Search Documents

By Werner Unland, Nick Holl

"The paper presents the engineering design and experience gained so far with a dewatering system for an open-pit uranium mine planned at Key Lake in Northern Saskatchewan.The results of hydrogeological investigations preceding engineering exhibit an extensive unconfined overburden aquifer hydraulically connected with the underlying Athabasca Formation and basement rocks, both of relatively low hydraulic conductivity. The overburden aquifer is embedded in a bedrock trough, with the deepest depression between the planned pits. The hydrogeological data were used in a numerical dewatering model simulating groundwater flow atdifferent stages of the pit development.Based on the model results, the engineering design had to provide for different pumping rates, varying between 1.0 and 0.21 ms/sec. This problem was solved by using a double line pressure system. The design concept for the complete peripheral discharge system and the well design used for 26dewatering wells are discussed.Experience with reverse-circulation techniques applied for the construction of the dewatering wells is presented. Theoretical and practical considerations which led to the constructionof wells of different diameters are discussed.The design of the in-pit dewatering system provides for seepage ditches, horizontal drains, pit-bottom sumps and inpit dewatering wells where required."

Jan 1, 1980

By Rita Michael

"The Marmara Ironworks was not the earliest ironworks in Ontario, but it was distinguished from other early works in a number of ways. It was established on an ambitious scale as a self-sufficient and, for the time, sophisticated community. In effect it was an iron plantation on the scale and scope of those at Hopewell, Pennsylvania and Saugus, Massachusetts(1). It was, besides, the only one of the few early ironworks in Upper Canada which operated almost to the end of the nineteenth century, albeit in fits and starts, and which used magnetic ores rather than bog iron ores (limonite). Furthermore it is the only works which has produced archaeological interest over a number of years. The ironworks is on the east bank of the Crowe River near Highway 7, on Lots 7 and 8, Concession 4, Marmara Township, Hastings County, Ontario. It is the property of the Village of Marmara, and the extant remains encompass about 2. 5 acres of the original 2000 or so which made up the original grant. The mineral riches of the Canadian Shield had been known since the days of the Jesuit missionary-explorers. A consortium headed by Alexander Henry and the Duke of Gloucester planned to exploit the copper near Sault Ste. Marie during the last part of the eighteenth century, but nothing came of the venture(2). This attempt may have grown out of Lord Dorchester's suggestion that private enterprise be encouraged in order that the iron ore which ""abounds"" in Canada might be exploited(3). John Graves Simcoe, the first Lieutenant Governor of Upper Canada was also anxious to see iron working develop. Simcoe was eager to encourage many enterprises, among which ""the development of iron mines""(4) - Governor Gore had been approached by John Mason for help with his ironworks in Norfolk County (5). Three Americans had applied for permission and support to erect an ironworks on the Gananoque River at the falls to become known as Furnace Falls. They were granted 1000 acres of land in fee simple to encourage their endeavor(6). Sir Peregrine Maitland, only a few months after taking up his duties as Lieutenant Governor in 1818, intended to visit the ""bed of iron ore on the Crow River"" (7) - Maitland was to provide a good deal of support, both moral and substantive, to Charles Hayes when he came to Canada in 1820."

Jan 1, 1999

By A. A. Holland

Introduction The world's largest known deposits of natural sodium sulphate (Glauber salt), generally termed 'alkali ' throughout western Canada, are located in the Province of Saskatchewan: reserves are estimated to exceed 200,000,000 tons. These are surface deposits resulting from the recent or present-day natural evaporation of brines, in which respect they are similar to those occurring in certain other parts of the world, as in semi-arid sections of the United States, Russia, Germany and Austria. In some areas, underground deposits formed hundreds of thousands of years ago have been _encountered in drilling, and indications are that they also were formed under arid or semi-arid conditions. The master key to the formation of deposits of natural sodium sulphate, wherever they occur, is a climate, either past or present, under which evaporation exceeds precipitation over a considerable period of time. Commercial development of the Saskatchewan deposits began about thirty years ago. Previously, the demand for sodium sulphate had largely been met by salt cake produced as a by-product in the manufacture of hydrochloric acid from common salt. The rapid increase in the production of Kraft paper and, more recently, the development of synthetic detergent materials, have caused a marked increase in the market for sodium sulphate. This chemical gives the extra toughness to Kraft paper and is used in detergent compositions in proportions as high as 75 per cent. Saskatchewan now has six commercial plants producing natural sodium sulphate. Production from each in the fiscal years 1947 and 1948 is shown in Table I. The newest and latest plant is that of Saskatchewan Minerals, at Chaplin, which 1s designed to produce up to 150,000 tons of salt cake, 98.5 to 99.5 per cent pure, yearly. This is equivalent to about 24 percent of the total United States production of crude commercial salt cake for 1947.

Jan 1, 1949

By Penny C. Stewart

Narrow vein underground stope design engineers in Australia have expressed significant interest in the requirements and methodology for developing site-specific stability charts. This is largely due to a concern that existing stope stability charts inadequately take into account factors influencing narrow vein stope stability, such as the effect of backfill abutments and the effect of in stope pillars. This paper presents conclusions from a comprehensive statistical examination of case history requirements for a site specific stability chart and critiques literature arguments for site-specific charts. A new statistical analysis technique and a large comprehensive stability database enabled the authors to quantify case history requirements and any site-specific effects the model exhibits. The analyses indicated that a reliable stable-failure boundary requires at least 150 case histories, of which a minimum of 10 percent should be unstable stope surfaces. Marginal site-specific effects were observed for the operating conditions captured within the database. The authors conclude that the apparent site-specific effects noted in previous literature are attributable to operating conditions inadequately represented in the database. Such operating conditions could induce erroneous stability predictions at any site, and are therefore not truly site-specific. Following from these conclusions, a strategy for taking into account operating conditions particularly relevant to narrow vein mining has been proposed. In particular, the development of a chart that accounts for the effect of backfill abutments on stope stability. Backfill abutment effects are particularly relevant to mechanised narrow vein mining methods such as modified Avoca. Collaboration from at least five sites is required to obtain access to relevant data and underground drives for geotechnical mapping. Preliminary estimations indicate that approximately three months fieldwork is required to meet case history requirements. CMS data in conjunction with 3-dimensional design software will be used to calculate equivalent linear overbreak/slough (ELOS). In contrast to stable, failure, major failure and caving categorical variables, ELOS is an objective and continuous stability variable and is therefore, more conducive to mathematical modelling.

Oct 1, 2001

By B. Surender Mohan

Mining lignite pollutes the environment and causes ecological damage if unattended. Being conscious of the importance of environmental resources for the well-being of the living system, the Neyveli Lignite Corporation (NLC) adopts the policy of environmental regeneration as the foundation on which productivity is built. NLC started investing on Eco Care and Environment Protection long ago and it continues. Early investment in environmental protection has resulted in steady growth of the Company along with a healthy environment. The future vision of NLC is to be in the vanguard among the contributors to the community, environment and the nation by developing and utilizing industrial and human resources to the optimum. Untiring efforts are being put in mines (NLC as a whole) to maintain and sustain the ecological balance arising due to continuous mining activity. NLC?s Environmental Management System is becoming a symbolic role model for many of the opencast mines in Southeast Asia. NLC has been bestowed with number of prestigious Environment and Sustainability awards in recognition of the mammoth contribution in maintaining a clean and green environment.

Aug 1, 2013

"The Cordillera contains numerous porphyry deposits and prospects, many containing economic quantities of copper, molybdenum, gold and tungsten. Over the lost twenty years, different phases of exploration have been driven by individual commodity prices and new discoveries. Exploration methods have remained largely unchanged since the 1960s and 1970s with the range of techniques chosen for each situation depending on the stage of the program, the type of porphyry target and the local environment. Improvements or changes to techniques have resulted from awareness of specific features in new deposits or regional problems. During the last ten years much of the emphasis has been on the re-evaluation of known porphyry deposits with more exploration in areas previously recognized as prospective. Re-evaluation of known deposits has resulted in increased reserves, often with improved gold grade, and the discovery of new zones. Several new deposits have been discovered including gold-only deposits of probable porphyry affinity.Research related to porphyry deposits has followed trends in exploration and has been directed toward the type of deposits that have been of current interest. In addition to research on specific deposits and areas, general research related to porphyry deposits has addressed three broad themes. The first theme involves the role of tectonic processes and the nature of source regions. Although different in detail, recent tectonic models suggest that a tectonic change or hiatus may be important for the generation of metal-rich magmas from various source regions and subsequent fractionation that permits volatile saturation. The second theme is based on magmatic processes, particularly the generation of a volatile phase enriched in metals. This research supports the general orthomagmatic model for porphyry deposits and has helped to define the influence of specific variables in the generation of different types of porphyry deposits. Finally, research on alteration and mineralization has provided evidence for different types of fluids and fluid processes involved in the formation of porphyry deposits. These data also support the orthomagmatic model but indicate additional complexity in magmatic-hydrothermal systems including the role of external fluids. Although important advances have been made, research has had a limited impact on exploration.Exploration and research on deposits that occur in the peripheral and upper parts of porphyry systems have been important over the last ten years. Although considerable advances have been made, the relationship of different styles of peripheral mineralization to magmatic processes in the core of the system remains ambiguous. An improved understanding of the processes that generate zoning, peripheral mineralization, and the surrounding alteration envelopes would be beneficial to exploration."

Jan 1, 1995

By D. C. Carter

"The Nova Scotia Department of Mines and Energy located a drillhole at Riverside Corner, Hants County, Nova Scotia, to examine the stratigraphy, structure and potash potential of the Kennetcook River gravity low. This evaporite-related gravity anomaly is one of the largest virtually unexplored gravity anomalies in Nova Scotia. The drillhole intersected a structurally complex sequence o flower Windsor Group ('B' Subzone) evaporites. Downhole geophysical wireline logs were used, in conjunction with detailed lithological descriptions, to interpret the structure and stratigraphy of the sequence. Similar application of total gamma ray, density, caliper and neutron-neutron log responses allows stratigraphic correlation of Windsor Group carbonate marker units separated by up to 35 km in Cape Breton. This work confirms the value of downhole geophysical logs as a tool in the exploration of evaporite deposits regardless of the presence or absence of high quality core. INTRODUCTIONThe exploration methodology for evaporite (specifically salt/potash) deposits in eastern Canada (and worldwide) is relatively simple: identify a negative gravity anomaly within a favourable geological setting, Windsor/Cordroy Group sediments in eastern Canada, and drill it (Anderle, 1980). Although this is an obvious oversimplification of the necessary expertise in the planning and complet ion of an exploration program, those familiar with potash exploration drilling can attest to the risks and expense, in terms of time and problems , associated with the location and drilling of diamond-drill wildcat holes. Potash exploration programs in eastern Canada, their results and inherent difficulties, have been documented by Anderle et al. (1979), Cooper (1981), Dekker (1982), Carter and Boehner (1986), Carter (1988) and Carter and Anderle (in prep .).Downhole geophysical wireline logs have become an important tool in the stratigraphic and structural interpretation of evaporite sequences in eastern Canada and, in many cases, represent the only information recovered or the only information available due to the drilling method (rotary) and/or the long term instability of evaporite cores. This paper documents examples of downhole geophysical log responses which, combined with detailed lithological examination of drill core, or in the absence of core, are used in the interpretation of the complex lithology and structure of a deformed evaporite deposit. Geological and geophysical data from the Nova Scotia Department of Mines and Energy (NSDME) Riverside Corner 85-1 drillhole are presented here as a partial case history and prime example of the use of this method to interpret the complex structure of an evaporite deposit. Drilling of NSDME Riverside Comer 85-1 was conducted in late 1985and early 1986by the Department (Carter and Boehner, 1986) under a program to assess the potash potential of selected areas of the province as part of the Canada-Nova Scotia Mineral Development Agreement 1985-89. A reinterpretation of a portion of the available data from two exploration drilling projects on Cape Breton Island in the Canso-Bras d'Or area is also presented (see inset, Fig. I). Several drillholes have intersected the Windsor Group evaporite sequence in these areas and the available geophysical logs are a valuable tool in the interpretation of the structure of the deposits. However, no attempt has been made to present or discuss the detailed geological investigation and comparison of these two deposits. They are presented here as an example of the reinterpretation of existing data and their application to stratigraphic correlation and structural interpretation of complex evaporite deposits. Further work is necessary to document the stratigraphic and structural correlation of these two areas."

Jan 1, 1989

By D. W. Zandee

"IntroductionHaving mined an economic mineral bearing rock which is of insufficient grade to warrant direct smelting, upgrading or beneficiation is required to make it an economically viable ore. The first step in effecting the concentration process is comminution or sequential breaking of the rock to allow liberation and subsequent recovery of the desired mineral particles. Desirably the ore could be broken down to the point where the valuable mineral is completely liberated to maximize the chance of recovering as much of it and in as pure a form as possible. The number of energy intensive stages of breakage required to attain this goal depends on many physical characteristics of the ore such as hardness, friability, toughness, grain size, existing fracture planes and particle shapes.Commonly the distinct stages are primary, secondary and often tertiary crushing and finally grinding. To increase the efficiency of each stage of size reduction, pre-treatment sizing is common.Crusher feed is commonly scalped of large pieces or screened for reduction crushers and classified for secondary grindingcircuits.Although crushing and screening is employed for many different products, this chapter reviews current practice in larger tonnage metalliferous ore treatment plants.Current practice is to use large gyratory or jaw crushers for primary crushing and some sort of gyrating or cone crushers for additional stages of reduction. For autogenous or semiautogenous grinding circuits only the primary crushing stage is necessary, the balance of the work being performed in the grinding stage. For conventional grinding circuits using ball mills or combinations of rod and ball mills, secondary, tertiary and even quaternary crushing stages are normally required.Older type crushers such as stamp mills, double rolls, sledging mills and hammermills are no longer common but are used for small tonnage special processes.Important to efficient crushing are a variety of sizing devices such as grizzlies and vibrating screens. Products at different stages must be stored to give surge capacity and allow controlled feeding rates through mechanical and gravity feeders. These storage piles, bins and feeders as well as crushers and screens are commonly integrated into a total facility by means of conveyor systems. Most often these are endless rubber belts driven by simple or multiple drive mechanisms usually consisting of electric motors and speed reducers."

Jan 1, 1989

By T. B. Williams

A SEARCH of the records indicates that evidences of accumulations of petroleum and natural gas within the boundaries of British Columbia were discovered at approximately the same time as were those of Alberta. They probably would have been developed as soon bad it not been for the fact that they are in such uninhabited parts of the Province. Even today, the seeps of the Flathead area, and the later discovered extensive seeps of the Peace River area, have been seen by very few people. From the geological evidence, there is reason for believing that British Columbia soon will be a petroleum producing Province. Fifty-eight operators, both companies and individuals, are now backing the money and the effort which they have invested with us, for the most part within the last three years, in a belief that this is so. The promulgation of the Petroleum and Natural Gas Act in 1947 marked the beginning of a new phase with regard to the exploration and the development of our petroleum and natural gas resources. Since August 15th, 1947, the date on which the Act came into force, the area under exploration bas increased from a few thousand acres, held by lease under the Goal and Petroleum Act, 1986, to 10,460,115 acres, including all active permits, licences, and leases. In addition there are 192,720 acres under application, bringing the total under issue and application to 10,652,835 acres. The total area is comprised of 105 permits, 20 licences, and 26 leases under the 1986 Act. The permits and licences, which ?represent active exploration and development, are held by a total of 82 companies and 26 individuals.

Jan 1, 1951

By Robert B. Parsons

"New tax rules that can apply to the repayment, extinguishment, or other settlement of a company's debt are finally taking shape. These new rules are far-reaching in their application, and can affect mining companies in a serious, negative way.IntroductionIn his February 1994 budget, Finance Minister Paul Martin announced changes to the Income Tax Act that could have an adverse impact on a company that restructures its debt. Since then, the new rules have undergone considerable transformation during their fetal stage: draft legislation was introduced in July 1994; revised draft legislation was introduced December 1994; and a third version of draft legislation was introduced February 1995. It seems that the new rules have now been pretty well finalized, and they contain some serious traps that the unwary could fall into. The new rules are of particular importance to mining companies, because a mining company's resource pools will be caught under the new rules, whereas these pools escaped the wrath of the old rules. The following commentary summarizes the new rules that are generally referred to as the ""debt forgiveness"" rules."

Jan 1, 1995

By Junior Santos

Kinross Paracatu started the operation of the new gold processing plant in the end of 2008, being composed by one SAG mill and two ball mills. During the first year of operation the plant had several problems related to stability and throughput capacity, mainly due to low grinding efficiency of the ball mills. In this period many actions were taken to maximize the throughput rate. Among the actions are reducing the size of balls in the mills, increasing the ball charge in the SAG mill, changing cyclone configuration and return of circulating load to SAG mill. With better stability of the circuit, the second stage of improvements has begun with the objective of increasing throughput rate and also reducing operation costs. Among the actions are the optimization of ball charge in the mills and a better operational control of cyclone parts. After two years of operation was obtained a significant increase in plant capacity, but still requires the addition of a third ball mill in order to maximize the use of SAG mill, which has spare capacity.

Jan 1, 2012

By Moe Momayez

Shotcrete is a practical and economical support system in many Canadian underground mines. Although shotcrete technology has gained acceptance in the mining industry, there are some problems that have emerged with respect to quality assessment and thickness measurement of the liner. This paper presents recent tests performed with a miniature seismic reflection device developed primarily for thickness measurement of this heterogeneous liner. Work was performed on site in an underground mine in Ontario, Canada. This paper also presents the results from laboratory tests performed on fibre reinforced and non-reinforced shotcrete panels that were used to assess the P-wave velocity in both materials. The results of these tests were used in a second on site investigation. The NDT thickness measurements showed good agreement with direct thickness measurement such as coring.

May 1, 2001

Eagle Plains Resources? Exploration in the Northern Cordillera ?Eagle Plains Resources Ltd. (EPL) is actively exploring for Zn-Pb deposits in the northern Cordillera in both carbonate-hosted and shale-hosted (sedex) environments. ?This presentation will review some of the significant carbonate-hosted Zn-Pb showings occurring in the Mackenzie Mountains, NWT and make limited comparisons with sedexdeposits in the adjacent Selwyn Basin.

May 1, 2006

By L. Dubourg, H. Habibi, D. Rasmussen

The combination of laser welding with Gas Metal Arc Welding (GMA W) forms the hybrid laser-OMA W welding. This process is an attractive tool with a high potential in welding lightweight structures, especially for aluminum alloys. For five years, this technology has increasingly attracted interest in both, industry (aeronautics, automobile, metal industries producing large structures) and academia (universities and research centers). Hybrid laser-OMA W welding process is generally accepted for its robustness, efficiency and flexibility. Coupling of a deep-penetrating laser beam with the heat and molten metal feeding of GMA W significantly expands the original welding application range of lasers. Its main advantages compared to the two individual components are deep and stable weld penetration, gap-bridging ability improvement, low distortion and easy filler metal addition. Hybrid welding allows a much wider groove tolerance compared to laser welding, especially for aluminum welding. Moreover, the reduction in distortion decreases the post-welding rectification needed and makes the assembly easier. In addition, if metallurgical factors are critical, the weld composition can be balanced with filler metal, decreasing the hot cracking susceptibility of some aluminum alloys. The combination of these two welding processes can also improve the weld bead shape quality (including the elimination of undercut), possibly reduce the porosity and increase the welding speed. This article reviews the recent works about the laser-OMA W hybrid welding of aluminum alloys. After a brief presentation on the interaction mechanisms between a laser beam and an electric arc, the paper depicts the typical welding parameters and experimental methods along with their characteristics.

Jan 1, 2006

"The success or failure of coal mining operations in Western Canada may hinge on the ability to extract thick coal under a variety of geological and mining circumstances and conditions. The paper presents, in who-where, what- how pattern, the current status of undergrounud mining of thick coal seams based on a review of foreign technical literature. The underground production of coal from what are considered to be thick seams is over 300 million tons per year. Methods of mining have evolved, through years of trials and tribulations, capable of meeting the requirements of a modern mine: high bulk outputs from a limited number of mining faces by concentrating in the horizontal (mechanization) and in the vertical (increased working lift)."

Jan 1, 1972

By P. T. Bloomer

Introduction Mining of the orebody of the Sullivan mine, which is owned and operated by the Consolidated Mining & Smelting Company of Canada, Limited, has reached a point where pillar extraction is rapidly becoming a major part of the operation. Very few of the larger pillars have been completely extracted; consequently, this paper contains much that is theory and expectation. Due to early mining methods and the physical characteristics of the Sullivan deposit, similar conditions may not exist in other older mines facing the problems of pillar extraction, but it is thought that the methods employed and those contemplated may be of general interest. History The Sullivan orebody, which is at Kimberley in the Fort Steele mining division of the East Kootenay district of British Columbia, was discovered in May, 1892, by Messrs. Sullivan, Smith, Cleaver, and Burchett. After passing through the hands of several owners the property was optioned in 1909, and purchased in 1910, by The Consolidated Mining and Smelting Company of Canada, Limited. Early mining was highly selective, the objective being a clean, high-grade silver-lead ore. By 1923 the difficulties of milling the very complex ore had been overcome and the first unit of a concentrator was completed with a capacity of 2,500 tons daily. Capacity was increased by stages to the present rate of 8,500 tons per day. Concentrates are shipped over the Canadian Pacific railway ? to the Company smelter at Tadanac, British Columbia, for final treatment. Approximately 45,000,000 tons of ore has been mined to date.

Jan 1, 1948

By Himanshu Dehra

The pre-fabricated outdoor rooms are often utilised near the mines and construction sites for office purposes. The paper has presented modelling and simulation results of the integration of commercially available glass coated photovoltaic (PV) energy technology and solar ventilation technology into a pre-fabricated outdoor room. The pre-fabricated outdoor room has been setup at Concordia University, Montréal for full scale testing of the glass coated PV modules with solar air ventilation. The computer simulation model has been developed for PV modules installed on a double wall wooden frame in an outdoor room based on its preliminary field testing. The testing apparatus was a wooden frame assembly of double wall with solar air ventilation: two adjacent glass coated PV modules, air column and plywood board filled with polystyrene. The measurement data collected from various sensors were: solar intensity, ambient air temperature, room air temperature, electric power, surface temperatures of PV modules and plywood board, air velocities and air temperatures in the air column. The enhancement in the air velocity of the air column was achieved with an exhaust fan fixed in an outdoor room. The simulation model is used to perform the two dimensional energy analyses with applied one dimensional solution of steady state heat conduction equations. The simulation model is based on conjugate heat exchange paths with network boundary conditions of convection, radiation heat exchange and solar air ventilation heat transport. The model parameters are based on measured values of ambient air temperature, room air temperature, air velocity at outlet of air column in double wall, electric power and available solar intensity. The model has predicted fairly well energy performance of glass coated PV modules with solar air ventilation installed on a wooden frame. The model is also useful for predicting heating, ventilating and air-conditioning (HVAC) requirements for the pre-fabricated outdoor rooms.

May 1, 2007

By W R. Honeywell

Two series of laboratory flotation tests were carried out to study the treatment of Faraday ore by two-stage flotation. First the acid-consumers and then the uranium minerals were floated. On ore ground in the Faraday mill grinding circuit, and using Faraday mill water in the flotation step, a recovery in the flotation concentrate of from 91 to 93 percent of the uranium was obtained in 45 to 50 per cent of the weight at a grade of 0.24 per cent U30s. The saving of acid in leaching the uranium-bearing flotation concentrate, as compared to leaching the whole ore, ranged from 30 to 46 per cent. The average over-all extraction resulting from flotation and leaching of the flotation concentrate was 88.1 per cent. The best collector for the acid-consumers was sodium oleate. Acintol F A-1 emulsion was the best collector for the uranium minerals, and, in the uranium flotation step, an acid pH in the slurry was found to be necessary. The reagent costs were estimated to be 22 to 26 cents per ton of ore.

Jan 1, 1963

By I. Haskett

ABSTRACT The Redwater pool, in north-central Alberta, was discovered in October, 1948, and at the end of 1950 was about 85 per cent developed. Production is from a Devonian coral limestone reef and is found at an average depth of 3,150 feet. The pool has an estimated .productive area of 37,000 acres, and a maximum oil zone thickness of slightly over 200 feet. Wide variations exist in both type and values of porosity, with the average value determined for the reservoir being 6.16 per cent. The total stock tank oil in place is about 1.24 billion barrels. The crude has a saturation pressure of 485 psig, com-pared to the original value of 1,050 psig for the reservoir, and the principal recovery mechanism so far has been the natural water drive. Cumulative production to January 1st, 1951, has been about 15.5 million barrels. These withdrawals resulted in a reservoir pressure decline of slightly over 100 psi. Predictions of future behaviour indicate that the water drive will not be of sufficient magnitude to maintain the reservoir above saturation pressure past 1953, and that, with natural depletion, the pool will be produced largely by a solution gas drive. Pressure maintenance by water injection has been considered and the possibility of raising the pressure to the original value of 1,050 psig is also discussed. INTRODUCTION WITH the discovery of the Lewduc pool, early in 1947, the Devonian limestone became the major geological formation contributing to Western Canada's rapidly growing petroleum reserves. Redwater, discovered in October, 1948, is now the largest known Devonian pool in Canada, with a recoverable reserve estimated at approximately 500 million barrels. Until recent years, the knowledge of the nature and characteristics of this type of limestone reservoir has been comparatively limited.

Jan 1, 1951

By The Staff

FOR forty years cyanide men have been intensively engaged on the treatment of sulpho-telluride ores. So far as we know, the processes used today were-with the important exception of the concentration plus high-lime process at the Victor mill (1915)-in use, or had been tried, in the earl y years of the century. Roasting, bromocyanide, ordinary cyanide, table and vanner concentration, floating and treating the concentrate, roasting con-centrates prior to treatment, etc., all were used at Kalgoorlie in 1904 or earlier. Flotation, followed by shipment of the concentrate to the Golden Cycle mill, was the practice at the Vindicator mine, Cripple Creek, for some years prior to 1917. Similar practice was employed in the Portland Independence mill at Victor, Colorado, and was lacer superseded by the table concentration, high-lime cyanide treatment of rails of the older Portland Victor mill. During all this time, an immense amount of research was being clone on these ores by the staffs of numberless companies. Conclusions were drawn and mills built. But if the results of one per cent of this research were ever published in sufficient detail for intelligent use by others, the Lake Shore staff has been unable to discover them, or does not recall having clone so. Government laboratories-as for instance chose of the Mines Branch, Ottawa, in or about 1927-have touched upon certain methods in their publications, but they simply have not had the time to finish the job. The paper by W. E. Johnston, Tellurides-Problem or Alibi? (E. & M.]., Aug., 1933), aroused wide interest and comment. It published conclusions, some right and some wrong, and gave the evidence adduced by the author i:n support thereof. Conclusions published without supporting evidence are to most of us worse than no conclusions at all. We suggest chat, if even one-tenth of the operators had published full, detailed results of their laboratory work, ad vance in the treatment of sulpho-telluride ores would have been very much accelerated. Therefore, we venture to inflict upon the Institute a compendium of the results of laboratory work performed during the past few years at the Lake Shore mill. It is really a summary of the more interesting results to date, prepared by the mill staff for their own use and benefit. But we hope chat the discussion under any heading is so detailed chat it will be intelligible to anyone interested in that phase of the subject.

Jan 1, 1936