel and reinforced concrete structures and so composite systems that use CFST components are not overseen by a single group and as such there are several, conflicting design standards. In the US, steel tubes used for CFST are more slender (i.e., the diameter-to-thickness, D/t, ratio is larger) than some other countries, and labor practices (structural steel labor is different than reinforcing steel labor) also cause potential conflicts in construction. As a result, CFST has had some use in tall building construction in the US, but very limited use in bridge construction. A research program at the University of Washington has been in progress to address many of these issues with an eye towards universal design expressions, simpler, standardized connections and promotion of accelerated bridge construction (ABC). The research has resulted in recent changes to the American Association of State Highway Officials (AASHTO) bridge design specification as well as state departments of transportation (DOTs), which supports the increased use of CFST in bridge pile and drilled-shaft foundations. An experimental research study which investigate the flexural strength, shear strength and connections was conducted. These connections provide good performance under both seismic and gravity loads and address the concerns of US construction. These connections, their design rules and requirements, and their impact on composite behavior and system performance are discussed. These results permit rapid and economical construction of CFST bridge piers, piles and drilled shaft foundations. They encourage the use of more slender and economical tubes, while achieving the benefits of composite construction. INTRODUCTION Concrete filled steel tubes (CFSTs) are widely used for bridge and building construction in Asia, but the use of CFST in bridge construction is limited in the US. The historical use of structural steel and reinforced concrete in US bridge construction have resulted in more developed design expression for those construction methods, which has limited the use of CFST. Bridge construction in the US is inherently different than in Asia because of differences in codes, labor costs and construction practices. As a consequence, design and construction practices that are economical and practical in other countries may not be practical for US bridge construction.

Jan 1, 2019

By Nicholas P. Gura

This paper presents the analysis, design, and load test program results for drilled shafts to support a 70-story hotel tower and associated 10 story podium structures located in Las Vegas, Nevada. A mat foundation for the structure, although feasible, would have produced undesirable differential settlements within the high rise tower footprint and at the interface with adjacent lower level podium structures. The resulting foundation system solution for the 70-story, approximately 800-foot long hotel tower was four-foot diameter drilled shafts, extending 100 below shaft cutoff. The design compression capacity for the four foot diameter drilled shaft was 5,000 kips. The load test program proved that the unique Las Vegas valley geology lends itself to efficient installation, precluding the need for engineered slurry or casing. The load testing program included the installation of two four-foot diameter test shafts to 100 feet below theoretical cutoff and the performance of two highly instrumented independent Osterberg load cell tests with maximum sustained test loads of 12,000 kips. Sonic caliper testing was also performed to document actual in-place shaft diameters and verticality. The load test program also provided information necessary for the foundation design of the podium structures. In addition to the tower?s drilled shaft load test program data, continuous flight auger (CFA) pile evaluation and testing was also performed. The CFA testing consisted of traditional ?top down? loading techniques and was performed as an alternative to the recommended shallow drilled shafts for the lower level podium structures. The results of the CFA test program provided supplemental, insightful soil friction data which was used in conjunction with the drilled shaft test program data in evaluating the most appropriate support for the lower level structures.

Jan 1, 2007

By Lucian L. Bogdan

"SummaryActive loaded strand anchors are often used for slope stabilization, retaining walls or tiedown anchors. Normally, strands are tensioned against the structure and wedges are locked inside the anchorages at a certain lock-off load. During the life of the structure, anchors can receive additional loading during a surcharge, seismic event or other activity on the structure.In order to have a reliable ground anchor system, the strand must not slip through the anchorage wedges during its service life. Strand slippage has been reported during lock-off, when dirty wedge plates and wedges have been used. Low lock-off loads are believed to contribute to strand slippage too. Since the initial lock-off load for a ground anchor is usually lower than the lock-load for an equivalent capacity tendon in other types of post-tensioning construction, there is a concern that strand slippage may occur if the load on the anchor increases above the initial lock-off load.Corrosion protection grout, placed after the anchor is locked off, fills the pocket and surrounds the strand and wedges. Some anchor installers believe that the grout will prevent the anchorage from developing additional capacity if the load increases above the initial lock-off load.The load-carrying capacity of an anchorage depends on several factors. Most important are: initial applied load, anchorage geometry, friction between wedge-anchorage-strand and condition of the contact surfaces.The ADSC Anchored Earth Retention Committee considers that the industry should know how wedges behave once the permanent strand anchors are stressed and grouted inside the transition pipe, between wedges and inside the grout cap."

Jan 1, 2005

By Chris M. Haberfield

The design of side resistance of drilled shafts socketed into rock has traditionally been empirically based on the results of pile loading tests in which the side resistance can be isolated from the side resistance. In practice, this is achieved in one of several ways : loading the pile in tension, using a collapsible base, or by using a device such as an Osterberg cell to load the pile from the base. Although this approach has resulted in generally safe design practice, this has been at the expense of efficient design practice. Safety in design has been achieved through conservatism, which has been necessary because of the large scatter that is evident in the pile socket resistance database (Rowe and Armitage, 1984; Kulhawy and Phoon, 1993). Research at Monash University through the 1980's has been aimed towards understanding and then modelling the complex mechanisms of shear transfer at the concrete-socket interface of sedimentary rocks. Armed with such an understanding, the important factors which affect the strength of pile sockets can be isolated, and the reasons for the large scatter can be deduced. This paper briefly describes the research approach taken, and the main features of the design method and computer program which have now been developed. Some load-settlement predictions of the program are compared with the results of full-scale pile socket tests. The paper then presents the results of a numerical study which relates predicted socket a factors to unconfined compressive strength of the rock, socket diameter, initial normal stress and socket roughness.

Jan 1, 1996

By W. Morgan NeSmith

"The DFI ACIP Pile Committee, in conjunction with the Florida DOT, completed an ACIP Pile installation monitoring and performance test program in late 2016 to advance the inclusion of ACIP piles in future specifications for bridges by state agencies. Piles of different diameters were installed for compression, tension and lateral testing, and one pile was extracted for visual inspection. This paper presents the pile installation, non-destructive testing and load test results of the program.INTRODUCTION The Deep Foundations Institute (DFI) Augered Cast-In-Place (ACIP) Pile Committee performed a ACIP pile installation and test program in the fall of 2016 to demonstrate a fully monitored installation of 18-in and 24-in diameter ACIP piles. The program included automated and manual installation monitoring, Thermal Integrity Profiling, compression, tension and lateral load testing (including monitoring of strain gages embedded along the compression pile shaft), and post-testing extraction of an installed pile for visual inspection.PROJECT DETAILS AND FIELD EXPLORATION A general program location map along with an aerial view of the property in Okahumpka FL is shown in Figure 1. Two Cone Penetration Tests (CPT) were performed at initial reaction pile locations R-6 and R-8 (Figures 2 and 3) The results from CPT R-6 indicated very loose soil conditions at depths below 55-ft, indicating potential relic sinkhole conditions. The test layout was subsequently rotated and moved south of CPT R-8.TEST PILE INSTALLATION DETAILS Seven piles were installed to either 40-ft or 60-ft below grade. Thermal Integrity Profile (TIP) wires were installed in all piles but varied to include one wire each attached to a steel center bar or one wire attached to the steel center bar AND four additional wires (each) attached the steel reinforcing cage installed in these piles. Additionally, the 24-in lateral and compression piles had four steel or PVC casings installed next to the TIP wires for testing by thermal probe and/or wire inserted into the casing."

Jan 1, 2017

By Charles M. Wilk

"Mass stabilization (MS) is a ground improvement technique that can prepare areas of low bearing strength soil for subsequent infrastructure development. The technique involves mixing binding agents such as portland cement, fly ash, slag, or lime into the subject soil while the soil remains in-place (insitu). The binders “cement” the soil grains together to form a cement modified soil or a soil cement. The MS-treated area now has improved bearing capacity to support infrastructure or to prevent movement of the material such as landslides.The same insitu soil mixing technique can be used to address contaminated areas. Binders or reagents are mixed into soil. The treatment protects human health and the environment by immobilizing hazardous constituents within the treated material. When used for the purpose of environmental remediation the technology is called Insitu Solidification/Stabilization (ISS).Both Mass Stabilization and ISS treatments require laboratory studies to develop a mix design of soil and binder(s) that produce the desired physical and/or chemical properties. The mix design is then transferred into the field. Successful MS and ISS treatments rely on reproduction at full-scale of the mix design and the thorough mixing attained at laboratory scale. Fifty to 70% of the cost of a MS or ISS project is in the cost of the binding agent that is to be mixed into the subject soil. Under-dosing, overdosing, non-thorough mixing, and mixing in the wrong areas all create cost over-runs.This paper will discuss recent innovations in mass stabilization systems that improve the cost effectiveness of the treatment technology. Specialized equipment can impart greater mixing shear thus improving the thoroughness of mixing. Dry powder pressure feeders can conserve the “drying capacity” of binder resulting in higher strengths at lower binder dosages. Global Positioning System (GPS)-based systems can guide the mixing operator for complete mixing coverage. An integrated tracking and feeding system can record that proper dosing and mixing was accomplished and generate construction QA/QC reports for the client.INTRODUCTIONNew or expanding infrastructure projects may encounter areas of low bearing capacity soil or areas where marginal materials such as waste, dredged material, or sediment have been placed. Mass stabilization is a geotechnical method that can be used to improve the bearing capacity or stiffness of soil. Mass stabilization involves mixing binding agents into soil subject to treatment while the soil remains in-place or insitu.Mass stabilization technique can also address contaminated soil therefore, the same technique can be used to attain both civil and environmental engineering goals. In this environmental application the technology is known as insitu solidification/stabilization (ISS). ISS protects human health and the environment by immobilizing hazardous constituents within the treated material."

Jan 1, 2015

By Harald P. Ludwig, Matthew J. Niermann

The support of excavation (SOE) for the Capitol Crossing project in Washington, DC consisted of a combination of soldier piles, lagging, tiebacks, braces, underpinning, single auger soil mixed (SASM) walls, micropiles, and a tiedback slurry wall. Over 130,000 square feet of SOE was installed with more than 1,300 tiebacks providing lateral support for excavation depths of up to 72 feet. Several structures including the Holy Rosary Church, the Bell Tower, the Casa Italiana, and a modern office building were supported by a combination of conventional hand dug underpinning pits, bracket piles, and stiff SASM walls. This paper will focus on the design and performance of the SOE adjacent to the Holy Rosary Church and the Bell Tower. Deflection-based design was used to estimate the movements of and limit damage to these structures. An extensive monitoring program was used to provide real time movement data. The results of

By Brian McGlynn

There are many factors that can result in a site characterization being limited. For example, a client may undervalue the importance of a good geotechnical report, or an owner may feel that it would take too much time to perform an appropriate investigation among other reasons. For this project, neither was the case. The challenge was that the construction sequence of work required wick drains to accelerate the settlement of soil that had yet to be placed, resulting in the need to create a wick drain bid package based on unknown settlement parameters. This wick drain project took place in Long Beach, California, at the Long Beach Middle Harbor Re- development. For much of the past decade, the Port of Long Beach undertook a $1.5 billion redevelopment of two outdated terminals to create the Long Beach Container Terminal (LBCT). To achieve this goal, the existing terminals were demolished and the slip that serviced one of the older terminals was designed to be infilled to create the new area that would allow for the LBCT to manage 3.3 million TEUS (a commonly used freight term meaning twenty-foot equivalent unit) of cargo each year. Ultimately, the construction of the LBCT would be performed under multiple contracts to allow the new terminal to begin operation in a phased approach. Menard performed the wick drain installation under two out of three contracts, and this case history focuses on the challenges anticipated and faced under the second of these awarded contracts.

May 1, 2023

By Paul Summers, Kevin Richardson, Willem (Billy) Villet, Paul J. Sabatini, Attasit Korchaiyapruk, Edward C. Clukey

"A deep mixing method (DMM) foundation was selected by the Project Team for a very large LNG facility in West Africa. As described in a companion paper, this foundation consists of a large number of columns installed by mixing cement with in-situ soils. The foundations are arrayed as a variety of honeycombed type configurations which, if installed to desired specifications, can provide a robust foundation alternative. The foundation is capable of distributing loads and limiting settlements even if some of the soil in the columns is not fully mixed during installation. An important part of the overall quality assessment program, therefore, involved developing a testing program to verify the methodology. In addition the impact of potential defects in columns on the overall foundation integrity had to be assessed. This paper describes some of the preliminary work done to establish the requirements for the quality assurance program. A key component of this program involved the sampling frequency used to assess potential defects in the columns. To verify the column integrity 104- mm samples were taken continuously at a selected frequency through the 23 m long columns. The preliminary work described in this paper demonstrated that the appropriate sampling frequency depends on both the desired reliability level as well as the number of defective columns encountered during testing.Initial finite element analyses were performed to assess the extent that defects could occur in columns within the honeycombed structure without adversely affecting the overall foundation integrity. The results from this work demonstrated that the spatial location of the defects was critical to properly assessing the foundation integrity.In addition to column sampling a load test was performed as part of the foundation verification process. The methods used to apply appropriate loads so that loads at the bottom of the columns approached design values are discussed in the paper.The results obtained from this preliminary study were then used to help develop a more comprehensive assessment program, described in a companion paper, to determine the robustness of the DMM foundations for both the LNG processing facilities and a condensate tank.IntroductionFoundations constructed with the Deep Mixing Method (DMM) can be an attractive and cost efficient alternate to other deep foundation options. This foundation is constructed by mixing soil and cement with an auger type drill. The foundation is usually constructed with a dual auger system that simultaneously creates two contiguous columns called foundation elements. Many elements are then arranged in a honeycombed configuration to create the overall foundation (Figure 1). A desired column strength can be obtained by varying the volume of cement added to the columns, the mixing rate of the soil and stroking sequence."

Jan 1, 2017

By Robert B. Bittner

The new gated dam on the Monongahela River at Braddock, Pennsylvania, was built for the US Army Corps of Engineers using an innovative ?In-the-Wet? technology. A key feature of this technology involves construction of the foundations through the water and later mating the completed structure or a shell of the structure to the pre-installed foundation. This paper presents a description of the structure, its foundation, construction sequence and design details required to successfully implement this technology.

Jan 1, 2013

By Ed Revoort, Robert Schippers

In Rotterdam in the Netherlands the project ‘De Zalmhaven’ is being developed. The project consists of the realization of houses, parking facilities, two residential towers of 70 m and a residential high rise of 215 m. An artist impression for the project is given in figure 1. For the high rise a new development in the use of large diameter, drilled piles with a steel casing has been successfully utilized. In this article the installation method of 65 m long steel drilled piles in two consecutive sections is presented. The settlements for the building (and the influence on its surroundings) have been analyzed in detail using 3D Finite Element calculations, which will also be discussed. Finally there is focus on the results of settlement measurements carried out during construction in relation to the settlement prognosis.

May 1, 2022

By Robert B. Bittner

The new gated dam on the Monongahela River at Braddock, Pennsylvania, was built for the US Army Corps of Engineers using an innovative "In-the-Wef' technology. A key feature of this technology involves construction of the foundations through the water and later mating the completed structure or a shell of the structure to the pre-installed foundation. This paper presents a description of the structure, its foundation, construction sequence and design details required to successfully Implement this technology.

May 11, 2007

By Abhijit R. Sheth, Craig M. Benedict, John Brun, Ara G. Mouradian

"Amtrak recently replaced the 1907-era bascule two-track bridge over the Niantic River between East Lyme and Waterford, Connecticut. The project included new approach embankments, with approximately 2,500 lineal feet of retaining wall along the west approach and 780 lineal feet of retaining wall along the east approach. The paper focuses on the design and construction of the east approach retaining wall, whose alignment is directly adjacent to an existing wetland area which required protection. An anchored prestressed concrete sheet pile retaining wall was selected for the east approach. A combination of concrete anchor piles and ground anchors were used to support the wall. The design of the wall took into account two simultaneous train live loads, support of electric traction catenary structure foundations, and construction live load, while at the same time preventing permanent impacts to the adjacent wetlands. The design considered challenging subsurface conditions, shallow groundwater, the close proximity of the existing operating tracks, construction staging, and storm surge events in Long Island Sound.INTRODUCTION AND PROJECT HISTORYThe National Railroad Passenger Corporation (Amtrak) recently replaced the 1907-era bascule two-track bridge (No. 116.74) over the Niantic River, between East Lyme and Waterford, Connecticut, along the heavily-traveled Northeast Corridor (NEC). The two NEC tracks, which carry over 50 trains per day, run east-west over a narrow spit of land known as “The Bar”, which separates the Niantic River’s marine estuary to the north from the Niantic Bay to the south, before crossing the river. The bay is an arm of Long Island Sound and is occasionally subject to storm surge from hurricanes.The 1907 bridge was built as a replacement for the previous 1891-era swing-span bridge, and was constructed parallel to, and 49 feet north of, the swing-span structure. The two-track 1907 bridge consisted of a single-leaf bascule span and four approach spans supported on stone masonry piers and abutments. The new bridge increases horizontal navigational clearance for marine traffic in the river from 45 feet to 100 feet, and vertical clearance from 11.5 feet to 16 feet above mean high water with the bridge in closed position. The new bridge, constructed 58 feet south of the 1907 structure, features a single-leaf bascule span of 141.5 feet, with an approach span on either side."

Jan 1, 2017

By Ray Zelinski

Caltrans sponsored a research project in 1992 which incorporated proprietary and generic pile types. The piles were subjected to axial tensile/compressive loads in deep, soft soils. Descriptions of various pile types and systems, scenarios leading to the proposal to test the systems, and load test results were/will be provided by other presenters at this seminar. Therefore, this paper will focus on the issues surrounding use of test results and proprietary pile systems on Caltrans construction projects. The primary issues facing Caltrans during implementation are as follows: 1) producing pile cap designs for a range of pile types and loads; 2) providing construction specifications which allow fair competition among the system vendors, yet assure design and ultimate capacities; 3) Develop quality control standards for pile system materials and installation techniques which guarantee pile durability for static and dynamic loads; and 4) assure that foundations have adequate lateral capacity.

Jan 1, 1993

By David White

"When finished (projected completion in 2016) the Hong Kong-Zhuhai-Macau Bridge Project will comprise three cable-stayed span bridges and a 4.15 mile immersed tube tunnel - linking Hong Kong to Macau and the mainland Chinese city of Zhuhai. The design included two artificial Islands to serve as the transition structures for the tunnel to bridges, entailing a massive seaborne land reclamation project, and the use of thousands of sheet piles, and man-hours. The challenges of driving individual steel sheet in 100’ of water are well known, let alone in the open waters of the South China Sea.In 2010 a joint effort between American Piledriving Equipment (APE) and Allnamics Pile Testing Experts convinced the Chinese contractor First Harbor Marine Group China that a massive multi-vibro hammer can be used to drive 130’ long, 72’ diameter steel pipe piles weighing 662 US tons each into the sea bed of the South China Sea for the Hong Kong - Zhuhai - Macau bridge artificial islands. Combining APE’s hammer design, production and operation know-how with the pile driving simulation and installation know-how of Allnamics made it possible to show the feasibility of driving these gigantic piles into bottom of the sea to the required depth.INTRODUCTIONThe challenges of driving individual steel sheets in deep water are well known, let alone in the open waters of the South China Sea. Often the challenges of construction are overcome with engineering or equipment. The challenges of China’s Hong Kong-Zhuhai-Macau Bridge, on the drawing board since 1983, were to overcome both. The challenges of overcoming the skepticism of the Chinese Engineering community would be another story.The finished project will comprise three cablestayed span bridges and a 4.15 mile immersed tube tunnel linking Hong Kong on an eastern span to the China mainland cities of Zhuhai and Macau via two western spans."

Jan 1, 2017

By K. Ronald Chapman, Claus Ludwig, Doug Jenevein

"In the spring of 2005 Schnabel Foundation Company completed a $15.2 million Design/Build subcontract to underpin 11 structures, and provide 202,800 square feet of earth retention for the Reno Transportation Rail Access Corridor (ReTRAC) project in Reno, Nevada. Schnabel’s work was part of a Design/Build contract to depress a railroad alignment through downtown Reno. The depressed section was 2.2 miles long, 54 ft wide, and up to 35 ft deep (3.5 km long, 16.5m wide and up to 10.7m deep). The trench structure was required to be watertight. SUBCONTRACT WORK OVERVIEWEleven buildings along the track alignment required underpinning. Three types of underpinning were used, designated Type 1, Type 2 and Type 3.At four buildings the trench retaining walls were to be located directly under the exterior footings. This alignment eliminated traditional underpinning and cut-off wall techniques that could normally be used to support structures. Type 1 underpinning was used at these buildings. This underpinning system consisted of a combination of permeation grouting, hand-dug piers, and permanent tiebacks. This underpinning system became the new watertight trench walls.Five buildings were located a few feet behind the trench walls, and their exterior walls were supported by continuous footings. Type 2 micropile/pile cap underpinning (patent pending) was used to support these buildings.The remaining two buildings were also located a few feet behind the trench walls, but they had column footings along the exterior walls. At these structures traditional micropile underpinning was provided through the existing footings. This is described as Type 3 underpinning.Temporary earth retention was required on both sides of the trench along most of the alignment. This shoring supported frontage roads, private property and surcharge from the temporary railroad shoofly running parallel to one side of the trench.SUBSURFACE CONDITIONSThe soil along the trench alignment consisted of river outwash deposits. The top 2 to 18 feet (0.6m to 5.5m) generally consisted of flood plain silt and sand deposits, or fine-grained fills. These fine-grained soils are underlain by the Tahoe Outwash Formation which consists of interbedded layers of sand; sand and gravel; and sand, gravel, cobbles and boulders. Some of these layers encountered during construction consisted of 30 to 50 percent cobbles and boulders, with some boulders up to eight feet in diameter.A major challenge to the design and construction of the trench structures and the underpinning was the ground water table which was 10 feet (3m) above subgrade in the deepest portions of the trench. Based on specification restrictions, temporary and permanent dewatering was not feasible. As a result, the selected design and construction methods had to consider three water conditions: the anticipated groundwater level during construction (CGW), the groundwater level for permanent design (DGW), and an additional special design condition with water at street grade."

Jan 1, 2006

By Charles M. Wilk

"Mass stabilization involves mixing binding agents into marginal or contaminated soil to improve the subject material’s physical and/or chemical properties. This paper concentrates on the principles of soil mixing and benefits and application to new and existing rail right-of-way. Successfully applied in Scandinavia and other European countries, the soil mixing is now being applied in right of way in the northern latitudes of the U.S. and Canada. These regions have significant areas of “peaty” soils that can complicate construction and maintenance of rail and structure foundations. Mass stabilization can be used to improve the bearing strength of these soft soils for subsequent construction of railroads, pipelines, roads, and buildings. In civil engineering, the technology is often used to improve the construction properties such as bearing strength, of a marginal soil. In environmental engineering, stabilization is remediation treatment technology that protects human health and the environment by immobilizing hazardous constituents within the treated material. . The treatment is conducted while the subject material remains in-place (insitu). Mass Stabilization is often used to accomplish both civil and environmental purposes on the same project effectively addressing marginal soil while eliminating the expense of soil removal and replacement.This paper presents the principles of mass stabilization technology, implementation in the field and recent completed railway projects.The example rail projects will present the various benefits that soil mixing provides to railway construction and maintenance. Bench-scale studies and full scale implementation as well as soil construction properties before and after mass stabilization will be discussed. The paper and presentation will include information on the advantages of mixing methods and binding agent delivery systems.INTRODUCTIONNew or existing railroad right-of-ways may cross ground with low bearing capacity. Right of way subgrade undergo deflection (strain) as loads (stress) are applied (1). The amount of strain or deflection of the subgrade caused by loading of a train is proportional to the stiffness of the subgrade materials. Some soils, such as tamped ballast, are very stiff and resist loads well. Other soils such as soft clay, peat, or loose sand have low stiffness and undergo substantial movement under loads. It is very desirable to have the stiffest possible material in a track subgrade. Stiff subgrade material limits deflection under load, reducing track roughness and occurrence of track defects. Mass stabilization is a geotechnical method that can be used to improve the bearing capacity or stiffness of soil in these right-of-way. Mass stabilization involves mixing binding agents into soil subject to treatment while the soil remains in-place or insitu. Variations in the design or areas subject to treatment can be used to address transmission of vibration to adjacent structures."

Jan 1, 2017

By Jeongbok Seo

This paper describes successful application of driven tapered-steel-pipe piles for two large-scale projects in the New York metropolitan area: Rego Park Mall, Rego Park, N.Y. and 164 Kent Avenue, Brooklyn, N.Y. The combination of side friction and end bearing resistance produced by tapered-steel-pipe piles has been well-recognized as greater than the side friction and end bearing resistance by pipe piles. Forty-four tapered piles were driven and tested at these two sites. Design pile load for the two sites was 260 kips for Rego Park Mall and 400 kips and 300 kips for 164 Kent Avenue. To measure the pile-drive hammer efficiency, the compressive stress in the pile, and to estimate the ultimate bearing capacity of the pile, dynamic load testing using a Pile Driving Analyzer (PDA) was conducted on index piles at the sites. Subsequent to the field testing, data analysis using the Case Pile Wave Analysis Program (CAPWAP) was conducted. Restrike PDA analysis and full-scale static load tests were performed on the selected test piles. Test piles at the project sites exhibited significant time-dependent increases in bearing capacity caused by the effects of "set-up" or "soil freeze." The dissipation of excess pore-water pressure in the soil, which had been disturbed and remolded by driven pile, was generally considered the primary cause of set-up. The increase at the subject sites ranged from 100 to 300 percent of the capacity measured at the initial driving. This paper discusses the results of various types of load testing on tapered piles and the set-up effects by comparing PDA test results acquired during and after pile driving. Finally, an empirical relationship for the New York metropolitan area has been offered for quantifying set-up.

Jan 1, 2008

By Peter A. Thompson, Richard E. Prust

"The Bangkok Mass Rapid Transit (MRT} Chaleom Ratchamongkhon Line project is the first underground subway to be completed in Thailand. It consists of 22 km (14 miles) of twin-bored tunnels and 18 cut and cover stations constructed within the deltaic deposits that underlie the city. This paper describes the ground conditions, site investigation, including the use of the self-boring pressuremeter and the associated design issues for the construction of deep foundations. The paper also describes a selection of the various deep foundation solutions that were adopted to address particular constraints of the project and the ground conditions, including slurry walls for the cut and cover stations and foundations used for the underpinning of existing structures.INTRODUCTIONThe MRT Chaloem Ratchamongkhon Line Mass Transit Underground Railway comprises approximately 22 km (14 miles) of tunnels and 18 stations. The route is shown in Figure 1.The project was divided into two design and build contracts. The northern section was awarded to the ION joint venture, composed of Italian-Thai Development PLC, Obayashi Corporation and Nishimatsu Construction Co Ltd. Arup were contracted by ION for the design of the northern section. The section comprises 11 km (7 miles) of twin-bored tunnels, nine cut and cover station tunnels constructed within perimeter slurry walls using top down construction methods, and two cut and cover tunnel structures.The majority of the route of the northern contract follows existing highway Rights of Way. This results in the tunnel alignment passing through the foundations of existing highway bridge structures for which a variety of deep foundation solutions were adopted to underpin these structures.An 8-story park and ride building in the Lat Phrao area was also constructed using deep foundations."

Jan 1, 2005

By Glenn J. Rix, Eduardo Tavera, Raphael Siebenmann, Zhongjie Zhang, Robert C. Bachus, Jongwon Jung

"The Louisiana Department of Transportation and Development (LADOTD) uses a variation of the FHWA-modified Gates equation to verify the nominal pile bearing resistance, typically on smaller projects where static load tests and dynamic monitoring are not practical. An inconsistency in the resistance factors for load and resistance factor design (LRFD) penalizes the target pile capacity needed during field observation if the LADOTD dynamic formula equation is used, which is unreasonable, and has created confusion among designers, consultants, district personnel, and inspectors in Louisiana. The objectives of this project are to recalibrate the FHWA-modified Gates equation and update the associated LRFD resistance factor for pile types and local soil conditions encountered in Louisiana. Improved consistency relative to the current design approaches will be achieved if the updated resistance factor matches or exceeds the worst-case resistance factor used by LADOTD, which will reduce confusion among users. Updating the resistance factor will also serve to increase confidence in the FHWA modified Gates equation, optimize the efficiency of the piles, and reduce project costs.IntroductionThe original 1957 Gates pile driving formula (Gates, 1957) is an empirically derived dynamic formula that is used to predict pile capacity in the field during pile installation. The original Gates formula tends to over-predict pile capacity for low driving resistances and under-predict pile capacity for high driving resistances (Hannigan et al., 1998). Thus, the Federal Highway Administration (FHWA) proposed a modified version of the Gates formula that addressed this limitation. The FHWA–modified Gates equation is:"

Jan 1, 2017