Search Documents

By C. E. Baltzer

This is the fourth in a series of coal technology reviews being prepared. in accordance with a recommendation voted by the Coal Division C.I.M. in session at the Jubilee Meeting, Vancouver, 1948, that the Department of Mines and Resources be requested to arrange for publication by the proper Government authority of a Quarterly Review of Coal Technology for distribution among those concerned in the production and use of coal in Canada. Copies of the first review, which appeared in the November, 1948, BULLETIN, pp. 612-614, of the second review in the June, 1949, BULLETIN, pp. 272-275, and of the third review in April, 1950, BUL-LETIN, pp. 1,9?3-196 (also, respectively, in Transactions, Vol. LI, 1948, pp. 262-264 Vol. LU, 1949, pp. 117-120, and Vol: LIU, 1950, pp. 133-136), were distributed by the Dominion Coal Board and are still available on request. In this review, the first in the series in the field of combustion, development and trends during the period approximately from World War II to the present time are described and therefore the presentation is general. Later reviews will particularize developments in relation to the range of coals available in Canada.-ED. INTRODUCTION THE utilization of coal in heat and power producing equipment has become of paramount importance to the coal industry in maintaining stable and profitable markets. In the past, the chief concern was with mining, transportation, and overall supply problems, but modern conditions demand interest in and knowledge of all phases of the product, from coal in situ to its ultimate disappearance in the form of products of combustion. Even the last mentoined factor has caused complications, as is shown by current widespread activity in the field of smoke abatement

Jan 1, 1951

By S. Banisi, M. Pourkani, A. Kargar, D. Hamidi, M. Sarvi

"Flotation circuit of the Sarcheshmeh copper mine, which processes 40,000 t/d of ore at 0.9% Cu, consists of rougher, cleaning and recleaning stages. To study the stage recovery of copper, one of the eight identical flotation banks was selected for sampling. It was observed that 17% of copper goes to the tailings and the lowest copper recovery was for particles coarser than 105 microns. The third five-cell unit of this bank not only did not recover appreciable amount of copper but also decreased the concentrate grade. The grade of the last five cells was lower than the feed grade suggesting that mixing of the concentrates of the three units was not beneficial. To alleviate the problem, the concentrate of the first four-cell unit was directed to the cleaners feed box (i.e., by- passing the regrind mill). This increased the overall copper recovery by 1.7 %. Also rather than the current practice of adding the reagents only at the feed tank (i.e., 100-0-0%), various combinations of stage addition were examined. It was found that 75-25-0% addition regime could increase the total copper recovery by 1.3%. At the recleaning stage in order to increase the final copper concentrate grade, a froth washing system was used. To ease the maintenance of the system, a shower type washing system was installed. The optimum wash water superficial flowrate was found to be 0.06 cm/s. Continuos sampling of the recleaners with and without wash water over a period of two months showed an increase of 1.5% in the final copper concentrate grade at constant overall copper recovery.INTRODUCTIONThe Sarcheshmeh copper ore body that may rank as third or fourth largest in the world contains 1 billion tonnes averaging 0.9% copper and 0.035% molybdenum. It is located in southeastern Iran and has been processing 40 000 t/d of ore since 1982. The mine produces 100 000 tonnes of copper and 2200 tonnes of molybednite concentrate per year.After three stages of crushing, the ore with a F80 (80% passing size) of 12.7 mm is fed to eight parallel ball mills in closed circuit with cyclones to produce a product 70% finer than 75 microns. The concentrate of rougher flotation circuit is ground; rougher tails constitute the main component of the plant final tailings. A concentrate with an average grade of 31% Cu (chalcocite and chalcopyrite) is obtained after cleaning and re-cleaning stages. Total recovery of the plant varies between 83% and 87%, depending on operating conditions and ore type."

Jan 1, 2001

By Mark Fernald, Christian O’Keefe, John Viega

"In this presentation, the SONARtrac™ technology platform will be described. CiDRA's proprietary clamp-on, passive sonar array-based flow meter technology performs two independent measurements – flow rate and fluid characterization. Firstly, the meter provides the volumetric flow rate of the mixture by measuring the speed at which naturally occurring turbulent structures convect with the flow past an axial array of sensors. Secondly, the meter uses similar sonar-based processing techniques and naturally occurring sound in the process fluid to measure entrained air levels. The result is a unique ability to measure the flow rate and entrained air level of most fluids – clean liquids, high solids content slurries, and liquids and slurries with entrained air.Also to be presented is the application of the sonar-based technology platform in a variety of oil sands processes, hydrotransport, and minerals beneficiation applications. In particular, difficult slurry flow measurement and control in the areas of comminution and flotation such as mill discharge, hydrocyclone feed/overflow, final concentrate, thickener discharge, and tailings will be discussed. In addition new real time maintenance free process measurement capability will be presented in the areas of entrained air in slurry, collection zone gas holdup (?g), and slurry velocity profiling. The operational advantages and value of these measurements, even in the presence of scale buildup, will be discussed.INTRODUCTIONFlow measurements in the mineral processing and oil sands industry suffer from the limitations placed by previously available flowmeters including the commonly used instruments such as ultrasonic meters, magmeters, turbine meters, orifice plate meters, vortex flow meters, Coriolis flow meters, and venturi meters. The desire or requirement to make a non-contact measurement that is accurate and robust, and can be performed on practically any type of fluid within practically any type of pipe has driven the creation of a new class of flowmeters. This new class of flowmeter technology utilizes sonar-based processing algorithms and an array of passive sensors to measure not only flow, but also fluid composition."

Jan 1, 2007

By Corrie Pitzer

Safety performance in many companies and even industries has stalled in the last decade. Accidents rates are improving but more slowly and yet, serious accidents and fatality rates are not: in fact, these rates of more serious incidents have plateaued or deteriorating. In more dramatic cases, organizations that had ?exemplary? safety statistics, suddenly had a catastrophic or multi-fatality event occurring. Popular books such as In Search of Excellence of Peters and Waterman or Good to Great of Jim Collins created many delusional ?secrets? or recipes, to achieve great performance and yet, most of those ?great? or ?excellent? companies have now declined in their performance, some dramatically and some have fallen from grace, like Fanny Mae, a company Jim Collins identified as a ?great? one, that had to be bailed out in the latest financial crisis. These organizations share several ?delusions? about managing a business, and often, these delusions are created by academics, consultants and authors of popular books about (safety) management. More damaging however is that safety management is defined by a set of key practices or axioms: a focus on human error, compliance to rules and regulations, creating consistency of systems and actions, reacting to accidents and incidents and on prevention of those, measuring safety with performance metrics and rewarding employees on those measurements. All of these axioms contain the seeds of destruction, and they create conditions and dynamics that precede the disaster - and ironically, they are all 'good things' we do in safety management. For example, a mere focus on safety in the business, and the measurement of it, create a culture of repression of mistakes and incidents, leading to a situation where the organization knows incrementally less and less of risks and risktaking behaviour - until the day it all coincides destructively! This paper discusses seven such safety delusions and how they impact on the views and safety management approaches. They are: ??The delusion of (risk) control, that risks can actually be identified, analyzed and mitigated. ??The delusion of compliance, that mere compliance to rules will safeguard the business ??The delusion of consistency, that standard operating procedures will ensure safe operations ??The delusion of predictability, that accidents and trends tell us everything about the risks of the future ??The delusion of human error, that people are the weakest link and that it can actually be dealt with through discipline and enforcement. ??The delusion of statistical trends, that safety is measurable with statistics ??The delusion of invulnerability, that we have achieved high levels integrity and capability to deal wit risks. Organizations that suffered catastrophes all share some or all of these delusions and this paper traces how these played a role in many disasters, ranging from the Titanic, Challenger, Piper Alpha, Bhopal, BP Deepwater Horizon and many more.

Aug 1, 2013

By Raj K. Rajamani, Sanjeeva Latchireddi, Dave Plummer, Stieger. Julius

"The Cortez SAG mill liner design was recently modified to improve the mill operating energy efficiency. In addition to the expected benefits, the design change unexpectedly played a significant role of verifying the proposed grinding circuit expansion for the Cortez Hills project as well as illustrating current SAG mill bottlenecks. This paper will discuss the evaluation that addressed operator and maintenance observations, historical PLC data, and “crash stop” observations to calculate charge motion, packing between lifters, and slurry transport through grate and pulp lifters. The performance of the new shell and discharge end liner design will also be discussed as well as their role in the possible grinding circuit expansion.INTRODUCTIONCortez Gold Mines commenced operation in 1969 with its Mill #1 rated at a nominal 2,000 tons per day. Mill #1 was a conventional rod mill/ball mill circuit followed by an 8-stage CIP circuit. In the early 1990s the Pipeline deposit was discovered and subsequently Mill #2 was built to process the increased ore volume. Mill #2, commissioned by mid-1997, was a nominal 10,000 tons per day SABC circuit followed by an 8-stage CIL circuit for oxide gold ore. Operating and commissioning details of this plant have been published elsewhere (Powell, 1998). By late 1998, there was not enough ore volume to support both mills so the smaller, higher operating cost Mill #1 was put under its current care-and-maintenance status. A simplified flowsheet of the current mill is shown in Figure 1."

Jan 1, 2007

By Terry A. Kirk

"This paper describes Derrick High Frequency Vibrating Screens and their process performance in grinding circuit applications. The benefits of screen sizing in closed circuit grinding are illustrated by case histories from a wide spectrum of mineral industries.INTRODUCTIONHigh capacity, reliable wet screening equipment is increasingly in demand by the mining and allied industries for separations finer than 1/.7 5mm (I/ mesh). The continuing search for improved energy efficiency and reduced steel consumption in comminution has Jed to greater scrutiny of every aspect of circuit design and operation, including the classifier efficiency (selectivity) function.Derrick Manufacturing Corporation has been developing high frequency screening machines designed specifically for grinding circuit applications since 1973. Successful installations are currently operating in iron ore, copper, coal, uranium, phosphate and other extractive industries."

Jan 1, 1984

By John Wilson

"The unconformity beneath 75 per cent or over 6000 km2 of the Athabasca Basin in Alberta lies within economically exploitable depths. The basement beneath this unconformity consists of an extension of the Wylie Lake Pluton, locally faulted and containing areas of mylonitic rocks. While the rocks of the Wylie Lake Pluton are not promising host rocks for uranium ore deposits, the areas of mylonites, graphitic rocks and possible remnants of granitegneiss would bear closer examination. One area of maficmylonites shows a weathering zone enriched in Si, Ca, Na, Pb, Ni, Ba, Co, Sr, Zn and U in addition to reported values of 0.08 oz/ton gold. This zone occurs beneath 800 m to 900 m of Athabasca Group sediments, but similar rock types are present beneath much thinner cover elsewhere. Detailed geophysical exploration is required over the area of thinner Athabasca Group rocks to define more precisely the areas of promising basement rock type.IntroductionThe Athabasca Basin in Alberta has considerable economic potential which has not yet been realized. The geological setting is closely analogous to parts of the basin in Saskatchewan which host major uranium deposits. Recent advances in geophysical techniques have led to deposits being located in Saskatchewan below 600 m of cover. This means that the unconformity between the Athabasca Group and the basement lies at exploitable depths over 6000 km2 or 75 per cent of the Alberta portion of the basin. Much of this area was only cursorily examined almost a decade ago. In addition, Alberta's new Metallic Mineral Regulations have clarified the regulatory situation in the area, and opened up much land for exploration. This article is based on Wilson's (1985a) study of the Athabasca Group and Wilson's (1986) work on the basement and alteration beneath the Athabasca Group in Alberta."

Jan 1, 1987

By H. Ranjbar

The Darrehzar porphyry Cu deposit is situated in the Urumieh-Dokhtar magmatic suite of Central Iran. The REE and trace element data suggest that the deposit lies within a continental margin setting. Phyllic and propylitic alteration are pervasive in the area but potassic and argillicalteration are not readily recognized on the surface. This is possibly the result of super gene weathering of the surface rocks or because of an intense phyllic overprint. Poor soil development and abundant outcrop make the area suitable for a case study of lithogeochemical exploration technique for Cu deposits. A total of 262 rock samples was collected over the area and analyzed for 15 elements. The geochemical data cor-relate with the mineralogical composition of the rocks with the phyllic zone being marked by high-er concentrations of Si, Al, K, and by a high sericitization index while Ca, Mg, Sr, total Fe and Mn are more abundant in the propylitic zone. The lithogeochemical study indicates a metal zonation from a Cu + Mo-rich core to a Zn + Pb ± Ag-rich outer zone. Principal component analysis is useful for separating element associations, which in turn reflect the alteration halos. Principal components 1 and 2 depict alteration zoning, where-as 3 shows an association of Cu and Mo, that roughly defines the mineralized area.

Jan 1, 1997

By J. H. Archibald

"IntroductionShot-saws are used for sawing rock throughout the dimension stone industry especially in granite quarry mills. Shot-saws, as currently designed, have an inherent wear problem which leads to slow cutting rates and repetitive blade changes which consumes much time. Because the saw blades are made from steel the abrasive shot used with them is limited to a certain hardness which effects the over-all efficiency of the sawing operation. Suggestions are made toward optimization of blade design and the sawing process. Blade DesignA common steel blade design is shown in Figure I. Note the perforations in the blade. These perforations or holes in the blade serve two or three purposes. The most obvious reason is to allow the abrasive shot a pocket in which to collect at the bottom of the blade, so that it can be distributed from these pockets into the cutting zone underneath the blade. The abrasive is fed to the saw in a slurry and usually comes in from the top. The blade must then cut a kerf wider than itself in order that the abrasive grains have a path leading from the top of the blade, down along its sides, and finally reaching the pockets and cutting zones. This circuitous path followed by the abrasive leads to side wear on the blades and high friction which can lead to blade buckling in severe cases. However, the fluidized path of the abrasives down the sides of the blade serves another purpose which is a positive gain if conditions are properly controlled. The abrasive slurry interacts with the perforations of the blade, the blade itself and the rock. This gap and the perforations in the blade, which are fluid filled, are sites of constant shearing motion. Eddy currents form in these gaps and pockets which tend to stabilize the blade by setting up balanced hydrodynamic forces which otherwise might not form in a non-perforated blade. A stable blade produces a more uniform cut in the rock. The third and final reason for the perforations are to allow the blade to wear in such a fashion that new pockets are always being formed and, consequently, new cutting surfaces between these pockets are also formed."

Jan 1, 1993

By J. J. Brummer

The possibility of diamonds occurring in Canada was first raised by W. H. Hobbs in 1899, who concluded: "that the apex of the fan of diamond distribution probably lies somewhere in the strip of the territory bordering James Bay on the east." This was based on the occurrence of diamonds in surficial sediments at various locations south of the Great Lakes. There are two recorded discoveries of drift diamonds in Ontario: (a) the Peterborough Diamond, 33 carats in size, poorly documented and found sometime before 1920;and (b) the Jarvi Diamond, 0.255 carat, found during 1971 in Sheraton Township near Timmins . Both discoveries were in surficial sediments and their source(s) have not been located. During 1960, Selco Exploration Company Ltd. started a heavy-mineral sample program of river gravels in the James Bay Lowlands of Ontario. This was continued by Canadian Rock Company Ltd. (1962-1963) and the Ontario Division of Mines (1973). The surveys discovered the presence of kimberlite minerals in gravel samples from streams draining the Moose River Basin. A total of 53 pyrope grains, four magnesian ilmenites and one grain of chrome diopside were identified from 32 sample locations. A study of the distribution of these minerals suggested the kimberlite source rocks to be located along the north margin or within the Kapuskasing gravity "high" in the area immediately south of James Bay. The Jarvi Diamond, found on an esker east of Timmins, could well have originated from this area. During 1965, an esker was sampled by the Geological Survey of Canada, and the results attracted attention to the area south of Lake Abitibi. At 9 out of 34 sites sampled along the Munro esker, Lee recorded the presence of pyrope garnets and very minor chrome diopside.

Jan 1, 1978

By Daniel Hodouin, Claude Bazin, René del Villar

"A traditional linkage has long been established at Laval University's Department of Mining & Metallurgy between the Mineral Process (MP) and the Mining Exploitation (Min) on one hand, and between the Extractive Metallurgy (EM) and the Materials Engineering (Mat) on the other. This academic separation of Mineral Processing from Extractive Metallurgy at the educational level has become increasingly at odds with today's industrial practice in which both disciplines are not only complementary but also often intertwined. For instance, in gold ore processing, comminution, flotation, and gravity separation units are interfaced with atmospheric or pressure leaching modules and with carbon adsorption and electrowinning units. The new copper plants in South America combine comminution and flotation circuits with heap leaching, solvent extraction and electrowinning processes.In order to reflect this new industrial reality and to harmonise the options offered in both its engineering programs, the Department of Mining and Metallurgy of Laval University has introduced major changes in its curriculum in 1996. These changes reflect also the recognition that the somewhat secondary status given so far to Mineral Processing and to Extractive Metallurgy within their ""mother"" programs, Mining/Mineral Engineering and Materials metallurgical Engineering respectively, was in sharp contrast with their actual significance for the Canadian economy. Leading industrial voices have raised similar concerns and the Canadian Engineering Accreditation Board has also addressed this problem in its latest program evaluation.The changes implemented at Laval aimed at a) better representing MP and EM within the two undergraduate programs; b) training top-level versatile and multidisciplinary engineers, fluent in all aspects of MP and EM, irrespectively of which of the two ((mother)) programs they had chosen and capable of meeting today's industrial requirements; c) training students in process analysis, optimisation and automatic control using state-of-the-art software, and d) taking into account the co-operative nature of both undergraduate programs.Results are very encouraging in terms of student enrolment and industrial response. However, some concern is expressed on the sustainability of the renewed curriculum considering the drastic budget restrictions in effect at Laval as in most other Canadian universities."

Jan 1, 1999

By Mike Johnson, Niels Verbaan, David Dreisinger

The Search Minerals Foxtrot project in Labrador represents a significant Canadian resource of rare earth elements rich in the sought after heavy rare earth elements (19.8% HREE/TREE). A preliminary economic assessment of the project indicated that the project is technically feasible and economically attractive. A variety of metallurgical test programs have been undertaken which have led to significant streamlining and simplification of the process flowsheet. The improved flowsheet should allow Search to reach production earlier and will use conventional processing equipment. The results of these test programs are presented and discussed in this paper.

Jan 1, 2014

By Y. Nakamura, T. H. Okabe, S. A. Sunkar, K. Nose

Ruthenium (Ru) is known as a platinum group element with a very small production volume. In fact, the worldwide annual production of primary Ru metal is only about 20-30 tons, and it depends on the amount of Pt produced, since Ru is a byproduct from Pt smelting. The primary uses of Ru are as a material for resistors, as a catalyst for electrode materials, and as a sputtering target for hard disk memory storage. In order to recover Ru from the spent sand-blasting abrasive media generated during the cleaning of the apparatus used for Ru sputtering, a hydrometallurgical recovery process using hypochlorite solution has been investigated. In this study, various types of recycling processes that are presently under development are also introduced, and their features and differences are discussed. The advantages and disadvantages of the new recycling processes are evaluated, and the possibility of establishing new recycling processes in the future is discussed from a multilateral perspective.

Jan 1, 2014

By Zhibao Li, Kunming Zhai, Yan Zhang

The hydration kinetics of MgO, namely magnesia or magnesium oxide, obtained by calcination of magnesite MgCO3 or synthetic MgCO3·3H2O has been studied. Nesquehonite (MgCO3·3H2O) was prepared by the reaction of MgCl2 with Na2CO3 in a mixed-suspension mixed-product removal (MSMPR) crystallizer at 40 °C. Three magnesium oxide samples were obtained by calcination of magnesite MgCO3 or synthetic MgCO3·3H2O in muffle furnace at 900, 1100 and 1300 °C for 3 h, respectively. The hydration experiments of MgO samples were investigated at 25, 35 and 45 °C for 24 h in a stirred batch reactor. The hydration results indicate that the rate and extent of hydration of magnesia decreased remarkably with hydration temperature and increased with decreasing calcination temperature at a constant hydration temperature. The whole hydration reaction of magnesia was supposed to experience the promotive period and declining period. An empirical kinetic model ( k t p -?ln(1-??) ??) and a modification of the classical shrinking core model for diffusion control ( k t b d -?-?3 2 ????1 [1 (1 ??) ] ) have been applied to fit the experimental data of hydration in two stages, respectively. The values of kinetic parameters ( p k and d k ) were obtained by regression analysis and the activation energy of the sample at 900 °C was estimated to be 34.23 kJ/mol. The comparison between MgO from calcination of synthetic MgCO3·3H2O and a commercial MgO used in silicon steel production was carried out, indicating that special silicon steel grade MgO can be obtained by calcination of MgCO3·3H2O below 900 °C.

Jan 1, 2014

By R. L. J. Phillips

"The environmental impact of the Rabbit Lake project is presented. Baseline data for fish, water, air and radon collected in 1973, 1975, 1980and 1986, are compared with post-development environmental monitoring data. Predicted environmental impacts for the developed Rabbit Lake and B-zone deposits are compared to the actual impacts. INTRODUCTIONThe environmental impact of the Rabbit Lake project has been documented through the years in several submissions to the government agencies. In 1972, the environmental baseline study for the Rabbit Lake area was completed prior to any mining activity at the Rabbit Lake pit (Fig. 1).Sampling concentrated on Hidden Bay and Pow Bay, which received the treated effluent and the waters drained from Rabbit Lake respectively.A second baseline study was done on the Collins Bay area in 1980(Fig. I) in preparation for the mining of the B-zone pit. The detail in this study was considerably greater than the detail in the previous study. Collins Bay and Harrison Peninsula were the areas sampled. The B-zone deposit is being mined at present.With the discovery of the A-zone, D-zone and Eagle Point deposits, it was decided in 1986 to begin proceedings to obtain approval from Saskatchewan's Department of the Environment, and from the Atomic Energy Control Board to develop these deposits.In preparation, a third baseline study of both the Rabbit Lake and Collins Bay areas was done in 1986 and 1987. The emphasis was to establish the baseline at the three new deposits, to quantify the actual impacts of the existing Rabbit Lake operations and to confirm the Collins Bay B-zone (1980) impact predictions. The new deposits will allow us to continue to produce uranium into the future. In January 1988, Saskatchewan approval was received.Since 1975 in the Rabbit Lake area and 1980 in the Collins Bay area, routine environmental monitoring has been done. This has resulted in one of the largest and most comprehensive environmental data bases in North America in mining. By the time the Eagle Point deposit is mined to completion, there will have been data collected for approximately 40 years.Further discussions follow which describe the impacts of the past (1972 to 1984), the present (1985 to 1987) and the future. In addition, the past and present performances and the future plans of the .waste management systems will be discussed."

Jan 1, 1989

By R. R. Klimpel

"SYNOPSISA discussion of the importance of flotation rate in the analysis of mineral flotation is presented. In particular, the highly interactive nature of the flotation ""system"" is emphasized where there are components of chemistry, equipment, and operating conditions simultaneously involved. It is further shown that: 1) flotation rate must be measured in order to economically optimize the performance of an industrial flotation circuit, 2) that consistent patterns exist in both flotation rate and equilibrium recovery when changing various settings of the system components, 3) that knowledge of these patterns is necessary in order to avoid making system changes that are either self-compensating or dramatically re-enforcing in some particular aspect of performance, and 4) the rate related role of the chemistry component (e.g.frothers and collectors) is often much bigger than is sometimes realized (especially in a negative sense involving overdosing of reagents). INTRODUCTIONFroth flotation is widely usedl-6 in mineral beneficiation processes as a method for separating different types of finely divided solids present in a liquid (usually aqueous) suspension. The approach is based on the contacting of solids with upward moving air bubbles in an agitated vessel where the solids are exposed to chemicals (collectors) which create a condition favoring the attachment of a certain portion of the solids to the air bubbles. This selected portion is then removed in a froth stabilized by chemicals (frothers) and subsequently recovered from the flotation vessel. Depending on the settings of the various components of the flotation ""system"" (see Figure 1) it is possible to achieve a wide range of flotation performance."

Jan 1, 1984

By Amir Zavichi

Today, with the necessity of timely, on-budget and high quality completion of projects, proper use of construction equipment is essential to ensure project success. Construction equipment places a large monetary burden on the project and if not utilized efficiently, it can result in economic losses. Cranes are one of the most important and expensive operational devices on construction sites. They play a central role, and often activities that rely on crane services fall on the project?s critical path. Currently, material-handling scheduling is done by the crane operator or by an on-duty superintendent using his/hers personal judgment, making the process manual and timeconsuming. Thus, developing an optimal schedule, which considers different dynamic constraints in construction job site, may not be possible based on the current practice. This leads to longer operation times and a negative impact on project cost. This paper presents the latest results of an ongoing study, which aims to design and implement a nearreal time crane operation decision support system to be utilized directly by the crane operator or as an aid for the superintendent in scheduling optimal operation services. This system has several advantages such as maximizing the efficiency of crane operations, guaranteeing the best operation possible to reduce the crane?s travel time, reducing crews and equipment idle time, and minimizing the dependence on subjective human judgments.

Aug 1, 2013

By K Belanger, J. Mclachlan, F. Stober, G. Norval, B. Snider, A. Munsch, T. Koehler, E. Piantino, J. Carlos Queiroz

The project to rebuild the smelting furnaces at the Anglo American - Barro Alto ferronickel smelter, located in Goias, Brasil, was initiated in September 2013. To optimize the capital cost, while maximizing furnace integrity and robustness, a design basis giving flexibility to ore composition variation was developed in order to ensure sustained nameplate production. The resulting capital efficient, fasttracked project execution was accomplished through the creation of an integrated project team of Anglo American and Hatch through FEL 3 and FEL 4 phases of the project. The integrated team addressed the project challenges through a cooperative and versatile approach, created by access to knowledge, experience and systems in both Anglo American and Hatch. The team could operate at an optimized speed of execution, as demonstrated in the FEL 3 and FEL 4 completion durations, as well as efficiently mitigating any risks of increasing cost or delaying schedule by utilizing lessons learned and team knowledge from Anglo American on the original green-field project and Platinum smelters and Hatch on similar reference ferronickel furnace rebuilds. Other critical drivers of project cost minimization and revenue loss/generation (considering production revenue of each furnace) are scheduled durations for construction, commissioning and ramp-up. The integrated team commenced construction, commission and ramp-up planning almost one year in advance of the shutdown and this paper will discuss the strategies developed to reduce risks and optimize the construction schedule to mitigate revenue loss and optimize ramp-up time to sustained operation at nameplate capacity.

Jan 1, 2015

By C. M. Diaz, P. J. Mackey

Since its inception, in 1987, the Copper-Cobre series of conferences has established itself as the prime world forum for discussing advances in copper process metallurgy, in particular copper sulfide smelting, copper recovery by leaching and electrowinning and copper electrorefining. All copper producing countries have actively participated in the pyrometallurgy symposia held in the framework of these conferences. In 1999 and 2003, the close to 100 pyrometallurgy papers that were presented had to be accommodated in two volumes. In the present paper, the authors firstly provide a brief historical sketch of the Copper-Cobre conferences and then focus on providing a retrospective look at the dramatic changes that have taken place in copper smelting in the last few decades, primarily as discussed in the Copper-Cobre and precursor conferences pyrometallurgy proceedings. Topics include: the development of autogenous, increasingly more intensive, environmentally sound and energy efficient smelting processes; significant improvements in Peirce-Smith converting practice and at the same time the commercialization of alternative continuous converting routes; the consequent expansion and modernization of smelters; the increasing compliance with strict government environmental regulations in most copper producing regions of the world; the realignment of the copper smelting industry throughout the world; and trends in copper smelting R&D. A look at the future closes these reflections on the contribution of the Copper-Cobre conferences to the advancement of copper smelting technology.

Jan 1, 2007

By L. M. Lowe, D. G. Feasby, J. R. Goode

"Rare earth resources usually contain minor amounts of radioactive elements. The most widely recognised sources of radioactivity are associated with thorium and uranium. However, also present in the resources are isotopes of rare earth elements (REE) that are themselves radioactive, including lanthanum (La-138), lutetium (Lu-176) and samarium (Sm-147). These radioisotopes, as well as remnants of the natural thorium (Th-232) and uranium (U-238, U-235) decay series, can contribute to significant levels of radioactivity in mixed REE concentrates and in separated products. Levels such as these can present challenges for transport, transboundary movement, product storage, workers’ health and safety, as well as waste management issues at the facilities that separate out the individual REE’s. These are discussed in this paper. A particularly challenging radioactive isotope is Ac-227 (a decay product in the U-235 decay series). Actinium behaves chemically similar to lanthanides and hence normally concentrates with REE multi-element composites. Reliable analysis of Ac-227 is not widely available and the methodology required to deal with this challenge is briefly described. A principle reason for minimization of radioactive content throughout REE processing is restrictive specifications by concentrate purchasers in order to reduce waste management challenges. Approaches to the minimization of radioisotope content in REE concentrates and separated products are outlined in this paper."

Jan 1, 2014