Search Documents

Vertical flow systems (SAPS, vertical flow wetlands) are increasingly used for passive treatment of mine drainage that is net acid. Data on 30 systems in eastern US show that well designed systems typically add about 40 g/d/m2 of alkalinity to influent net acid water. If they are designed with a conservative loading rate of 25 g/d/m2 and carefully constructed, they produce net alkaline water. Alkalinity added depends on influent acidity, Fe, pH, and retention time, and ranges widely, from 7 to 484 mg/L, so this is not a useful design criterion. Some waters may benefit from retention times longer than the conventional 12 - 16 hours, but the design must be partly based on cost-benefit considerations. Systems with fine limestone added to the compost layer perform better than average, perhaps to an alkalinity generation rate of 80 g/m2/d. A variety of problems are noted in the 30 systems and others reported in the literature. Systems with high influent Fe (> ~75 mg/L, varying with pH) tend to gradually decrease in flow rate because of precipitation and settling of Fe hydroxides on top of the compost layer. Some high-Fe systems precipitate Fe in the limestone layer, suggesting inadequate compost thickness, or short-circuiting through thin spots. Systems with Al exceeding about 10 mg/L tend to plug because of Al hydroxide precipitation in the limestone layer. Flushing only removes a small part of this precipitate, but can extend life. Some systems are ineffective because of failure of the inflow system. Some systems are uneconomic because they are oversized. A continuing program of inspection and maintenance is necessary for long-term performance.

Jan 1, 2003

By Mules GJ

Geotechnical investigations have played a key role in influencing decisions for development of the Porgera Gold Project in the highlands of Papua New Guinea. Porgera is located 130 km west-northwest of Mt. Hagen in steep mountainous terrain with high rainfall. Much of the site is underlain by weak mudstone of the Chim Formation and creeping colluvial soils. Landsliding is common on the steeper slopes and in the valley floors. Structures have had to be sited to avoid areas susceptible to these movements. Early stage feasibility investigations included studies of tailings dam and waste rock dump sites, processing plant sites and hydroelectriic schemes. Further studies, leading into the design stage included the Enga Highway upgrading, water supply and power supply schemes. As construction for the project proceeds geotechnical input remains at a high level, with emphasis now on maintaining viable stable sites and refining data on which designs were based.

Jan 1, 1990

The Gj0vik Olympic Mountain Hall is the world's largest underground cavern for public use and was created primarily to facilitate the ice hockey tournaments for the 1994 winter Olympics in Norway. The cavern has a span of 61 m, is 91 m long and is 25 m high. Ordinarily, rock caverns have a span width of 15 to 25 m, however, temporary mining caverns of up to 60 m have been excavated and natural caves with even greater dimensions occur. The Gj0vik Olympic Mountain Hall is unique as it is for public use with a capacity for 5800 spectators. Blasting was conducted with a high production rate at normal costs due to detailed planning and strict supervision of each round. The initiation system and vibration monitors were the main tools to control vibration levels and to facilitate a high production rate. It was of utmost importance that the rock remaining in the roofs and walls was of high quality after blasting to avoid rock fall, rock slides and excessive maintenance work.

Jan 1, 1995

The discovery of nickel sulphide deposits at Kambalda in 1966 heralded the development of ò an industry with a capital value of over $1.5 billion producing about 10% of the western world's nickel. ò an unprecedented exploration boom in which over $200 mil- lion was expended in 10 years in the search for nickel deposits. ò a major new class of nickel deposits stimulating exploration for similar deposits overseas. and rapidly propelled a struggling small mining and exploration company to become one of Australia's corporate giants, provid- ing a much-needed stimulus to economic activity in a region suffering from a severe downturn in its principal industry, gold mining. Production of nickel in Western Australia commenced at Kam- balda in 1967 and grew rapidly to a rate of over 30,000 t of con- tained nickel per annum in 1970, 40,000 t in 1973 and 50,000 t in 1975. Early production was aided by a shortage of nickel on the world market due to disruption of supply from the major Canadian producers, resulting in high free market prices for the metal. Since these early years, the industry has experienced a number of cycles of indifferent health due principally to market developments overseas, although the level of production of nickel in Western Australia remained fairly consistent. The two most serious of these, in 1977-8 and 1985-6, forced the closure of a number of mines. Current nickel prices are allowing remaining producers to enjoy a measure of relative prosperity, although there is little general speculation that this will be long-lived. Nickel deposits discovered in the exploration boom were almost exclusively related to ultramafic rocks. Volcanic peridotite (komatiite)-associated deposits, exemplified by the Kambalda ore- bodies, were the targets of initial exploration which was concen- trated on ultramafic sequences near lower stratigraphic contacts with underlying mafic rocks. Subsequently, discoveries made in coarse-grained dunites in interpreted intrusive settings broadened the search parameters.

Jan 1, 1988

By G R. Hancock, W D. D P Welivitiya

is placed in a waste rock dump, which is usually later reshaped to be erosionally stable, initiate and sustain vegetation and ultimately integrate with the surrounding undisturbed landscape. However, it is unclear how this exhumed material will weather and evolve for most sites. Also, there is a lack of data on the weathering of post-mining materials. If weathering is better understood, then there is the potential to improve rehabilitation outcomes. To improve predictions of the evolution of soil properties and weathering-limited erosion, estimating the rate at which fine, transportable material is produced from the weathering of larger, non-transportable particles and the resultant fragment size distribution and how that distribution evolves over time is necessary. This study examines the weathering process for four different coalmine waste rock materials for a Bowen Basin, Queensland site. Materials obtained from various areas of the coalmine were subjected to cyclic wetting and drying and heating and cooling. Particle size distribution and other material properties were explored after each experimental cycle to ascertain how the material changes during the experimental cycles. The particle size distribution data of wet and dry cycles were used as input data in a numerical weathering model to explore the dynamics of the weathering process for each material sample. A Monte Carlo framework was employed to assess the geometry of the weathering products, weathering rate and the number of daughter particles produced within a weathering cycle. Then the SSSPAM Landscape Evolution Model was used to evaluate the influence of weathering on erosion and landscape evolution of a post mining landform. SSSPAM simulations with: (i) active weathering and (ii) without weathering were run for each material. The erosion rate and the overall landform structure were then compared between weathering and non-weathering simulations.

Aug 2, 2023

The Pike River Coalfield is located on the West Coast of the South Island of New Zealand near the top of the Paparoa Range approximately 45 km north east of the coastal town of Greymouth. The Pike River Coal Company Ltd (PRCC) is owned jointly by New Zealand Oil & Gas Limited (NZOG) and private investors.   The project has followed a long and difficult road towards project implementation which is now a reality with mine construction scheduled to commence in November 2005. The first stage of the project, the consent and land access process has been the most difficult. Resource consents for the project were first applied for, granted and appealed in 1998. A second round of modified resources consents followed a similar path in 2001. Following consultation with a range of parties including local and central government as well as the Department of Conservation, in March 2004 the Minister of Conservation granted PRCC access through Department of Conservation land. In October 2004, the Environment Court issued a Memorandum of Consent granting resource consents with conditions that had been negotiated between PRCC and the appellants.   The second stage of the project, investigation and design, commenced in December 2004 and was completed in June 2005 with the PRCC board ratifying the project capital and operating budgets. While the investigation and design work was proceeding, PRCC were also engaged in securing private equity and bank debt funding for the project. Formal Board approval to proceed with project construction was granted in September 2005 following completion of fund raising.   The project consists of a number of significant construction activities, namely: +        10.5 km of mine access road through previous logged and virgin rain forest; +        2.2 km of tunnel through metamorphic rock; +        a coal preparation plant about 8.3 km from the mine portal; +        an underground coal preparation plant; and +        a major slurry pump station, high and low pressure underground water supply systems to support hydraulic mining units and underground coal transport respectively.   Project construction is expected to be completed in April 2007 with completion of the ventilation shaft. Mine production will commence in December 2006 with coal from pit bottom development which will be carried out by the mine owner.

Jan 1, 2005

By M Edgar, G Pattemore, M Auad, K Job, A Job, S Gale

In recent decades, significant advances have improved the modelling techniques for predicting slope failure. Predicting failures is vital in open pit mining due to the significant risk posed to personnel and equipment from unstable pit walls. Failures not only cause harm and damage to people and equipment but also cause delays to production and subsequently increase operational costs. Coupled with improvements in modelling techniques, utilisation of advanced scanning systems, such as high-definition imagery from UAVs has enabled faster and more precise mapping and modelling. However, one key element required for accurate slope stability modelling and monitoring is the ability for mine geotechnical engineers to have an accurate understanding of the mineralogy and moisture content of slopes, in real-time. To address this challenge, research has been undertaken to utilise hyperspectral imaging across a broad spectrum, combined with high-definition imagery, and LiDAR to scan slopes for minerals and moisture content. In addition to accurately mapping mineralogy and moisture, the data must be collected autonomously and remotely to ensure ongoing safety. The results show that there are many direct and indirect benefits from this new technology, including the ability to monitor slopes at a safe distance and in real-time, improved accuracy of modelling, detection of risks, and improving the automation workflow for geotechnical engineers. The paper presents recommendations for the implementation of the technology in open cut mining environments.

Jun 22, 2022

By E T. Baker, J A. Resing, S L. Walker, V Ferrini, F Martinez, R Haymon

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Enumerating active sea floor hydrothermal sites has been a challenge since their discovery almost 40 years ago. High-temperature hydrothermal sites are readily discoverable, primarily by detecting mineral-laden plumes, but working at these sites poses severe environmental and operational difficulties. Low-temperature vent fields, which may represent waning of venting from high-temperature systems, may be more accessible but are more difficult to locate. Over the last decade, however, oxidation-reduction potential (ORP; aka Eh) sensors capable of detecting minute concentrations of reduced hydrothermal chemicals have been successfully used to pinpoint such fields. In this extended abstract, we use ORP anomalies observed during continuous (towed sensor) plume surveys to estimate site frequency along four intermediate- to fast-spreading ridge sections. From these data, we estimate site frequencies between five and 16/100 km for these ridge sections. Previous camera surveys on the fast-spreading East Pacific Rise support these frequencies. These rates are much greater than the frequency of ~0.5–5/100 km, generally increasing with spreading rate, derived from well-surveyed ridge sections in the InterRidge database (InterRidge, 2014). The higher frequencies arise because ORP sensors are able to distinguish between sites as close as ~1 km and identify sites with negligible or no optical plume signal.CITATION:Baker, E T, Resing, J A, Martinez, F, Haymon, R, Walker, S L and Ferrini, V, 2015. How leaky are oceanic ridge axes? A new assessment of the spatial density of submarine hydrothermal discharge, in Proceedings PACRIM 2015 Congress, pp 3–8 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By S L. Simpson, J Waworuntu, B M. Angel

"The Batu Hijau copper/gold mine, operated by PT Newmont Nusa Tenggara, is located in the south-western part of Sumbawa Island, Indonesia, and is situated ~10 km from the south coast at an altitude of ~450 m above sea level. The mine became fully operational by year 2000 and processes approximately 120 000 t of ore per day that contain an average of 0.53 per cent copper and 0.4 per tonne (g/t) gold. Tailings management at the mine includes a deep-sea tailings placement (DSTP) system that discharges tailings through a pipeline via an outfall located at a depth of 125 m at the head of the submarine Senunu Canyon (Figure 1).The environmental impact assessment undertaken prior to approval of the DSTP evaluated both on-land tailings storage facility (TSF) and DSTP options for tailings management. Negative attributes of the on-land TSF included removal of approximately 2300 ha of forest/agricultural land, the potential relocation of >2000 people from their communities, the high average annual rainfall (>2500 mm) and potential for earthquakes presenting challenges for water management and creating a long-term risk of failure. The final choice and Indonesian Government’s approval of DSTP was also influenced by the close proximity of the deep submarine canyon to the mine. The Batu Hijau mine is one of the larger examples of DSTP in the world and deposits tailings at the greatest depth. The depth of the main canyon increases to >2000 m within 20 km of the coast, and to >3000 m approximately 50 km from the coast.The DTSP at Batu Hijau must comply with an environment management plan (EMP) and environment monitoring plan of permit stipulation that approved its commencement in 2000; updated in 2010 and 2015. The environmental management objectives were to avoid impacts to highly productive components of the ecosystem such as coral reefs, mangroves, surface waters and fisheries, and confinement of impacts to areas of low biological productivity. In the vicinity of the DSTP outfall and within the Senunu Canyon, the management plan predicted significant adverse impacts from the DSTP on the marine ecosystem in the form of: reduction in sea water quality due to elevated turbidity and dissolved copper concentrations burial of benthic organisms a reduced habitat for demersal fish.Recovery of the pelagic and benthic ecosystem to preoperating conditions was predicted to occur within the first two years after operations cease. The CSIRO has performed due diligence studies to independently verify compliance with permits and evaluate new monitoring objectives (Apte et al, 2004; Simpson et al, 2010; Angel et al, 2015), and has performed assessments of environmental monitoring data on the tailings footprint and ore stockpile processing against the above environmental objectives (Simpson and Angel, 2015).CITATION:Angel, B M, Simpson, S L and Waworuntu, J, 2016. Long-term monitoring and targeted assessments to improve management of mine wastes – the Batu Hijau project, in Proceedings Life-of-Mine 2016 Conference, pp 81–84 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 28, 2016

Responsibility for the administration of mineral resources is divided between federal and provincial governments. The paper traces the evolution of mineral policies at both levels of government, from the end of World War II to the present. In the immediate post-World War II years, the emphasis was on supplying the raw material needs of a rapidly growing world economy. Policies favouring growth and development of the Canadian mining industry were instituted during this period. Two decades of uninterrupted expansion (the 1950s and 1960s) ensued. The decade of the 1970s was a turbulent one for Canadian mineral producers. Governments intervened more substantially than ever before. Moreover, the industry suffered from an intense period of competition for resource revenues by the two levels of government. At the same time, far reaching changes were taking place in the structure of world mineral markets. To date in the 1980s, the mineral industry has, perforce, adapted to existing mineral market structures. Mineral policies, too, have shown signs of adapting to the needs of the mineral industry. Whether the resulting mix of policies will permit the revitalization of the Canadian mining sector remains to be seen.

Jan 1, 1986

Experimentation with new methods, materials and machines to improve primary drilling and blasting is a continuing practice in the hard rock quarry operations of the BMI Group. These experiments will continue in the remote hope that one day we may produce a perfect feed for the primary crusher. As this day is still a long way off, the necessity to break oversize boulders will be a problem to be faced for the foreseeable future. To gauge the efficiency of primary blasting from this point of view, BMI monitor the tonnes of material crushed in the primary crusher for each boulder requiring secondary breaking. Over a period of about 10 years, this figure has improved from 30 tonnes througi the primary crusher per boulder, to 100 tonnes per boulder at our largest operation, which produces in excess of 2 million tonnes per year. Evan with this improvement, 25,000 boulders require secondary breaking each year This paper does not provide the solution to this problem, as like primary blasting, it will have to be constantly reviewed as new products and techniques become available. The paper sets out all of the methods tested or considered for test by BMI and our nnnn1iicinnq nn Chair PffPr.tivPness . Economic

Jan 1, 1978

By J Q. Cooper

The New Zealand rail authority, Kiwi Rail and Auckland Regional Transport Authority (ARTA), are jointly planning a new mainline rail link between Auckland’s downtown Britomart Station and the existing Western Line at Mt Eden. In 2009, APB&B, a consortia of Aecom, Beca, Parsons Brinkerhoff and Hassell Architects where commissioned to develop the conceptual design, Assessment of Environmental Effects (AEE) and business case for the new 3 km rail line towards preparing a Notice of Requirement to protect the route through Auckland’s central business district.This paper describes the engineering challenges in the development of the conceptual design for the three proposed underground stations, the running tunnels and connections to the existing network. Feasible alignment and station location options were developed and evaluated using multi-criteria analysis based on key client functional requirements, constraint mapping and environmental impacts. The resulting preferred scheme was then developed to a conceptual design suffi cient for assessment of environmental effects, risks, and the development of a robust construction methodology to allow high level capital cost estimates.The paper describes some of the major challenges overcome to develop the concept, including steep gradients, narrow street envelopes with existing buildings and structures, the need for large platform spaces with low ECBF rock cover and complex connections at Britomart and the main line near Mt Eden.The development of the conceptual design of the underground stations in particular demonstrates the need for a holistic value engineering approach to satisfying the architectural and functional requirements, in a highly constrained dense urban environment and at lowest practical cost. The construction methodology was a key input to the conceptual design development throughout.The conceptual design will be used as the fundamental basis for the development of the AEE and business case for the project in the future.

Mar 8, 2011

By W Roy

When it comes to plan implementation and securing success in organisations in the 21st century, if there was such a thing as the secret to success it would be effective communication. Commoditisation brings financial, operational and cultural advantages to organisations that use effective communication. Effective communication tools turn æpeople problemsÆ into system control solutions, removing personality clashes that hide procedural malfunctions. By introducing communications frameworks available in the market place today, and case studies of their use, this paper provides insights into the successes available to organisations courageous enough to redefine their communications for the 21st century.

Jan 1, 2006

By L Abrahamsson

The aim with this paper is to discuss experiences from the ongoing research project ‘Attract: A roadmap to attractive, inclusive, and safe mining workplaces’. The project’s aim is to analyse possibilities, effects, and consequences of the green and digital transformation in the Swedish mining industry from workplace, socio-technical and gender equality perspectives. The research project (2022–2025) at Human Work Science at Luleå University of Technology is financed by the strategic innovation program Swedish Mining Innovation (a joint venture by the national research funds Vinnova, Formas and the Swedish Energy Agency). The project includes a multidisciplinary research group of five senior researchers and five PhDstudents and a broad repertoire of methods, eg literature reviews, qualitative interviews with both managers and workers, workplace observations, workshops, surveys, and project seminars where the researchers and the company representatives together analyse the results. One important part of the project is the applied approach where the researchers work together with two mining companies and one subcontractor company. The project has two parallel main subprojects.

Sep 1, 2024

By J J. Jiang, B G. Bow

Atlas Iron Limited’s (Atlas) Abydos Mine has developed its Scarborough open pit proximal to a rock shelter that has been assessed as a significant Aboriginal heritage site by the Traditional Owners of the land. The rock shelter, named Yurlu Kankala, is located to the north-west of the pit with a stand-off distance of 35 m. Within Atlas’ Native Title Agreement with the Traditional Owners, and approvals from the Western Australian Department of Aboriginal Affairs, commitments have been made to conduct mining in a way that avoids or at least minimises disturbance and damage to the rock shelter. This complies with the Aboriginal Heritage Act 1972 (WA) and respects the heritage and culture of the Traditional Owners.CITATION:Bow, B G and Jiang, J J, 2018. Iron ore mining in proximity to a significant Aboriginal heritage rock shelter, Pilbara Region, Western Australia, in Proceedings Life-of-Mine 2018, pp 2–5 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By S R. Green, G D. Corder

The legacy issues from mining can, and have often, extended well beyond the closure of operations. However, conventional cost-benefit analysis provides little incentive to implement initiatives at the project development stages of a new mining project as the costs that will be incurred towards the end of the mine life, 20 years or longer, appear minor in net present value (NPV) terms. This analysis can be misleading as the true costs of managing post-mining land can continue for many years, or decades, after mining ceases and any resulting unfavourable legacy issues can delay or prevent government permits or licences to develop new resources. Proper upfront planning is critical for implementing successful rehabilitation and closure strategies. The investment in this planning needs to be done in a structured and rigorous manner taking into consideration the long-term and broad benefits of sustainable land uses after mine closure. The advantages of such an approach could include the streamlining of regulatory approvals by early advice to the regulator of identified issues and responses to those issues, and clear evidence that a strong social licence to operate ethic with local, regional and national benefits is included in the decision-making process. This paper investigates the potential closure options for two case studies at the early stages of project development - concept and prefeasibility. By using a sustainability framework that can identify opportunities and risks, prospective initiatives that deliver enhanced environmental, community and social benefits will be compared with compliance-orientated approaches. This comparison is made across the Five Capitals Sustainability Model - natural, human, social, manufactured and financial. The results of this analysis demonstrate that upfront planning during project development and due care and effort during the life of the working mine will reduce the risks of long-term detrimental legacy issues. This will ultimately benefit the mine operator, the local community and the state.CITATION:Corder, G D and Green, S R, 2012. Using a sustainability assessment framework to achieve enhanced legacy outcomes, in Proceedings Life-of-Mine 2012 , pp 311-318 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

The chief use of manganese ore is in the production of ferromanganese alloys for steelmaking. Manganese ores generally occur in tropical areas, which influences the type of treatment required. Present methods of treatment are relatively unsophist- icated but demands by customers for tighter specifications will necessitate the installation of gravity concentrator at many mines At present only limited tonnages of minus j in. product can be sold hence future development will centre around methods of producing an agglomerate satisfactory to the smelter.

Jan 1, 1969

The Carnilya Hill Mine, a joint venture project between Western Mining Corporation Limited (WMC) and The Broken Hill Proprietary Company (BHP), is a nickel sulphide deposit being developed by the Kambalda Nickel Operations (KNO) of Western Mining Corporation. Seven months elapsed from the time a decision to proceed with the project was taken until the first ore production. During the first month of operation a new KNO record for decline development was set. Equipment used includes an electro- hydraulic drill jumbo, 4 cubic metre front end loaders, and 35 tonne haulage trucks.

Jan 1, 1981

By Haeussler P, Christie A, Bradley D, Skinner D

Mesothermal gold deposits of southern Alaska and Westland, New Zealand have both formed at the seaward edge of major collisional zones in the Pacific basin. In Alaska, production of large fluid volumes correlates in time with the addition of heat into the lower parts of the accreted terranes in the late stages of collisional orogeny. This heat was critical for driving both the metamorphic reactions that released the large volumes of fluid that carried the gold, and the contemporaneous widespread anatexis and magmatism. In Alaska's Chugach terrane, this heat was produced by subduction of a spreading ridge beneath the North America continental margin in the Eocene. The resulting products were the S-type granites and gold-bearing veins. The similar widespread S-type plutonism and gold veining in Westland's Buller terrane suggest that a similar tectonic event could have triggered ore formation along the southeastern edge of Gondwanaland. Based on the Alaskan model, a Devonian or Early Carboniferous age is favoured for high volume metamorphogenic fluid generation and gold vein formation in Westland.

Jan 1, 1995

By E Nunes, R Mendes, D Jacobson, G Cota, T Machado, E Santos, J Almeida, E Pereira9, B Raso

Grinding circuits are known to be the highest consumer of energy used in the ore comminution process, with high operational costs and sensitivity to ore conditions. The mining industry is being encouraged to look for more energy efficient processes while increasing the mass and metallurgical recovery; a specific example is projects with lower iron ore grades, which demands a higher level of liberation and resulting higher energy consumption. This has led to increased usage of high-pressure grinding roll (HPGR) technology as an alternative design within the comminution circuit. A growing use of the HRC™ HPGR technology has been used to generate concentrate through a more sustainable process. In the Brazilian state of Minas Gerais, the readaptation of iron ore beneficiation circuits has been initiated, replacing the traditional crushing-to-grinding flow sheet with circuits using crushing-to-HPGR flow sheets, with the main driver being reduced energy consumption. Utilising results from sampling campaigns and analysis of experimental data collected in an industrial plant, the work herein presents a case study from the JMN Mineração operating plant, where the HRC™ HPGR was used as an alternative to traditional grinding using horizontal mills. The results show that the HRC™ HPGR performance in this iron ore processing plant showed benefits in terms of reduced energy consumption as compared to the projected performance with a traditional grinding circuit.

Sep 18, 2023