Search Documents

By A Sainoki, D Fukuda, K Shioya, C Zhang, M Sharifzadeh, T Yamaguchi, S Saydam, J Kodama, C A. Amagu, Y Fuji

In an open pit mining, ensuring stability of rock slope has been one of the major challenges. As the instability of rock slopes can results in slope failures; consequently, endanger the lives of workers, affect mining operations, and often lead to economic losses. Therefore, it is practical important to study the stability of rock slopes to ensure safe, smooth, and effective mining. The stability of rock slope of about 130 m height at Higashi-shikagoe limestone quarry, which has experienced slope failures four times since 1996, was assessed. The rock mass at the quarry is consists of mainly limestone, schalstein and slate rocks intersected by clay seams of about 70 m thick at footwall of the rock slope. Previously, the effects of limestone excavation at the foot of the rock slope and shear failure due to rainfall infiltration have been investigated. Although clay is widely known to plays a vital role in the stability of slopes in engineering projects including mines, but its impacts on slope deformation at the study quarry are not adequately examined. Therefore, the present study addressed the impact of presence of clay on slope deformation at Higashi-shikagoe limestone quarry by employing both field displacement measurements and numerical simulation. Firstly, surface displacements measured by automated polar system (APS) for over eight years were analysed to understand the overall characteristics of the slope deformation. The measured results show that the displacement gradually decreases with time. The maximum displacement of about 100 mm was observed at middle of the rock slope. Secondly, the effect of deterioration and plastic behaviour of the thick clay layer were simulated using two-dimensional finite element method (2D FEM). The simulated results reveal that the clay exhibited deterioration by water contact and plastic behaviour arising from mining activities at the footwall of the clay zone. Based on the characteristics of the measured and simulated results, it was found that the displacement induced by the effect of deterioration of clay is more noticeable at the north side of the quarry whereas displacement induced by excavation is quite significant at the south side of the quarry if clay behaves as an elasto-plastic material.

Nov 29, 2022

By L N. Loganathan

Risk exposure in tunnel projects is extremely high due to various factors such as variability of subsurface conditions, selection of inappropriate design and tunnelling methods, improper risk assessment on adjacent surface and subsurface structures and utilities, and inadequate contractual practices. The risks in tunnelling must be borne by the contractor, designer and the owner of a tunnelling project. There have been a number of improvements in the last ten to 15 years in the manner in which tunnel projects are developed and implemented in terms of their design, construction, financing and operations. One significant improvement has been the manner in which underground conditions and their risks are being managed. Owners are less willing to transfer the full responsibility to the contractor for managing the underground conditions, although this is a familiar manner in which underground major urban projects have been previously contracted and managed. The owners of tunnel projects in Singapore have advanced the risk management process for their projects through geotechnical interpretative baseline reports (GIBRs), geotechnical data reports (GDRs) and project specifications (PSs). This paper discusses industry practice and its development as well as the application during the preparation and use in Singapore on the Deep Tunnel Sewerage System (DTSS) and the Marina Coastal Expressway (MCE) project in Singapore. The DTSS trunk sewer is 48 km and ranges from 3.3 m to 6 m finished diameter up to 50 m below the ground. The underground conditions ranged from Old Alluvium, strengths of about 1 MPa to competent Bukit Tima granite, with strengths of over 230 MPa. The total route length of the MCE is about 5 km. About 3.6 km will be constructed underground, consisting of dual five-lane carriageways. The underground construction will be cut-and-cover, and 2.6 km will be constructed about 13 m underground, and 1 km of tunnel will range from 13 m to 24 m as the tunnel passes under a 420 m wide reach of Marina Bay, whose crossing will be constructed as a two-phase cofferdam.

Jan 1, 2008

By D Pateman, F de Fredrick

The Bentley underground mine, which is located 60km north of Leonora, Western Australia, is owned and operated by Round Oak Minerals Pty Limited. A high-grade Zn-Cu Volcanogenic Massive Sulphide (VMS) orebody, Bentley was discovered in 2008 with production commencing in 2012. Long-hole open stoping is employed to mine the steeply dipping ore body, and in recent years the Avoca method has been adopted. This requires all development in a particular area of the mine to be completed prior to stoping commencing in a bottom up sequence. Voids are commonly backfilled with loose Run-of-Mine (ROM) waste loose rockfill (LRF); or alternatively cemented rockfill (CRF) can be used. Stopes in the 3860 AOS and 3900 AOS panels were located below previously extracted Avoca zones, with LRF situated immediately above them. These high-grade stopes were originally designed with rib and sill pillars to maintain control of the existing backfill during extraction. Due to changing factors over time, including mining economics, alternative options to achieve full extraction of the stopes were reviewed, including: • Mining small successive full height stopes which would involve drawing a blanket of LRF down with the extracted ore (stoping under waste); • Stabilisation of the existing LRF above the stopes and implementing a primary/secondary stoping sequence, with the primary stopes backfilled using a cement fill. An assessment of these options was undertaken which determined that the second full extraction method was the most beneficial to the operation, and could be achieved using a cement grout (Minova’s FB200 grout) to stabilise the LRF in conjunction with implementing a sequence where the primary stopes would be backfilled with cemented aggregate fill (CAF). Footwall drives were developed adjacent to the rockfilled stopes, allowing for the installation of horizontal grouting conduits, as well as providing access to the top of the planned 3860 and 3900 level stopes for the placement of CAF. An interval at the base of the previously rockfilled stopes was grouted at multiple horizons to achieve the required thickness, with a comprehensive quality assurance/quality control (QA/QC) process undertaken. Primary stopes were CAF backfilled via an arrangement of downhole winzes, linking the top of primary stopes to cross-cuts developed off the associated footwall drives. CAF was delivered underground through an open reticulation network that was extended to the specific levels. Overall the successful implementation of the revised mining method effectively increased ore recovery while maintaining control of overbreak and dilution, providing significant financial upside. This was achieved while maintaining effective controls in light of the changes to the risk profile. Stabilisation of the existing rockfill has allowed the extraction of stopes to full height, including the originally designed sill pillars, representing an average 23% increase in ore tonnes on the initial design, with dilution from the stope crowns averaging less than 1%. The use of CAF in association with primary/secondary stoping, eliminating the need for rib pillars, has yielded an average 47% increase in ore tonnes compared to the base case mine design.

Mar 15, 2021

By G Love, S Maher

In Victoria’s onshore Gippsland Basin, geology is driving brown coal developments, and geologists are key decision-makers. Prompted by volatile energy prices and the likelihood of a carbon constrained future, significant work has been carried out on the next generation of technologies to be applied to this giant resource. These include new-generation gasification technologies, coal conversion processes yielding products as diverse as diesel and fertiliser, drying technologies producing thermal and metallurgical coals and in situ conversion processes. However, coals aren’t coals, and brown coal available for new projects will have different quality parameters and mining economics from that currently mined.New projects are likely to be developed on coals with moisture contents averaging 60 per cent and corresponding low energy values. Whilst ash values will be low, averaging just 5 per cent (dry basis), this will at times approach 10 per cent, which is a level that would challenge the installed-generation technologies. Sulfur values will average 0.4 per cent (dry basis), but at times exceed 0.6 per cent, requiring technologies that address the potential for sulfur dioxide emissions. Whilst localised high levels of the fluxes iron (>1 per cent dry basis) and sodium (>0.3 per cent dry basis) would increase fouling of installed technologies, they may be suitable for selected next-generation technologies.Project viability for this next generation of technologies will be strongly influenced by mining cost, and geologists are playing a role in identifying higher-value coal. At its simplest, this is being achieved for open cut mines through regional, vertical strip ratio assessments, which are considered a first-order proxy for mining cost. Follow up assessments are incorporating mining and processing cost, coal quality penalties and product revenues. At a regional scale, it is informing the likely location and relative timing of future mine developments, as well as thinking around rehabilitation strategies, infrastructure and land-use planning.For deeper coal, factors like macro permeability, the ability to isolate seams from aquifers, groundwater chemistry, pressure temperature conditions, connection with groundwater recharge and in situ biota are being used as vectors to in situ coal conversion opportunities.Matching coal to the next generation of technologies has benefited from regional-scale geological studies of coal quality and mining economics, and has benefited from early engagement between geologists, technology developers and project proponents.CITATION:Maher, S and Love, G, 2014. Matching brown coal to the next generation of Latrobe Valley projects, in Proceedings Ninth International Mining Geology Conference 2014 , pp 77–84 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By M Graham, R Brunning, C Andringa-Bate, S Westergren

In 2010, Rio Tinto Iron Ore’s operations commenced the planning and design of a sampling and analysis system for the new 50 Mt/a Cape Lambert Port B (CLB) facility. Current sampling systems at the ports consist of automated robotic, mass-based sampling protocols employed at Dampier, and semi-automated, time-based sampling systems operating at Cape Lambert Port A.The new sampling system at CLB has brought together a fully automated sampling and analysis system utilising time-based sampling, with the capacity to sample ore products of medium quality variation as defined in ISO 3082 (ISO, 2009). The CLB system is required to sample at shiploading rates from 6000 t/h to 13 440 t/h and provide full load-port analysis. The sampling approach is to proportionally extend primary increments (of varying mass relative to shiploading rate) to a standard length using variable speed aero-belt conveyor systems. This enables a fixed number of secondary cuts to be achieved for all primary increment masses and to be delivered to the automated cell. The cell is required to be capable of concurrently processing four individual shipments, each containing multiple cargoes.Achieving the target sampling precision for all export cargo sizes has culminated in the planning, design and construction of the largest automated iron ore port laboratory in the world. The CLB sampling and analysis cell was commissioned in Q3 and Q4 2013. This paper discusses the sampling philosophy and commissioning outcomes.CITATION:Brunning, R, Andringa-Bate, C, Graham, M and Westergren, S, 2014. Cape Lambert Port B shiploading, sampling and analysis, in Proceedings Sampling 2014 , pp 79–90 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

A co-operative research project, combining Commonwealth Scientific and Industrial Research Organisation (CSIRO) research scientists findings and company iron ore geologists' expertise, resulted in new concepts about the origins, distribution and complexitie of iron ores and their parent rocks (banded iron-formation or BIF) in the Hamersley Iron Province of Western Australia. Understanding these problems was important to the efficiency of exploration, development and ultimate mining of iron ores. This genetic model, based on a detailed mineralogic background, was modified by Mt Newman geologists to obtain a user oriented classification for practical application in the field.The proposed Pilbara Iron Ore Classification (PIOC) gives iron ore geologists a basis from which to understand, identify and record the various mineralogic and physical characteristics of the many genetically different ore types occurring within and between orebodies in the Pilbara. More definitive quality control over ore products can be achieved based on the detailed understanding of ore types which the PIOC allows, compared to current classifications which deal only with the physical nature of ores. Of equal importance, the classification remains sufficiently simple to enable owners, operators and buyers to achieve a basic appreciation of ore type variations.With little modification, it is believed the classification has applications beyond the Pilbara, to iron ore worldwide.

Jan 1, 1984

By Thompson AG, Cadby GW

The New Austrian Tunnelling Method (NATM) is a proven concept for the safe and economic construction of underground facilities. This is especially true for tunnelling activity where changing ground conditions are often encountered. However, the principles central to the NATM have gained only limited use within Australia, presumably due to the measurement process inter- fering with tunnel driving and the cost associated with instrumentation and interpre- tation expertise. The design and operating principles of two basic instruments are explained together with laboratory simulated test results and suggest- ions for use in an integrated NATM style approach to underground excavation and construc- tion. The two instruments monitor load in rock reinforcement and deformation in rock or primary and secondary linings. The instruments may be fitted with a miniature display module which outputs the measured parameter in engineering units directly. The design of the sensing components allows the instruments to be installed in various configurations suitable for routine performance monitoring, quality control, support element testing or detailed investigations. The display module which reduces the need for instrumenta- tion expertise should suit contractors and allow performance data to be obtained which quickly may be used to modify support procedures to suit ground conditions. When complemented by convergence measurements the devices enable most facets of the NATM to be implemented.

Jan 1, 1987

Two key elements in the design of a pastefill or high density backfill system are the preparation of the backfill material and its distribution underground. This paper examines these two areas. Owing to the essentially impervious nature of total mill tailings, preparation of pastefill and high density fill from current tailings involves a physical dewatering process. There are currently three methods available for this process: Vacuum or pressure filters. These represent the ætraditionalÆ approach to the preparation of pastefill. Paste production storage mechanism. This is a thickening/storage mechanism developed with the specific objective of producingpaste/high density backfills. Fluidization. This system utilises silos fitted with simple dewatering devices and nozzles. Recently developed by CANMET, it provides the simplest and most economical approach.This paper describes and compares the three preparation methods, from a practical and an economic point of view. Once the pastefill/high density fill has been prepared and binder added, the backfill must be distributed underground into the stopes. A fundamental factor in the design of a distribution system is the rheology of the material. No two materials will exhibit the same properties, and a sequence of rheological and related testing is required prior to the completion of the design of the underground distribution system. This paper covers the testwork normally required and discusses the fundamental design parameters of pastefill distribution systems. The final section of this paper summarises the use of pastefill at three mines in Canada.

Jan 1, 1998

By J Kuva, M Parian, B I. Pålsson

One of the main factors affecting the suitability of an ore for autogenous grinding is the ore’s competency, ie providing enough critical stones for the grinding process. Several experimental test routines exist and are used for assessing the viability of the ore for autogenous grinding. However, very little attention is given to the generation of fatigue in large stones experiencing repeated shocks in the mill. To investigate this, large pebbles sampled from an industrial autogenous grinding mill running hard and soft ores were categorised based on the grinding energy. From the pebbles, small drill core samples were prepared and went through a series of fatigue cycle tests. Both hard and soft ores showed similar average resistance to failure in compression tests, but the hard ore had a consistent resistance with lower variations. The cores were scanned by XCT before and in-between fatigue tests at the highest reachable resolution, 1.5 µm voxel size. The outcome showed that a higher number of micro-cracks were visible in the soft ore compared to the hard ore. The frequency of micro-crack development in the soft ore may be the reason for its lower specific grinding energy compared to the hard ore. It is obvious that for realistic conditions in an autogenous grinding mill, stones are pre-weakened by fatigue before they fracture. Therefore, shortcut methods focusing only on running tests on fresh and small samples may operate in unrealistic conditions by ignoring the fatigue phenomenon. This is even more important for ores that are on the borderline to be considered as competent for autogenous milling.

Aug 24, 2022

By B Taylor

The Perseverance deposit is the most southerly known economic copper/gold deposit within the Cobar gold field. The deposit is situated approximately 12 km to the south-southeast of Cobar and is essentially blind to surface with the top of economic mineralisation occurring 750 m below ground level.Based on the December 2010 resource estimate (inclusive of reserves and net of depletion) the deposit contains 3 011 000 tonnes at 6.1 g/t Au and 0.90 per cent Cu (590 000 oz of gold and 28 000 tonnes of copper). The deposit is comprised of four principal lenses, the Perseverance, Hulk, Zone B, and Hercules lenses. In excess of 90 per cent of the known resource tonnes are contained within the Perseverance and Hulk lenses. The deposit is shear related and hosted within lower Devonian rocks of the Cobar Basin. The competency contrast of rhyolites juxtaposed against sediments by the Peak-Perseverance shear is the principal control on mineralisation. Both the Perseverance and Hulk lenses are primarily hosted by brecciated rhyolites juxtaposed against Chesney formation sediments across the Peak-Perseverance shear. This faulted rhyolite sediment contact roughly defines the global orientation of the deposit. The Perseverance lens continues within the shear for up to several hundred metres beyond the extent of the faulted rhyolite sediment contact. Mineralisation within the shear beyond the faulted rhyolite contact zone is hosted by sheared silicified sediments. The Perseverance lens remains open at depth and to the south.The Zone B and Hercules lenses, which are significantly less important in tonnage terms, are hosted by rhyolite breccias within the main body of the rhyolite and appear to be only tenuously related to the Peak-Perseverance shear. Within the Perseverance lens, the presence of northeast trending high grade breccia veins developed oblique to the north-south trending shear system has led to the development of steeply north plunging high grade ore shoots within a globally north-south trending mineralised domain. These high grade shoots have limited horizontal continuity but significant down plunge extent.The presence of coarse gold and the resulting strongly skewed nature of the gold grades, in conjunction with controls on mineralisation which are not parallel to the mineralised domain, has led to predictive difficulties regarding stope performance.Strong heterogeneity of the gold content of the ore and geological controls on mineralisation which are not parallel to the global trend of the mineralisation impose a set of difficulties which sound geological control is helping overcome.

Aug 22, 2011

By K P. Crameri

The Beta Hunt orebody is situated on the south western limb of the Kambalda dome. It is one of the nickel occurrences in the area which fall into the category of æKambalda Style OrebodiesÆ. These orebodies are renowned as being continuous uniformly mineralised ribbons of nickel sulfide mineralisation. Interestingly, Beta Hunt does not conform to this notion of continuity and uniformity and is in fact highly irregular in its ore distribution due largely to the influence of post depositional structure. In an attempt to understand the ore distribution at delineation stage rather than development stage a detailed footwall topography model is created using all available drilling data. To augment this drilling data, the routine use of downhole EM and borehole radar has been introduced to provide data beyond the confines of the drill core to enhance the geological interpretation of the footwall topography and the distribution of the mineralisation. The implementation of a detailed footwall model and the use of downhole geophysics has proved to be very effective in resolving the orebody complexity issues. Ongoing development of the methods used will continue to refine the interpretation of the geology to enable more efficient extraction of the orebody.

Jan 1, 2006

Gold and copper mineralization in the Parkes area is hosted by a meridional sequence of Late Ordovician to Early Silurian igneous and sedimentary rocks on the central northern edge of the exposed Lachlan Fold Belt. The mineralized area straddles two zones separated in part by the Parkes Thrust and exhibiting different styles of deformation and mineralization (Figure 1). The western zone is characterized by gently folded rocks, with shallow dips and weak to non-existent axial plane cleavage. Faulting is restricted to directions oblique to bedding. Numerous occurrences of minor copper mineralization are known, but of recent national importance is the discovery of the Coradgery- Goonumbla porphyry copper-gold deposits by Geopeko Ltd. A resource in excess of 250 million tonnes has been delineated (Jones, 1985), and this represents the first porphyry deposit of sufficient grade and tonnage to be potentially mineable in New South Wales. The eastern zone is much more strongly deformed. Folding is tight with strongly developed axial plane cleavage. Faulting is abundant both parallel and oblique to bedding. Quartz veining is also abundant, and a narrow belt of gold mineralization adjacent to the Parkes Thrust stretches from Forbes in the south, through Parkes and Peak Hill, to Tomingley in the north. Over 31 tonnes of gold have been produced from this gold belt, mostly before 1914, and now three deposits show good potential for redevelopment - Peak Hill, and the London-Victoria and Lachlan lines of lode.

Jan 1, 1987

By Thornton D, Esterle J, La Rosa D

Control of blast fragmentation has a significant impact on coal mine profitability. Two approaches for the characterisation of coal blastability, particularly in terms of fines, are presented. Both approaches were implemented for the predictio

Jan 1, 1998

By Simpson JF, Murrie SJ

In determining new areas for slag disposal a foamed slag aggregate has been developed for use as a skid resistant material. The foaming of the slag does not rely on the use of water, but rather on the slag chemistry. Laboratory test results indicated that a product having good skid resistant properties has been prod- uced. A section of road is being assessed for performance of the aggregate in a surface dressing application under heavy load. The results from the test section after seven months have shown that the foamed slag is suitable for this application. Further test sections are now being considered.

Jan 1, 1979

By C K. Boafo, J Visser

Obuasi Mine in Ghana, with more than 100 years of mining history, developed from a surface operation into a deep >2000 m underground gold mine. The challenge is to extract value from narrow veins left after extensive mining in the wider ore zones of the mine. Since the merger of AngloGold and Ashanti Goldfields in 2004 the mine strives to achieve optimum extraction through an integrated Mineral Resource management process from geological modelling, resource evaluation to mine design and scheduling. The shear hosted gold deposit displays complex secondary shears of variable thickness and continuity. There is an ongoing process of changes taking place in the way that geological modelling and resource estimation is done. Recent developments include the use of computerised systems that support the whole resource management chain from resource modelling to reserve optimisation. The change in thought and technology now allows for targeting narrow veins previously ignored in optimisation and mine design since moving into mechanised mining. The increased knowledge and confidence in the resource models now allows for flexibility in mine design, selection of mining method and scheduling and extraction of the reserves. The focus area for change is the way the orebody is evaluated and extraction designed. Since 2005 major changes were made to the process. This paper considers the historical approach of resource management. It looks at the individual process changes and qualifying the way ahead.

Jan 1, 2008

Several new techniques. which may be applied with advantage to the search for uranium are described. Scintillation type gamma spectrometers are now available for airborne', ground and borehole use. These can distinguish in a broad way between anomalies due to uranium, thorium and potassium. Gamma spectrometers based on semiconductor detectors now under development should be capable of much greater resolution. These should also make possible rapid, accurate and cheap radiometric analyses of samples containing uranium and/or thorium, whether in radioactive equilibrium or not. Another valuable prospecting aid, particularly in areas of tropical leaching, is systematic sampling of soil for radon content. Equip- ment for this purpose is currently available and it will be possible to extend the method when development of an alpha probe suitable for use in deeper holes is completed. Variations in the concentration of certain trace elements'in soil (e.g. mercury) also offer promise in the search for mineralized zones which may contain economic eon¦- centrations of uranium.

Jan 1, 1968

By U Singh

This paper presents the evolution of the studies and strategic plans to extend the life of operations at the Savage River iron ore project in north-western Tasmania. The current Life-of-Mine (LOM) plan for the Savage River operations is based on a series of open pits. Drilling has confirmed high-grade extensions of the magnetite resource at depths that exceed practical limits for open pit mining. Grange Resources Limited, the owner of the operation, is investigating underground options – not only to extend the LOM plan but also to maintain peak production at a reduced operating cost while reducing greenhouse gas emissions into the future. What makes this project unique is that it requires introducing a productive and cost-effective mining method to exploit a challenging geotechnical and geometrical orebody in an area of high rainfall. To support the study efforts, the development of an exploration decline, underground drilling programs, and an exploratory drive excavated into the orebody for geotechnical investigation was key to providing the necessary data for a pre-feasibility study (PFS). This paper describes the pragmatic approach and processes to developing the underground mining options study through data collection and then integrating these options into the open pit plans to optimise an overall strategic plan for the Savage River operations. The learnings for operators from this experience are how the technical and pragmatic approaches were aligned to develop the strategic plans, and the importance of timely investment in gathering the necessary data.

Mar 29, 2023

By M Rayner, C Tsouris, A Komelkov

X-ray fluorescence (XRF) is a widely accepted technique for the elemental analysis of iron ores and their concentrates. Wavelength-dispersive, or WDXRF, and energy-dispersive, or EDXRF, spectrometers offer distinct advantages for particular applications, elements and concentration ranges and are, therefore, more complimentary than people might realise. A key example is the ability of EDXRF to identify, and often quantify, unexpected elements in production samples that would typically be missed by routine WDXRF. In this paper we discuss recent technological advances in XRF and present a novel application example that demonstrates the additional technical and practical benefits of using both EDXRF and WDXRF to characterise iron ores and concentrates.CITATION:Tsouris, C, Komelkov, A and Rayner, M, 2015. A novel approach to the characterisation of iron ores and concentrates using recent advancements in wavelength- and energy-dispersive x-ray fluorescence spectrometers, in Proceedings Iron Ore 2015, pp 591–594 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

Zinc alloy castings continue to account for a very large, world-wide end-use market for zinc. However, an ever expanding multitude of other materials and processes are increasingly providing viable, cost-effective alternatives to designers, many of whom have no particular allegiance to any one industry. In order to meet this challenge, innovation of and for the zinc hot chamber pressure die casting process, in concert with sustained and inventive market development, is clearly required. While 'Quality' is now the watchword, and the goal of zero defects is being rigorously pursued, other important goals which must be addressed include net shape casting, enhanced productivity and increased energy efficiency. The paper gives an overview of several practical, process-orientated, projects designed to help achieve these goals. For example, a project designed to understand and precisely measure dimensional changes of castings with time has provided some of the critical information needed for net shape casting. A second study is looking anew at surface quality in relation to process conditions as an important step toward the goals of zero scrap rate and increased productivity. Developing the correct die casting machine parameters for achieving optimal quality and properties of zinc (ZA) die castings is a further example of research designed to benefit both the die caster and his customer, chiefly the original equipment manufacturer (OEM). A project on die soldering or galvanising in response to varying process parameters is similarly being considered in order to foster increased understanding and avoidance of problems, with a special interest in the use of special coatings. The maintenance or expansion of the future market for zinc die casting alloys also depends on design for functional applications, as an adjunct to their traditional decorative use. The role that alloys with enhanced properties can play, such as ZATEC, a new high creep resistant alloy developed specifically for elevated stress/elevated temperature applications, will be briefly discussed.

Jan 1, 1993

By B Olsson, B Reynolds, R Norman

An unprecedented growth in demand for coal exports has placed pressure on multi-user coal chains to guarantee that their capacity expansion projects will meet the required demand. These projects, however, are taking place in an increasingly complex commercial and technical environment - competing rail and coal terminal service providers as well as a myriad of competing mine operators, all needing to operate in an increasingly integrated manner to get the most out of expensive shared assets.Increasing system complexity and integration has driven the need for more holistic and sophisticated analysis tools. The capacity of coal chain subsystems, such as mine, rail and port, can no longer be determined effectively in isolation. Understanding the nature of the interactions between these subsystems, their sensitivity to uncertainty and the resultant capacity of the integrated system is the key to both maximising value and minimising risk.Recently, TSG has worked closely together with the Integrated Logistics Company and a number of key stakeholders in the Dalrymple Bay Coal Chain to develop independent system master plans. These master plans have provided a quantitative and rational assessment of coal chain capacity in its current state and a prediction of its capacity once a pipeline of committed capacity improvements is in place. This paper provides an overview of the study and a comprehensive guide to the process required to effectively achieve valuable strategic insights in a challenging multi-user stakeholder environment.CITATION:Reynolds, B, Olsson, B and Norman, R, 2012. Using independent system simulation to mitigate risk in the Dalrymple Bay Coal Chain, in Proceedings Project Evaluation 2012 , pp 77-84 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012