Search Documents

With the progress of modern mining engineering, one of the features of which is the mining from greater depths and the hoisting of greatly increased loads, it becomes a matter of increasing importance that the engineer should be able to determinewith some degree of precision the character of the strains on the hauling rope. But a wire rope is a complex structure; it is made up of spirally-twisted strands, which in turn are composed of spirally-twisted wires, and it is not particularly easy to say exactly what happens when this "doubly-twisted structure is wound round a drum or over a pulley.. The difficulty has been generally evaded in ordinary practice by the simple device of adopting a large factor of safety for the rope-usually from 8 to 10-a factor which experience has shown is sufficiently large to cover the bending strains set "up when the rope is passed over pulleys of the sizes commonly considered appropriate.When, however, we add the stress due to the bending of the rope to the stress produced by" the direct pull, we find that the actual factor of safety is usually more nearly 4 than 10, and frequently the bending stresses in the rope are so large compared with the simple tensile stresses that their neglect may easily lead to disastrous results when dealing with problems a little out of the common run. Common Empirical Rules.-It is always "recognized that the bending of a wire rope round too small a pulley is likely to do the rope serious injury, but as it is desirable in ordinary winding operations to reduce the inertia of the moving parts to a minimum...

Jan 1, 1907

A nine-month investigation was conducted into the effect on coke quality and blast furnace operation of the addition of bentonite and southern coal to the northern coal fed to the coke ovens at the Newcastle steelworks.Additions of 0·3 per cent bentonite or 25 per cent southern coal to the northern coal increased the coke strength from 15-20 A.S.T.M. stability to 25-30 A.S.T.M. stability. It is likely that improved mixing and blending facilities would, in both cases, give a coke of over 30 A.S.T.M. stability.For the same coke strength, the use of 0 3 per cent imported Wyoming bentonite was considerably cheaper than the use of 25 per cent southern coal, but the use of Australian bentonite promises the same coke strength for still lower costs. Other additives such as coke breeze, charcoal, iron ore fines, and certain other finely divided materials, gave relatively minor improvements in coke quality.There appeared to be sufficient improvement in blast furnace operation and production to justify full scale addition of bentonite to improve coke quality, although other variables, particularly iron ore physical quality, overshadowed on many occasions the effect of coke quality. Further coke trials with southern or bentonite will be carried out when ore quality has been improved by the introduction of ore sintering at Newcastle.INTRODUCTIONDuring the period of operation of the Newcastle coke ovens and blast furnaces from April 1960 (when No. 3 blast furnace was blown in after rebuilding) to December 1960, a bentonite coke trial was carried out based on earlier research findings (Gregory, 1959a, 1959b; Felton and Gregory, 1960; Gregory, 1960) that as little as 0 3 per cent to 05 per cent bentonite clay added to northern N.S.W. high volatile coking coals gave a significant increase in coke strength. The bentonite coke trial was followed by trials...

Jan 1, 1962

By Hang G, Hongtian X

In this paper, it is briefly introduced that China's Ordovician limestone confined-water menaces coal mining and Ordovician water is prevented and cured to secure the safety of coal mining. The theory of "Down-Three-Zones" is presented on the basis of research and practice in recent ten years. The concept of "Down-Three-Zones" of floor water-eruption is described clearly. Finally, the principle and method of applying the theory of "Down-Three-Zones" are discussed. 1. An Introduction of Damage: China is rich in coal resources. The conditions of coal field geology are quite complicated. There is an area of two million square kilometre of Karst limestone in nine million six thousand square kilometres of territory. The resources of underground water are rather plentiful, but this menaces coal exploration. Sixty percent of coal mines in China are damaged by limestone confined-water in different scales, particularly coal mines located the Carboniferous-Permian coal fields of the Ordovician limestone distribution area of Northern China. Because there is the 500-800 metre thickness of Ordovocian limestone and the well developed Karst containsl plentiful water, Karst water can have more than 100 Kg/cm pressure. Limestone aquifers have only distances of several metres or several decade metres to coal seam, Karst water can enter the aquituge and even the coal seam, large eruptions often occur. For example, a mine of 3 million ton production capacity had an eruption of 2053 cubic metres per minute. This is the largest confined-water eruption which has brought enormous economic damage and threatened the safe production of coal mining. Therefore, the prevention and cure of Ordovician water has immense advantage to the development of the coal industry. There are several decades experience in the prevention of Ordovician water-eruption in China. The prevention of Ordovician water-eruption has two kinds of plans. 1) dewatering and depression: it refers to dewatering of aquifers as roofs of seam and depression of aquifers as floors of seam in mining areas. 2) comprehensive prevention under the condition of having water pressure in aquiters. Due to enormous water, electricity, equipment and lots of other factors, the former isn't used extensively, the latter tits to China's actual conditions and is used widely. So-called comprehensive prevention under the condition of

Jan 1, 1988

The major copper orebody at Mount Isa is being extracted at a rate of four million tonnes per year. The method used requires an equivalent rate of back filling with (mainly) cemented fill. There were three major incentives for developing this mining system. The first was the prospect of high ultimate recovery of the orebody. The target is 100% recovery. Also the proposed stoping layout appeared to offer significant advantages in development and production costs. Finally, extensive subsidence above the northern end of the orebody could have disturbed permanent surface installations and jeopardised a possible future open cut. The full implications of this ambitious strategy were not apparent in the early years. Now, after twelve years of production the benefits are being realised and they can be weighed against the costs. Probably the most interesting result which comes from this analysis is the significance of cutoff grades and dilution factors in balancing mining and filling rates.

Jan 1, 1980

By Warren L. J

The recovery of phosphate minerals from the Mt Weld deposit by froth flotation has been studied by many researchers. Most of the flotation experiments were carried out with a tall oil fatty acid as collector and sodium silicate as dispersant and gangue depressant at pH about 10. Several rougher stages and cleaner stages and, sometimes, a desliming stage were included. The major difficulty was to reduce the Fe2O3 impurities in the concentrate to the required level. We used QEM*SEM (Quantitative Evaluation of Materials by Scanning Electron Microscopy) to provide a comprehensive and accurate mineralogical analysis of the flotation products. The analysis indicated that the Fe2O3 impurities were mainly recovered in the second concentrate, owing partly to the incomplete depression of the liberated iron oxides by the sodium silicate and partly to composite particles containing iron oxides. The selective depressing action of sodium silicate was improved by adjusting the variables such as the modulus (SiO2/Na2O), pH and time of standing of the stock sodium silicate solutions or by adding some polyvalent metal salts into sodium silicate solution. The flotation process was optimised to produce a phosphate concentrate with the required grade and recovery (38.6 per cent P2O5, 2.67 per cent Fe2O3, 13.7 for P2O5/(Fe2O3 + A1203), at P2O5 recovery of 81.5 per cent). The possibility of recovering the rare-earth phosphate, monazite, from the Mt Weld deposit by flotation was also studied.

Jan 1, 1991

The Vera Nancy orebodies, although simple in overall geometry, are in detail generally narrow, multi-veined and fluctuating in width, strike and dip. Tight geological control is required to optimise gold and silver production from this bench stoping operation. The processes used to model the resource and to control ore drive development have evolved since mining commenced in 1997. Grade control is a combination of orebody sampling, geological data collection, understanding orebody geometry and the optimisation of ore driving and stoping activities. Global resource modelling utilises mainly drill hole data which is largely superceded by drive development data as stope development progresses. The orebody has a relatively low nugget effect that assists in grade estimation. Rather than rely on sophisticated grade interpolation methods, resource estimation to-date has focussed on developing the geological understanding of the orebody to ensure the framework for estimation is correct. Drill data alone is not adequate to define deposit geometry for stoping . Drive data is used as the dominant data set for stope geology modelling once development for a stope is complete.

Jan 1, 2000

There are a number of examples of how environmental factors have been integrated into the water management aspects of mining projects. The Kingston Lignite project in South Australia, Pine Creek Gold Mine in the Northern Territory, gravel and sand extraction from the Nepean River flood plain near Penrith, and the Olympic Dam Project have all illustrated that consideration of environmental factors can be integrated with project developments, with beneficial outcomes for both the project and the environment.Each of the above cases demonstrated an individually significant environmental issue, directly related to the interaction between the proposed project and its environment. In each case, careful research and an integrated approach to the problem resulted in a solution that gave both maximum protection to the environment and optimum consideration to the economic feasibility and success of the proposed project.The solutions ranged from alternative mining methods and improved waste and water management through to the ultimate objective of converting a mining project into a major water-based recreation source. These examples have set a precedent that will contribute ignificantly to the successful development of future projects.

Jan 1, 1988

In any strip coal mining operation the aosL important single operating unit is the dragline. Because the capital and operating costs of a dragline are high, it is desirable to operate these machines at their maximum efficiency. Thiess Bros. Pty. Limited operate a Bucyrus-Erie 1350 Walking dragline at their Callide coal mine. The operating conditions at the Callide Mine are different from those of other coal mines situated in Central Queens ,nd. The topography is rugged, the coal seam is thick, and the overburden is hard and inter- HH,inded. Several different operating techniques for a large dragline working under these con- ditinns arc discrossmd it tt

Jan 1, 1978

By Akerkar D. D, Dey M. L, Mathur S. B, Chowdhury S. K R

The extraction of gold and silver from chalcopyrite concentrates has been investigated. In view of the recent interest in non-cyanide leachants for gold and silver, one such alternative reagent, namely thiourea, has been employed in the present work. Precious metal leaching was attempted from received copper concentrates as well as pre-oxidised concentrates. Pre-oxidation of the concentrates was carried out by three different methods, namely roasting, pressure oxidation and biological oxidation. After pre-oxidation and leaching of the base metals, the leach residues were subjected to further leaching for precious metal extraction. The results obtained on the extraction of gold and silver from received concentrates as well as pre-oxidised concentrates are presented and the effectiveness of the three pre-oxidation routes employed is compared.

Jan 1, 1992

By Askew JE

The large, massive low grade gold orebody at Mount Charlotte has demanded an innovative approach to mining engineering. In the last five years several advances occurred in the areas of rock mechanics, mass blasting, blasthole drilling and truck haulage.Successive crown pillar failures throughout the life of the mine had resulted in a continuous geotechnical program, mostly utilisingconsultants. The culmination of this workwas the development of a successful crown pillar support system. Several stopes have incorporated the technique and the most notable success has been the relatively large F3 crown pillar.In hole hammer drilling was introduced to the mine in 1979, but little work had been done to develop a blasting system to suit the 165mm diameter holes. A non-electric sequential blasting system was adapted for use at themine and up to 600,000 tonnes have been fired successfully in an individual blast. Problems with ground vibration were addressed although this work remains incomplete.

Jan 1, 1984

By Perring CS, Hill RE, Barnes SJ, Vallance SA

The Maggie Hays nickel sulphide deposit is located at latitude 32¦ 15 'S, longitude 120¦ 30' E on the Lake Johnston (SI 51-1) 1:250 000 map sheet. The deposit occurs in the Lake Johnston greenstone belt, in the Southern Cross Province of the Archaean Yilgarn Block, 500 kilometres east of Perth, Western Australia (Figure 1). The remoteness of the Lake Johnston greenstone belt and its poor access, restricted previous exploration activities and the full appreciation of the geology and its Ni-sulphide potential. It was not until 1991, when Forrestania Gold NL commenced exploration activities, that the geology of the ultramafic units and their potential to host significant concentrations of Ni sulphides were clearly established. This paper, which describes the geology and the characteristics of the Maggie Hays deposit, is based on the results of exploration by Forrestania Gold NL and a collaborative research agreement between CSIRO Division of Exploration and Mining and Forrestania Gold as reported by Perring, Barnes and Hill (1994), Perring and Hill (1995), Perring (1995 a and b) and Barnes, Perring and Reilly (1995). A comprehensive description of the geology, petrology and geochemistry of the deposit is being prepared for publication by CSIRO (Pemng, Hill and Barnes, in press).

Jan 1, 1996

By Seymour C. A

Peak Downs Mine, a five million tonnes a year coking coal operation, strip mines a, series of Permian coal seams. Seam thickness ranges from 0.5m to 5.0m, and seams consist of multiple coal plies with intermediate shale and mudstone partings. Four 47m3 draglines strip overburden to a cover depth of up to 60m. Coal loading is by 12m3 shovels and 14m3 to 18m3 front-end loaders. Parting removal takes place where the layer of shale and mudstone between seams exceeds 0.3m in thickness. Parting has been removed by a wide variety of earthmoving equipment in order to evaluate the problem and to select the optimum method from an operational and economic standpoint. Multi-seam stripping of the thicker seams is accomplished by working draglines from spoil- pile benches. Coal seams thinner than lm are recovered by dragline and stacked in the pit for later loading.

Jan 1, 1974

By Woodcock J. T, Millett R. N

It was shown that manganese dioxide could be used as an oxidant in acid thiourea leaching of a gold ore. Manganese dioxide could generate high redox potentials and was as effective as hydrogen peroxide in the leaching process. Results obtained under closely controlled leaching conditions confirmed that high redox potentials enabled faster dissolution of gold to be obtained but led to extremely high reagent consumptions (thiourea, acid, and manganese dioxide). Additions of sodium sulphite solution in an attempt to lower thiourea consumption by reducing formamidine disulphide back to thiourea were only marginally successful. Although thio- urea consumption was slightly decreased, the consumption of acid and manganese dioxide was substantially increased and there was no net benefit in using sulphite. Tests in which a single addition of mangan- ese dioxide was made before addition of thiourea minimized overall reagent consumption and gave only a slightly lower dissolution rate of gold. This is a promising technique for further Investigation.

Jan 1, 1987

The first hydraulic roof supports were installed underground in 1950s and ever since that time engineering developments have improved the supports in many different ways. However. advances in three main areas, the roof support mechanical design, hydraulic engineering and electronics have ultimately led to the point where, 35 years after that first installation. automation has been achieved and is now commonplace.The history of roof support automation has involved the continual integration of high technology engineering. Thera ate further possibilities for the future which combine to give some idea of the likelihood of there ultimately being a completely manless face.

Jan 1, 1991

By D Mukendi-Ngalula, G Hearn

Beach sand minerals from the volcanic rock structures of the Drakensberg, Kwazulu-Natal, (South Africa) have been processed. Screening, flotation, spiral concentration and magnetic separation methods were used either separately or successively in an attempt to concentrate monazite minerals. Products thereof and those from a long time (up to 72 hours) microwaves treatment of the finally produced ilmenite-bearing minerals have been studied using the M÷ssbauer effect spectroscopy. The 57Fe M÷ssbauer effect spectroscopy has demonstrated its versatility and power in monitoring the ilmenite internal reduction mechanism and products and, in characterising the iron-bearing phases contained in different products from the beach sand minerals processing. Microwaves heating of ilmenite for up to 38 hours reduced internally the Fe3+ from the ilmeniteÆs structure. A more prolonged microwaves heating (up to 72 hours) re-oxidised the mineral. 61 per cent natural ilmenite recovery was obtained in the floating products of a spiral concentrated -212+106 ¦m screened and beach sand minerals fraction. A preferential concentration of hematite with a 62 per cent recovery was found in the sinking products while the combination of screening-spiral separation-magnetic separation and flotation yielded a floating product with the highest ilmenite and the highest hematite abundanceÆs (71 per cent, 19 per cent respectively). A natural ilmenite containing 87 per cent ilmenite and 13 per cent hematite could be produced and extracted from the sinking products of the flotation process collected subsequently to the spiral concentration and the initial screening.

Jan 1, 2000

Silica and limestone fluxing levels in copper smelting slags were studied. Copper concentrates with flux additions were smelted to matte (55.5 per cent Cu) and slag in a pilot scale submerged combustion furnace.Results indicated that oxidic and sulphidic copper levels in slags were minimised with a slag Si02 level of 36 per cent and a SiO2/CaO ratio of 5.5. Total copper losses in slags were 0.6 per cent under these conditions.To produce the desired slag chemistry, additions of bulk silica and limestone to copper concentrates of fluctuating grades were predicted numerically. The method employed the solution of two simultaneous equations, each respectively for silica and limestone calculations.The predicted flux additions were applied in a further series of tests and the resultant stages were found to be satisfactory. The method is applicable to smelting 'operations which employ two flux bins, with weigh feeders, so that slag chemistry may be controlled with the flux/concentrate feed mix.

Jan 1, 1985

By Selischop F, Tredoux M

The distribution of platinum-group elements (pGEs) has been investigated in matte and slag samples from Waterval Smelter (Rustenburg Platinum Mines). The study showed that a strong preference of PGEs for alloy phases in matte represents a concentration mechanism that commenced in the furnace but can be considered a continuum from natural processes. Metal losses to fayalite (converter) slag occur by matte entrainment due to the mechanical capture of liquid sulphide droplets from the matte layer, and the exsolution of dissolved metal sulphide resulting from changes in the oxidation state of the slag. The latter is comparable to immiscible sulphide in basic magmas. However, the observed distribution of PGEs shows enrichment in metal phases of the matte. A mechanism is proposed whereby naked PGEs in silicate melts coalesce to form clusters which are stabilised by surface attachment of sulphur atoms. This envelope acts to 'draw the cluster into sulphide melts. Small particle melting effects permit PGE clusters to remain as liquids at magmatic and smelter temperatures.

Jan 1, 1994

By L Terrusi

The Bungaroo Valley hosts a concealed Tertiary channel iron deposit (CID) along a 17 km stretch of its length. Bungaroo Valley is approximately 0.5 km wide upstream at its easternmost extent, and 3.5 km wide downstream where it joins the Jimmawarrada Creek. The valley follows the axial trace of an anticline that plunges gently to the southeast, and the CID infills the valley. Mineralisation extends to a depth of 230 m below the surface, and almost the entire deposit occurs below the water table. Bungaroo Valley cuts through the Buckland Hills and is bounded to the north and south by steep scarps capped with the resistant Dales Gorge Member of the Brockman Iron Formation. Basement rocks are believed to be mostly Wittenoom Formation shales and dolomites, with Mount McRae Shale and Mount Sylvia Formation also present. Deep, localised depressions appear at the base of the CID sequence towards the north edge of the upstream section of the valley, while downstream the basal CID contact is relatively flat and shallow. In both cases the profile of the CID surface closely mirrors that of the basal contact. The localised depressions seen in the upstream basal CID contact produce significant variations in CID thickness of up to 100 m over short strike distances. This uneven palaeotopography is most likely due to eddying and waterfalls forming within the riverbed prior to CID deposition during a time when the water table was much lower than at present. It may also be associated with possible karsting in an underlying dolomite unit and subsequent syn- or post-depositional collapse of the overlying CID. The irregular basal contact of the Bungaroo CID sequence has implications for mining in terms of pit design and resource accessibility.

Jan 1, 2007

By Kuganathan V

The processing of black coal in Australia segregates waste in the form of coarse reject and fine tailings. The coarse reject is relatively easy to handle, while the tailings can be problematic. Conventionally, the two waste materials are disposed of separately, the coarse reject in dumps, and the tailings in man-made containments. Aqueous tailings slurry is pumped to a 'wet' tailings storage, where the fine particle size of the tailings limits dewatering. Their low bearing capacity and high compressibility result in tailings deposits being difficult to rehabilitate. Disposing of the waste streams separately moves away from the heterogeneous mixture in the undisturbed ground, and concentrates potential problems with each waste stream. The feasibility and desirability of the co-disposal of tailings and coarse reject by combined pumping is demonstrated. This technique is in operation at Jeebropilly Mine and is proposed for a number of other coal mines.

Jan 1, 1992

By R Barritt

Remedial options for a waste rock dump (WRD) were considered as part of closure planning studies at an active mine in Western Australia. To minimise the impact of any seepage from the landform it was determined that placement cover system utilising the moisture ‘store-and-release’ concept was appropriate. The purpose of the cover system was to:•Reduce net infiltration of meteoric water to attenuate peak concentrations for contaminants of concern in natural receptors to levels that can be assimilated without adverse impact to the surrounding ecosystem; •Provide a growth medium for establishment of a sustainable vegetation canopy; and •Improve current quality of surface water runoff from waste storage areas.The project comprised several phases of work: materials characterisation, numerical soil-plant-atmosphere (SPA) modelling and finally cover system construction and monitoring equipment installation.CITATION:Barritt, R, 2018. Conclusions from long-term cover system performance monitoring – a case study, in Proceedings Life-of-Mine 2018, pp 101–105 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018