Search Documents

By S. Chung

Mining in highly stressed ground conditions has been an increasing challenge at the Brunswick mine. Over the past 30 years, two large regional pillars were established on the 1000 m Level to support the ground for safe extraction of the surrounding ore. The South Regional Pillar contains about 5 Mt of ore and the North Regional Pillar has about 3 Mt of ore. In the fall of 2000, mining activities were suspended following a series of ground movements around the South Regional Pillar along weak geological structures. After extensive geotechnical investigations, a decision was made to carry out a mass de-stress blast in the West Ore Zone (WOZ) to cut the principal stress across an area of 135 m along strike and 86 m high. At the end of July 2001, the WOZ mass blast was successfully initiated. Following this success, the mine decided to take a similar approach to de-stressing the North Regional Pillar (NRP). The final mass blast was taken in early February 2003. Advanced blasting technologies, including state-of-the-art electronic detonators and blast simulation, played an important role in achieving the successful blasts. The high precision of delay timing and long delay duration of the electronic detonators ensured accurate and reliable initiations of over 800 blastholes in the WOZ mass blast. Orica’s DMC_Blast (Distinct Motion Code) simulation code was used to study different blasting blocks for the desired timing in the initiation sequence. This paper describes the process of applying electronic detonators in complex blasts, and discusses how blast simulation results were interpreted to guide engineering design of the mass blasts.

Jan 1, 2005

By L. Nichols, H. Keele, K. Czajewski

"The oil sands industry in northern Alberta disposes of the by-products of bitumen extraction into tailings ponds. The mix of tailings sand and mature fines, with gypsum added as a flocculent, constitute a waste stream called consolidated tailings or composite tails (CT). The two main challenges of the tailings disposal process are a chronic shortage of economical containment and the potential mobility of CT deposits in the event of breaching by, for example, long-term erosion, which makes abandonment of tailings ponds more complicated. Thick deposits of CT do not consolidate in adequate time to provide reassurance for abandonment of the CT containment facilities and that is why the containment must be adequately robust or the properties of CT improved for long-term stability. This paper addresses potential solutions to these problems by applying the gravity drainage of CT and quasi-homogeneous construction for containment facilities.Gravity drainage is suggested as a mechanism to facilitate the consolidation of CT in critical areas of the ponds by inserting internal sand layers within the body of the deposit. Critical CT areas are defined as areas around the perimeter of containment. The advantages of this solution are longterm stability of the disposal area by creation of stiff deposits around its perimeter and facilitation of reclamation efforts on its surface.The present solution for containment of CT deposits is not favourable from a materials balance point of view. In general, sand has become a valuable resource as it both forms the primary component of the CT matrix and becomes the containment building material. If sand is required for CT, less is available for dyke construction. This puts additional pressure on the industry as a whole to maximize the use of overburden and interburden for construction of tailings containment structures. Typically, only 50 percent of dry mine waste (overburden + interburden) is incorporated into dyke construction. The remainder of dry waste is stored either in waste dumps or in tailings ponds, consuming valuable in-pond space originally allocated to CT material. Quasi-homogeneous dykes are proposed to contain CT deposits rather than traditional minimum cross-section dykes built of overburden and/or cell sand. The quasi-homogeneous dyke may change the unfavourable material balance and lessen the construction constraints that are presently imposed on the mine/waste disposal process."

Jan 1, 2008

By L. D. Haig

"The Texada Mill is a unique iron operation producing High Grade sinter iron concentrate and a by-product copper, gold, silver concentrate. The plant is complex and extremely flexible to handle the many varieties of ore. Two iron concentrates are made and blended. A coarse iron concentrate from primary grinding and a fine concentrate after rougher flotation to remove all the sulphides.All the tailings from iron processing are collected, dewatered, reground and floated for additional copper recovery.The entire milling operation has been carried out in all sea water for seven years and mixtures of sea, fresh, and reclaimed water for ten years prior to that.A very stable float results from the use of sea water at the natural pH8. Reagent Consumption is lower and Metallic Corrosion of mill liners and grinding media is actually less than local fresh water or mixtures of fresh and sea water.Marine growth in pipe lines can be periodically removed by violently bubbling high pressure air up through the water filled mains.Location:Texada Mines is located on tide water on the west side of Texada Island 100 miles northwest of Vancouver, B. C.The Island is served by a 30 car ferry, tug and barge and a scheduled air service from Vancouver to a company maintained air strip near the mine.The climate is moderate with about 30 inches of rain during the winter and relatively dry summers."

Jan 1, 1974

By Richard Mcivor, Largo Albert

"Inco Limited has operated aluminum mine shaft conveyances since 1968. Aluminum conveyances are used where the hoisting in system requires lightweight conveyances to maintain the hoist rope safety factors and mine hoist rope pulls as dictated by government regulations. Inco Ltd. currently has 20 skips (including spares) operating in the Ontario Division mines. The main problems encountered are with galvanic corrosion between dissimilar metals and metal fatigue. This paper will highlight some of the problems encountered and illustrate methods utilized to overcome the problems and improve the conveyances performance.IntroductionAluminum mine shaft conveyances have been in use at Inco Limited's various Sudbury district mines since 1968. All of the conveyances currently in use are skips used for hoisting mine ore and rock. Inco had an aluminum quick change Kimberley-type skip and cage in operation at its Totten Mine in the early 1970s, but this mine is no longer in operation and no further comment will be made.The primary reason why aluminum conveyances are chosen over conventional steel conveyances is because of their light weight. Typically an aluminum conveyance will weigh about 60% to 70% of a steel conveyance of similar design. The lighter weight conveyances will allow higher payloads to be used and still maintain the statutory hoist rope factors of safety. It must be remembered that increasing the payload will increase the power required to raise the load and the hoist will have to have the necessary horsepower for the increased payload or the system will be overloaded.The front dump (Rola-chute) skips are of the bail-less design, i.e. the box structure also supports the load and has the shaft guide shoes attached directly to the side of the box structure. The Copper Cliff North Mine and South Mine skips have a joint in the centre of the conveyance and are installed in the shaft in two sections and connected with pins. This feature allows very long (42 ft) skips to be used in areas where a one-piece bail-type conveyance could not be installed. It is not practical to make sectionalized bail-type conveyances"

Jan 1, 1988

By M. Courchesne, C. Barbery, D. Hodouin, C. Carrier

"The carbon-in-pulp process for recovery of gold dissolved in dilute cyanide solutions, in the presence of solids, has now replaced the convedntional processes of pregnant liquid/barren solids separation followed by Merrill-Crowe precipitation. Most plants built over the past ten years incorporate a CIP section. The process is described as cheaper in capital and operating costs, and few major start-up or operational difficulties are reported. For the purpose of the present paper, the CIP process will be assumed to consist of the following sequence of operations (Figure 1):- the slurry stream coming out of the cyanidation circuit is first screened to remove any tramp oversize material. Gold dissolution is assumed to be complete before entering the CIP circuit.- the slurry is sent into a series of agitated tanks in which it is mixed with activated carbon. The carbon particles size is much coarser than the top size of the ground ore. The tanks are fitted with screens that allows the slurry to overflow continuously into the next tank, while retaining the carbon in the tank. Slurry dilution is adjusted to prevent carbon from settling in the tanks. Agitation intensity is kept low in order to minimize carbon abrasion.- carbon is transfered from tank to tank in a discontinuous manner. According to a specific schedule, the carbon from tank one is removed, then carbon from tank two is sent to tank one, and so on, till the last tank, which is filled with regenerated carbon corning from the elutionregeneration section. The amount of carbon removed, the transfer from tank to tank, the sequence of transfer, the carbon inventory in the various tanks are parameters which are, up to a point, at th2 discretion of the operators, as long as they remove, batch wise, an amount of loaded carbon containing a similar quantity of gold to the one that has entered the circuit since the last transfer."

Jan 1, 1987

By B. Tanda

A process has been developed at Curtin University whereby glycine is used in an alkaline environment to leach gold, silver and copper from their ores, concentrates, process intermediates and wastes. Copper mineralisation investigated includes various oxides, sulfides and native copper. The leach process utilises an oxidising environment such as oxygen. Glycine is a non-toxic, non-volatile, edible, low cost reagent which is produced in large industrial quantities for use in several industries. Glycine and its copper and precious metals complexes are stable over wide pH, Eh and temperature ranges. Other than losses in leach residues, the glycine is recovered and recycled for leaching. Iron dissolution is insignificant in the pregnant leach solution. Iron in pyrite remains unaffected, whereas iron associated with base metal sulfides (e.g. chalcopyrite and bornite) is converted to a readily filterable iron hydroxide. Efficient separation of copper by solvent extraction and conventional electrowinning has been shown to be feasible for a number of organic extractants, whereas gold and silver glycinates adsorb very well onto carbon allowing CIP/CIL/CIC (carbon-in-column) based processes. The process is ideal for ores containing acid-consuming gangue, concentrates with high arsenic or halide contents and for copper-gold ores with significant sulfide mineralisation. The process eliminates many of the problems associated with the processing of copper-gold-silver ores, such as elemental sulfur formation, silica gels, unwanted metal co-dissolution, and jarosite precipitation. The reagents used and process residues are much safer and environmentally benign than conventional process options. The processing technology can be applied to in-situ, heap and vat, or agitated tank leaching at temperatures ranging from ambient to below 100?C at atmospheric pressure and is currently being commercialised. This paper will focus on copper leaching and recovery and iron rejection from a chalcopyrite flotation concentrate.

Jan 1, 2016

By J. Shang, P. Howarth, B. Morris

Tailings from the nickel refinery in Copper Cliff, Ontario, consist of fine silicates mixed with a variable amount of conductive and magnetic minerals mainly associated with sulphides and iron oxides. Subsequent oxidation of sulphide- rich phases within the tailings results in the formation of an acidic leachate that may contain significant concentrations of trace metals. Mapping the spatial distribution of regions of higher sulphide concentration therefore provides insight into the distribution of the acidgenerating potential within the tailings. Electrical conductivity is constrained by two parameters — the concentration of metallic sulphides and the ionic concentration of acid in groundwater. Magnetic susceptibility is directly related to the pyrrhotite and magnetite content. It is proposed that combining information derived from airborne electromagnetic and magnetic surveys can provide an indication of metallic sulphide distribution. Preliminary investigations of airborne electromagnetic and magnetic data acquired concurrently over the sulphide-rich Copper Cliff tailings site reveal that these parameters can provide information on mine tailing extent and permit separation of tailings with varying compositional and alteration levels. Airborne geophysical data provide information about the subsurface while a digital elevation model (DEM) and hyperspectral imagery record surface conditions. Integration of the two data sets can reduce ambiguity when interpreting mine tailing distributions and their subsequent alterations.

Jan 1, 2001

By C. J. Brown

Controlling the level of impurities in copper refinery electrolytes is essential to achieving acceptable cathode purity. Purge of electrolyte is not an entirely satisfactory solution since the cost of neutralization, waste disposal, and replacement acid can be appreciable. The APU® process utilizes ion exchange resin to sorb sulphuric acid while rejecting metal salt impurities. Extensively employed for recovery of waste pickling and anodizing acids since 1977, the system is now being used at several refineries for removal of contaminants such as antimony, bismuth, iron, and nickel. The purified acid, which is recovered from the resin by water elution, is recycled back to the refinery tank-house, while the metals are typically recovered from the de-acidified by-product solution by precipitation.

Jan 1, 2005

By W. K. Gowans

The Sullivan Concentrator treats a complex sulphide ore consisting mainly of galena, marmatite and pyrrhotite. The ore carried minor values in silver, antimony, bismuth, indium and tin. The products of the concentrator are lead, zinc, iron and tin concentrates. The minor metal values other than tin are recovered from the concentrates by the refining processes in the smelter at Trail.The concentrator was completed in 1923 and first operated with a capacity of 2,500 tons per day. In the years 1926 to 1929 changes to equipment and buildings brought the operation up to 5,500 tons per day and then, in the years 1935 to 1945, the daily tonnage was raised to 8,500 tons. After 1945, the rising insoluble content of the ore made it necessary to consider the construction of a Sink-Float plant. At this time consideration was also given to the construction of a new crushing plant underground to replace the rolls crushers and cone crushers located at the concentrator. By 1949, construction of the Sink-Float plant was completed along with a new underground crushing plant, and an electric haulage way between the underground crushing chamber and the Sink-Float plant. The ore was hauled in forty 14-ton car trains which discharged into a 3,000 ton receiving bin by means of an air operated five car rotary dumper. With the start up of the,Sink-Float plant, a 1 ½ ft. by 12 ft. Hardinge rod mill was also brought into operation. The Sink-Float plant made it possible to treat 12,000 tons/day of mine run ore with up to 40% of this being rejected as float.

Jan 1, 1975

By R. Kwiatkowski

Agenda ? Health Canada Protocol _ Screening Level Risk Assessments (SLRAs) Contaminants Foods Exposure Pathways COPCs _ Site Specific Risk Assessments (SSRAs) In-depth, quantitative Monitoring Exposure estimates Food Issues in Environmental Impact Assessments ?Country Foods? ? Foods gathered from the project area and consumed by local residents.

Apr 1, 2005

By E. Henry, C. Mayer, H. Rott

Hangingwall deformation monitoring at Kiruna mine is a major concern for Luossavaara- Kiirunavaara AB (LKAB) since underground production is deepening toward the town of Kiruna. In the quest for more effective monitoring techniques, LKAB decided to evaluate the ability of satellite-borne synthetic aperture radar (SAR) interferometry to monitor ground subsidence by generating continuous deformation maps from satellite radar images. While adopted by other geoscience-related industries, SAR interferometry is still relatively untested in the mining industry. This paper describes the basic principles of SAR interferometry and describes how subsidence is monitored at Kiruna mine. The encouraging results are discussed as well as the benefits (continuous deformation mapping, low cost, fast, etc.) and limitations (sensitivity to snow and vegetation cover) of the technique.

Jan 1, 2004

By Donald Strickland, Peter Kresin, Dave Hall

"Have your parents or grandparents ever tried to share with you their wisdom and you ignored it because it did not relate to you‘? I have been ignorant and inevitably grew older and wished I had listened. The result: learning the hard way. As British Astronomer Fred Hoyle once said. “It is the true nature of mankind to learn from mistakes not from example.“ Hopefully we will continue to learn from the examples shared by our fellow mineral processors in these conference proceedings. It is the intent of this paper to share wisdom from the Musselwhite Mine that you may apply to your own operation.This paper is divided into three sections:1. Feasibility3. Operation3 . DesignKey points of the Feasibility and Design stages are summarized. followed by an analysis of actual operating statistics. An attempt is made to relate these statistics back to the feasibility and design with emphasis on areas of success and those with potential for improvement."

Jan 1, 1999

By Ronald E. Hamilton

"An attempt to review the recent literature on comminution reveals at once that the subject has many ramifications and that the applications are so diverse that there are very few general statements which can be made.It. seems reasonable to start classification on the basis of size of material as Input to the comminution process. However, we find that this can only be done in a very imprecise manner.The initial step of breaking rock from its natural state of very large pieces in geological formations into sizes suitable for processing is accomplished by blasting. This step in the process has not been ex-amined in this project except to note that great changes have been made during the last decade or so in the explosives used, and in the method of handling them. We should determine what effect changes in mining methods can have on the need for crushing.The second step in the process is usually primary crushing, performed by gyratory or jaw crushers. The largest chunk which can be fed to a jaw crusher depends on the size of the machine, and should be larger than the largest fragment produced in the miring process. It is obvious that the larger the crusher, the less care required in mining to en¬sure the absence of rocks too large to be crushed. The optimum size of crusher to minimize overall cost of mining and reduction is not at all obvious, and no information on this point has come to light in this investigation.It is rather generally accepted that size reduction is most efficiently done in small stages, and that different machines have different opti¬mum size ranges of feed. For example, crushers are preferred for sizes above about 1"", rod mills for the range between 1"" and 0.1"", ball mills are preferred from 0.1""down to perhaps 10 microns, and vibratory mills, or jet mills, below 10 microns."

Jan 1, 1976

By J. P. Landriault, F. W. Harrison

"Zinc-iron alloy coatings can be produced by either thermally alloying hot-dipped galvanized steel or by electro deposition. Stelco Inc. produces a thermally alloyed Zn-Fe alloy-coated steel, which is mechanically wiped to remove free zinc.A more extensive use of Zn-Fe alloy-coated steel has been predicted for unexposed autobody and structural part applications, since this material is characterized by good spot weldability and formability, and provides superior corrosion resistance under automotive primers.This investigation has examined the coating composition, corrosion resistance, spot weldability and formability of Stelco's Zn-Fe alloy-coated steel and found its properties to be similar to those of Zn-Fe alloy-coated steel produced by post coating annealing.IntroductionRecently, there has been increased automotive interest in galvanneal, which is characterized by good spot weldability, good paintabilityt and good corrosion resistance when primed. Stelco produces a thermally alloyed zinc-iron coated sheet product similar to galvanneal. However, this product is produced by mechanically wiping the free zinc from the surface of hotdip galvanize to expose the underlying zinc-iron alloy.The surface of Stelco zinc-iron alloy-coated sheet is matte gray and has longitudinal streaks which result from contact with Kevlar wipers during production (Fig. I). This paper describes the coating composition, corrosion resistance, weldability, formability and surface appearance of Stelco zinc iron alloy coatings and, wherever possible, compares these properties to those of galvanneal."

Jan 1, 1987

By R. Matusewicz

The key drivers for the copper smelting industry are a complex mix of economic and "human" factors which combine to drive technology in new directions and can provide a strong indication of future industry trends. Recent examples have been the drive to achieve increased scale of production and resultant cost efficiencies by using a single furnace high intensity smelting vessel, and the broad acceptance of Top Submerged Lancing (TSL) technology for this duty. The development and adoption of continuous converting processes to counter the increased pressures faced by the Peirce Smith converting process is another example of the need for innovation. This paper discusses the merits of the continuous converting process, describes how the Ausmelt TSL batch converting process has been adapted to the new Ausmelt Continuous Copper Converting (C3) process in response to these industry trends and examines the Ausmelt continuous converting flowsheet options available to the end user.

Jan 1, 2007

By Paulo F. T. Sachs

ERP systems have been widely implemented nowadays in several industries. However, ERP was originally designed to fit former MRP and MRP II users, and most of the ERP research has been focused on discrete manufacturing . On the other hand, process industries ? and mining in particular ? present many peculiar characteristics, which are difficult to comply with ERP systems standard functionalities. Again, very limited research has been developed covering enterprise management systems in mining. The objective of this paper is to identify, through an explanatory study that includes a case study methodology, how ERP systems manage the functional areas of the mining industry, and how they fit into the mineral value chain IT requirements. A secondary objective is to identify the gaps between ERP?s functional capabilities and the mining industry business requirements, and to point out the perceived benefits they generate to the companies.

May 1, 2004

By H. Lundberg

Introduction The world has been suffering from an excessive production of all kinds of raw materials, and the metals and petroleum are no exception. As a consequence, at the moment, the urge to find new mineral deposits is almost non-existent and prospecting languishes. But from previous experience we know that sooner or later new supplies will be needed. Mineral deposits become exhausted, and to keep up the supplies of our metals and petroleum, new deposits must be found. Even now, a supply of petroleum of domestic production would not be unwelcome in Canada. It is not, therefore, so entirely malapropos to discuss means of finding ores and oil as it would seem. Almost any physical property connected in definite manner with minerals and rocks may be made the basis of geophysical exploration. This is particularly true of electrical resistivity, and its utilization in electrical prospecting has been the deciding factor in the discovery of such big ore-bodies as Buchans mine, Newfoundland, and the large copper ore-bodies in northern Sweden, etc., as well as in the solution of many foundation and structural problems. The importance of electrical prospecting has been growing steadily, and already there exists hardly any exploration project involving geological problems which may not profit by its application. Electrical prospecting is marching on, and neither temporary failures, nor incompetence, nor over-optimism, nor ill-will and pessimism, nor bad times and business depression, will be able to halt its progress.

Jan 1, 1931

By Claude Deveau

"Studies on the performance of Falcon batch type concentrators treating ultrafine tantalum at Tanco have revealed that very fine heavy minerals are concentrated within certain areas of the concentrate bed. This information led to the design of a bowl which would allow entrapped lighter low grade particles to escape while providing more space for heavier particles to be recovered in the bed.Numerous tests were then completed with a modified batch-type and non-fluidized Falcon bowl in which the diameter of the discharge lip was adjusted downward manually in steps. This allowed for the gradual building of a higher grade concentrate bed.This work ultimately led to the design of a new Falcon with an automated continuously variable lip. In April 2005, Tanco commissioned the first Falcon UF600.This paper will discuss laboratory scale results and also plant performance of the Falcon’s UF technology.INTRODUCTIONTantalum Mining Corporation of Canada, also known as Tanco, is a wholly owned subsidiary of Cabot Corporation based in Boston, Mass. Operating since 1969, the underground highly mechanized room and pillar operation produces tantalum, lithium and cesium minerals and is located a 2 hour drive east-northeast of Winnipeg Manitoba, Canada.At Tanco, tantalum is recovered using conventional gravity concentration, enhanced gravity concentration and flotation. This paper will discuss how the need for improved equipment to treat very fine tantalum particles was filled by a machine which was modified to the point of creating a completely new technology.In November 2003, Tanco began the investigation for the potential use of a high g-force smooth walled concentrator for treating ultra fine tantalum produced by its flotation circuit. Until then, the tantalum flotation concentrate had been treated by a circuit which consisted of a Mozley Multi-Gravity Separator 902 (MGS), a Mozley MGS 900 and a Bartles cross belt concentrator. Through QemScan analysis, it was found that the majority of the losses from this circuit were of an extremely fine nature which exceeded the recovery limits of equipment on hand. Mean particle size of the tantalum losses was less than 10 µm."

Jan 1, 2006

By Marc C. Bétournay

A mine production locomotive, the world?s first applied industrial fuelcell vehicle, has been designed and tested in the context of a number of proof-of-concept projects supported by the Fuelcell Propulsion Institute, an international consortium of stakeholders dedicated to facilitate the commercialization of fuelcell vehicles. The locomotive?s simple electric-powered motor and controller system was ideal to study a number of requirements related to fuelcell power application: hydrogen power plant operation, underground hydrogen use, risk and regulatory requirements, production performance versus the conventional battery-powered locomotive version under measured duty cycles and production requirements, power plant design improvements for other fuelcell vehicles, and cost-benefit aspects. This article will focus on the design and testing aspects of this project which has led to successful performance demonstrations of the vehicle under surface and underground conditions at two mines. It will also present information on the creation of a safe, reliable and efficient power plant which fulfilled its design objectives, including longer productivity time for a given vehicle fill-up.

May 1, 2003

By K. C. Armstrong, A. B. Cron, L. A. Melis

"The Johnny Mountain gold mine in northern British Columbia, owned by skyline Gold Corporation, has been in operation since August 1988. Mill operating difficulties at the start of the operation resulted in a depleted cash flow situation and quick improvements were required to generate a self-sustaining financial basis of operation. In October 1988, Melis Engineering Ltd. was contracted to identify metallurgical difficulties, implement necessary modifications, and undertake mill operations and personnel training in order to achieve production targets.This paper presents the operating difficulties which existed at start-up and describes the methodology used to overcome production problems. Metallurgical testing results are described along with the modifications made to the milling circuit to suit ore metallurgy. Plant changes led to the operation of a simple gravity/flotation circuit to recover gold as bullion and in a copper concentrate. Operation of the originally installed cyanidation circuit was discontinued. This contributed to substantial savings in operating costs and virtually eliminated environmental problems. PROPERRTY LOCATION ANR DESCRIPTIONThe Johnny Mountain mine site is located in northern British Columbia along the Iskuit River about 60 km east of Wrangell, Alaska and 275 km north of Terrace, B. C.. A location map is presented in Figure 1 and a site plan is shown in Figure 2. The complex is located on a mountain plateau about 3, 600 feet above sea level. The plateau is flanked to the north by Johnny Mountain and surrounded on the other sides by steep cliffs."

Jan 1, 1990