Search Documents

By A M. Robertson, R Lefebvre

Air movement and associated oxygen transport through waste rock dumps has the potential to significantly enhance the rate of oxidation of pyrite-bearing material. While this is a desired outcome for most heap leach operations, airflow in waste rock storage facilities can result in significant increases in generation and acceleration of acid rock drainage. Hence, a good understanding of internal airflow through waste rock dumps is required to control ARD and minimise any associated liability. The principal mechanisms contributing to airflow and oxygen transport in a waste rock pile include: diffusion; advection due to a thermal gradient (chimney effect) and/or wind pressure gradients; and advection due to barometric pumping. While diffusion is typically limited to a near-surface zone of a few meters depth, advection and barometric pumping have the potential to move air (and oxygen) to much greater depths into the pile. In general, the more permeable the waste rock material, and the greater the height-to-width ratio of the waste rock pile, the greater is the potential for advective air movement. The reactivity of the waste rock material as well as the coarseness (hence air permeability), and the spatial variability of these properties within a pile, have a strong influence on the magnitude of thermally induced advection. In contrast, air movement due to barometric pumping is controlled by the waste rock porosity, changes in ambient air pressure and the heterogeneity of air permeability of the waste rock dump. Results of field monitoring and numerical modelling using TOUGH AMD are presented to illustrate the concepts on air movement in waste rock piles discussed in this paper. During the design and construction phase, airflow can be controlled by judicious placement of reactive waste rock and use of selective placement techniques to control the internal structure of the waste rock facility (eg introduction of horizontal layering, prevention of inclined, high-permeability, channels (æchimneysÆ)). Several closure measures are available to minimise airflow including: placement of a low-permeability cover to reduce air entry; and placement of a non-reactive cover material to isolate reactive material from the zone of active airflow and/or regrading of the waste rock pile to obtain a geometry and internal structure less susceptible to advective airflow.

Jan 1, 2003

Solar Salt, Lunar Ambitions I Bauerti The title of this paper is `Solar Salt, Lunar Ambitions'. It is largely the result of a lack of imagination and a tight deadline. I was seeking a catchy title to convey the image of being 'here' and wanting to get `there', with `there' being a long way away and our being held 'here' by powerful gravitational forces. I tried `Solar Salt, Lunar Landings', but that implied we had already reached `there' when, on reflection, we had not. A colleague suggested 'Solar Salt, Luna Park' which is a fun park in Sydney and, I must admit, there was appeal in the image of having embarked on a wild roller coaster ride with stomach-wrenching twists and turns and the only reward being a pair of sweaty palms, and a feeling of nausea. That's sometimes how it feels when you launch into change. In the end I settled for the more sedate `Lunar Ambitions'. It contained that suggestion of hope and continual striving which are central to the idea of best practice. I will discuss our experiences in this area shortly, but I would firstly like to provide some background to our business. The salt industry is steeped in history and tradition. As one learned commentator observed, common salt is 'a substance seemingly too ordinary to think about, yet it is the oldest of man's raw materials and the basis of some of his newest inventions' (Multhauf, 1978). From ancient times, salt was recognised as a key necessity of life and it has played a role in the rise and fall of governments throughout history. The Romans recognised its importance when they gave their soldiers money regularly to purchase salt, hence our modern word 'salary'. Today, while culinary use remains important, the main consumer of salt is the chemical industry (Figure 1).

Jan 1, 1995

The growth in the nickel market and the price increases predicted in 1970 have not mat-erialized. Several plants have been construct-ed, particularly to treat lateritic ores. A spectacular increase in cost of energy and the escalation of capital costs have led to severe economic difficulties on the part of many nickel producers. Several of the nickel prod-ucers joined together to form a Nickel Develop-ment Institute in 1984 with the prime objective of improving nickel markets. Most producers have taken exceptional action to cut overall costs as well as unit costs. Another organiz-ation made up of nickel producers, NiPERA, was established in 1980, to study and take action on problems of nickel in the environment and especially in the workplace.Ion exchange, and particularly continuous ion exchange, has been developed into a reli-able commercial unit operation in the last dec-ade. An example of how ion exchange combined with hydrogen reduction can be integrated into a Caron type reduction roast ammonium carbonate leach process for the recovery of nickel from laterites is discussed.

Jan 1, 1985

By Coulter K. W

The commercial evaluation of coking coal from bore core data will begin with a technical evaluation of the coal properties affecting coke quality. Methods currently used for prediction of coke.properties from coal analysis are illustrated but in each case accuracy of measurement and prediction should be clearly understood. It is suggested that coal be initially valued from coking properties (base value) and adjusted for chemical properties (merit value). Final evaluation of coal can only take place as coke in the blast furnace where the coke is assessed under high temperature operating conditions. The commercial value of a particular coking coal will depend on many additional factors other than the technical properties.

Jan 1, 1977

Industry can achieve best results via thorough planning, consultatiion with agencies and local communities and a 'hands on' approach to' environmental problem solvingThe Department of Energy and Minerals, through its Minerals Group, has regulatory responsibility for the mining and extractive industries in Victoria. The role of the group is to facilitate the environmentally responsible development of these industries for the benefit of Victorians. It has a wide range of contacts with other government agencies, local government and community groups.The paper is in three parts; firstly, an overview of the nature and contribution of the mining and extractive industries in Victoria; secondly, the industries' regulatory framework; and thirdly, the environmental issues facing the industries and the management of these issues.

Jan 1, 1992

By Dundon P

The Broken Hill Proprietary Company Limited (BHP) is Australia's largest company with widespread commercial interests ranging from steel productin to minerals, oil and gas recovery. While these interests are worldwide, the Company operates or is partner in more than 30 Australian mining ventures. BHP Engineering (BHPE) is the in-house consultant to BHP but is also the largest consultancy in Australia available to general industry. Australian Groundwater Consultants Pty Limited (AGC) is a large, independent consultancy offering specialist services in all aspects of water resources, waste management and environmental engineering, both in Australia and overseas. AGC is particularly well regarded within the mining industry and has a considerable record of providing solutions for mine water related issues. By drawing on the extensive combined experience of AGC and BHP Engineering, this paper will summarize some of the unique ways in which water interacts with and impacts on mining operations in Australia, particularly in matters such as: Slope Stability Drainage and Dewatering Production Cost (Transport, Drilling, Blasting, etc) Water Supply Water Management Tailings and Waste Management Environmental Issues. The paper will also illustrate the cost benefit of providing major engineering works for reduction in total mining cost. It will be shown that, through advance planning and close interaction between outside experts (ie consultants) and on- site personnel, very significant operational cost savings can be made while at the same time achieving a safe and responsible mining environment.

Jan 1, 1988

Ore petrology will fundamentally determine the types of metallurgical processes employed for ore treatment, their operational efficiency and the nature of processing problems encountered. It is therefore paramount that the petrological charact

Jan 1, 1998

By Davis A, Song J

A review of the literature indicated that several studies have been reported on the dissolution of gold using iodide/iodine, bromide/bromine leaching systems. Although the reagent costs are much cheaper for chloride/chlorine (or hypochlorite) this system has not been fully evaluated. This study was conducted to evaluate the fundamental chemistry of the chloride/hypochlorite leaching system. The CHEMIX program was used to model the stability of various gold species existing in the solution. The gold dissolution rate at different conditions was determined using gold strips immersed in various mixtures of chloride/hypochlorite. Leaching experiments were conducted to test the extraction of gold from various ores (oxidised and copper-gold ores), showing a promising prospect for this technique in various applications.

Jan 1, 1992

German coal mining suffers from rock temperatures up to 600C which are the same as in South Africa at 3000 - 4000 m of depth. Therefore cooling plants have increased in the last decade and today a cooling power of nearly 200 MW is installed in the total Ruhr District. Cooling a mine is a little bit different from cooling a bottle of beer in a refrigerator in the kitchen because the heat taken from the bottle of beer is delivered to the kitchen some centimetres away; in mining the cooling-problem is more difficult: here the bottle of beer corresponds to the airflow at the coal face and the kitchen to the surface, So it is necessary to transport the heat or the "coldness" a long distance. In the address by Ieuan Morris some systems for transporting heat from the coalface to the evaporator of the cooling machine and further from the condenser of the machine to a return airflow were described. The following is a short idea of the way this problem is treated in Germany.

Jan 1, 1983

As near surface deposits are increasingly mined out and pit widths beginto exceed the reach of practical direct-casting stripping machines, high haulage costs can make truck-shovel pre-stripping operations uneconomic. This is compounded because the rate of inflation for diesel fuel oil, lubricants, tyres, etc. exceeds the general rate of inflation. The use of conveyor transport systems, long established in terracemining operations in weak materials, e.g. engineering soils, can provide a viable haulage alternative in pre-strip operations and in some open pit settings. The paper describes the engineering requirements and basic economics of such systems.

Jan 1, 1985

By Armstrong ME

The gas bubble energy generated by an explosive plays a major part. in the fragmentation, muckpile movement and damage produced. Previously, the interaction between gas pressure and the rock has been interpreted from a theoretical basis or a qualitative study of breakage mechanisms. A method to measure the fluctuations in gas pressure in rock adjacent to the blast has been developed. This peak pressure will vary with structure, as well as with distance and explosive type. The technique is simple to apply and can be used to observe the flow rate of gas at. varying distances. The apparent velocity of penetration is an indication of whether gas has travelled through pre-existing or blast induced cracks. The technique provides a ?n:eans of determining the suitability of an explosive for a given rock type, depending on the amount of displacement desired. The technique has application in optimir.irig throw blasting and predicting and controlling damage, particularly in highly structured rock masses.

Jan 1, 1986

By Richmond GD

The Hellyer concentrator of Aberfoyle Limited commenced production in 1989 processing a fine grained, massive sulphide ore containing Zn, Pb, Ag, Cu and Au as values. Four concentrates are produced - copper/silver, lead, zinc and bulk (Pb/Zn) - with overall payable recoveries (1991) of 80 per cent Zn, 55 per cent Pb, 50 per cent Ag, 30 per cent Cu and ten per cent Au. Metallurgical development work commenced immediately after plant commissioning, and continues. The flotation response and liberation analysis on a size basis highlighted reagent balance problems associated with tower mill regrinding of sphalerite, poor conditioning of flotation pulps, poor selectivity for fine galena, and insufficient liberation. These were the main causes of values lost to tailings, values reporting to the 'wrong' concentrates and of impurities in the concentrates. Modifications to tower mill regrind circuit operation, and the use of improved conditioning techniques have greatly improved concentrator performance, particularly in the finer (-5 micron) size fractions. Studies of concentrator and laboratory flotation by size and liberation analysis are the basis of diagnostic metallurgy. The techniques used to evaluate the improved concentrator performance are discussed.

Jan 1, 1993

By Rashchenko AF, Voiloshnikov GI, Elshin VV, Khomutov VV

The sorption method for the precious metals recovery fromsolutions and pulps are a perspective trend of modernhydrometallurgy. Russian gold mining industry uses thesemethods, anion-exchange resins being applied as sorbents. Theanion exchange resins allow effective recovery of preciousmetals, however, they have several drawbacks as compared withactivated carbons: high cost of sorbents; difficulties arisingduring treatment of pulps with complex ion composition;necessity of using titanic equipment and thiourea for gold elutionfrom loaded anion-exchange resin and its regeneration.

Jan 1, 1993

By Fermino R

Reduction of waste oxides from steel plant operations was investigated in a laboratory tube furnace at different temperatures and furnace atmospheres. The results have shown that the waste oxide pellets are reduced rapidly to very high degrees of metallization irrespective of the furnace atmosphere and that the reduction is simultaneously accompanied by significant low- ering of the original impurities. It is shown, for example, that treatment at 1000¦C for 30 min. can reduce the Zn content from 0.98% to 0.0065% and K and Na contents from 0.19% and 0.76% respectively, to less than 0.01%. However, pellet strength at 1000¦C was low but this, as shown in the paper, can be very significantly improved by treatment at 1250¦C. The results indicate that the reduction of the waste oxide pellets of this investigation proceeds almost certainly by a chain reaction mechanism and that this principle could be advantageously extended to the reduction of iron ores and other oxides in general.

Jan 1, 1984

By Chia A. H

This paper presents an overview of the development and operation of the PT Adaro Indonesia coal mining project. This operation is an initial two million tonne per annum mine, located in South Kalimantan, Indonesia.The paper places emphasis on some of the more unique infrastructure development and operational challenges that exist in such a remote location environment.A brief summary is also given of the Indonesian coal industry, its direction and position as a significant coal producing competitor for Australia.

Jan 1, 1992

Silver-lead mineralization at Indooroopilly, Queensland, extends upwards from Upper Triassic rhyolite which intrudes phyllite-containing Palaeozoic mineralization.Sulphides and magma were emplaced in a special structural site which underwent dilational fracturing while surrounding rocks were block-faulted and compressed. This site lies at tbe intersection of dykes, faults, and a lineament adjacent to a Middle Triassic granitic stock.Structural controls at Indooroopilly are attributed to the effects of piston faulting. Exploration for similarly controlled deposits should be directed towards structural intersections near stocks or batholiths which have intruded mineralized belts. Priority should be given to structural intersections which were sites of block-faulting and igneous activity under compressional tectonic conditions.Favourable sites lacking surface mineralization may contain ore at depth as piston faulting produces 'blind' ore deposits.

Jan 1, 1976

By Mckenzie CK, Scott A

The injection of coal as an auxiliary fuel in ironmaking blast furnaces has been introduced on many furnaces worldwide. This paper examines the present practice of coal injection and discusses future directions for the technology. This has been undertaken through the use of a heat and mass balance model which predicts the replacement rates of coke by coal and the effect of coal injection on blast furnace productivity. The results indicate that future pulverised coal injection could replace substantial quantities of metallurgical coke, but that the energy balance economics of individual steel plants will have a dominating influence on the future of the technology.

Jan 1, 1987

AND INTRODUCTION The Lochiel coal deposit, a large Tertiary soft brown coal deposit in the mid north of South Australia, is currently being investigated by the Electricity Trust of South Australia (ETSA) as a potential source of fuel for a base load power station. Feasibility studies indicated that the proposed dragline method of overburden removal was viable but economically sensitive to both highwail and dump batter angles. The unusual properties of the unconsolidated overburden sediments and the groundwater regime posed a number of intimately related hydrogeological and geotechnical questions which were addressed before and during the excavation of a trial pit. All strata at Lochiel are of soil strength, and artesian aquifers occur above and below the coal. From the initial evaluation of the deposit a number of hydrogeological questions were defined. These related to the rate at which the pore pressure in the silts is reduced by dewatering, the extent of the reduction in pore pressure due to prestripping, and the feasibility of dewatering and depressurising carbonaceous silty sand sequences. The site of the trial pit was selected to answer these and other questions from the basis of a detailed geological, hydrogeological and geotechnical understanding. The trial pit dewatering system simulated a full scale mine dewatering system and included ten pumped wells, twenty drainage wells, and nearly 400 monitoring instruments. It operated from September 1986 to June 1987. The excavation was carried out between February and May 1987.

Jan 1, 1988

By Singer RP

The Latrobe Valley brown coal deposits are one of Australia's major energy resources with measured and indicated reserves amounting to some 162 billion tonnes. Economically recoverable reserves are estimated at some 65 billion tonnes, 47 billion tonnes of which are classified as available for mining (VBCC (1983)). These deposits contain one of the lowest grade fuels used anywhere in the world. Typical Net Wet Specific Energy values range from 6 to 9 MJ/kg. Despite the low energy value of the raw coal, the Latrobe Valley deposits represent approximately 90% of Victoria's indigenous non-renewable energy resources. Utilisation of this vast primary energy resource has been a key factor in the economic development of Victoria.

Jan 1, 1990

By Walker V

The 'MAGNADET' to provide a safe enhanced protection extraneous currents, electricity and radiodetonator was designed electric detonator with against the effects of current leakage, static frequency energy.It has found a particular niche in shaft sinking operations and Mount Isa Mines initiated trials of the system in 1983 as part of the design work for the 3000/3500 orebody access shaft.Initial surface blasts indicated a number of significant advantages which were confirmed during the bench and concrete phase of the M37 shaft sink. The application of 'MAGNADETS' was later extended to the horadiam phase of the project.Details of the exploder capacity calculations for the various M37 round designs are included with the paper.

Jan 1, 1985