Search Documents

By Turnbull AG

The direct smelting of zinc sulfide con- centrates has been investigated by an extensive series of computer-based thermodynamic equili- brium calculations. The study covers both pure 7.n-S-O-C-N systems and practical concentrate- coal-air-flux systems. It is shown that for a zinc concentrate containing iron and lead sul- tide impurities, a 97% yield of zinc vapour with autogenous operation can be obtained under carefully optimized conditions. The possible integration of this process with existing zinc condensation and recovery processes is Discussed.

Jan 1, 1980

By Misk A

Several logging methods are presently available to the oil industry for the evaluation of formation porosity: the Sonic and Neutron logs are already widely used, the Gamma-Ganmia log is being progressively introduced. The readings of these instruments are primarily a function of the rack-porosity, hence the general term of "porosity tools". Apart from porosity, however, other variables such as type of fluid in the pores, nature of matrix and degree of shaliness have an important influence.The response of each device is a different function of such parameters: therefore, a cci bination of porosity tools can lead to information on these variables in addition to the evaluation of effective porosity.For example, the presence of gas; rather than water or oil, in a formation which is not deeply invaded, will tend to give Neutron derived porosity values which are too 'low; on the other hand, the Sonic derived porosity: value will be too high in such- a case. For the same porosity, the Sonic gives a longer transit time in sandstone than limestone, whereas in the low porosity range, the Neutron will read more counts per second in a sandstone than in a limestone of the same porosity. The presence of shale also affects the readings of the various porosity tools in different ways so that the combination of two or more methods may lead, in some cases; to an evaluation of both the-effective porosity and the shale, content.In conclusion, it may be said that the various porosity tools pre-sently available, are, to a large extent, complementary, and that in many problems the use of two porosity tools, instead of one, is very likely to bring valuable additional information.

Jan 1, 1962

By A S. Derrington

This paper describes a hybrid ventilation system, which uses secondary fans that also act as de-facto primary fans to extract fresh airflow from the mine intake raise system. Also discussed are the associated problems such as uncontrolled recirculation, inadequate decline airflow, fire safety issues, prolonged blast fume clearance times, high air temperatures in main access routes, neutralisation of mine air cooling by heat from secondary distribution fans, increased ventilation system complexity, reduced flexibility and high pressure differentials (which cause safety issues with personnel access and reduce secondary ventilation system performance).Practical suggestions are provided on options to avoid these problems listed.CITATION:Derrington, A S, 2013. A critique of the push-pull hybrid ventilation system, in Proceedings The Australian Mine Ventilation Conference , pp 73-78 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By Nag D. K

The Dolphin Scheelite orebody is located near the old mining town of Grassy on the south-east comer of King Island in Tasmania. Surface open cut mining of the Dolphin deposit was conducted for a number of years, then the proximity of the sea and adverse stipping ratio led to underground mining. As a result of the variable orientation and dimensions of parts of the orebody a number of mining methods were practiced at the Dolphin mine until 1990 when a combination of high processing and surface site costs coupled with low tungsten prices led to the cessation of operations. In this paper the different mining methods practised are examined and critically reviewed. The more successful mining methods were developed with experience and improving equipment technology to the extent that the underground operation produced ore at the lowest unit cost during the final years of operation.

Jan 1, 1995

By Eggleton T, Taylor G

The lateral and vertical distributions of gold and a wide range of other elements in the regolith, close to Au and Cu mineralisation have been investigated at Goonumbla, NSW. Open cut mining has exposed deeply weathered profiles which have been used for this investigation. Determination of secondary mineralogy and micromorphology of profiles have facilitated the broad interpretation of processes that determine element mobility and dispersion from primary mineralisation as a result of weathering. This in turn has led to better interpretation of geochemical data and enhanced understanding and knowledge of regolith geochemical processes which are invaluable in the formulation of improved exploration Procedures.

Jan 1, 1997

ICI Australia has been developing PC-based software to assist the blast engineer to design and monitor open pit blasts. The scope of this software differs significantly from commercially available mine design packages.The software is designed for routine use in a normal production environment. The system enables the engineer to produce practical documents which include: a drilling plan, a loading sheet, a hook-up diagram, an inventory of explosives and auxiliary items, and other data on the blast such as tonnages and powder factors.

Jan 1, 1992

By T G. Vizcarra, T J. Napier-Munn, A T. Karbowiak, M G. Hart

Squeezing extra performance from existing equipment (‘sweating the assets’) is key to continuous improvement initiatives, particularly during times of cost cutting where the option of spending additional capital to facilitate circuit upgrades can be severely constrained. A common challenge, however, is identifying the best combination of settings for different process variables, as their effects can be camouflaged by interactions with other process variables and, of course, noise in historical data.This paper describes a recent investigation at Boyne Smelters Limited to identify strategies to coarsen the product of its dry, fixed-speed, open-circuit AG mill, without the need for installing pre-screens prior to the mill. The product is used as insulation material for the reduction of alumina to aluminium, and an excessively fine product was inhibiting the ability of the cover material to dissipate heat from the underlying anodes. The approach was to undertake a series of experiments, designed according to statistical criteria, to elucidate the effect of key process variables (feed blend and power draw) upon the product sizing. The results provided clarity about what strategies would encourage the production of a more desirable mill product (with some surprises). The study is a good example of how properly designed experiments can identify hidden potential in processing circuits, thereby mitigating the need for capital-intensive upgrades.CITATION:Vizcarra, T G, Hart, M G, Karbowiak, A T and Napier-Munn, T J, 2018. Getting the most from existing processes: using cleverly designed experiments to optimise the line 3 AG mill at Boyne Smelters Limited, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 207–216 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By P J. Scales, D Boger

Technological advancements in mineral processing have increased the feasibility of refining low-grade ores. Because of this progression and continual depletion of high-grade ore deposits, much larger volumes of waste material are produced. At the same time, increasing environmental legislation and cost competitiveness dictate that these wastes be disposed of in a manner that is both environmentally acceptable and economically viable. To achieve these criteria, many mineral processing industries are dewatering waste streams in order to reduce the volume of tailings and increase water and reagent recovery. The subsequent dry disposal of these highly concentrated mineral tailings requires a thorough understanding of the effects of dewatering on the flow characteristics. Dry disposal represents a paradigm shift in engineering. The tailings are engineered to suit the disposal requirements, as opposed to engineering a facility to accommodate the tailings. It is therefore important to understand how the material properties and operational parameters can be modified to produce the desired tailings flow and deposition characteristics. As concentrated suspensions usually exhibit non-Newtonian behaviour, determination of the disposal plant operating conditions requires a thorough understanding of the rheological characteristics of the material. The implementation and optimisation of dry disposal methods involves three concurrent and interdependent rheological studies to determine:the concentration required to achieve the optimum spreading and drying characteristics of the tailings once deposited; the optimum conditions for pipeline transport; and the feasibility of dewatering the slurry to the required concentration. The paper presents an overview of the issues pertinent to management of the flow properties and processing of dewatered waste streams.

Jan 1, 2002

By D Nieuwkerk, V J. Absolon

"Screw press technology is an innovative approach to tackling the growing pressure to conserve water and minimise the environmental impact of mineral tailings disposal. The principles of the technology have been known for a considerable period of time in non-mining applications such as water treatment, wastewater (municipal sludge), as well as in the paper and chemical industries for dewatering solids, particularly those containing clays.The screw press represents a viable niche technology for filtering fine and high-clay tailings, without the prior thickening stage, and is capable of producing a filtered product that is sufficiently consolidated and dry enough to provide a product suitable for conveying and dry stacking.The Ishigaki screw press was introduced in 1990 and key features are: continuous operation and excellent availability low wear to plant acceptable flocculant consumption low carbon footprint and low noise levels fully automatic.These features lead to simpler plant layouts, easier maintenance, smaller spares inventories, reduced wear, smaller footprint and overall lower capital and operating costs.The amenability of a particular tailing stream to treatment by screw press technology may be determined by test work. Two pilot plant studies are described where this technology has been applied in the mineral industry being flotation tailings from a rare earth (RE) mineral concentrator and coal tailings. In addition, preliminary details are given of an ACARP sponsored research program titled ‘The application of screw press filtration in tailings dewatering’.CITATION:Absolon, V J and Nieuwkerk, D, 2014. Innovative use of screw press filtration in tailings dewatering plant design, in Proceedings 12th AusIMM Mill Operators’ Conference 2014, pp 449–456 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 1, 2014

By Adranyl W. W

Sub-level caving with bottom ore drawing has gained wide acceptance in rich, soft, low magnetic iron ores because it provides moderate ore dilution and ore losses. The main problem here is the high rock pressure exerted on sub-level drives situated in the sub-level sill pillars. To reduce this effect, the ore block is divided into panels. This paper illustraes the method of determining the maximum panel width providing low maintenance cost of sub-level drives.

Jan 1, 1995

By M Thompson

"The Jaguar concentrator, 60 km north of Leonora, Western Australia (WA), consists of a standard closed circuit semi-autogenous grinding (SAG) and ball mill producing a float feed of approximately 60 micron at 70 t/h. Following comminution, separate copper and zinc concentrates are produced by differential flotation. These concentrates are subsequently dewatered by thickening and then filtration.Separate audits of the Jaguar Operation’s copper and zinc concentrate thickeners were conducted to evaluate their performance, following occasions where site personnel had identified unnecessary loss of copper and zinc concentrate to the thickener overflow. The feedwells were identified as the source of the observed problems due to the following issues with their design/duty:lack of retention time in the feedwell as current design is completely opennot conducive to effective mixing required for efficient flocculationdiameter of the zinc concentrate thickener feedwell was undersize for its duty.To improve the performance of the thickeners, it is planned to replace both concentrate thickener feedwells with a high rate design for their respective duties in February 2016. The audits also identified that the feed system requires modifications with particular importance placed on minimising air entrainment of slurry into the thickener feedwell. Minimisation of air entrainment is hoped to be achieved by providing constant head pressure through installation of weir arrangements in the feedboxes and redirecting each feed pipe so that it feeds tangentially into the feedwell. In addition, improvements to the control philosophy of both thickeners will be made with the installation of an ultrasonic bed level probe and bed mass sensor, in order to make real-time adjustments to the underflow pump speed to maintain steady state operation.Following the feedwell replacement and modifications to both thickeners it is expected that losses of recovered copper and zinc will decrease to undetectable levels. Subsequently it is anticipated that a more consistent, homogenous underflow can be produced for downstream filtration.Citation:Thompson, M, 2016. Concentrate Thickeners Feedwell Replacement, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 273–278 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By Shining Z

The strength and deformation of more than two hundred coal samples have been tested in the condition of triaxial compression. The regression equation showing the relationship between coal strength and pressure in the pores, as well as confining pressure, was obtained. The appropriate calculation for stress-strain curve was carried out. Further, an analysis shows the variation of coal strength and its modulus of elasticity in methane medium.

Jan 1, 1992

The necessity for good management and economic working in our mines and ore-dressing sheds is impressed upon us by the present low prices of all our metals. Silver, lead, copper, and tin have all suffered a heavy decline during the last six or twelve months, and many mines have been shut down simply on account of the low market value of the ore produced. After fully considering the position of the mining industry. I am convinced that considerable improvements will have to be made to make it as prosperous as it ought to be. The most obvious of these improvements are good management, good machinery, and as little interference by directors as possible. If these conditions are insisted upon and carried out efficielltly a poor mine may have a chance to weather the storm.There is no doubt that the present depression is the refilult of over-speculation and general loss of confidence by which the whole commercial system has been affected, and every branch has suffered more or less, mining not excepted. It has suffered heavy losses in the past, and the future is not over bright we are, therefore, compelled to be careful in everything by which mining is affected and savings can be secured.

With some notable exceptions, marine placers located just below, or just above, present sea level, are responsible for much of today's production of detrital ilmenite, rutile, zircon, and other minerals of value. The purpose of this paper is to discuss the paleogeographic and paleo-oceanographic factors which may have determined the location of presently submerged marine placers. These factors-include changes in sea level, burial by recent marine sediments, stream capture and other i changes in drainage patterns, and recent changes in climate. Selected geologic situations in the Yellow Sea off the coast of Korea, in the Atlantic Ocean off the coast of Portugal, in the Bering Sea off the coast of Alaska, and in the Arabian Sea off the coast of India, will be used to illustrate the author's point of view.

Jan 1, 1980

By Henderson J

Iron ore samples selected from the Deepdale, Iron Prince and Mt. Newman ore bodies have been pelletised on a pilot scale plant and subsequently reduced under laboratory conditions by hydrogen or carbon monoxide. Pellets approximately 1 cm in diameter have been reduced by hydrogen over the temperature range 5000- 900¦C and the results examined by thermogravimetric, microscopic, electron probe and x-ray techniques. After an initial time delay it was found that up to 95% reduction the rate of reduction could be described by a transport con- trolled porous model, in which the effective diffusivities of hydrogen in theòpr¦duct layer and the reaction zone are filar. Independent measurements of effective diffusivity supported the values obtained from the reduction data. ve 95% reduction the rate decreased markedly due to the formation_of retained wustite or fayalite. Comparison with reduction by carbon monoxide over the temperature range 7500 - 900¦C showed that the rate eduction by carbon monoxide was approximately five times slower than the rate by hydrogen. The rate of reduction was found to be a function of the properties of the pellets, which may account for the ely conflicting results that have been obtained in previous investigation on porous pellets.

Jan 1, 1970

The efficient design of carbon-in-pulp (C.I.P.) plants involves the integration of both process engineering and design engineering.Many recently constructed plants have not recognised the above interrelationship, and as such have incurred higher capital and operating costs than were in reality necessary. This has been compounded in some cases by slavishly following the design of plants where process conditions are different for the ore characteristics in question, thus perpetuating design errors that finally become industry "accepted practice".In the paper that is to be presented the unit operations of crushing, grinding, classification, leaching, adsorption, desorption and electrowinning in C.I.P. plants will be discussed with reference to the integration of process and design engineering.

Jan 1, 1986

In the early ages man contented himself with the use of such tools and appliances as would assist him in the enlightenment of his labours. With the advancement of science, numerous motives, with modifications and adaptations, have been introduced to enlighten labours, and in many cases have taken the place of man, but it can hardly be said that this applies to shovels, although one of the oldest implements of labour; certainly, with the introduction of the steam shovel the labours of man have been considerably reduced, but the hand shovel of today is used similarly to that of years ago.If the principle of the hand shovel has not been improved upon, it must not be suggested that the manufacturers of this article are not endeavouring to improve its quality, and the main point with which the manufacturers have to contend is the production of an article which will give a maximum of durability combined with a minimum of lightness. In order to accomplish this they must select suitable material, and subject it to such heat treatment process that will produce a shovel having a maximum of hardness and toughness without being unduly brittle, and which will withstand the excessive wear to which it is subjected.In this article an endeavour will be made to explain (a) the manufacture of shovels; (b) the defects commonly met with-the cause of same and measures which are necessary to remedy them.Before doing so a brief description will be given of the class of steel used for shovels; this is an important factor, and a steel which is admirably suitable is a plain carbon one containing approximately 55 - 70% C., and closely resembles that used for the manufacture of railway rails. This plain carbon steel is very extensively used, although at present alloy steels are being utilised to a certain extent for shovel manufacture, and with suitable heat-treatment.

Jan 1, 1926

By Houchin MR, Jenkins DH

This paper examines the importance of processing to the properties and performance of high purity zirconia ceramics. Many of the principles discussed, however, apply to ceramic processing in general. For fabricated ceramic articles to display their wide range of high performance properties, they must be made fully dense. The precursor powder and postpowder processing requirements necessary to achieve full density in the fabricated body are discussed. Brittleness, the anathema of ceramics, can be overcome in zirconia by incorporation of toughening mechanisms. Transformation toughening and microcrack toughening and their origins in partially stabilized zirconia are reviewed.

Jan 1, 1989

By G Newling

Zinifex Rosebery Mine is a lead-zinc underground mining operation located at the base of Mount Black, on the West Coast of Tasmania. Mining activities at the Rosebery Mine have been undertaken for over 100 years, and it has been operating in its current form for over 60 years. A large surface and underground exploration drilling program over the last 18 months has increased the mineÆs expected mine life from five to 12 years, with expectations that over the next 18 months as the program continues this will swell to 20 plus years. Zinifex Ltd secured Rosebery Mine in April 2004 and commissioned a detailed life-of-mine (LOM) study on all aspects of the operation. One of the most detailed sections of this report was on the state of the current ventilation system. It was identified in this report that for mining at the current depth of approximately 1100 m to continue a minimum 30 per cent increase in ventilation quantity was essential, as well as a likely requirement for a refrigerant cooling plant for each of the two deepest panels, the K and P lenses. It was identified that Zinifex did not have personnel with the expertise in underground refrigeration to manage and implement a project of this nature. A second report was commissioned with Bluhm Burton Engineering (BBE), a South African firm specialising in both surface and underground large-scale refrigeration plants. BBE concluded that two refrigeration plants were required to provide the necessary cooling power in the lower sections of the mine. In 2005, with BBE as technical consultants, Zinifex Rosebery Mine embarked on a project to commission two underground refrigeration units capable of lowering the wet bulb temperature at the decline face by four degrees centigrade. This paper is intended to give the reader an overview of: Rosebery Mine operations,Rosebery underground refrigeration project,technical difficulties associated with implementing an underground refrigeration system, andkey learnings to date.

Jan 1, 2008

By D A. Kepert, D Clark

During early 2004, Fortescue Metals Group (FMG) began an aggressive exploration and drilling program in the Chichester Range, targeting iron enrichment developed in the Nammuldi Member at the base of the Marra Mamba Iron Formation. The timely recognition by FMG of distinct zones of (hypogene) microplaty hematite (mplH) enrichment overprinted by extensive supergene mineralisation led to an early reappraisal of the geological history of the area and characterisation of the possible structural and stratigraphic controls on mineralisation. Regionally, the Chichester Range dips gently at less than 5¦ to the south, however, detailed mapping shows that this regional limb is overprinted by low amplitude, long wavelength, north/south to northeast/southwest trending folds. The locations of major structures in the Marra Mamba Iron Formation, combined with spectral analysis of known mineralisation, allowed extrapolation and prioritisation of exploration target areas. The delineation under cover and understanding of these structures was enhanced by detailed airborne magnetic data. Recognition that supergene mineralisation was associated with a palaeotopography that continued significantly under cover to the south under sediments of the Fortescue River valley led to the discovery of extensive supergene mineralisation together with additional mplH mineralisation. A model for the landscape evolution and preservation of enriched Nammuldi Member was generated in order to help communicate both the complexities involved with targeting drill holes beneath cover and the potential limits to the lateral extents of mineralisation.

Jan 1, 2005