Search Documents

By P. J. van Staden

Several differences exist between the columns used for laboratory simulations of heap leaching and commercial heaps. Column walls support part of the weight of the ore and restrict the particle packing arrangements. Columns are typically of a diameter that is smaller than the dripper spacing to be used on the commercial heaps. The stacking practices that cause segregation and stratification on heaps are absent from columns. Intuitively, these physical differences would be expected to be the reasons behind the observed differences between column and heap leaching performance. But how can they be quantified, and what is the magnitude of the differences? Could some of these differences be built into column leaching experiments in order to better simulate commercial-scale heap leaching performance to ease the scale-up calculations from column leaching data? Alternatively, could heap construction practices be improved so that the ideal performance obtained in columns could be emulated on heaps? Data from a few heap leaching cases studies that permit direct comparisons between column and heap leaching performance is analysed, to reveal the extent of the differences in resistance to mass transfer. Discussion is provided on the implications for column and heap leaching practice, and for scale-up design procedures. INTRODUCTION Differences have been known to exist between leaching performance observed in laboratory columns and that of commercial-scale heaps. Both the heap leaching kinetics and finally achievable extent of extraction are generally found to be inferior in heaps compared to that achieved in columns. Heap leaching design engineers extrapolate the anticipated heap leaching performance by multiplying the time-axis of a column-leaching curve by a factor of about 2 and the extraction-axis by a factor of about 0.8, as explained by Jansen and Taylor (2002), Scheffel (2002), John (2011) and Scheffel, Guzmán, and Dreier (2016). The procedure is illustrated in Figure 1 by means of a hypothetical example. The solid line represents the leaching performance observed in a laboratory column, and the dashed line represents the anticipated leaching performance of a heap, extrapolated from the column leaching data using these empirical scale-up factors.

Jan 1, 2019

By V. I. Lakshmanan

Rare earth elements and yttrium (REEs+Y) are being used in the making of hybrid electric cars, catalytic converters, wind power generators, LEDs, hard disc drives, flat panel displays, and portable electronics. Currently China produces more than 95% of REEs+Y, which has made REEs+Y a critical strategic resource. Process Research ORTECH Inc. (PRO) has developed the innovative mixed-chloride (HCl+MgCl2) solvent extraction processes for recovery of REEs+Y from their ores. The HCl leaching system provides the opportunity to regenerate the acid, while the presence of MgCl2 in the lixiviant enhances the activity of the hydrogen ion by orders of magnitude, making the lixiviant very aggressive and resulting in high recoveries of REEs+Y. Solvent extraction steps are used for separation and purification of REEs+Y from other value metals or impurities including iron, zirconium, hafnium, uranium, thorium, niobium, tantalum and titanium. Direct individual separation of REEs+Y in a mixed chloride system allows avoiding the additional process steps of precipitation and dissolution in HCl. The resulting process has a simplified flow sheet that is closed-loop and environmentally friendly.

Jan 1, 2014

By Alexander Levran

The main thrust of this presentation is to illustrate the growing contribution of solar energy to the mining industry by replacing existing mechanical and pneumatic tools and equipment with more effective and efficient electrical tools due to the increased efficiency and lower cost of solar energy generation. LCOE (levelized cost of energy/electricity) for solar energy is becoming highly competitive with other conventional sources of energy. The distributed architecture of solar power plants allows the supply of energy to highly remote and abandoned geographies. We will focus on the trend for this contribution to the mining industry over the next three years. Water desalination and delivery to the mining area will be topic of discussion regarding the contribution of solar systems in Latin America (LATAM) and other geographies. INTRODUCTION Increasing price pressure on the mining industry has generated a strong interest for mining companies to investigate energy costs and consumption. Currently, energy costs in mining economics contribute15% to 25% of the total commodity cost. In the past, most mines were operated by diesel gensets. Very high logistics costs for diesel supply, high and fluctuating diesel prices and theft led to very high energy prices. To overcome this problem, the mining industry has turned to solar energy, employing two main solutions: (i) adding a small scale (single level MWp energy supply) solar to an existing diesel system to create a hybrid solution operating as a microgrid environment; and (ii) replacing the existing diesel system with a large scale grid connected photovoltaic system financed by utilities or private IPP owners that signed a long-term power purchase agreement (“PPA”). In both applications, the near-term trend is to add storage and weather controls to optimize the electrical performance of the system. Use of concentrated solar solution (CSP) in the past was employed in a few remote sites to provide electrical energy to the mines. Currently this technology is not competitive with the photovoltaic (PV) systems. In some installations we have seen usage of a small hybrid system that is designed as relocatable, containerized and delivers scalable electrical power. In addition to the evolution of electrical energy sources, we see the trend of reduction of energy consumption in the mines by optimizing energy efficiency and generating load shifting solutions. Many studies of electrical energy in the mining industry support the growth of this trend in the mining industry.

Jan 1, 2019

"This paper discusses the use of risk assessment and risk management techniques within the Australian underground coal mining industry, within the context of geotechnical risk. The industry works within a pro-active, “enabling” legislative framework, where companies and management apply a range of risk assessment tools as part of their everyday management processes. Different geotechnical risk factors and approaches are reviewed, together with application examples – ranging from mine planning and design, operations, and accident investigations.A particularly powerful resource in each of the above stages of geotechnical management is the RISKGATE system. RISKGATE is an assembled “body of knowledge” structured under different topics across the Australian coal industry, of which three topic areas address rock mechanics issues for both the underground and surface mining sector. This paper will provide an overview of RISKGATE in the context of risk-based rock mechanics applications in underground coal mining."

Jan 1, 2015

By Lee Nichols

The Oil Sand Industry in northern Alberta, Canada, disposes of the by-products of bitumen extraction into tailings ponds. The mix of tailings sand and mature fines, with gypsum added as a flocculent, constitute a waste stream called Consolidated Tailings or Composite Tails (CT). The two main challenges of the tailings disposal process are a chronic shortage of economical containment and the potential mobility of CT deposits in the event of breaching by, for example, long term erosion, which makes abandonment of tailings ponds more complicated. Thick deposits of CT do not consolidate in adequate time to provide reassurance for abandonment of the CT containment facilities and that is why the containment must be adequately robust or the properties of CT improved for long term stability. This paper addresses potential solutions to these problems by applying the gravity drainage of CT and quasi-homogeneous construction for containment facilities. Gravity drainage is suggested as a mechanism to facilitate the consolidation of CT in critical areas of the ponds by inserting internal sand layers within the body of the deposit. Critical CT areas are defined as areas around the perimeter of containment. The advantages of this solution are long-term stability of the disposal area by creation of stiff deposits around its perimeter and facilitation of reclamation efforts on its surface. The present solution for containment of CT deposits is not favourable from a materials balance point of view. In general, sand has become a valuable resource as it both forms the primary component of the CT matrix and becomes the containment building material. If sand is required for CT, less is available for dyke construction. This puts additional pressure on the industry as a whole to maximize the use of overburden and interburden for construction of tailings containment structures. Typically, only 50 percent of dry mine waste (overburden + interburden) is incorporated into dyke construction. The remainder of dry waste is stored either in waste dumps or in tailings ponds, consuming valuable in-pond space originally allocated to CT material. Quasi-homogeneous dykes are proposed to contain CT deposits rather than traditional minimum cross-section dykes built of overburden and/or cell sand. The quasi-homogeneous dyke may change the unfavourable material balance and lessen the construction constraints that are presently imposed on the mine/waste disposal process.

May 1, 2004

By Z. Q. Yue

Many large rock avalanches and/or landslides have occurred in mountainous regions around the world. Their occurrences are normally rapid and unexpected, which can cause disasters. They have been investigated extensively by many researchers and engineers since the 1903 Frank Slide on Turtle Mountain, Alberta, Canada. They are one of the most peculiar phenomena because the rock debris of more than one million m3 can move over the horizontal distances exceeding those expected from conventional friction physics. This paper presents a gas cause hypothesis responsible for the large rock avalanches. It is the migration and expansion of a certain amount of highly pressurized and dense natural gas mass from deep geological grounds into the mountainous rock mass slopes. The natural gas with high pressure and density can escape from the deep geological ground and flow through faults, weak zones and/or porous channels into the rock mass forming a mountainous slope. The rock mass forming the slope has the high tensile and compressive strength and can resist the initial loading of the gas mass migrated into and stored in their voids, pores, holes, gaps, openings, apertures and cavities. With time, more and more gas mass from deep ground can migrate into and stored in the slope rock mass. Eventually, the peak equilibrium of forces and deformation reaches. The expanding power of the gas in the slope rock mass would instantly and rapidly break, erupt and/or explode them. The compressed and dense gas mass would mix, flow and expand together with the broken rock debris mass and continue offering their remaining expanding powers to the moving and sliding debris mass. As a result, the rock debris of large volume can reach the runout distances exceeding those expected from the conventional friction physics. The gas would escape into the sky and the solid rock debris would remain on the ground spreading over large ground area. The 1903 Frank Slide is examined to show this gas cause and mechanism in mountainous regions.

Jan 1, 2015

By C. W. Chao, M. Melashvili, F. Hilário

The processing of a bulk concentrate containing copper as chalcocite, enargite, bornite and chalcopyrite along with pyrite and precious metals of silver and gold was studied. A leaching study was undertaken to examine the application of the atmospheric acid leaching process to a bulk copper concentrate for copper recovery followed by cyanidation or thiosulfate leaching for gold and silver recovery. The extraction of copper exceeded 90% under some conditions and the recovery of gold and silver reached a maximum of 44 and 45%, respectively. A sample of bulk concentrate was roasted in air to oxidize the sulfides with release of sulfur dioxide followed by acid leaching of the roaster calcine and cyanidation of the acid leach solution. The copper extraction reached over 92% and the gold extraction exceeded 88%. The sulfur dioxide may be captured for acid production. INTRODUCTION The processing of a large primary copper deposit in Indonesia is under investigation. One of the possible routes for processing involves flotation of a bulk copper-gold concentrate followed by treatment by an atmospheric leach/SX-EW process for copper recovery. The atmospheric leach residue would then be leached for recovery of gold and silver. A second route involves roasting of the concentrate followed by acid leaching and SX-EW for copper recovery. The leach residue from the roaster calcine would then be leached for recovery of gold and silver. The roaster off-gases could be used for sulfuric acid manufacture, enabling the production of a valuable by-product. The Cobre Las Cruces (CLC) process (Munoz, Garcia, & Delgado, 2017) was designed to treat a resource of copper discovered close to Seville, Spain. The process was developed by Outotec with MK Gold (original project owner). INMET Mining subsequently purchased the deposit from MK Gold and built the copper processing facility. The CLC process is similar to the Mt. Gordon Copper process; except that OKTOP reactors have been installed instead of a low temperature, low pressure autoclave process. The plant was designed to treat 1.3 mtpa of ore at a grade of 6.2% Cu to produce 72,000 tpa of cathode copper over a 15 year project life. The main gangue mineral at Cobre Las Cruces was pyrite. The Cobre Las Cruces ore is therefore similar to a rougher flotation concentrate containing copper minerals and pyrite. The roasting of a rougher flotation concentrate can be designed to produce hematite, basic copper oxides and sulfur dioxide off gas. The acid leaching of the basic copper oxides may produce soluble copper for SX-EW recovery of copper. The sulfur dioxide off-gas may be used to make sulfuric acid.

Jan 1, 2019

By S. McCarthy, K. E. Waters, A. Jordens

The beneficiation of rare earth (RE) element bearing minerals has become an active area of research as applications for these elements grow while the supply to non-Chinese consumers is restricted by export quotas. One of the most interesting beneficiation techniques for RE minerals is froth flotation as their unique chemistry suggests that collectors with a specific affinity for RE cations should be able to selectively recover these minerals. Existing literature, focusing mainly on bastnäsite flotation, identifies hydroxamic acids as excellent collectors for RE minerals. The high stability of hydroxamate-RE cation complexes is the explanation most often offered for the observed selectivity of these reagents in bastnäsite flotation however some research has also suggested that mineral solubility plays a crucial role in the success of hydroxamic acid flotation of RE minerals. This work investigates the interaction of allanite, a relatively insoluble RE-silicate mineral, with benzohydroxamic acid using zeta potential measurements and microflotation. The effects of Fe(III) and Fe(II) ions as potential activating ions (cations that form stable hydroxamate complexes) on benzohydroxamic adsorption to the allanite surface are investigated as a potential solution to promote hydroxamic acid adsorption. The results indicate that the optimum conditions for separation of allanite from quartz occur at pH 4 using FeCl2 as an activator for benzohydroxamic acid adsorption.

Jan 1, 2014

By John Eggert, Paul Benford

"Since 1982, Placer Dome Inc. -Dome Mine has steadily increased mill throughput. Tonnage has increased from a nominal design capacity of 3000 short tons per day, attained in 1985, to 4130 stpd by the end of 1992. Many minor and major circuit adjustments were tried to maximize tonnage.Having utilized most conventional means of increasing tonnage, further increases required a newer approach. This paper discusses the Dome experience in the development and implementation of an expert system.The Comdale/C system was chosen for a controlled trial. The criteria for acceptance were: increased tonnage had to be sufficient to pay for the system; the increase had to be visibly sustainable and the mill operators had to be willing to accept the system.The criteria for purchase were met during the trial and the system was purchased. The system continues to perform well. The tonnage throughput increase has been sustained while operator acceptance remains high.IntroductionPlacer Dome Inc. -Dome Mine is Canada's oldest operating gold mine. The mine was among the first established in the Porcupine camp in what is now Timmins, Ontario. The City of Timmins is located approximately 500 miles or 800 kilometres north of Toronto. Figure 1 shows a map of the province of Ontario and the mine location.In 1912, milling began at a rate of 350 short tons per day. With two minor exceptions, milling has been continuous since this time. The first of these shut downs was in 1918 during the first world war. The war created labour shortages which forced the mine to stop production for more than a year. The second was in 1930 when fire destroyed the mill."

Jan 1, 1994

By G. E. Rodger, R. Jugoon

"SUMMARYSamples of Aunor gold precipitates which varied widely in gold content were fluxed to produce a bisilicate slag with various oxidizers and combinations of oxidizers. On the basis of some preliminary tests a flux composition was chosen which appeared to show the most promise.The different components of this flux were then incorporated into a matrix for a 23 factorial design experiment to determine what were the most important variables and what changes should be made to the flux composition to optimize the resultant total bullion fineness.The results of the 23 factorial design experiment showed that the flux composition as calculated was very close to an optimum as only very minor changes were required to give bullion in excess of 995 fine.INTRODUCTIONEarly in 1969 the results from the Aunor Gold Mines refinery showed that wide variations existed both in precipitate grade and in total bullion fineness. An analysis of this data showed that as the precipitate grade increased, the gold bullion fineness also increased (see appendix 1). Therefore, to improve the refinery results test work was initiated to: 1) improve the precipitate grade and 2) to determine, with the help of statistics, a flux composition which would be able to handle wide variations in precipitate grade and give a total bullion fineness in excess of 950 fine."

Jan 1, 1970

By Don Ritz

Smart leaders focus on safety even in tough times. Businesses that retreat into survival mode and ignore safety do so at their peril, risking loss of employee and stakeholder confidence and exposing themselves to financial and reputational loss they can ill afford. It?s a moment of truth when employees and stakeholders learn whether safety is truly your priority or just a convenient cliché for good times. Visionary leaders who build safety culture even in a downturn maintain people?s trust, prevent loss, and position the organization for enhanced success as times improve. Safety is the right business focus in good times and bad.

May 1, 2009

By Larry M. Southwick

There have recently been executives at major metals companies who have recommended that Greenfield Projects not be pursued. Greenfield includes not only new geographical locations, but also new technologies and new types of feed materials. In the middle part of the 20th Century, two such projects were successfully commercialized to recover nickel from Cuban lateritic ores. One project (at Nicaro) used the Caron ammonia-ammonium carbonate leach and the other (at Moa Bay) a high pressure acid leach. How both of these projects dealt with these Greenfield issues will be reviewed, based on the original reports that described the research and development of the plants. This study will include a review of the critical ore characterization and sorting issues, as well as the extractive metallurgical, product recovery and equipment selection and sizing problems and how they were solved at each stage of project development, from laboratory through one or more pilot scale plants to start up and operation. In one case, a major revision of the plant was made after several years of operation to correct operating, equipment selection and materials of construction problems that hindered economical operation. These descriptions will provide a guide through the complicated and critical issues that in recent times have caused many companies to give up on similar development. Even with the more advanced analytical and computational tools available to today’s mineralogists, engineers and metallurgists, the basic concepts with which these projects successfully addressed their sets of problems are still required. In addition, upper management, now perhaps further removed from hands-on experience than was common then, will see how complicated problems require intense and detailed effort to avoid failure in the field and capital blowouts. Build it and we will make it run, kicking the can down the road and borrowing operating and design concepts incorrectly on technological issues, or nine year olds on a sugar high making financial decisions are not philosophies by which to succeed with Greenfield Projects.

Jan 1, 2014

By B. Zhu

With the challenge of clearing steel production and increasing of the productivity of converter, the application of hot metal pretreatment technology in torpedo car become a key process in the steelmaking. In this article, the technologies, production and development trend of Al2O3-SiC-C bricks for torpedo cars in China are reviewed, the current application situation and main requirements for the Al2O3-SiC-C bricks are also addressed.

Jan 1, 2004

By L. K. Mireku

"Abstract - The Halfmile Lake South Deep zone, Bathurst Mining Camp, New Brunswick, was discovered by Noranda Inc. (Exploration) as a result of a 3-D seismic survey in 1998 and the subsequent drilling of ten diamond-drill cores. The deposit consists of massive, breccia, and stockwork Pb-Zn-Cu sulfide minerals, and is hosted by a volcano-sedimentary sequence belonging to the overturned Ordovician Tetagouche Group. Epiclastic rocks and interbedded fine-grained felsic pyroclastic rocks dominate the stratigraphic footwall. Locally, crystal-rich felsic tuffs and subordinate epiclastic rocks comprise the immediate stratigraphic hanging wall. The entire stratigraphic sequence was intruded by quartz-feldspar porphyritic intrusions, and cut by intermediate and basic dikes. The volcanic and sedimentary rocks can be discriminated geochemically using trace element ratios such as Zr/TiO2 and Nb/TiO2, despite intensive alteration and cleavage development. These ratios indicate that four protolith volcanic compositions exist: rhyolite, dacite, andesite, and basalt. The aphyric and feldspar- and quartz-phyric volcanic rocks are dacitic and rhyolitic in composition; epiclastic rocks have trace element ratios consistent with dacitic compositions. Pearce element ratio diagrams, general element ratio diagrams, and petrographic observations demonstrate that the rhyolitic volcanic rocks exhibit evidence of albite, potassium feldspar, and quartz fractionation, dacitic volcanic rocks exhibit little evidence of any fractionation, and epiclastic sedimentary rocks exhibit evidence of quartz sorting only. Hydrothermal alteration is best represented by the presence of phengitic muscovite and daphnitic chlorite. Minor calcite occurs in the stratigraphic hanging wall, deep in the stratigraphic footwall, and in post-mineralization dikes, and thus is not interpreted to be part of the causative hydrothermal event. Element additions and losses during alteration have been used to determine net alteration reactions, and these have been used to identify alteration parameters that are independent of other forms of alteration and fractionation/sorting, and which can be used to guide exploration. These parameters include: a bulk hydrolysis measure, (2Ca+Na+K-2CO2)/Al; a muscovite alteration measure, K/Al; an albite destruction measure, Na/Al; a chlorite alteration measure, (Fe+Mg-S/2)/Al; a chlorite composition measure, (Fe-S/2)/Mg; a sulfidization measure, S/Ti; and a carbonatization measure, CO2/Ti. With the exception of the carbonatization measure, these alteration parameters define a distinct lateral and vertical zone of intense hydrothermal alteration in the stratigraphic footwall of the deposit, and demonstrate that the epiclastic rocks are predominantly chlorite altered, and the volcanic rocks are predominantly muscovite altered. Within the alteration halo, element additions of Fe and H, and element losses of Na are characteristic. Potassium was added to muscovite-altered rocks, but subsequently removed from chlorite-altered rocks. The results from this study demonstrate that metamorphism and deformation have not significantly obscured hydrothermal alteration signatures."

Jan 1, 2006

Mining Impact in Water Quality: Understanding the conflict Mining is an industrial process Metal mines that chemically process ore to concentrate metals such as copper and gold use more water than non-metal mines such as coal, salt and gravel. Tailing Ponds Water contaminated with high concentrations of metals, sulphide minerals, dissolved solids, or salts can negatively affect surface water quality, aquatic ecosystems and groundwater quality.

May 1, 2013

By Y. M. Shneerson, I. V. Fomenko, M. A. Pleshkov, E. A. Ospanov, A. A. Shakhalov, S. S. Naboychenko

Low-grade copper concentrates (with copper content less than 20%) often contain impurities such as arsenic, zinc, lead, mercury, antimony and bismuth. The pyrometallurgical treatment of such concentrates is associated with several problems, which will ultimately affect the cost and the quality of copper cathodes as well as by-products. SRC Hydrometallurgy proposed a complex hydrometallurgical technology which allows the removal of impurities and the enrichment of low-grade copper concentrates to a quality which will be more suitable for pyrometallurgical processing. Laboratory batch tests and pilot plant results for the pressure leaching steps are shown in this paper. The key parameters of the leaching steps were determined and optimized. The quality of possible by-products were also determined. The developed flowsheet includes two pressure leaching steps: pressure oxidation (POX) and hydrothermal alteration (HTA). Both operations are carried out at 170°C with subsequent flotation of POX and HTA residues and recovery of copper, zinc and lead into separate concentrates for further processing. The development of the flowsheet was based on the Balkhash Zinc Plant (Balkhash, Kazakhstan), which had been non-operational since 2009. The developed flowsheet for processing of low-grade concentrates will utilize 80% of the existing equipment of the Balkhash Zinc Plant, thus leading to a significant reduction in required capital expenditure. INTRODUCTION As the age of copper mining operations advance, copper grades continue to diminish and impurity levels increase. Therefore, copper producers are forced to look for new innovative hydrometallurgical technologies which are able to handle low-grade raw materials and solve problems associated with impurities in an economically justifiable way. New technologies allow to extract valuable components selectively and to process low-grade concentrates which had previously been marked as non-technological and economically unviable. Hydrometallurgical technologies for processing of copper-containing materials can be divided into two main categories: chloride and sulfate (atmospheric, autoclave and bacterial) based technologies. Since the 1970s, many autoclave techniques for the processing of copper-containing materials have been developed and implemented (Naboichenko, 2002; Dreisinger, 2005; Habashi, 2009; Shneerson, 2011). The mineralogical composition of the ore (or concentrates), geographical location of the deposit, distance from industrial areas, availability of existing treatment facilities, availability of skilled labor, cost of electricity and cost of neutralization are some of the factors which are usually considered when the appropriate technology is selected (Halbe, 2002).

Jan 1, 2019

By Enzo Angeles, Desmond Nanchengwa, Lee Julian, Julian Ruiseco

Since the early 1980s, surface hard-rock mining companies have searched for a blast movement model to enable grade control optimization efforts. Significant time and money were spent attempting to create blast simulations to aid post-blast grade control. Despite nearly 40 years of effort, practical blast movement models remained elusive until computing power reached levels that make real-time simulation possible. From the mid-1990s, mines have been creating in-situ grade control polygons and translating the polygon nodes horizontally to account for blast movement. In many cases, objects are placed in the blast volume and located post-blast to provide local vectors for these node translations. This method was always a compromise between practicality (2D) and reality (3D), but it was the only viable solution that matched the needs of operations. This study considers 21 blasts and evaluates the incremental value achieved by new processes unlocked through 3D modelling, while investigating challenges, limitations, and opportunities for each method.

Jan 1, 2023

By G. V. Poropat

Roughness of a discontinuity may be an important factor influencing shear strength of the discontinuity. Traditionally, determining the roughness of a discontinuity surface and providing a numerical measure of the roughness has required considerable effort or specialised equipment. The development of new 3D imaging tools that are easy to use has provided effective fast and accurate means of creating 3D surface models from which roughness measurements can be readily obtained. These new techniques are versatile enabling a user to measure roughness along any desired profile and at any resolution up to the limit of the spatial subtense of a measurement on the discontinuity surface. This paper primarily reviews extensions to the use of 3D imaging that enable the measurement of roughness. Additionally we provide some examples of the measurements and examine some of the issues associated with extracting measures from the spatial data that will support estimation of shear strength.

May 1, 2009

By Fred G. Hewett

Cassiar Mine in northern British Columbia began development in 1952. The deposir is found on rhe west limb of rhe McDame Synclinorium in a Mississippian serpentinite body. The serpenltntte, one of the McDame l ntrusives, imrudes Sylvester Group . rocks, which comprise a Lare Devonian to Early M1ss1ss1pptan eugeosync/inal sequence of argillites, quarrzires and volcanics. The foorwall conracr berween Sylvester Group rocks and rhe serpenrinire is a marked zone of broken and incomperent argillite and graphitic schist. The less marked hang- 111gwall contacr 1s a band of indurated argillite. The JurassicCretaceous emplacemenr of the Cassiar Graniric Barholilh is responsible for mosr of the numerous )aims, faulrs and shear zones found in the serpentinite body. Faulting occurred borh before and after asbestos formation. Asbestos is mined from an open pit ar rhe rate of 4,535 ronnes daily. It passes from the pir along a rramline to the mill, where it is concen/rared into nine direcr milling grades. Packaged fibres travel ro over 40 counrries around rhe world for use in the texrile, cemenr and other industries.

Jan 1, 1984

By Rebecca L. Jones

The paper addresses the application of XPAC AutoScheduler at the Fort Hills Energy Oil Sands Project to complete fast turn around ?what if? scenario testing of different mine schedules. Traditional scheduling approaches involve engineers making a ?best guess? at the required mining sequence, loading this sequence into a scheduling package and testing the results to determine if the schedule meets corporate objectives. This process is iterative and can be very time consuming. Autoscheduling techniques, on the other hand, are based on the engineer pre defining the mining rules and constraints of the deposit. The software then automatically selects a sequence of mining which the schedule should try and achieve, based off specified corporate objectives. Under this system the engineer is able to adjust the objectives and rules to evaluate numerous scheduling scenarios quickly and easily. An XPAC AutoScheduler model was built, documented, and implemented by Runge and Petro-Canada Oil Sands Inc. personnel in a month. It is currently being used by Petro-Canada Oil Sands Inc. to run multiple schedule scenarios, most taking less than ten minutes configure and ten minutes to schedule. The results of each schedule are tabulated with supporting graphs on; the bitumen grade profile, strip ratio, ore inventories and mined tonnage. In addition to this, the block model may be animated to show the progression of the resources mining the schedules.

May 1, 2008