Search Documents

By Lownds C. M

Several classes of commercial explosives and blasting agents behave non-ideally, especially in diameters near their critical diameter. A direct and convenient measure of non-ideal behavior is the detonation velocity (VOD); if the VOD is less than the ideal value, usually obtained by calculation, then the explosive is detonating in the non-ideal mode. Such lowering of the VOD is usually due to both lateral loss of energy and post-CJ release of energy. The second of these factors, namely slow release of chemical energy, is of most interest in blasting. While the observation of a low VOD clearly suggests slow reaction of part of the explosive composition, it does not necessarily mean that the energy is lost to the overall rock-breaking process. The partition of the energy of the explosive into various useful and wasteful categories is considered. Simple models of energy partition in blasting, and of explosive reaction kinetics, are presented. The models consider the effect of explosive type and rock type, the explosive being described in terms of the most common phases namely liquid, air bubbles, porous ammonium nitrate, dense or crystalline ammonium nitrate, and aluminum. Over a range of combinations of the above phases, the model predicts reasonable critical diameters and VOD's. Results are presented which show the effects of non-ideal detonation on fragmentation and heave in different rock types. Conclusions are drawn about those blasting conditions in which ideal behavior is beneficial, or Disadvantageous.

Jan 1, 1990

By Houlihan RN, Landau J

A reciprocating plate column is described in which two sets of perforated plates are mounted alternately on two shafts and are reciprocated with a phase difference of 1800 between them. It is shown that such a column is mechanically superior to the previously proposed types: under practical operating conditions the pressure fluctuations at the base of the column are only a small fraction of the static head. Furthermore, mass transfer experiments with the system tributyl phosphate in kerosene- acid aqueous solutions of uranyl nitrate show that both high specific throughputs and reason- ably good efficiencies can be attained in this type of column. A comparison with the more conventional extraction equipment (mixer -settlers, pulsed columns) on the basis of residence time per equilibrium stage indicates the potential of reciprocating plate columns in hydrometallurg- ical application, especially in which the requirements of separation efficiency are modest while the scale of operation is large.

Jan 1, 1975

By Segnit R. E

Two suites of dusts (waste-heat boiler and electrostatic precipitator) collected in 1976 and 1980 from the Kalgoorlie nickel smelter were subjected to chemical and XRD analysis and were examined by SEM and optical microscopy. The spherical to sub-spherical particles contained oxide and glassy phases with small amounts of sulfide. XRD showed that the major phase was a mixed Ni-Fe oxide spinel with some hematite. These phases compared well with those predicted by thermodynamics. The particle size distributions showed that in the 1976 and 1980 suites 20 per cent by weight was respectively coarser than 60 and 115/lm (boiler dusts) and 40 and 30/lm (precipitator dusts). Maximum particle sizes estimated from sedimentation chamber theory were found to be in reasonable agreement with the maximum sizes found in the dusts.

Jan 1, 1984

There has been considerable attention in the literature to coarse sizing by wet and dry screening, but these methods have not proven to be applicable to the calculation of screen capacities for fine wet sizing, desliming and media recovery: A method is presented for the calculation of the size of screens for such duties, being based on the mean particle size of the oversize material on the screen which reflects the surface area from which the fines or media must be removed. Similarly for dewatering, it is the area from which the water must be drained. Desliming, media recovery and dewatering are each considered along with water require- ments both with the feed and as wash water.

Jan 1, 1984

Roadheader tunnelling machines have been used in Australia by both mining companies and contractors involved in the mining and con- struction industries since the early 1970's. They have both advantages and limitations, and this paper discusses machine excavation from the point of view of a contractor who has both reaped the benefits and suffered the conse- quences of using roadheaders. The paper also includes brief descriptions of three projects tackled by roadheader, all the projects being Declines.

Jan 1, 1987

The safety of mine winder systems with regard to overwind, underwind, rope factors of safety, winder brakes and the like is discussed. Many misunderstandings and poten- tially unsafe practices are discussed as well as variations between requirements of various Mines Departments. Various methods to improve safety are suggested and the formation of an industry committee to review present practice and foster development of improved safety and economy is also suggested.

Jan 1, 1984

With production at Olympic Dam scheduled to commence in June 1988, it has been necessary to install a complete underground ore handling system capable of removing two million tonnes of material annually from the mine. The system comprises mucking from stope drawpoints, truck haulage to underground storage, primary crushing, conveying and hoisting. On the surface, material is conveyed to stockpiles at the Metallurgical Plant. Mining of the numerous special excavations within the system was incorporated into the mine's ongoing development program prior to the underground construction phase. Utilisation of a decline from the surface enabled versatile construction equipment to operate at the underground sites as well as simplifying the transportation and delivery of construction Materials.

Jan 1, 1988

By W Whiten

The determination of mineral composition is necessary in the mineral sands industry. Tiwest has developed a procedure for safe and convenient determination of the mineral composition using a magnetic separation followed by chemical analysis using X-ray fluorescence spectroscopy. This then requires the conversion of the elemental assays to mineral compositions. A project at the Julius Kruttschnitt Mineral Research Centre has developed a convenient analysis method for this conversion. This analysis is based on a reconciliation of the of the assays of the sample with the standard mineral assays by making minimal adjustments based on the assay accuracies to both sets of assays. As well as providing the mineral composition it to be tested for other applications and variations of the procedure to be evaluated. Given a range of samples, testing for the accuracy of the assays of the standard minerals, has been demonstrated.

Jan 1, 2001

By S Latchireddi

Close circuiting autogenous and semi-autogenous mills is anenergy efficient way of grinding and a number of operations haveutilised this in the design of their comminution circuits. Owing tothe large flow of slurry through the mill that results fromoperating this way the grates and pulp lifters have to be designedto cope. However, the literature has little or no information onhow grate and pulp lifter size and design are related to theirability to remove slurry from the mill. Over the last few years theJKMRC has been researching this area and has developedrelationships between grate/pulp lifter design and flowratecapacity. At the same time it has determined the major causes ofpulp lifter inefficiency and a solution to preventing thisinefficiency (the Twin Chamber Pulp Lifter). This paperdescribes the models that have been developed through thisprogram and uses industrial scale data to illustrate their accuracy.Results from the industrial trials of the Twin Chamber PulpLifter are also presented.

Jan 1, 2001

By Sheng X. L

The Jurassic coals at Datong are characterised by their strong, massive sandstone and conglomerate roofs which fail suddenly over large areas, crushing pillars and creating destructive windblasts. collapsed areas have exceeded 180,000m2 and windblasts have extended over one km underground and 200m on the surface and have been accompanied by subsidence troughs on the surface. Scientific analysis has researched premonitory signs of caving and the nature of windblasts leading to considerations of alternative mining methods and ways of dissipating the energy of windblasts to reduce their damage and danger..

Jan 1, 1992

By Noakes MJ, Willsteed TV

In the past few years an elevated gold price has resulted in the evaluation of many small scale surface gold deposits in Australia typically containing about 2-3 g/t Au. Operators have tended to assume that at the lower end of the grade spectrum only heap leaching is economically possible whereas above some assumed "cut-off" grade, carbon-in-pulp or similar techniques can be considered to have economic advantages.Studies made on a number of these prospects has indicated that this rather arbitary choice of treatment method can be mis-leading.A case study has been prepared assuming a "typical" situation and is presented. The deposit contains three million tonnes of ore assaying 3 g/t Au and is amenable to open pit mining methods. The mine site is remote but accessable and existing infrastructure is minimal. There are no unusual environmental constraints.

Jan 1, 1984

Australia contains a variety of iron ores, differing in grade, chemistry, size distribution and genesis. While a proportion of this ore is used world-wide as blast furnace lump, much of the material mined is high grade fines, requiring agglomeration (usually sintering) before blast furnace reduction. Sintering studies initially concentrated on the production of ferrous material of high iron content, coarse size and sufficient cold strength. In recent years research involving pilot plant sintering, precise test procedures and mineralogical analyses has focussed on the additional sinter properties of hot strength and reducibility. Aspects of mineralogical studies applied to iron ore sintering are described.

Jan 1, 1989

By Moon N. T, Torrance A. C

This study has considered the effect of mechanical shock on the resilience of the glass microspheres commonly used to sensitize an explosive emulsion. The damage to the glass microspheres caused by detonating cord, emulsion manufacture and the manufacture of the glass microspheres were considered along with the effect of sensitizer concentration on explosive performance. Reductions of up to 50% in the glass microsphere concentration of an emulsion explosive can result from poor initiation practice, such as the use of high strength detonating cord as downlines during initiation. Laboratory results suggest that detonating cords of strength greater than 3.5 g/metre should not be used as this can seriously affect explosive performance, particularly in small diameter charges. This reduced performance results from damage to the sensitizer elements and recrystallization of part of the emulsion phase.

Jan 1, 1990

The number and severity of sulphide dust explosions in underground metalliferous mines have increased in recent years, despite various methods used to prevent or inhibit them. A dust explosion occurs when a cloud of combust- ible dust in an oxidizing atmosphere is exposed to an ignition source with sufficient energy to ignite the dust. A computer blast simulator model was used to investigate the movement of the fractured rock, temperatures and volumes of the explosion gases in a 70 m high, 24 m wide open stope.

Jan 1, 1988

By Clark GH

Batu Hijau is a porphyry copper-gold deposit located on Sumbawa Island in the western Banda Arc of Indonesia. The deposit has been evaluated from 54000m of drilling in 105 diamond drill holes over a surface area of 1.2km2 and to a depth of 1000m below surface (412m below sea level). A provisional plan is being evaluated to mine 642 million tonnes at an average grade of 0.61% Cu and 0.55g/t Au (variable cutoff) from an open pit in the higher grade portion of the resource. The deposit is associated with a caic-alkaline intrusive complex that was emplaced in a thick sequence of andesitic pyroclastic rocks. The oldest and most widespread intrusion is porphyritic to medium-grained, equigranular, quartz hornblende diorite. At Batu Hijau the western diorite contact zone was intruded by two phases of tonalite. The older tonalite is a stock increasing from 200m diameter at surface to 500m at sea level. It consists of quartz, plagioclase and hornblende phenocrysts set in a groundmass of similar composition. A younger tonalite intrudes the tonalite stock, quartz and plagioclase phenocrysts are more abundant and it has a finer groundmass than the older tonalite. Brecciation occurs near the older tonalite contacts but there are no breccia pipes or late-stage features such as pebbldykes or postmineralisation intrusive rocks.

Jan 1, 1995

Government geoscience may be categorised by objective under three headings: Applied Research for Geoscientific Framework Studies, Resource Inventory, and Technical Advice. In Queensland, the Department of Resource Industries is active in all three categories. Under the program-based management system adopted in 1987, three Programs, namely, Geological Survey, Mineral Resources Development, and Energy Resources Development and Utilisation, have geoscience responsibilities.Prime responsibility for geoscience resides with the Geological Survey Program, which provides a geoscientific framework for mineral and energy exploration and the development of the State. Simply stated, the Program goal is to provide geological information when and where it is required. Geological Survey work also encompasses aspects of resource inventory and technical advice, complementing the work of the other two Programs. This role has a 122 year long tradition, for geoscientists of the Geological Survey have been engaged in investigations designed to facilitate the identification and utilisation of the mineral, water and energy resources of Queensland since 1868.

Jan 1, 1990

By North R. A

The Queensland Mining Act 1968-1972 has now been in force for almost two years. The Act was completely re-written and has made for easier working, e.g., there is no distinction now between Gold Mining Leases and other Mining Leases. For the first time in the history of Queensland, provision has been made for caveats, so that options etc. can be protected. The chief problem which has arisen so far has been the question of the Government issuing mining leases to the holder of an Authority to Prospect over areas which are included iri its Authority. Litigation has taken place and an Appeal, it is understood, will shortly be heard by the Privy Council. The provisions dealing with labour conditions have been brought up-to-date and generally speaking, they are quite clear as to the responsibility of the Lessee. The Mining on Private Land Act has been repealed and the provisions relating to mining on private land are now a part of the Mining Act itself. Previously, the holder of a- mining freehold did not have to pay royalty on

Jan 1, 1974

By D E. Freeman, M A. Somerville, B M

A program of re-planting native mallee trees, which can be harvested on a short rotation cycle, has been initiated in Western Australia to counteract increasing soil salinity in the wheat belt region. Large volume applications for the wood products generated by these plantings are required to improve the returns to farmers. The metallurgical industry is a large-scale user of carbon, and a project was carried out through the Centre for Sustainable Resource Processing to investigate the use of mallee-derived carbons in metallurgical processes. The use of renewable carbon sources, such as charcoal, to replace fossil carbon has the additional benefit of reducing the net CO2 generated by the metallurgical industry. Experiments were undertaken to assess the performance of mallee derived charcoals as reductants for the solid state reduction of ilmenite and for iron ore bath smelting. Rotary drum reduction tests showed that the reduction rate of ilmenite with the mallee charcoal was approximately twice that of Collie coal at the same fixed carbon/ilmenite ratio in the bed. Iron bath and slag bath injection tests demonstrated that the mallee charcoals dissolved readily in molten iron carbon baths and reacted efficiently with iron making slags.

Jan 1, 2006

FIRST TOWN PLANNING PROPOSALS Initially, accommodation at the minesite was provided at the Pastoral Homestead situated some seven kilometres north-east of the mine and between 1963 and 1966 was the base of the exploration camp. Tents were used for sleeping of 100 men and the Homestead used for dining and office facilities. With the beginning of ore production and shipment due to commence in 1969 a permanent town location was sought. Early town planning studies had been commissioned by Amax Inc. and Colonial Sugar Refining Co. Ltd. and in 1967 The Broken Hill Proprietary Company Ltd. took over the responsibility for putting them into effect. The location chosen was about four kilometres due east of the mine. Certain dominant factors influenced this choice. It was near enough to the mine to share services, yet far enough away not to be affected by dust and noise and received the additional shelter of a range of hills separating it from the mine. A predominant slope to the east provided good drainage and the ground was easy to excavate for services.

Jan 1, 1976

The relationship between the permeability of coal to a mixture of methane and carbon dioxide, and the permeability to methane and carbon dioxide separately is described in this paper, along with the analysis of the differences in permeabilities of coal to methane and carbon dioxide.

Jan 1, 1989