Search Documents

By G J. Zhang

The shape and particle size distribution of caved ore mass in sublevel caving were investigated in this study. The paper first reviews the main factors affecting the shape and characteristic of caved ore mass in sublevel caving and then through the experimental blast testing with cement-sand concrete models, the shape and particle size distribution of caved ore mass were found out. The experimental results indicated that the shape and particle size distribution of caved ore mass was similar to that of the drawn loose body. This finding presented a new perspective for the future study on the ore drawing theory and on the optimisation of structural parameters of sublevel caving. The structural parameters must meet the principle that the shape of the drawn body is in consistency to the shape of caved ore mass.

Jul 11, 2011

For Australian mining projects, sustainable groundwater use is typically defined as a groundwater extraction regime, measured over a specified planning time frame, which allows acceptable levels of stress and protects dependent economic, social and environmental values (DEH, 2004). This principle is compatible with most stakeholdersÆ understanding of our national environmental objectives, yet the application of this policy on a project-specific scale is not always straightforward. Three examples of sustainability issues in the management of groundwater in mining are presented. These examples highlight each of the three dependent values: environmental, economic and social.

Jan 1, 2006

By A T. Spathis, K E. Leslie, K R. Blay

Many open pit mining operations seek to control blasting-related movement of ore and waste to minimise loss and dilution. Tracking the movement of ore boundaries can result in the maximisation of ore recovery and minimisation of waste sent to the mill, thereby optimising the economic performance of the operation.A novel solution for tracking the ore–waste boundary location before and after a blast uses subsurface markers placed along the boundary with all measurements and scans conducted remotely from the blast block. Upon system activation, user-operated equipment on the surface determines the three-dimensional (3D) location of the subsurface markers.The patented system concept combines two electromagnetic mechanisms, magnetic positioning and radio frequency through-rock communications to enable remote battery-powered markers, buried within the rock to be accurately located in 3D space.Field trials at a quarry have demonstrated the system can comfortably handle over 100 subsurface markers with a complete scan, including set-up, taking less than an hour. Location accuracy for each marker in 3D space is better than 0.5 m at a range up to 50 m from the magnetic source, and the system has an overall operational range in excess of 75 m.CITATION:Blay, K R, Spathis, A T and Leslie, K E, 2015. A remote, rapid and accurate three-dimensional ore waste boundary tracking system, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 297–306 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By D Zielinski-Nicolson

The emergence of affordable, portable and versatile wireless devices has enabled a new frontier in mine safety equipment. Existing solutions provide methods for tracking personnel and assets in underground mines but are not designed to optimally integrate into existing and emerging systems. Mine management are often required to coordinate primarily independent emergency, personal protective equipment (PPE), tracking and collision avoidance systems from multiple vendors. These systems involve a variety of wireless technologies that require separate integration projects that discourage adopting new services and policies.

May 5, 2022

By V Rasouli, G Cavanough, A Mokaramian

The sampling time, the costs and its quality are the three factors that determine the best method of drilling in mineral exploration. The two principal methods of reverse circulation (RC) and diamond core drilling are often used in combination by mine operators. RC is used for drilling shallow holes and in-pit grade control, and core drilling for deeper holes to identify future resources. The RC method is faster and more flexible than coring and provides virtually uncontaminated cuttings (ranges from dust to 25 mm chips) to the surface cyclone suitable for geochemical anomalies. The diamond coring produces core samples to increase the level of geological knowledge and the 3D extension and distribution of the orebody. However, both of these methods are subjected to certain limitations and inefficiencies in reaching deeper depths and drilling complex hole geometries. Examples of such shortcomings include the inability to provide enough air pressure for RC drilling and high friction between drill pipe and the hole wall in diamond core drilling.Considering that delivering large volume of reliable samples from deep zones to the surface in shortest possible time is of paramount importance in mineral exploration, and assuming that obtaining core samples over whole overburden is not always essential, then drilling small size holes as fast as possible and delivering the small chip samples to the surface would be a good alternative with several advantages over conventional drilling methods for deep hard rocks mineral exploration. As a result, the use of coiled tube (CT) drilling technology has been proposed recently for such applications. CT is a continuous length of ductile steel or composite tube stored and transported on a large reel; and allows fast drilling by eliminating the connection time and providing continuous circulation during drilling. This enables quick access to the zone of interest to collect the cuttings or obtain core samples. CT is advantageous particularly in drilling directional boreholes and multi-laterals. In this paper, feasibility of using CT delivering reliable samples is discussed for deep mineral exploration. In addition, recent developments and practices are presented that make CT a reliable drilling technology to drill cheaper, faster and deeper and to deliver more continuous and reliable data and samples from deep formations.CITATION:Mokaramian, A, Rasouli, V and Cavanough, G, 2012. Quality sampling using coiled tubing drilling in deep mineral exploration, in Proceedings Sampling 2012 , pp 73-80 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 21, 2012

By D R. Anstey

The mining of magnetite iron ore in Western Australia will generate large volumes of waste rock and tailings over many decades. The need to dispose of these materials will result in massive waste landforms that will require significant planning and management. The formation of comparable man-made landforms is relatively common, as exemplified through past practice in gold and iron ore (haematite) mining. Unfortunately, the performance of these landforms, with respect to long-term stability (erosion resistance), the release of low pH seepage water and aesthetic impact, has commonly been disappointing and environmental legacies have been created as a result. Lessons that have been learnt from past, large mining operations indicate that there is a need to rethink the methods of waste disposal and landform development applied to magnetite mining. The environmental compliance criteria applied to magnetite mines for the storage of tailings and waste typically include minimising dust generation (particularly as the tailings and mine waste may contain asbestiform minerals), control of silt, minimising visual intrusion and management of potentially acid forming materials. In addition, the climate of Western Australia and the paucity of both surface and groundwater in the vicinity of the magnetite mines frequently necessitate water consumption to be minimised. This paper discusses the potential to co-mingle magnetite mining waste streams in a variety of ways to concomitantly satisfy the environmental compliance criteria and the operational requirements of the mine. These methods include co-mingling of coarse tailings and waste through dry-stacking, deposition of tailings as a paste, co-disposing of all wastes to form an integrated landform and the co-mingling of all waste streams to produce PasteRockTM (a blend of tailings paste and crushed waste rock). The paper demonstrates how these techniques can be applied to the magnetite mining industry to provide better outcomes than might be achieved using more conventional techniques, currently employed in large-scale mining operations.

Jan 1, 2009

By Zervoudis J

Limitations of current touch-up solders for galvanised steel include coating thickness control problems and poor corrosion and abrasion resistance as well as health and environmental concerns due to toxic constituents such as lead. This paper reports on progress in ILZRO-sponsored research to develop an improved touch-up solder. Encouraging results were achieved in torch soldering trials with experimental zinc-tin-based alloys. Mouldability and coating thickness control were achieved over a practical working temperature range in which the solders consisted of a viscous mixture of solid primary zinc phase particles in a liquid zinc-tin eutectic matrix. The mouldability was dependent on the microstructure of the solder sticks, and optimum structures could be obtained through control of casting solidification rates and by the addition of small amounts of copper. Hardness, abrasion resistance, adhesion and corrosion tests on experimental Zn- (40 - 50 per cent) Sn-I per cent Cu also showed improved performance over lead-tin-zinc solders and compared the effects of tin content within this range. Atmospheric corrosion testing and optimisation of alloy composition and methods of solder stick production are continuing.

Jan 1, 1993

By J J. L du Plessis, S Viviers, G Ratner

Escalating electricity costs are one of the biggest operational cost drivers in mining. The trend to use high-powered auxiliary fans delivering increased airflow to meet the dilution requirements of diesel equipment, together with the reliance on ducted systems rather than traditional flow-through systems to ventilate areas, increases the overall energy requirements of ventilation systems. To manage and reduce electricity costs energy management systems can be implemented, inefficient operating units can be replaced and the operation of energy-consuming components of ventilation systems can be optimised.This paper describes the process followed to design and develop an energy-efficient axial flow auxiliary fan. The fan-targeted design was based on static pressure and volume flow rate requirements incorporating higher overall fan efficiencies. A brief overview of the results is given, including the aerodynamic design procedure using computational fluid dynamic (CFD) analysis. The mechanical design criteria used, including stress analysis on the rotor and designs to improve the vibration levels of the fan, are also presented. Through this study it was demonstrated that the aerodynamically designed rotors using profiled and twisted blades improve the total fan efficiency considerably when compared with some of the older-generation fans using cambered plates. The latter were typical in the mining sector in South Africa at the time of the study where average overall fan efficiencies of standard cambered fans less than 63 per cent and some of the older-generation cast aluminium blades have peak overall fan efficiencies of about 65 per cent. Peak overall fan efficiency of more than 80 per cent was achieved by using the described design and development process. Additional benefits are that the fans are quieter due to the better aerodynamic design and have a longer operating life due to reduced vibration levels.In conclusion, the use of CFD to develop fans to deliver the required volume flow at the required pressure allows quicker design turnaround time. It furthermore allows the ventilation engineer the option to specify a specific fan and is not limited to an off-the-shelf catalogue fan. It thus allows engineers to purchase a fit-for-purpose energy-efficient fan. The introduction of reliable fan control systems may, however, still result in the biggest cost benefit for underground mines.CITATION:du Plessis, J J L, Ratner, G and Viviers, S, 2015. Design and development of energy-efficient secondary axial flow fans, in Proceedings The Australian Mine Ventilation Conference, pp 337–344 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By D H. Laubscher

The in situ rock mass rating system û IRMR - leading to the mining rock mass rating system - MRMR - for jointed rock masses has been used (and abused) in mining operations around the world for the past 27 years. Despite the recent development of elaborate design procedures and computer-aided design packages, MRMR remains one of the most versatile and practical mine design systems available. It is important to realise that the rock mass classification system should not be replaced but rather complemented by more sophisticated and detailed design procedures. The classification system is not only the æcrudeÆ method used for initial assessment (as described in some geotechnical literature) but also in many respects a very effective and practical engineering tool. MRMR could, and should be used during the entire stage of mine life as an integral part of the design process. The objectives of this paper are to illustrate using practical case histories from the past decade, some of the pitfalls of the MRMR classification system, to clarify certain misconceptions in its application and update its mining application.

Jan 1, 2000

By N Lewis

Recent major urban trunk sewer infrastructure projects in Melbourne have involved construction of nearly 10 km of tunnel boring machine (TBM) driven tunnels in a range of geological conditions varying from soft alluvial soils to hard volcanic rock. To provide both construction and permanent access to the new trunk sewer network, a total of 17 shafts between 5 m and 13 m in diameter, and up to 64 m in depth have been constructed. This paper describes the design and construction of the temporary shaft support systems for the shafts.The range and variability of geological conditions at each shaft site required the adoption of the following shaft support systems across the projects – jet grouting, sheet piles, diaphragm wall, secant pile, contiguous pile, reinforced shotcrete rings and rock bolts.Groundwater control, settlement, TBM launch and reception chambers at the shaft base, chambers and TBM launches at mid-depth of shafts, connection shafts between new and existing sewers and bypass pumping shafts are among the challenges that have been met.This paper reports on the some of the challenges involved and experience gained in developing design and construction solutions for large diameter shafts that are excavated within varying geology in Melbourne over the past three years.

Mar 8, 2011

By R Dunne

"Continuous improvement on metallurgical treatment plants is possible only when good data and analysis of the data are available. Good data implies appropriate and accurate mass measurement coupled with good sampling practices and accurate chemical analysis especially when carrying out monthly metallurgical metal reconciliations. Adequate characterisation of key samples (eg tailings, feed, concentrates and others) at timely intervals is an important part of a good continuous improvement program. The data from this will help identify opportunities to improve operation performance and thus profitability. Examples are provided of projects that have led to improved plant performance based on good metallurgical data collection and analysis.Citation:Dunne, R, 2016. Using Metallurgical Data to Drive Continuous Improvement, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 201–206 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By Y M. Wang, W Z. Liu, L F. Li, X L. Zhang

Based on the blasting crater theory, the equation between k under typical cases and burden line, charge height was obtained by open pit bench blasting analysis model. The model was calculated with mine production blasting. The blastability coefficient k and the best range of blasting burden line were specially emphasised on determination of lateral crater tests.CITATION:Wang, Y M, Liu, W Z, Zhang, X L and Li, L F, 2015. Application of lateral crater test in open pit blasting parameters optimisation, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 463–468 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

The creation of an accurate and precise enough database requires the collection of many representative samples, subsampling and assaying them without destroying their integrity. The selection and implementation of sampling protocols often lead to severe difficulties, making the unaware practitioner vulnerable to massive exploration, feasibility and operating failures. Therefore, there is no substitute for a good understanding of the Theory of Sampling (TOS). Either because of ignorance, or because of short-term economic reasons, failure to comply with many stringent conditions can be devastating for the validity of a feasibility study, leading to false evaluations, to the abandonment of a viable property, or to the exploitation of one that is not profitable. All these failures have something in common: insufficient duplicate sampling, subsampling and assaying were performed; very important, preliminary heterogeneity tests were never performed; for short-term economic reasons, poor sampling and subsampling protocols were selected, second-class sampling systems and weightometers were installed and poor preventive maintenance and cleaning were implemented;and sampling experts were called only when the project was obviously in trouble. The conclusion is clear: in due time, iterative auditing of sampling practices is an insurance policy against massive financial losses for the company involved. A complete, comprehensive 100 point checklist of sampling Quality Assurance and Quality Control is provided, so critically important details to ensure success are not forgotten.

Mar 1, 2010

By L Nagy, K P. Juhasz

The authors were engaged to optimise a traditional rebar cage reinforced concrete segmental lining by means of finite element analysis (FEA) using macro synthetic fibres for the Shanghai metro extension. The aim of this study was to reduce or entirely replace the original steel reinforcement of the segmental lining, in order to make the precast production process faster and more economic. The outer diameter of the tunnel was 6200 mm, the thickness of the segments was 350 mm.The numerical calculations were performed by Atena Finite Element software, which is based on the combination of Menétrey-William and Rankine failure surfaces on the compression and tension sides respectively. The effect of the macro synthetic fibres was modelled as tension stiffening on the tension surface.A one-to-one full scale model of an assembled tunnel ring using the original reinforcement cages was tested at Tongji University in Shanghai, July 2013. The ring was tested to differing load levels where load and displacement were measured until failure. The author’s first step was to calculate the real displacement characteristics of the original reinforced concrete (RC) ring, then calculate the numerically modelled version, so as to compare them. The material parameters of the concrete and rebar used had been determined through basic material tests conducted at the Tongji University. (Bi, Liu and Wang, in press).The numerical modelling undertaken has shown good correlation with the full-scale physical test results. Optimisation of the lining reinforcement was achieved through the addition of fibres, resulting in a substantial reduction of the steel rebar cages. Several results have been computed with the numerical model using different dosages of macro synthetic fibres, showing that the mass of steel reinforcement could be reduced by 50 and 75 per cent respectively.CITATION:Juhasz, K P, Nagy, L and Winterberg, R, 2014. Full-round numerical modelling of a macro synthetic fibre reinforced tunnel boring machine tunnel in the Shanghai Metro extension, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 477–484 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By C D. Pocock

Maintaining catch berm capacity in open pit mines through controlled blasting prevents production delays associated with managing risks associated with wall instability. A method has been developed to quantify the drill hole deviation of presplit holes at Century Mine. Different controlled blasting techniques are used to control wall quality and decrease the risk. The performance of presplit drilling, in terms of deviation from design has been investigated. A methodology has been developed to quantify the drill hole deviation in three dimensions. This methodology was converted into a series of algorithms capable of handling an extensive range of data. The methodology was applied to a case study at Century Mine to evaluate the performance of drilling on two presplit blasts. Overall, 67 drill holes were investigated in the case study. The drill hole deviation was quantified in terms of three parameters: skewness, linearity and drill hole deviation parameter. Methods for quantifying each parameter were developed. Skewness, a measure of the amount of curvature and linearity, was defined as the measure of the consistency of the gradient of the drill hole. Drill hole deviation parameter is defined as the average measured deviation of the surveyed drill hole position from the design position. Acceptable drill hole deviation tolerances for each of the defined parameters were developed by analysing drill hole deviation parameters with respect to implications to catch berm capacity. Verification of the methodology was confirmed through the comparing of the completed drill hole deviation results using both visual inspection and cross analysis for each of the three methods. Holes with an R squared value of less than 0.97 for skewed deviation were classified as having skewed deviation, while holes with a difference in gradient of 3.5 were classified as having linear deviation. The results show that 76 per cent of the drill holes had deviation. Of this, 19 per cent were skewed, 57 per cent had linearity and 12 per cent contained both skewed and linearity deviation.

Nov 8, 2011

By J P. van Dyk

A new crude ilmenite beneficiation process was recently proposed that allowed for the preparation of a smelter grade ilmenite from ilmenite with elevated chromium content. Magnetising roasting was not utilised in the process. As part of this circuit an ilmenite low susceptible reject stream was produced that had a low magnetic susceptibility. In this article a magnetising roasting process was investigated to beneficiate this material. Tests were conducted on material produced by pilot scale simulations on a typical South African East Coast heavy mineral reserve. The results obtained were compared to those published in literature for crude ilmenite. The small-scale experiments were used to define approximate operational limits for the oxidising roasting of a low susceptible ilmenite low susceptible reject stream, although industrial roasting conditions may differ significantly from those obtained in laboratory units. In a next phase these results will be confirmed on pilot plant scale.

Jan 1, 2001

By A Liu, X Wang, W Peng, Q Zhang

Pulp rheology plays a critical role in fine mineral flotation. Yield stress and apparent viscosity are two important rheological parameters affecting mineral flotation recovery. In this paper, the concept of pulp rheology and its measuring method are presented. The main factors, such as particle size, pulp concentration, mineral types, pulp temperature, inorganic salts, that affect the pulp rheology are systematically reviewed, and then followed by the discussion of the relationship between pulp rheological properties and flotation performance. Generally, high pulp apparent viscosity and yield stress values have been found to have an adverse effect on flotation recovery. In addition, due to the hetero-coagulation between the valuable mineral and gangue mineral, the pulp of mixed ore shows higher viscosity than that of the single mineral slurry. This paper is expected to provide some references for the efficient upgrading of low-grade and complex ores from the perspective of pulp rheology.

Aug 24, 2022

By Howes PM

In the iron and steelmaking processes, dusts are generated and treated by wet dedust- ing methods to form slurries which are high in iron content, but also contain certain impuri- ties. For many years these slurries have been processed and the wet cake, which is produced, has been dumped because of the high zinc and alkali chloride contents. Sintering is an appropriate process for recycling of these materials, provided the deleterious impurities can be kept under control. Zinc is a deleterious element in blast furnaces because it promotes the formation of accretions on the upper walls of the furnace. This results in irregular furnace performance. Alkali chlorides effect the emissions from the sinter plant waste gas due to the high resis- tivity of these components, resulting in decreased efficiency of the electrostatic precipitator. Experimental work indicated a concentra- tion of zinc in the -11 pmt particle size frac- tion. A cyclone plant was installed producing a "coarse" usable product and a "fine" waste Product.

Jan 1, 1984

This paper briefly reviews the background of mobile primary crushers and their current main areas of application. The benefits of applying mobile primary crushing and belt conveying systems are analysed. The impacts of applying such systems to different steps of the mine process are discussed, including mine development and planning. Application examples are used for demonstrating further possibilities to apply mobile primary crushing and belt conveying systems in mining projects successfully.

Jan 1, 2007

Project delivery in our current market is not as efficient as it could be. Industry at large (both client and consultant), is diligently following the engineer, procure, construct, manage (EPCM) or engineer, procure, construct (EPC) delivery models and not necessarily appreciating the underlying principles that make them the effective tools they were to start with. We often misinterpret project management with EPCM and end up with a literal and superficial interpretation instead of the disciplined risk reduction and business value capture exercise it is intended to be. One of these underlying principles is the project team as resource or commodity depending on which perspective we follow. Some of us understand this principle only too well and succumb to the temptation to take advantage of the imbalance in the understanding of EPCM by selling bodies and hours. Value and return on investment do not always come into the equation. The latecomers and aspirants are struggling with this as a barrier of entry into this lucrative market, since as we all know - people as commodity was becoming and still is a scarce resource. Clients are also waking up and asking why 1000 engineers on the floor are better than 100, when engineering design in all aspects of industry, new technology aside, is mature. Why is it that we start with a clean sheet of paper with every project or that neighbours in the same industry segment and location just happen to have completely unique conditions and circumstances that require totally original design (Local conditions aside)? The answers to this question appear when we explore the role of the project team and how it is structured. We will need to investigate team culture and levers for success. Then we will formulate a business case for a team to be able to follow traditional project management practices with EPCM delivery models but yet end up with an alternative look, feel and result. An outcome where more input is not necessarily better and the client and consultant both are aligned with success measured in dollars and a win-win outcome for both parties.

Jan 1, 2009