Search Documents

The recent installation of top gas temperature probes in blast furnaces at Australian Iron & Steel Pty. Ltd. - Port Kembla, has provided the means for studying radial gas flow distribution in blast furnace shafts. This paper describes the top gas temperature probes and outlines their development and results of initial studies aimed at obtaining a suitable relationships between temperature profiles and furnace parameters. The effects of various combinations of burden materials have been outlined by the results reported. The use of probes has also helped to clarify the effect of casting cycles on furnace operation leading to increased emphasis on the reduction of the interval between gun-up and drill-out. Areas for future studies are also broadly Outlined.

Jan 1, 1975

By Vutukuri VS, Budavari S

During recent years many investigators have suggested large spacing to burden ratios to improve the fragmentation obtained in blasting. In spite of these suggestions, most operators still use a conventional ratio of 1 to 2. From single hole longitudinal charge tests in laboratory, it is shown that burden controls the fragmentation. The burden for obtaining uniform fragmentation is smaller than the burden to obtain maximum breakage. Tests on two or three holes show that a larger spacing to burden ratio can be used for smaller burdens, but it is not possible for the larger burdens chosen to obtain maximum breakage. By using finite element analysis evidence is presented to show the effect of spacing and burden relationship on blasting results.

Jan 1, 1975

Utah's Blackwater mine began operations in 1967. The four CQCA mines controlled by Utah followed over the period 1971 to 1979. Project feasibility studies for all these were based on open cut mining to overburden depths of 60 metres, with typical project lives of 12 to 16 years, depending on reserves Further studies, initiated after the mines had started, showed that continuation of open cut mining beyond the 60 metre highwall was viable. In 1973, the Deep Stripping Project (DSP) was launched to define the scope for stripping deeper, to determine what the additional equipment needs might be, and to pu forward proposals for a full scale trial system. The project commenced at grass roots with a literature survey, proceeded through a sequence of equipment evaluation, specification, design and manufacture to the commissioning of the Goonyella BWE system. Studies are continuing to assess the future deep stripping requirements for all Utah's Bowen Basin mines.

Jan 1, 1983

By Susanto A

As part of the current NERDDC funded project studying Dragline/Hopper/ Crusher/Conveyor systems for overburden removal, an investigation was carried out to assess the feasibility of automating the swing-to-dump phase of the dragline digging cycle in order to main- tain consistent performance of spotting the bucket above the hopper prior to dumping. The study involved design of automatic position controls for the hoist, drag and swing drives and simulation of detailed mathe- matical models of the three electromechanical systems and their associated electrical control schemes. The design of the hoist and drag systems to position the bucket in the boom plane is relatively straightforward. Simulation results show fast and accurate performance, with no evidence of interaction between the two drive systems through the ropes. The design of the swing position control system involves special strate- gies to cater for variable inertia and to damp the pendulum oscillations of the bucket. The use of a bucket pendulum model and variable dynamic compensation embedded within the feedback control loop, along with optimal speed/angle slowdown trajectories, has yielded fast and damped positioning responses under simulation.

Jan 1, 1989

By Fowler T. J

Examples are provided of discontinuity analysis at selected sites in central Victoria. Discontinuities are rock fractures of low tensile strength, including bedding, foliations and joints, which are analysed during rock excavation design, to quantitatively determine the defect orientations, spacing and lengths. Their analysis can reduce the cost of mining operation and improve safety. Extrapolation beyond the exposed face is required, although difficult without an understanding of the regional geology. For rock engineering purposes assumptions are commonly made that discontinuity characteristics are uniform throughout the rock mass, however this is often invalid, as rock masses have usually undergone large-scale deformation, exhibit anisotropy and inhomogeneity. Structural geologists are able to interpret large-scale deformation responses for the purposes of structural correlation and extrapolation. Examples of discontinuity analysis linked to regional geological assesment from sites in central Victoria, reveal that discontinuities exhibit similar characteristics in a range of rock types of different ages and composition. Spacing variations between individual sites are believed to be a result of local rock type differences.

Jan 1, 1997

By Stone AM, Romensky G

The requirement for economic operation of unit trains carrying bulk materials has dictated that rapid and accurate bulk loading methods be provided. The train loading station at Phosphate Hill, built for Queensland Phosphate Ltd. to load rock phosphate, provides this facility and whilst the concept used is not unique, it contains a number of novel features that are considered to advance the "state of the art'' in this field. This paper briefly reviews some alternative concepts evaluated, and describes the design and operation of the scheme ultimately selected as being most appropriate to the project requirements. it is one which utilises a variable speed belt feeder whose speed is controlled in proportion to the weight rate of material moving on the belt as measured against a set point

Jan 1, 1978

This study begins with the semivario- gram modelling of variables rutile grade and clay content from a beach sand rutile deposit. This is followed by two dimensional block kriging. The deposit was divided into blocks of 30 x 30 x 1.5 m dimensions and the kriged estimate together with the associated kriging variances for each variable within each block were determined. Finally, using the results of the krig- ing program and considering the acceptable limit of clay content together with the cutoff grade for rutile, a method for optimization of mineable thickness and hence the tonnage of ore was applied and the results were dis- Cussed.

Jan 1, 1986

By C R. Sundberg

Despite nearly a half-century of continuous production, the low-grade iron ore (taconite) deposits of North America remain economically competitive sources of raw materials for the domestic steel industry. The continued viability of these mature integrated mining-concentrationagglomeration complexes requires highly efficient utilisation of assets, especially the mineral resource. At Cleveland-CliffsÆ five North American managed operations, enhanced ore characterisation techniques are playing a critical role in their continued success. Due to the low-grade nature and complex mineralogical composition of these deposits, ore characterisation cannot solely rely on assay grades. Historically, taconite ore characterisation has augmented assay grades with bench-scale concentration tests to quantify recoverable mineral. The economic necessity for improvements in mill efficiencies and final product quality has mandated significantly greater knowledge of ore-related impacts. Cliffs Technology Center has met this challenge by developing a variety of novel iron ore characterisation techniques. The applications developed include both in situ and laboratory procedures, plus unconventional data integration methods uniquely suited for these deposits. This paper details the evolution of these novel ore characterisation techniques and their application to each phase of the operation: mining-concentrating-and pelletising. The improved ore characterisation techniques have contributed to successes at individual Cleveland-Cliffs managed operations including mineral recoveries exceeding 95 per cent and productivity increases exceeding ten per cent while consistently achieving customer product quality objectives.

Jan 1, 2002

By O Dahl, I M. Platten, E J. Sides

Many narrow-vein gold deposits are characterised by a high to extreme nugget effect and the presence of coarse gold. They rank amongst the most difficult of deposits to produce an accurate and precise resource estimate. This contribution presents a case study from the Nalunaq Gold Mine in Southern Greenland. The mine commenced operation in May 2004 and is currently operating at a rate of 400 tonnes per day, to produce about 100 000 oz gold per annum from a total resource base of 1.2 Moz. Mineralisation is characterised by quartz veins that are hosted within a shear zone that is continuous over about 1000 m. The principal orebody is the Main Vein structure, which ranges up to 3 m in width, maintains an average dip of 35¦SE, and contains significant gold grades (1000s g/t Au). Gold particles are often visible, with 25 per cent being greater than 250 microns in size. Variography using underground development samples indicates a nugget effect of about 75 per cent. For the 2005 resource estimate, a 2D metal accumulation ordinary kriged block model was used to produce a global grade for the Target and South Blocks of the Main Vein. Grade control chip-channel samples are collected from æshantyÆ drive footwalls, and used as the basis for both the kriged block model and to determine the grade of individual stope blocks by peripheral weighted averages. Geology plays a key role in mining efficiency, given the locally variable nature of the ore zone.

Jan 1, 2006

By Young D. R, Webb I. D

The hydro-chlorination of Fe2O3 and Fe304 has been investigated in the range 850-950¦C in order to elucidate the role of iron in the segregation process for nickeliferous laterites. The kinetics of Fe203 chlorination using 20% HC1 - 80% N2 gas mixtures is consistent with a single-stage structure control model, whereas Fe3O 4 exhibits a two-stage reaction mechanism. Oxygen potential measurements using a CSZ probe located above the bed and X-ray powder diffraction results confirm the proposed reaction scheme. When a serpentine nickeliferous laterite (1.03% Ni - 11.7% Fe) was chlorinated at 900¦C with a 20% HCl - 80% N2 gas mixture it was found that the iron oxide in the ore was extracted in a similar manner to the synthetic iron oxides. Also, it was found that the nickel extraction from the ore paralleled that of the iron and the tests indicated that for the major part of the extraction, the solid nickel species were in equilibrium with the gas phase. The recovery of nickel from laterite ores by the segregation process has been investigated by a number of workers and several extensive reviews of the literature associated with this field have been published (Iwasaki, 1972; Canterford, 1975; Wright, 1973).

Jan 1, 1987

By A Xenidis, N Papassiopi, I Paspaliari

Acid generating sulfidic tailings covering a surface area of approximately ten hectares have been deposited in the historic mining area of Lavrion in Greece. For the development of a remediation strategy, the performance of three alternative acid generation control techniques was assessed under actual field conditions. The techniques involved the application of dry covers, including a synthetic HDPE liner and a compacted clay layer with capillary barriers. Furthermore, the potential formation of a low permeability hardpan layer at the sulfidic tailings surface by limestone addition was investigated. The field tests covered an area of 2500 m2, which was divided in equal quadrants, corresponding to the control plot and the three alternative remedial options. To monitor the amount and quality of percolated water, lysimeters were installed beneath the four plot areas. Based on the monitoring results over a period of six years, due to the dry climate encountered in the Lavrion area, a low amount of water percolates through the pyrites if no action is taken (control area), corresponding to 20 - 25 mm per year. This water is highly acidic, pH = 1.2, and contains a heavy load of contaminants, eg Fe 40 g/L, Zn 15 g/L, and As 1.5 g/L. The HDPE cover eliminated the percolation of water into the material for a period of five years, whereas thereafter the volume of leachates increased to values similar to those recorded in the control plot. The water collected in the lysimeter of the clay cover has been minimal corresponding to approximately five per cent of the drainage volume produced in the control area. In the fourth plot, which involved limestone addition to sulfidic tailings, the volume of drainage initially collected was almost double compared to the control area. After three years of monitoring, significant reduction in the amount of percolated water was observed, attributed to the formation of a cemented layer (hardpan), at a depth of 40-80 cm from the testpad surface.

Jan 1, 2003

By Greaves M. C, Amos M. D

A study was made of the instrumentation and technique of atomic absorption spectroscopy developed by Walsh of the Commonwealth Scientific and Industrial Research Organisation (CSIRO), Australia.The method was evaluated for the determination of silver in lead sulphide concentrate. The precision of the procedure developed is equal to that of the uncorrected fire assay method and the accuracy is greater.Brief mention is made of the use of this technique for the determination of silver and other elements in ores and concentrator products.

Jan 1, 1994

By Liu Z. C

Evans' theory for chisel shaped picks is well known in the field of rock cutting technology. It has been widely accepted as a good mathematical description of how coal and other rocks break under the action of a simple wedge or chisel. Subsequently, Evans proposed a corresponding theory for pointed shaped picks. Theory along with experimental evidence from the laboratory has consistently shown that chisel picks are more efficient than pointed picks. However despite such evidence, pointed picks continue to be the preferred shape in most practical cutting applications. Evans' theory for pointed picks was developed in an attempt to shed light on this apparent incongruity. The theory although predicting forces of the right order was found to be deficient in several respects. This paper examines Evans' theory for pointed picks and proposes changes to it, which brings the theory much more into line with measured data. The issue of the relative efficiencies of chisel and pointed shaped picks is also examined on a theoretical basis and the apparent incongruity is Resolved.

Jan 1, 1995

By T Muri

The drying operation of materials from particulate solids, through slurries and suspensions, to continuous sheets represents an important part of several processes in the chemical and mineral industries. The increasing demand of high productivity at low cost and minimal environmental impact makes it complex to evaluate and choose the best available drying technology for each industrial application. The drying technologies are mainly characterised on the basis of how the wet product is related to the drying medium, namely: direct and indirect drying. In the direct drying method (convection drying), the product is brought into direct contact with the drying medium, which may be hot gas or air. Large quantities of gas are necessary for transfer of the required energy. A special case of the direct dryer is the fluid bed dryer, in which the product floats on a cushion of air or gas. The process air is supplied to the bed through a perforated distributor plate and flows through the bed of solids at a velocity sufficient to support the weight of particles. Very high heat and mass transfer values are obtained as a result of the intimate contact with the solids and the relative velocities between individual particles and the fluidising gas. In the indirect drying method (conduction or contact drying), the wet product is separated from the drying medium. The drying unit can consist of a rotor forming the indirect contact heating surface mounted in a stationary or rotating shell. The indirect method uses saturated or superheated steam resulting in low energy consumption and minimal environmental impact. In this paper, a review is given of the technologies available on the market based on different drying methods. The advantages and the disadvantages are summarised with respect to issues such as investment and operating cost, maintenance, product capacity, product handling and environmental impact.

Jan 1, 2006

The occurrence of metallic minerals in Australia to the time of the proclamation of South Australia as a Colony in 1836 was unknown. It is, therefore, perhaps, surprising that British settlers arriving in the Coromandel included among their number a German scientist Johannes Menge who had been appointed by the South Australian Company to the post of Mine and Quarry Agent and Geologist on 1 July 1836. His instructions were to `explore the natural productions of the Colony above and below ground and to superintend the working of quarries of stone and slate, the boring for water, metal, lead, coal and other mines at a salary of ú150 per annum for one year and for as much longer as the Company require your services not however exceeding five years'. In the event, he was to have little influence on those matter.

Jan 1, 1993

By Mark C

Designing coal pillars to provide resistance against overburden loads has long been an aim of rock mechanics engineers. The need for accurate pillar strength models has become.more urgent as greater overburdens are encountered and pillar sizes grow larger. Current pillar design models differ widely in their predictions of the trend in pillar strength with increasing pillar width- to-height ratio. The goal of this paper is to evaluate current pillar strength theories, using a comprehensive data base of stress measurements from coal pillars. The stress measurements indicate that coal pillars maintain relatively high stresses near the ribline, and that the stress gradient within the yield zone can be approximated as a straight line. Several problems are identified for further research, including calibration procedures for different types of stress cells, strain softening behavior in the yield zone, and measurement of stresses in the cores of very wide pillars.

Jan 1, 1992

By Tyson G. R

A novel system has been developed using computer imaging techniques to make on-line measurements of material on a moving conveyor. Meas- urements of the mass or volume of conveyor materials are important in large open pit mining operations such as those operated by the State Elec- tricity Commission of Victoria (SECV). Such on-line measurements can be used for monitoring and controlling the production and transport of coal or overburden, and to assist in maintaining production levels. This paper describes a conveyor burden volume measurement system which is currently under development at the Research and Development Department of the SECV and although targeted initially for use in the Commission's open cut mines, the system is suitable for use on any open conveyor system. A basic developmental system has been built to demon- strate the viability of the technique used and further work on the system is planned. The measurement technique and the major components which have been developed as part of the system are described, some comparisons are drawn with other existing measurement systems and potential errors and future development are discussed.

Jan 1, 1989

By Gray J, Krouse HR, Changkakoti A, Morton RD

A group of stratabound-stratiform Fe-Ba-Zn-Pb-Ag deposits within the La Minita mining district of Michoacan, southwest Mexico have been investigated. The results of the study show that these deposits were generated around submarine hot-springs issuing in a Cretaceous island-arc environment. The exhalative mineralization, which is both epigenetic and syngenetic in character, was developed above fault-systems which constituted the loci of both volcanism and subsequent hydrothermal systems.Fluid inclusion data suggest two hydrothermal events during ore mineralization, one at 240¦C and the other at 161 to 205¦C, with salinities between 2.1 and 12.8 wt.% NaCl equivalent. Stable isotope data support a marine origin for the ore-fluids, as well as, for carbon and sulfur. Strontium isotope data suggest that Sr in the barites was extracted from the volcanics and limestones by circulating seawater. The ore-depositional environment was one of shallow, sub-tropical marine character, where mineralization was in part geochemically controlled by carbonate reefal facies within the volcanic/pyroclastic suite.

Jan 1, 1990

By Best R. J, Poulos H. G

The method for design of primary roof support for the large todoidal cavern constructed to house the Sydney Opera House parking station is presented. The cavern was constructed with 5 m of rock cover beneath Sydney's Royal Botanic Gardens. Design of rock reinfonnent using a combination of fully grouted rock dowels and Macalloy bars was based on control of horizontal shear movement along bedding features in the roof. A combination of linear arch type analyses and non-linear jointed finite element analyses were used in the design study together with an analysis of the shear resistance offered by fully grouted bolts under shear deformation.

Jan 1, 1993

The mathematical modelling of rock fragmentation by blasting is one of the most difficult and challenging problems of applied mathematics. Not only is complex mathematics required but there is incomplete understanding of the basic physics and chemistry involved. The possibility of getting the physical basis of a model correct by simple mathematical and experimental procedures is demonstrated for the novel process of fragmenting rock by high-pressure arc discharges. While the importance of obtaining the correct physical basis for a model is emphasised, high-pressure arc induced fragmentation of rock is shown to be a powerful laboratory tool for the study of blasting.

Jan 1, 1990