Search Documents

Sampling of CIL/CIP circuits is typically done by compositing samples of feed and tails over eight or 12 hour periods. As the residence time in the leaching tankage may be approximately 20 hours, the tails from any period being derived from material entering the circuit 20 hours earlier do not correspond to the head from the same sampling period. Moreover, mixing in the series of tanks in a circuit also modifies correspondence between input and output. A special purpose simulator has therefore been developed to allow for the mixing and delay in the tankage and permit estimation of the head assays corresponding to any tailings sample. Thus more accurate assessment of the day-to-day recoveries of gold and silver follows. The model, programmed in Excel, assumes that the tanks are perfect mixers. By inputting the sequential head grades and considering that no leaching has occurred, the head grade which corresponded to the tailings for each period could be estimated. Allowance is made for variations in feed rate over the sampling period by computing the average flow rate of slurry and thus the residence time of each increment of the tailings. This simple model and its application have been found to be subject to some limitations, which are discussed in the paper, resulting in some unresolved variability in results. However, for a typical circuit even the simple model was able to greatly improve consistency of recovery data with variations being approximately halved by eliminating much of the anomalous variation arising from the lack of correspondence between head and tail when changes in head grade are occurring. Therefore, this permits genuine variations in metallurgy to be identified with greater confidence and thus operational shortcomings can be identified and addressed more quickly.

Jan 1, 2006

The mining of Australia's rich and diverse mineral resources has been central to the development of the continent by "Europeans" over the past two hundred years. Mining has historically been encouraged (to varying degrees) by development-orientated state governments (the. managers of largely Crown-owned resources) and since Federation, by successive Com- monwealth governments (which have seen mineral development as a means of generating export revenue to fund predominantly social-welfare orien- tated budgets). This marriage of convenience between governments and the mining industry has to date served all parties well. However, Australia's entry to a new world economic environment at a time that community percep- tions are changing (owing to an education-inspired challenge to "old" values) is challenging the hitherto held assumption that mining develop- ment is always aligned with the well-being of the State and community. Issues such as the type and extent of State/Commonwealth government taxation, resource ownership and control, the environment, land use con- flict, the extent and desirability of secondary processing and infrastruc- ture funding are being debated in the public arena. Opponents of mining in the community are well-organised and are well funded, articulate and more importantly, they have effective communication channels with most governments, irrespective of political complexion. Apart from some television-orientated corporate image building and recent efforts by AMIC, the industry's response to this challenge has been unco-ordinated, poorly directed and arguably ineffective. Professionals working in the industry are concerned about the community's perception of themselves and their industry. Recognizing that the Australian democratic system ensures that, in the large, government at its various levels, is reflective of and responsive to the views and aspirations of people, the industry's response must be wide- ranging, equally articulate and couched in a form which is politically acceptable. New objectives in providing information to the public and its educators must be formulated. Moreover, professionals are looking for new directions from industry leaders. The Institute is well placed to facilitate this process.

Jan 1, 1988

By S Basu, S L. A Gowravaram

CaF2 has been a common constituent in a wide variety of welding fluxes, including those used for submerged arc welding (SAW). The widespread use of CaF2 stems from its role in lowering the liquidus temperature as well as the viscosity of the molten slag that covers the weld pool. However, the harmful effect of fluoride evaporation from molten flux, on the environment as well as the health of the users is becoming increasingly evident over the years. This has led to increasing attention towards reducing the CaF2 concentration in the fluxes. The fluoride-free formulations face the challenging requirement to maintain the thermo-physical properties (viscosity, liquidus temperature etc) like those observed in fluoride-containing fluxes. In the present work, three fluxes with compositions in the CaO-MnO-SiO2-Al2O3 system have been identified as promising alternatives to the CaF2-rich fluxes. However, the thermo-physical properties of any such flux need to be comparable to CaF2-based commercial SAW fluxes before it can be adopted for regular use. The single hot thermocouple technique (SHTT) has been used by several researchers in the past as a tool for observing the melting and solidification characteristics of fluxes. This device has been developed in the present work and is used to characterise the melting behaviour of the fluxes. The measured solidus and liquidus temperatures from SHTT were compared with the results from differential thermal analysis (DTA) and simulations using the FactSage™ software for a comprehensive understanding. In spite of having a slight deviation in the measured values from the multiple techniques, the results obtained from these multiple methods show that the selected compositions could be potential CaF2 free alternative welding fluxes.

Jun 19, 2024

By L L. Kuhar

The AMIRA International P843A Geometallurgical Mapping and Mine Modelling (GeMIII) project is an interdisciplinary research collaboration between 17 global mineral companies and four research organisations aimed at providing support for the emerging industry trend of geometallurgy. The main aim of the project is to develop predictive geometallurgical indices which can be incorporated into a resource block model to maximise the commercial value of an orebody and to minimise the social and environmental impact of mining operations.Researchers at the Parker Centre/CSIRO have been focusing on the development of predictive hydrometallurgical indices for the GeMIII project via rapid, small-scale, cost-effective tests and protocols for comparative ranking of attributes relevant to leach performance. The focus of the small-scale leach tests has been to determine the leach index (relative indication of leach performance), recovery, impurity deportment, reagent consumption, effect of size/degree of liberation and mineralogy of samples for their relative ranking. Predictive tests for heap leach hydrology (related to agglomerate characteristics) and slurry rheological behaviour are also being developed.

Sep 5, 2011

By J C. Small

Time-dependent deformation occurs when geo-materials are under an applied load; this may lead to additional deflection of a tunnel structure and the stress redistribution in the surrounding rock, shotcrete lining and rock bolt support system over time. A better understanding of this creep behaviour can improve the reliability of design, construction and maintenance of tunnels. Hence, the present investigation was carried out on the time-dependent properties of rock, shotcrete and the combined tunnel support system. Tunnels constructed in different ground conditions were modelled. The closure changes of the tunnel with time and the redistribution of stress in the surrounding rock, shotcrete lining and rock bolts due to the creep deformation were analysed. Results of the present analysis were compared with the results from the commercial program ABAQUS.

Jan 1, 2008

By M Zoorabadi, B Hebblewhite, S Saydam, W Timms

Based on the cubic law, the hydraulic aperture of rock discontinuities has the most significant effect on the hydraulic conductivity of jointed rocks. The hydraulic aperture of rock discontinuities is a stress-dependant parameter and reduces with increasing applied stress. Furthermore, the rock stress increases with increasing depth. Therefore, hydraulic aperture is a depth-dependant parameter. In this paper, new empirical equations are introduced to calculate the hydraulic aperture of rock discontinuities at different depths. These equations were developed on the basis of back analysis of compiled packer tests from different actual cases. They provide the capability to calculate range of variation and average hydraulic aperture when the orientation of discontinuity and field stress tensor are given. Furthermore, it is possible to calculate the hydraulic aperture of rock discontinuities when its value is given for another depth. A hydraulic aperture of 7.7?µm was calculated by this method, comparing well with a reported site value of 8.3?µm for rock discontinuities at the Stripa mine project at a depth of 385?m. These new equations can be used by analytical or numerical methods to estimate the hydraulic conductivity of jointed rocks.CITATION:Zoorabadi, M, Saydam, S, Timms, W and Hebblewhite, B, 2014. New empirical equations to estimate the hydraulic aperture of rock discontinuities at different depths, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 375–380 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By A Patwardhan, M M. Alam, K K. Thatavar

A commercial wet scrubber was used in the SIU-Joy dust control laboratory to test several concepts for improving the dust control efficiency of a wet scrubber. The concepts tested included two filter-two-spray systems, hollow and full-cone sprays, horizontal and vertical sprays, different layer filters and addition of surfactant. The optimised scrubber configuration had water-only vertical sprays for pre-wetting coarse dust, and vertical surfactant-laden water sprays for wetting ultrafine particles. This scrubber configuration reduced dust concentrations from 250 mg/m3 to 1.8 mg/m3. In comparison, the conventional scrubber configuration in the feed provides an outlet dust concentration of 3 - 4 mg/m3 in field operation. Upon successful testing and optimisation of parameters in the laboratory, field demonstration of the concepts was conducted at an Illinois coal mine. The optimised scrubber configuration was tested in the field with good results in terms of improved visibility in the face area and reduced respirable and quartz dust concentrations. Additional modifications in the field involved relocation of the scrubber suction inlets from the bottom to the side and changing the water spray configuration on the miner head. These additional changes were based on a conceptualised spatial dust distribution profile in the face area. The results of these laboratory development and field demonstration studies are presented in this paper.

Jan 1, 2005

Expert systems are a product of Artificial Intelligence (AI), a field of long standing, dedicated to the study of problem solving using heuristics, construction of symbolic representations of knowledge about the world, communications proce

Jan 1, 1998

By G Bignall, I Chambefort, A B. Christie, A J. Rae, M P. Simpson

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Key indicator hydrothermal alteration minerals formed from fluids of known fluid composition (neutral versus acid pH) and temperature have been mapped for New Zealand (NZ) geothermal fields by visible/near-infrared (VNIR) and short wave infrared (SWIR) reflectance spectroscopy. Smectite, interstratified illite-smectite and illite formed from neutral pH fluids have zoned distributions with higher temperature illite (>220ºC) in and around the upflow of chloride waters and low temperature smectite (<150ºC) on the margins (eg Ohaaki, NZ). In adularia-sericite epithermal deposits, Au-Ag veins are similarly surrounded by zoned clays, with mineralised veins enclosed by illite (eg Martha, NZ) or occurring at the illite/illite-smectite boundary (eg Favona, NZ). Reflectance spectroscopy is also highly effective in identifying minerals formed from acid fluids; both steam-heated acid-sulfate waters (eg kaolinite and alunite at Rotokawa, NZ), or magmatic-hydrothermal fluids (eg pyrophyllite and topaz at Ngatamariki, NZ). These same alteration minerals commonly show zoned distributions in high sulfidation epithermal deposits (eg Rodalquilar, Spain) and in lithocaps associated with porphyry deposits (eg Lepanto, Philippines). Thus reflectance spectroscopy permits the rapid identification of key alteration minerals that can be mapped at a high sample frequency and used as vectors towards mineralisation.CITATION:Simpson, M P, Bignall, G, Rae, A J, Christie, A B and Chambefort, I, 2015. Mapping hydrothermal minerals in New Zealand geothermal fields using reflectance spectroscopy (VNIR-SWIR) and application to mineral deposit exploration , in Proceedings PACRIM 2015 Congress, pp 243–248 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By M Xu and, P F. Wells, A N. Kerr, Y Shields

Triethylene tetramine (TETA) has been used in combination with sodium sulfite (sulfite) for pyrrhotite depression at Clarabelle Mill since 1998. This combination has been highly successful at reducing pyrrhotite levels in the bulk (Ni/Cu) concentrate. Although highly effective, the roles of TETA and sulfite are not well understood. Treating bulk samples of the circuit feeds through the miniplant enabled the effects of circuit configuration on the performance of the pyrrhotite rejection circuits at Clarabelle to be determined. Reasons for the different performance of the non-magnetic pyrrhotite rejection circuit in the miniplant were investigated and tested in the laboratory. The effect of different grinding environments in the laboratory was examined to better understand the depressing mechanisms of TETA/sulfite. Modification of the grinding chemistry improved the selectivity of pentlandite over pyrrhotite in the presence of TETA/sulfite at current plant dosages.

Jan 1, 2005

By G Chen

Magnesite and dolomite are two salt-type minerals. The surface characteristics of these two minerals are almost the same. It is very difficult to remove dolomite from magnesite ores by flotation process. The present study was performed to develop a new collector and a better flotation scheme for magnesite from dolomite. The flotation tests show that there exists a significant difference in flotability between magnesite and dolomite when dodecyl phosphate synthesised with dodecanol, phosphorus oxychloride and other chemicals is used as collector. Sodium silicate was used as the modifier to improve flotation selectivity. It was found that sodium silicate selectively depressed magnesite at pH 4.5 - 7.5. The separation of magnesite from dolomite was achieved in a reverse flotation which resulted in a 76.1 per cent yield of magnesite with a grade of 47.3 per cent at 100 ppm dodecyl phosphate and 75 ppm sodium silicate. The flotation mechanism was investigated by characterising surface electrical properties and measuring the adsorption density of the reagents on magnesite and dolomite.

Jan 1, 2005

By T McConachy

New opportunities for miners are beginning to appear through new discoveries, improved knowledge and access to vast unexplored areas of the deep sea and continental shelf. Recent discoveries of undersea hydrothermal deposits show evidence of high-grade mineralisation, although in many instances the extent of the resource is still unknown. The promise and the difficulties of undersea mining have been evident since attempts were first made to mine manganese nodules in the 1960s. The physical nature of the undersea resource is a key influence on its mining potential; and environmental issues will also become increasingly important. This paper explores these issues and concludes with a description of the immediate to medium term applied research required to develop this industry and the spin off that such research can provide.

Jan 1, 2000

By L Keeney

Geometallurgy is not a mechanism designed to replace current geological and metallurgical deposit characterisation but an added component required to understand orebody variability. Current geological characterisation approaches focus on understanding deposit genesis aimed at identifying new mineralised regions and metallurgical characterisation determines parameters required for engineering design of processing plants. Geometallurgical integration has the task of drawing on aspects of each stream to enable spatial mapping of performance indices across a deposit. It is a complimentary activity to current practice and adds a new dimension to orebody knowledge. Although the notion of conducting an integrated geological and metallurgical analysis is not a new concept, limited publications exist in the field proposing integrated methods, with several technical issues existing in current geometallurgical integration approaches. An iterative method drawing on existing geological and metallurgical characterisation and new measurement tools and inputs is proposed. The integrated method comprises of discrete components dynamically linked together through iterative feedback loops with each component having a specific purpose achieved by applying a range of data acquisition technologies and statistical tests. The key outcomes of the method are:overcoming the lack of optimised geometallurgical domains relevant to processing performance,development of a rigorous approach to identifying parameters controlling processability,improved protocols for relevant metallurgical test data and sample selection, andability to generate greater data support to enable rigorous geostatistical modelling of geometallurgical attributes. This paper outlines the integrated mapping and modelling method developed and draws on multiple data acquisition technologies applied within the AMIRA P843 GeMIII Project.

Sep 5, 2011

The nickel ores mined in New Caledonia for one century are mainly silicate ores. These ores are nickel enriched saprolites, formed by partial weathering of peridotites (predominantly harzburgites and some dunites), serpentinised to varying degrees. Saprolites constitute the lower horizon of lateritic soils, sometimes up to 100 metres thick, developed on peneplains now greatly modified by erosion. Saprolites are generally overlain by laterites, a more weathered horizon, where the main components are iron oxy-hydroxides with a low nickel grade. The structure of saprolites depends essentially on the serpentine content of peridotites and, on the other hand, serpentine minerals may have a high nickel content and, so, represent important nickel bearing minerals in silicate ores. Two types of serpentines can be found in nickel ores from New Caledonia: ò primary serpentines, formed by hydration of olivine at temperatures below 400¦C, during overthrusting of peridotites in late-Eocene (Paris, Andreieff and Coudray, 1979), are generally very abundant; ò secondary nickeliferous serpentines, associated with other sheet silicates in garnierites, are now relatively scarce but garnierites were selectively mined one century ago, because of their high nickel grade.

Jan 1, 1996

During the intial two years (1972 - 1974) of exploration at Telfer, water require- ments were limited to supporting a 50 man camp and diamond drilling to verify thickness and grade of the stratabound ore deposit. Water bores were drilled to intersect the Middle Vale Reef down dip from its outcrop about 70 metres below surface. The MVR reef is an oxidized pyritic horizon which contains 30% - 65% sulphide below the zone of oxidation and forms a highly porous leached gossanous zone to a depth of 100 metres. Surface run-off water from the low hills associated with the Main Dome structure have led to annual re- charge of this extensive aquifer which MAP AREA Lake Waukarlyearly Permian rocks Precambrian basement - - ~;; rocks Sand d.n.s pò. _ « Drainage sg 1 qo~ (`-~.~ ? ò;+ Palaeochannel and 1 d {- subsurface drainage % GLENN BOREFIELD PASSMORE FAULT ;òTsI1. G-OId MIns BOUNDARY oChr~st as t .` Pool 4, 1 j`` Lake Dora òt ~daN 22' 0, 50 Niter KILOMETRES Fig 1. Telfer district map, Great Sandy Desert, Western Australia.

Jan 1, 1988

By McConachy G. W, Wright J. V

During the 110 years since the discovery of the Broken Hill PbZnAg deposit six major mining companies have mined the ore body and explored the ore environment. Despite this activity, no new orebodies have been found at Broken Hill. The failure to discover large new resources cannot be attributed to a lack of activity because major companies have maintained substantial exploration commitments over many decades. This suggests that not only was a unique coincidence of conditions required to form the deposit but also that full recognition and definition of the critical parameters may not yet have been recognised. In an attempt to illuminate some of the more unusual and poorly studied characteristics of the ore environment some new areas of investigation are presented here which may contribute to understanding the ore deposit setting and focus exploration towards different and perhaps more productive targets. Sedimentological characteristics of the host succession of the Broken Hill deposit are apparently unique along the line of lode. An upward-coarsening megasequence reflected in the development of clastic psammites stratigraphically below the ore deposit is one important ingredient which has received little exploration focus. These psammites also host mineralisation and form part of a spectrum of quart-zrich rocks collectively referred to as gametiferous psammites, garnet quartzites and blue quartz lodes. Sedimentological data interpreted from outcrop, drill core and downhole geophysical well logs support a elastic origin for some of these rocks; an interpretation which is at variance with traditional interpretations favouring an exhalative origin. A clastic origin for many of the footwall psammites, and their close spatial association with the orebodies suggests their role in ore formation was important. It is interpreted as a critical part of the fluid flow architecture within the sedimentary basin, which focussed ore forming fluids into an unique environment favourable for trapping mineralisation. Detailed stratigraphic correlation near the deposit has also highlighted that quartzofeldspathic rocks (Potosi gneisses and lode pegmatites) have complex relationships with ore. Suites of stratabound quartzofeldspathic pegmatites have received limited study, but their distribution and voluminous development suggests they may be as important to ore formation as the psammitic lode rocks which host the orebodies. These associations are not in conflict with some recent ore forming models invoking deposition in a shallow water environments of deposition. The geochemistry of parts of the host sequence has been studied extensively in the past but this has not been merged with current stratigraphic subdivisions. A large drillhole data base now permits the geochemistry to be related to the sedimentary succession and reveals that a signature involving stratigraphic vectors best illustrated by changes in MnO, Na2O, Pb and Zn can be detected. This is interpreted to reflect sedimentary basin processes as opposed to a classical volcanic hydrothermal alteration pipe associated with seafloor venting. The stratigraphic setting together with characteristics of some of these poorly understood areas is discussed to emphasise that construction of sound models for exploration requires the total ore environment to be studied with attention directed to the geometry and setting of the full range of host rocks. Control of the greater portion of the line of lode by a single company, Pasminco Australia Limited, now permits disparate datasets and observations to be merged and presents new opportunities and encouragement for model refinement and exploration success.

Jan 1, 1993

In October 2005 Phelps Dodge mining, a US based company, visited several Australian mining companies and mine sites to ascertain the current applications of risk management methods in the organisation. The results of this review, documented by the author, indicated a ælayeredÆ approach from high level site or major hazard analysis through to face level, æstop and lookÆ, methods. The approaches of several companies were summarised in one simple layered model. This model is helpful to other sites and companies to identify potential improvements but also offers an image of best practice that may assist with the governance of OH&S by both company boards and community regulators. The issue is particularly relevant as we discuss national consistency in mining regulation. This paper examines the layered model, the company and site approaches that helped define the model, as well as the suggested implications of the layered model to governance.

Jan 1, 2006

By Offler R, Lau J, Lea J. F

The stratiform and vein-type pyritic silver-Iead-zinc-copper sulphide deposits of Sunny Corner, NSW are hosted by acid volcanic and clastic sedimentary rocks of Middle Silurian to Early Devonian age. The rocks have been subjected to low-grade regional metamorphism (prehnite-pumpellyite facies) and three phases of folding and four faulting events are recognised. Pyrite is intensely fractured, indicating brittle deformation. Chalcopyrite and galena exhibit deformation twins and slip planes indicating ductile deformation; sphalerite and chalcopyrite show straight and curved grain boundaries and dihedral angles of 120° as evidence of annealing recryslallisation. Sulphur isotope ratios for 22 samples from five deposits range from 1.7 to 10.7 per mil and average 7.4 per mil. Sulphur isotope data are similar to those from other stratiform sulphide deposits in acid volcanic rocks of Late Silurian age in the eastern Lachlan Fold Belt, especially Woodlawn and Captains Flat and together with other features of the mineralisation, suggest a volcanic exhalative origin for the Sunny Corner deposits.

Jan 1, 1984

By B Chapman, R Nievergelt, J Hill

A major component of Sydney’s new South West Rail Link project is the Hume Highway Underpass (HHU), an 80 m long twin track mined tunnel excavated at a depth of just 5 m below the pavement of the Hume Highway; one of Australia’s busiest road corridors.In order to ensure a safe and efficient construction of the underpass without disruption to the Hume Highway traffic, design of the HHU required specific focus on the prediction and control of ground movements. This paper describes the design and construction solutions adopted in response to these challenging constraints. The paper also provides discussion on the observed behaviour of the underpass during construction and the results of a back analysis that was undertaken during construction.CITATION:Hill, J, Nievergelt, R and Chapman, B, 2014. Design and construction of Sydney’s South West Rail Link Hume Highway Underpass, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 375–386 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

This paper describes the new iron and steelmaking process recently commissioned at NZ Steel. Ironsand mined and concentrated at Waikato North head is slurry pumped 18 km to the company's Glenbrook works. Ironmaking includes the direct reduction process pioneered at Glenbrook in the 1970s and a new continuous electric melter. The molten, high carbon pig iron produced is then fed to a vanadium recovery unit and on to the KOBM oxygen steelmaking vessel. Steel is cast into billets or slabs. The new plant, which is the first stage of a fully integrated works at Glenbrook, raises New Zealand Steel's production capacity from 150 000 t/y to 750 000 t/y.

Jan 1, 1986