Search Documents

By S. H. Castro

Molybdenite depression by shear degraded polyacrylamide solutions has been investigated. Aqueous solutions of polyacrylamide-type flocculants were subjected to shear degradation under a range of high-speed stirring conditions. Settling tests, carried out with quartz slurries and sheared polyacrylamides, showed reduced flocculant performance with increased degradation. As the sedimentation rate is strongly dependent on the polymer's molecular weight, these results fit well with the shear degradation theory, which predicts the production of shorter chain segments due to breakage of the polymer macromolecules. Microflotation tests on natural molybdenite showed that the depressing ability of a commercial polyacrylamide flocculant remained unaltered after shear degradation, even when the flocculating ability was entirely lost. Practical implications of shear degradation on molybdenite flotation are discussed.

Jan 1, 2004

By J. D. Zhu

A numerical model for predicting microporosity formation in aluminum castings has been developed, which describes the redistribution of hydrogen between solid and liquid phases, the transport of hydrogen in liquid by diffusion and Darcy flow in the mushy zone, One of the key features of the model is that it uses a two-stage approach for porosity prediction, In the first stage, the volume fraction of porosity is calculated based on the reduced pressure, whereas, in the second stage, at fractions solid greater than the liquid encapsulation point, the fraction porosity is calculated based on the volume of liquid trapped within the continuous solid network, which is estimated using a correlation based on the Niyama parameter, The porosity model uses thermal data calculated using the commercial finite element package ABAQUSTM. The model has been applied to examine the evolution of porosity in a series of experimental samples cast using unmodified A356 in which the initial hydrogen content was varied from 0,048 to 0.137 [cc/100g], A comparison between the model predictions and the experimental measurements indicates good agreement in terms of the variation in porosity with distance from the chill and the variation resulting from initial hydrogen content.

Jan 1, 2005

By Horace Freeman

Introduction In the aggregate, directly and ?indirectly, the pulp and paper industry ? consumes very large quantities of a variety of minerals, or compounds prepared from minerals. This is especially true in the manufacture of news-print, but fine papers, also, account for some of this consumption, in the processes of loading, coating, and otherwise improving the finish. The more important of the minerals used in the industry in Canada are briefly dealt with in the following pages. The list is by no means exhaustive, however. Thus, barite, lithopone, zinc oxide, zinc sulphide, and titanium oxide are used in small quantities in Canada in filling and coating paper. Up to the present time, however, the quantities of these materials used in the paper industry have not sufficed to encourage their manufacture in Canada. In the case of barite (barium sulphate)-or of witherite (barium carbonate)-it may be said that, should deposits of commercial size be discovered in Canada, the ore would have considerable export value, for use in the paper and other industries. China-Clay (Kaolin) Considerable quantities of china-clay are used for brightening and improving the finish of paper, and there is a growing tendency to use larger amounts of this material in newsprint manufacture. No china-clay suitable for paper manufacture is at present produced in Canada, but samples have been forthcoming recently from a deposit near St. Remi d'Amherst, Labelle county, Que., about thirty miles north of the Ottawa river and approximately midway between Montreal and Ottawa, and plans are under way to conduct large-scale tests with this material. Present sources of supply are the United States, England, and Russia.

Jan 1, 1934

By P. L. Wright

"This is a brief history of the development of the mining project, with a description of the proven geology. The paper describes how the experiences gained progressively demanded change in the mine design. The equipment used is described, together with methods of working. Interesting facts have been proved regarding gas emissions and roof. supi;iort. The. working cycles evolved are completely flexible m operation and lend themselves to maximum utilization of the most productive units. The two underground mines are compared, showing the variance in conditions already experienced. Programs currently in operation to improve standards and production are: the training of miners, maintenance men and officials; experiments in floor consolidation and continuing roof support trials; and the effect of comparative stability of working crews on the performance of the operation."

Jan 1, 1973

By M. Tanaka, H. Narita, T. Fuchikami, K. Morisaku, K. Nagao, T. Yoshida, K. Kuroda

The effect of various N-substituents on the performance of amide-containing tertiary amine compounds in the extraction of Rh(III) from HCl solutions was investigated to optimize the structure of these compounds for industrial use. It was found that N-2-ethylhexyl-bis(N-di-2-ethylhexyl-ethylamide)amine and tris(N-di-2-ethylhexyl-ethylamide)amine, which have long, branched alkyl chains, were suitable for Rh extraction, because they were soluble in a practical diluent (80 vol% n-dodecane?20 vol% 2-ethylhexanol) and stable against highly concentrated HCl/Rh solutions, and showed high selectivity for Rh(III) over Pd(II) and Pt(IV).

Jan 1, 2014

By Francois Charette

Corrosion is a significant factor affecting the capacity and working life of ground support. The paper explores a relatively simple method to predict the load capacity of a support system using a Monte Carlo stochastic approach. The analysis uses published field data on existing ground support to evaluate the applicability of the method and its predictive performance. Discussion on corrosion rates found in the field and predicted from laboratory measurement is provided.

Jun 1, 2012

By A. F. Laurin, A. L. Dorr

"Because of its wide areal extent, its numerous lithological facies and its high degree of metamorphism, the Quebec portion of the Grenville province has only partly been explored and prospected. Rock types that are economically among the most interesting in the Grenville are those of mafic and ultramafic compositions, because of their great potential for coppernickel and chromium-platinum. The peculiar mode of occurrence and the distribution of these igneous masses in which copper-nickel mineralization is known to occur indicate' two common geological features: (1) aerial photographs and/or topographic maps strongly' suggest close spatial (and possibly temporal and genetic) association of most of these mineralized mafic and ultramafic intrusions with circular structures; (2) when plotted on a large-scale map comprising the Quebec portion of the Grenville, these circular structures fall along two lines which could correspond to major tectonic features. Even though the genetic links among the mineralized mafic-ultramafic masses, the circular structures and the linear features are not yet fully understood, their associations are believed to be empirically valid and should therefore be used as geological tools by those interested in exploring the Grenville for copper-nickel and possibly chromium-platinum deposits. It should be noted that these mafic and ultramafic bodies do not appear to be spatially related to anorthosite complexes."

Jan 1, 1971

By B. D. H. Knights, M. A. W. Bryson

Flotation of PGM ores, specifically UG-2, presents a number of technical challenges. These centre on the prevalence of chromite. Subject to over-grinding, chromite is primarily recovered to the flotation product through entrainment. This is of unique concern as it must be kept below a threshold for downstream smelting, with significant operational and monetary penalties being imposed should it exceed this concentration. A number of strategies have been developed to maximise PGM recovery in the presence of this unwanted contaminant. Specialised flowsheets form a vital basis and advanced control algorithms further enhance PGM recovery while minimising the recovery of chromite. Advances in Mineral Processing Science and Technology Proceedings of the 48th Annual Conference of Metallurgists of CIM Sudbury, Ontario, Canada Edited by

Jan 1, 2009

By B. W. Snyder

INTRODUCTORY THE earliest known case of transmission of natural gas by pipe lines was early in the Christian era when the Chinese used bamboo pipes to transport natural gas from surface seepages to heat brine for the recovery of salt. Since that time many materials have been used as conduits-hollow wooden legs, wood stave pipe, day tile, cast iron, and, finally -since about 130 years ago - steel pipe. Even then, this new material came into use rather . slowly for, as recently as 80 years ago, wood pipe was still being used. However, as techniques were developed to take advantage of the properties of steel, this material gradually replaced all ethers for the transportation of gas for longer and longer distances at ever increasing pressures. In 1912, one of the longest pipe lines of its size at that time was built-this was a 16-inch line bringing gas from Bow Island to Calgary, a distance of 170 miles. We have been able to find records of only two ether such lines at that time-one a 185-mile 16-inch line from Vivian, Louisiana, to Little Rock, Arkansas, completed in the summer of 1911, the ether a 280-mile line from West Virginia to Toledo, Ohio. This last ? mentioned line was reported in a magazine article of September, 1912, but no indication was given of its size on completion date. It is apparent, therefore, that modern high pressure transmission of natural gas is a technique less than forty years old.

Jan 1, 1951

By N. Bahrani

Knowledge of the state of stress in the Earth?s crust is very important to the safe and efficient development of underground excavations in mining and civil engineering projects. A number of methods have been developed over the past 40 years to assess the stress field in the rock mass. These range from local estimates derived from compilation of regional stress databases to back-analysis of field observations to dedicated in situ measurements. The Geomechanics Research Centre (GRC) at MIRARCO has a long history of undertaking in situ stress characterization and measurement. In this paper, the stress measurement techniques used by the GRC, including overcoring and undercoring in addition to borehole breakout back-analysis, are briefly reviewed. The limitations and application of each technique for different ground conditions and the challenges involved during the field work and in interpretation of the results are discussed. A successful stress measurement campaign is not limited to acquiring valid local measurement, but must include a careful interpretation and integration of the measurement with other geological and geotechnical context information. Based on our experience, it is suggested that all available stress indicators and data are combined and integrated with the local geological and geomechanical conditions to derive a consistent stress characterization for a given site.

Aug 1, 2013

By W. P. Nash, T. E. Mccandless

"Abstract - Detrital minerals of upper mantle origin occur in Holocene conglomerates, pediments and antmounds, and in Oligocene conglomerates in the Green River Basin of southwestern Wyoming. The minerals are derived from disaggregated eclogite and peridotite, and are similar to minerals found in mantle- derived igneous rocks such as kimberlite and lamproite, the primary host rocks for diamond. The Green River Basin bisects the lamproite fields of the Leucite Hills (Wyoming) and Kamas (Utah) and overlies the Archean Wyoming craton, which makes the region favorable for diamond occurrence. Lamproite is the favored host for the indicator minerals because unusual high-Fe salitic diopside macrocrysts from the antmounds and from the ~1 Ma old Leucite Hills lamproites to the northeast are compositionally identical. The salitic diopside is uncommon in other igneous rocks and could be a new indicator mineral for use in lamproite exploration. The Green River Basin indicator minerals are eroded from the ~29 Ma old Bishop Conglomerate, whose source area is the Uinta Mountains to the south. No continuous mineral train exists between the Uinta occurrences and those in the Green River Basin. Assessment of the minerals using established and new geochemical criteria indicate that they formed in an oxidizing upper mantle and were transported to the surface by either kimberlite or lamproite. The existence of cogenetic diamond is unlikely based on the mineral chemistry, but selective removal of diamond indicator minerals through weathering and fluvial transport cannot be excluded. Diamonds and mantle garnets are present in the northeastern Uinta Mountains, but they originated as part of the Diamond Hoax of 1872. A representative mineral assemblage from the true igneous host of the indicator minerals is required to fully establish their economic potential. Post-Oligocene erosion and Pleistocene glaciation have hindered efforts to locate a bona fide igneous source for the indicator minerals. Résumé - Des minéraux détritiques provenant du manteau supérieur ont été trouvés dans des conglomérats, des pédiments et des monticules de fourmis de l’Holocéne, et dans des conglomérats de l’Oligocène du Green River Basin, au sud-ouest du Wyoming. Ces minéraux sont issus du démantellement d’éclogites et de péridotites, et sont semblables aux minéraux trouvés dans des roches ignées provenant du manteau, comme les kimberlites et les lamproïtes. Ces dernières sont les roches hôtes du diamant. Le Green River Basin recoupe les champs à lamproïte de Leucite Hills, au Wyoming et de Kamas en Utah, et il surmonte le craton archéen du Wyoming, connu pour la présence de ses diamants. La lamproïte est l’encaissant privilégié pour les minéraux «indicateurs» parce que des macrocristaux exceptionnels de diopsides salitiques riches en Fer, provenant des monticules de fourmis et des lamproïtes de Leucite Hill (~1 Ma), au nord-est, ont des compositions identiques. Le diopside salitique est rare dans les autres roches ignées et peut être un nouvel indicateur dans la recherche de lamproïte. Les minéraux «indicateurs» du Green River Basin proviennent de l’érosion du Conglomérat de Bishop, daté de ~29 Ma, dont la zone source est représentée par les Uinta Mountains, au sud. Aucune continuité des gisements minéraux n’existe entre les affleurements de Uinta et ceux du Green River Basin. La détermination des minéraux, utilisant des critères géochimiques anciens et récents, indique qu’ils se sont formés dans un manteau supérieur oxydant et qu’ils ont été remontés à la surface soit dans des kimberlites, soit dans des lamproïtes. La genèse du diamant n’est que peu liée à la chimie minérale, mais le lessivage d’indicateurs minéraux du diamant par altération météorique et par transport fluviatile ne peut être exclu. Des diamants et des grenats mantelliques sont présents dans le nord-est des Uinta Mountains, mais sont associés avec le Diamant Hoax de 1872. Un assemblage minéral représentati"

Jan 1, 1996

By J. Drelich

We report structural forces measured for 10 nm silica particles deposited on alumina substrate and 5-80 nm alumina particles on mica using atomic force microscopy technique. For nanoparticles forming clusters, oscillation of structural forces was recorded with a periodicity that is close to the size of the nanoparticles used. Additionally, selected force-separation results indicate that the forces involved between the AFM probe and individual nanoparticles can be studied using the nanoparticle-coated substrates.

Jan 1, 2006

By Nancy E. Wilk

In 2015, more than 1.2 million deaths annually were estimated to be caused by occupational risks (WHO, 2018). In 2021, this estimate increased with the publishing of the World Health Organization (WHO) and the International Labour Office (ILO) Joint Estimates of the Work-related Burden of Disease and Injury based on data from 2000 to 2016 (WHO/ILO, 2021). These global estimates reported that each year 1.9 million people die from exposure to occupational risk factors, 81% of these fatalities resulting from non-communicable, occupational diseases. WHO/ILO notes that the health-related risk factors with the largest number of attributable deaths were exposures to long working hours followed by workplace exposures to particulate matter, gases, and fumes. The health outcome with the greatest work-related burden of deaths was chronic obstructive pulmonary disease, followed by stroke and ischaemic heart disease. In considering the 2021 data published by WHO/ILO, it is likely that the estimates are low and underestimate the true burden of occupational disease and injury. In support of that position, more recently the ILO estimated that “2.3 million women and men around the world succumb to work-related accidents or diseases every year; this corresponds to over 6000 deaths every single day” (ILO, 2022).

Jan 1, 2023

By Burrows. A.

Temperature profiles in the lead smelter sinter bed at Xstrata Zinc Mount Isa sinter plant have been measured using a wireless temperature probe. Corresponding sinter samples have been collected for characterization. The sinter peak bed temperatures were found to be in the range of 1000 - 1200 °C. Microstructures and softening temperatures of these sinters have been characterised. Strong correlations have been observed between peak bed temperature and peak hood temperature, and between mean sinter softening temperature and peak bed temperature. It was found that higher peak bed temperature results in higher sinter softening temperature. For the feed material used in the trials, to obtain sinters with mean softening temperatures above 1050 °C, peak bed temperatures above 1130 °C are required. There appears to be a direct correlation between granule size distribution in the feed and peak bed temperature attained. High peak bed temperatures are observed in sinters with narrow granule size distribution.

Jan 1, 2008

By Y. Wang

Phosphates and fluorides are used as regulators for the removal of silicates from diasporic-bauxite both in direct and reverse flotation. While using dodecylamine chloride as a collector, micro-flotation studies showed that sodium hexametaphosphate has stronger depressing power on diaspore than on silicate minerals with increasing sodium hexametaphosphate concentration at pH 6.5, but sodium fluorosilicate shows poor depression on diaspore with increasing sodium fluorosilicate concentration at the same pH. Zeta potentials of diaspore and silicate minerals become more negative both in the presence of sodium hexametaphosphate and sodium fluorosilicate. Adsorption density studies indicated that the adsorption density of sodium hexametaphosphate on diaspore is much higher than that on silicate minerals at the concentration of 75 mg/L. FTIR spectroscopy studies show that sodium hexametaphosphate interacted with the Al atoms exposed on the diaspore and silicate minerals surfaces to form P?O?Al bonds through the P02 groups. It is possible that sodium fluorosilicate interacted through F- or [SiF6]2- with silicate minerals surfaces based on the analysis by AES.

Jan 1, 2006

By Patty Simpson, Sarah Benson

In an effort to improve consistency across the nuclear industry, over the past 10 years the Canadian Standards Association has developed a series of standards related to environmental management at Class 1 nuclear facilities and uranium mines and mills. Canadian uranium mines have been required by the Canadian Nuclear Safety Commission to align their existing monitoring programs with these standards. Orano’s McClean Lake Operation’s monitoring program, which was originally presented in the Environmental Impact Statement in 1991, has evolved through regulatory change, new scientific understanding, additional projects, and experience into a comprehensive set of monitoring requirements for effluent, groundwater, air emissions, and the receiving environment. The exercise of aligning the existing practices with the standards provided an opportunity to review and rationalize the entire program. To document the process the original “Environmental Monitoring Program Design Document” was restructured and developed as both a repository for historical information and monitoring rationalization, and also to be a living document describing on-going studies and supplementary work that are outside of the regular environmental monitoring program and may justify future changes to the program.

Jan 1, 2020

By K. Niboucha, M. Zergoug, S. Brick-Chaouch, H. Houali

"Corrosion is an electrochemical process that causes degradation and deterioration of various steel works (pipelines, drains, cisterns) whether they are buried, immersed, or not. Worldwide, we estimate that corrosion destroys a quarter of the annual production of steel at a rate of 5 tons per second. Several techniques are used to protect against corrosion. Among these processes, Cathodic protection, which is regarded as the best technique to assure the protection of steel, works against this phenomenon. This is achieved either by a system of reactive anodes, or by the technique of impressed current protection or other techniques. Before any installation of cathodic protection, a preliminary study and pre-evaluation of certain parameters must be made. In the present work, we will present an example of dimensioning of an installation of cathodic protection by imposed current of a pipeline using solar energy, where we discuss the following items:•,Evolutions of the potential as well as current along the pipeline and their respective expressions deduced from the laws known as telegraphists;•,Range of protection (potential of protection along the pipeline);•,Influence of the isolation resistance of the coating on the range of protection;•,Effect of the aging of the coating and its influence on the current of protection."

Jan 1, 2005

By S. B. Mishra

Ni-20Cr metallic coating was deposited on a Ni-based Superalloy (3Fe-19.5Cr¬0.3Ti-Balance Ni) by a shrouded plasma spray process; NiCrA1Y was used as a bond coat. Erosion studies were conducted on uncoated and plasma-spray coated superalloy specimens using an air-jet erosion test rig at a velocity of 40 m/s and impingement angles of 30° and 90°. The coating has been characterized for porosity, microhardness and microstructure and X-Ray Diffraction (XRD). An electron probe micro analyzer (EPMA) was used to obtain X-ray elemental mappings of the coating along the cross-section. Scanning electron microscope (SEM) with EDAX attachment was used to analyze the eroded surfaces.

Jan 1, 2005

By Frank Lemy

This paper presents an application of digital face mapping in an underground mine. Based on photographs it was possible to construct discontinuity maps, which were used to characterise the rock mass. The results were compared favourably with values obtained through scanline and area sampling mapping for the same site. The case is made for digital mapping as a safe, fast, and efficient way to characterise rock mass structure for engineering purposes.

May 1, 2001

By M. Bozorgtabar

Metal Matrix Composites (MMC) have a ductile matrix containing ceramic particles, Due to their improved wear properties, Al?SiC composites have economical applications in many industrial uses where wear is a problem, One of the most serious difficulties in manufacturing Al-SiC composites is obtaining adequate 'wetting' of the particles by the melt. In this research work, a stir casting system was designed for the improved manufacturing Al-SiC composites, The effect of some production variables such as the addition of SiC particles to the aluminum melt on wettability, was also studied. The results showed that the manual addition of particles would not be successful in manufacturing and that a system of adding silicon carbide particles through controlled temperature, atmosphere and improved mixing was needed.

Jan 1, 2005