Search Documents

By Sandvik

Fine grinding in an air-swept ball mill working in closed circuit with a forced vortex air classifier has been investigated first in continuous laboratory and then in industrial scale. Results from the laboratory circuit have shown significant influence of mill load (powder filling) on the capacity of the circuit. In laboratory scale the mill load was measured and controlled by a weighing platform placed under the complete mill set-up. The mill load of the industrial air-swept ball mill has till now been controlled by measuring the power consumption of the mill motor. Thus, it was necessary to operate far from the range of optimal mill filling. To improve the circuit performance, alternative ways of mill load measurement were investigated. An important factor was investment cost, as many fine grinding mills operate in relatively small circuits that do not wan-ant large investment. In this case the task was accomplished by using a piezoelectric strain transducer, which detected strain changes in the mill shell. It was installed in the midpoint of the shell, where the highest deformation was obtained. As the transducer was on the top position, it indicated compression, and on the bottom position it measured tension. By taking the difference between the readings, it was possible to calculate total strain variations, directly proportional to the mill load. The signal from the transducer was sent to a control room via a cordless infrared communication system, employing a microprocessor control card, which could further regulate other operating parameters of the circuit according to the software model. The installation required very low investment cost and provided simplicity of application as well as stability and reliability of characteristics under severe industrial condition. The measurement system made it possible to optimise the mill load and thus increase the production from 3.2 to 3.7 dh (15 per cent), and stabilise the circuit operation.

Jan 1, 1995

By M J. Nugus, J G. McLellan, T G. Blenkinsop

High fluid pressures and deformation have been instrumental in the formation of high-grade gold lodes at the Archaean granite greenstone 12 Moz Sunrise Dam gold deposit in Western Australia. Historically, predicting the location of these lodes has been difficult due to the irregular nature and high-grade nugget characteristics of the deposit. Recent exploration successes and the discovery of the Vogue system have led to an improved knowledge of the deep extents of the mine. This new structural and gold distribution data has enabled a new 3D interpretation of the system and has provided a better insight into the links between deformation, fluid pressure evolution and gold deposition. Here we employ 3D geomechanical and coupled fluid flow modelling to better constrain areas of high strain partitioning, rheological failure and focused fluid flow, which provides a substantially increased predictive capacity for further within-mine exploration. The localisation of deformation in and around the main felsic porphyry and major shallow shear zones provides critical insights into fluid pathways that have contributed to the distribution of fracture networks and ultimately gold deposition during late stage deformation events. Understanding the relationship between deformation events, fluid pressure evolution and the partitioning of strain is paramount in understanding the distribution of gold and for focusing on future target areas.CITATION:McLellan, J G, Blenkinsop, T G and Nugus, M J, 2013. Fluid pressure, geomechanical evolution and predictive targeting of the Sunrise Dam gold deposit, Western Australia, in Proceedings World Gold 2013 , pp 419-426 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

Mining operations in the Obuasi mine of AngloGold Ashanti Limited began in 1897 using mainly gravity concentration and amalgamation to recover the gold from predominantly high-grade quartz ores. The mine is primarily an underground operation, although some surface mining still takes place. Ore is currently processed by two main treatment plants: the Sulfide Treatment Plant (STP) for underground ore and the tailings treatment plant for tailings reclamation operations. STP was commissioned in February 1994 to treat 180 000 t/m of double refractory gold ore and it hosted the then world's largest commercial scale bacterial oxidation plant which uses Gencor's BIOX« technology. Gold is recovered by gravity and flotation, with the regrinding of the sulfide concentrate before bio-oxidation to liberate locked gold in sulfi de minerals. The BIOX« product is leached using the carbon in leach (CIL) process. Gravity gold recovery is a major component of STP operations and its contribution to overall plant recovery is about ten to 13 per cent. Gravity recovery has undergone series of technological upgrading, since the very first circuit which consisted of a Knelson concentrator and a Gemeni shaking table which was incorporated into the milling circuit at the start of the plant. Presently, each of the gravity circuits which consists of Knelson concentrator(s), cyclones and Gekko InLine Reactors (ILR), are located at the Milling and BIOX« circuits. More recently a new gravity recovery facility comprising of four 48 inch Knelson concentrators and cluster of ten inch cyclones have been incorporated at the tail of the flotation circuit. An additional ILR will be commissioned in 2010 to treat the concentrate generated from the new Semi Autogenous Mill #2 (SAG 2) Knelson: concentrator tower under construction. Since the inception of STP, significant gravity recoverable gold has been recovered via Knelson concentrators and the employed circuits have seen a number of modifications and upgrades, motivated by ore mineralogical changes and recovery concerns. The pioneering adoption of the ILR technology in 2001 and 2003 was a critical factor in enhancing the improved recovery benefit of the gravity circuits. Therefore the objective of this paper is to highlight the mine's experience in the gravity recoverable gold process with emphasis on plant modifications and gravity equipment upgrade. Operational challenges and the contribution of gravity gold to overall plant recovery are also discussed.

Aug 1, 2010

By M J. Nugus, F Clark, E J. Hill, J T. Carswell, J S. Cleverley, N H. S Oliver

High-nugget gold orebodies are difficult to model in 3D because samples from diamond drill core are generally too small to provide reliable estimates of the gold content of the larger body of rock, and therefore interpolation of gold assay values between drill holes is also unreliable. As a result, gold resources are generally underestimated in areas of high nugget. In practice, proxies for gold mineralisation, such as presence of alteration, specific structures or high vein density, have been used by geologists to predict rocks which are favourable for mineralisation. However, there has been no automated method for combining the predictive capabilities of several proxies, except by human judgement.We have been developing a method to combine several different types of geological features or geochemical analyses into a single measure using conditional probability. Conditional probability provides a meaningful numerical measure for the favourability of rocks for containing high-grade gold mineralisation. This measure can be interpolated in the exploration space, providing a sound basis for a 3D model of the orebody. We have developed this technique using data from the Sunrise Dam Gold Mine, which is a high-nugget orebody hosted in a structurally complex Archaean greenstone belt and which has historically proved to be a very challenging orebody to model.CITATION:Hill, E J, Nugus, M J, Clark, F, Oliver, N H S, Cleverley, J S and Carswell, J T, 2013. Predictive three-dimensional modelling of nuggety gold orebodies, Sunrise Dam, Western Australia, in Proceedings World Gold 2013 , pp 463-468 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By S Morgan, L C Pagdalian, S Serdzeff, C Malaloy-on

It is widely accepted that mineral deposits are decreasing in metal grades. To remain profitable and meet market demand, mining companies are expanding their operations by increasing the tonnage treated. These expansions may include new concentrators with higher nameplate tonnages or upgrading the capacity of existing ‘brownfield’ operations. In many cases, the brownfield upgrade route is preferred as it is less capital intensive; however, brownfield upgrades are never straightforward and present many metallurgical and engineering challenges.For example, to increase feed throughput at a brownfield site, there will be a requirement to modify the mine development plan. This may result in the ore mineralogy varying beyond the current feed fluctuation range. To accommodate these ore variations, a combination of mineralogical analysis and small scale testwork can be used to develop a new process flow sheet to achieve the product recovery/concentrate grade requirements. In general, however, flow sheet development does not usually consider site specific layout constraints and equipment requirements. At sites where future expansions were never considered, taking this silo approach could lead to project delays and compromise the circuit design.Engaging an experienced technology partner ensures the nominated project team is involved throughout all stages and aspects of a given brownfield upgrade – from conceptual flow sheet development, through to detailed engineering, construction and commissioning. The recent Carmen Copper Corporation (Carmen Copper) circuit upgrade has been completed in technology partnership with Outotec. The circuit upgrade was extensive and included new equipment additions to the comminution, flotation and dewatering circuits. Carmen Copper’s intimate knowledge of the ore characteristics, in conjunction with a trusted, knowledgeable technology partner, facilitated a robust circuit design, and fast-tracked the project execution. This paper deals specifically with the flotation circuit upgrade and highlights the benefits to Carmen Copper of this holistic approach.CITATION:Morgan, S, Serdzeff, S, Malaloy-on, C and Pagdalian, L C, 2014. The benefits of technology partnerships during brownfield upgrades, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 471–476 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By R Lastra, Y Choi, C Hamilton, P Kondos

Hydroseparation (http://www.cnt-mc.com) was used to concentrate sized fractions (from <38 ¦m to 150 ¦m) of various ore products ahead of carbon-in-pulp (CIP)-treatment. The resulting size-by-size concentrates were mounted as monolayer polished sections and subjected to automated unattended precious metal searches by image analysis (see Lastra, Wilson and Cabri, 1999). Systematic variations in Au-deportment permit quantification of Au reporting as discrete grains from fresh-feed through to pressure oxidation (POX)- and CIP-feed. Application of hydroseparation, image analysis and assays to characterising tailings (from <10 ¦m to 106 ¦m) from four mine sites is also described. Results are encouraging enough to predict that the combination of hydroseparation (HS) and automated image analysis could become a standard methodology for study of precious metal ores and metallurgical products.

Jan 1, 2008

The Lane Cove Tunnel (LCT) is an important infrastructure link in New South Wales (NSW) and runs from the end of the Gore Hill Freeway at Artarmon at its eastern extremity, to the end of the M2 at North Ryde at its western extremity.  The LCT is 3.6 km long and generally consists of twin two/three lane unidirectional tunnels running largely under Epping Road from just east of Mowbray Road, west to the western end of the Gore Hill Freeway. The tunnel opened in early 2007. The presentation will provide a summary of the traffic and emission modelling performed for selected representative surface road sections in the vicinity of the Lane Cove Tunnel. An assessment of the predicted impact of vehicle emissions on ambient air quality in the corridor as a result of changed traffic conditions due to the tunnel opening will be presented. The traffic modelling and emission calculations were undertaken for the following two scenarios: Year 2006 û Lane Cove Tunnel no-build option, and Year 2006 û Lane Cove Tunnel build option. Vehicle emission calculations for the four main pollutants from vehicles: CO, VOC, NOx and PM10 on the surface roads in the vicinity of the Lane Cove Tunnel were performed using the predicted daily traffic for the two cases (no-build and build). The analyses indicated that the vehicle emissions for all pollutants are expected to significantly reduce in the corridor with the building of the Lane Cove Tunnel, including the areas in the vicinity of all tunnel portals, when compared to vehicle emissions for the no-build case.  As a result of the decreased vehicle emissions on the surface roads, the study concluded that the actual ambient air quality is expected to improve in the corridor including the tunnel portal areas after the Lane Cove Tunnel opening.

Jan 1, 2008

By M Grigorescu, J H. Hodgkinson, H Alehossein

A new framework that collates and interprets pre-existing data to assess vulnerability and ultimately plan to avoid or minimise flood-related risk to infrastructure, people, downtime, environment and revenue has been developed. The æClimate Related Adaptation from Terrain Evaluation ResultsÆ (CRATER) method tested at a coal mine in Queensland, provides semi-quantitative information to assist decision makers when designating investment for minimising vulnerability of mining operations to climate. Here we present the processes involved in this three-step approach that uses pre-existing spatial data of the mine site and local knowledge to build a set of visual tools to assist decision-making. The first step of the process is performing multi-criteria evaluation (MCE) within a geographic information system (GIS) on ranked natural conditions at the mine, such as elevation, slope, drainage, soil and vegetation, which is performed to identify critical flood areas. Secondly, a fault-tree analysis identifies how impact can occur and what options there are for impact reduction. Finally, a resource assessment of the mineÆs capacity to adapt reduces the adaptation options to those most suited to the mine. The results are confidential, but for the purpose of introducing the methodology, we present simplified results, particularly of steps 2 and 3. CRATER can also be used for future æwhat-ifÆ flooding scenarios to identify the most suitable locations for roads, buildings or other critical infrastructure. The methodology is transferable to any mine, series of mines or locations along the mining value chain that have sufficient data, providing a practical decision-making tool to identify æno-regretsÆ actions that not only could reduce downtime after or during an event, but in some cases may enhance production between extreme events. We now plan to test this method at a broader scale, to encompass more than one mine in the analysis.CITATION:Hodgkinson, J H, Grigorescu, M and Alehossein, H, 2013. Climate Related Adaptation from Terrain Evaluation Results (CRATER) - interpretation of pre-existing data for mine site flood vulnerability and management, in Proceedings Water in Mining 2013 , pp 259-266 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By J L. Stacey

The diverse priorities, drivers and concerns of multiple stakeholders in the minerals industry complicate the integration of sustainable development considerations into mine design, as well as operational and strategic decisions. The ability of the industry to address all role-playersÆ needs, or indeed, to achieve consensus among all role players on the plethora of sustainable development issues seems a noble yet unattainable goal. One of the difficulties in assessing the relative importance of sustainable development issues across many stakeholders is the inevitable lack of impartiality in valuing these issues. Starting from a premise that transparency and fairness of the process are absolute prerequisites for progress, but that consensus is not, an approach has been developed in which all stakeholders are asked to assess the importance of all other stakeholdersÆ priorities, excluding their own. The approach recognises that stakeholders have different levels of contribution, understanding, vested interests, and perceptions of legitimacy and entitlement, across the diversity of sustainable development issues and decision criteria. Using Triangular Value Analysis, the relative weightings of each of the stakeholderÆs priorities are determined through a regression-like technique. The uniqueness of this approach is the manner in which self-assessment bias and overemphasis of stakeholdersÆ own priorities are avoided. The methodology can be used for both internal and external stakeholders, and in conjunction with other group decision making techniques, such as the nominal group or Delphi techniques. This paper will illustrate how Triangular Value Analysis may be applied in the minerals industry to determine priorities in various decisions relating to potentially conflicting sustainable development priorities within the industry.

Jan 1, 2009

By BTrubT M

In the roast-leach-electrolysis process for the production of zinc, iron contained in zinc concentrates is converted to zinc ferrite during roasting. At Canadian Electrolytic Zinc (CEZinc), the Outokumpu Conversion process is used to simultaneously leach zinc ferrite and precipitate the iron as jarosite. These simultaneous reactions, while providing good process stability, require a compromise between optimum conditions for maximum zinc extraction and efficient iron precipitation. An improved conversion process has been identified which can achieve >99 per cent zinc extraction and more efficient jarosite precipitation to residual iron concentrations of

Jan 1, 1993

By T Bookless, J Pownell, D Meadows

The ever increasing trend of the gold price has meant that ore deposits that were previously considered too complex, or unattractive by virtue of their low gold grade, are now being investigated more closely. These ore deposits present a greater risk of failure than previously was the case. To ensure that the risk of project failure is reduced and the maximum value is derived from the deposit, its mineralogy, as well as other characteristics, should be well understood such that the optimum process can be designed.Quite often the flow sheet design is assembled using individual process components, from various sources, and without consideration of the complete system. Test work programs require careful planning and an open viewpoint in terms of comminution circuit design particularly with respect to ever increasing power costs across the globe. As an example, high pressure grinding roll (HPGR) technology in many cases offers better mineral liberation than the more traditional comminution devices and it does so at a reduced energy input, and yet HPGR test work is often restricted in its scope due to the perceived novelty of the technology and the resultant lack of generally agreed and accepted test work routes.In this paper the authors outline a typical HPGR test work process route driven by the needs of different ore types and illustrate that to optimise the project value, any test work program should start from the premise that thorough understanding of the ore is vital.CITATION:Bookless, T, Meadows, D and Pownell, J, 2013. Enhancing project value through a designed high pressure grinding roll test work program, in Proceedings World Gold 2013 , pp 291-300 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

This paper describes a detailed geostatistical study of producing copper orebodies at Mount Isa Mines Limited in Queensland, Australia. As a result of this work, kriging has been adopted for grade estimation for final stope design at Isa Mine. Extensive variogram and back analysis studies indicate that one relative variogram model can be used to give optimal kriged grade estimates from production sampling throughout the 100 million tonne copper orebody complex. The kriging method replaces a computer technique used at [sa Mine based on inverse distance weighting using parameters chosen from experience.Comparative stope designs based on 10 million tonnes of ore indicate a 16% increase in minable ore tonnage at a grade well above the cut-off, as a result of the geostatistical work.Although this paper is written as a practical description with simple explanations of geostatistical concepts, the theory and use of relative variograms has been expanded. A possible link is suggested between relative variograms and first order kinetics of natural mineral concentration processes.

Jan 1, 1982

By B Darlington, L Sandberg, O Vallati

The D47 and D39 Mechanical Dynamic Extra bolts (D47 MDX and D39 MDX) have been developed in response to the ever-increasing demand from the mining industry for rock bolts with high dynamic capacity. To prove such capacity, Sandvik has performed numerous in situ dynamic testing with the unique Dynamic Test Rig (DTR) (Darlington, Rataj and Roach, 2019; Roach, Rataj and Darlington, 2019). To complement the collection of testing data, Sandvik, in collaboration with the Swedish Research Institute for Mining, Metallurgy and Materials (Swerim) have performed additional experiments in laboratory condition using Swerim’s new drop test rig. This rig utilises a momentum transfer method to apply a dynamic load to the bolt. The sample falls together with the mass until the support beam impacts stationary dampers and the momentum energy is transferred to the bolt. Part of the charged energy is released by the dumpers while the remaining portion is absorbed by plastic deformation and/or displacement of the ground support element. The D47 and D39 MDX bolts have been tested at Swerim’s test facility with different levels of input energy. Six tests were performed at the specification energy of 36 kJ and six tests were carried out with the maximum allowable energy from the facility, ie 44 kJ. The bolts confirmed their dynamic performance absorbing the input energy without failure. The D47 MDX bolt absorbed up to 33 kJ with 150 mm displacement while the D39 MDX bolt absorbed up to 35 kJ with 162 mm displacement. This work will present an overview of the drop test rig at Swerim’s facility and a collection of results of the test performed on the D47 and D39 MDX bolts. The test method and results will be analysed and compared to the tests carried out with the in situ DTR.

Nov 29, 2022

By M Ind, B Usher

Environmental regulators are increasingly adopting risk-based approaches to protect aquatic ecosystems. The Australian and New Zealand Environment and Conservation Council (ANZECC) and the Agriculture and Resource Management Council of Australia and New Zealand (ARMCANZ) (2000) introduced a risk-based approach to water quality guidelines that use decision frameworks to adapt water quality guidelines to local environmental conditions. Environmental quality objectives are no longer a simple ‘pass or fail’ number such as restricting total suspended solids (TSS) concentration to a specified limit for a particular rainfall event. This approach ignores spatial and temporal variability and the complexity of aquatic ecosystems. The risk-based approach establishes levels where adverse effects may occur. If these objectives are not met, further risk-based investigation is undertaken to assess the potential impact to the ecosystem. Klohn Crippen Berger (KCB) developed a dynamic simulation to predict the variability of sediment discharges, which is applicable for risk-based impact assessment of aquatic ecosystems. The application of the methodology over the life of a mine site is illustrated using a proposed South Pacific mine.The site location is in extremely rugged terrain with a high annual rainfall of approximately 4.7 m. There were two major sediment ponds proposed to reduce sediment discharges. A sediment and hydrology model was developed in Goldsim to provide daily estimates of run-off flows and sediment concentrations. A modified algorithm based on the Australian water balance model was created and incorporated into the Goldsim model and calibrated using recorded field data.The sediment module was developed based on a Revised Universal Soil Loss Equation (RUSLE) assessment, an annual prediction of soil loss over a catchment. A land-use type erosion vector was developed for different land-use types and for each of the subcatchments, a subcatchment erodibility vector was calculated. This vector and the daily rainfall erosivity factor were used to estimate the daily soil loss. The estimated soil loss and the modelled run-off yielded predictions of daily sediment concentrations. Finally, a sediment settling module was used to predict the daily efficiency of the sediment ponds and hence discharged sediment concentrations.The results of this modelling form the first part of a quantitative risk-based assessment into suspended solids impacts. The second part is the assessment of the effects of these predicted TSS concentrations on aquatic ecology. As part of the feedback-loop required in a risk management framework, if the environmental quality objectives are not met then further management decisions and actions may be required to reduce the risks presented by suspended solids. This may include modifications to: the mine-development plan; construction techniques and scheduling; processing techniques; rehabilitation strategies; or hard-engineering solutions such as sediment basins or flocculation.The Goldsim water-balance model provides a quick and efficient method of testing potential remedial actions on predicted sediment loads and concentrations. In combination with a cost-benefit assessment, options for reducing sediment releases from the mine site can be effectively and quantitatively compared thereby providing mine operators with a basis for decision-making. Regulators can also be satisfied that potential impacts to aquatic ecology have been comprehensively assessed and the necessary management decisions have been initiated to limit risk to the environment.CITATION:Ind, M and Usher, B, ?2014. A dynamic sediment simulation to predict the variability of suspended solids concentrations over life-of-mine for application to a risk-based environmental assessment, in Proceedings Life-of-Mine 2014 , pp 191–204 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

Carbon sequestration in planted forests provides an immediately available, low cost option to address the greenhouse impacts of coal mining and coal utilisation in a carbon constrained world. In addition, planted forests also offer the opportunity to address other environmental issues, particularly salinity and loss of biodiversity. Given salinity is characteristically associated with agriculture in the 500 to 700 mm rainfall belt, then where such forests can also produce commercial timber products, they offer the additional opportunity to establish new, diversified rural employment in both timber growing and processing. In the majority of Australian catchments affected by salinity, where rainfall is generally less than the 700 mm limit to conventional forestry, and where groundwater reserves are often saline, the objective of achieving economically viable forestry production presents a significant challenge. In 1996, Saltgrow commenced a collaborative breeding program to combine the salt and stress tolerance of E camaldulensis, with the growth rate, stem form and wood properties of the commercial species, E grandis and E globules. This program aimed to produce trees with the potential for commercial rehabilitation of saline landscapes. Results covering a range of site conditions from SaltgrowÆs network of over 100 trials around Australia are presented. The opportunity for commercial plantations integrated with agriculture in low to medium rainfall areas to address salinity and sustainability will be discussed. In addition, the significant potential for partnerships between land-rich, cash-poor farmers, catchment management authorities seeking to invest in public good projects that enhance environmental sustainability, and major carbon producing industries with either mandated or voluntary requirements to curtail net emissions will also be discussed.

Jan 1, 2005

The phosphatic overburden of Christmas Island is a lateritic soil and consists dominantly of crandallite and millisite. These minerals are polymorphs of general formula, (Na,K)x Ca2-x (Al, Fe)6 (PO4)4 (OH)10-x (2+x) H2O. Iron occurs only in millisite. Both minerals exhibit similar thermal transformations, dehydroxylating near 600¦C and recrystallizing above 800¦C. Dehydroxylation results in crystal structure collapse but retention of crystal morphology. Ggethite, boehmite and apatite are minor constituents of some-of the phosphatic Soils.

Jan 1, 1971

The Broken Hill Proprietary Company Limited (BHP) started as a silver-lead-zinc mining company in Broken Hill, New South Wales, Australia in the 1880s. Since then it has diversified into the resource industries of steel, iron ore, coal, petroleum and copper. BHP World Minerals is a Business Group of BHP which is one of the worldÆs largest and most diverse mineral resource enterprises. BHP supplies raw materials for steelmaking, copper concentrate and other mineral commodities to customers in more than 45 countries. BHP World Minerals has operations spread throughout the world û in Australia, the United States, Brazil, Zimbabwe and Canada. Commodities produced by BHP World Minerals currently include silver, lead, zinc, titanium minerals, platinum group metals and coal. The BHP World Minerals Cannington silver-lead-zinc mine in Queensland, Australia is a return to the cradle of BHPÆs early silver-lead-zinc years. This paper compares the success factors and challenges at Broken Hill and Cannington.

Jan 1, 1998

By A Tang, K Ringwood

"Water is increasingly being recognised as a material business risk that many companies are still not well-equipped to deal with. Despite a raft of water-risk focused initiatives, methodologies and guidelines, the challenge of managing the strong link between the technical and operational water issues, along with the growing external challenges and interests in water, remain a significant risk to a companyÆs ability to deliver value.This paper provides an overview of the key lessons learnt from ERMÆs experience of working with companies across a range of water sensitive industry sectors, in particular, the mining and oil and gas sectors, to develop and implement practical approaches to manage business critical water risk. These examples highlight the importance of managing water risk by linking technical and operational aspects of water management - with the longer term strategic and social license aspects. Four key ingredients were identified that are central to providing companies with a leading edge in the successful mitigation of water risk: understanding and evaluating water risk including the technical and operational aspects of water management, plus the longer term strategic and social aspects articulating a strong business case that prioritises water risks and their financial exposure to the organisation constructing a clear roadmap that practically links the water strategy objectives with on-the-ground implementation and action building capacity in the organisation to manage, engage and coordinate on water to mitigate risk.CITATION:Ringwood, K and Tang, A, 2013. Practical approaches to managing business critical water risk, in Proceedings Water in Mining 2013, pp 293-300 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 26, 2013

By Tien J. C

Many factors (type of coal mined, water pump pressure, wetting agent concentration, etc) will affect the performance of a dust suppression system using a water spray in an underground coal mine. While a two-level factorial method is useful in

Jan 1, 1994

By S K. Schwank

Trench cutter systems have been used in civil engineering for the least 30 years for the installation of deep cut-off walls, retaining walls and foundation systems. The systems are constantly advanced to achieve greater depth, penetrate through harder rocks a provide a bigger footprint of the cutter. The state-of-the-art equipment can reach down to 250 m vertical depth and penetrate all different types of soils and rocks up to 150 MPa unconfined compressive strength.In mining, especially in commodities with a high value and where the ore deposit has a small footprint, cutter mining with vertical attack from the existing ground level will be a new, cost-efficient approach where conventional open pit mining is not economically feasible due to a high stripping ratio. The same applies for open pit mines that have reached the end of their conventional mine life and where going underground is also uneconomical. The BAUER Cutter Mining System, which has been adapted to the special needs of mining, is a new technology that will allow mining at depths of up to 250 m.The same system can be also applied to ore dykes, be it vertical or slightly inclined, concentrating the excavation on the actual orebody and minimising the strip ratio and the contamination of ore. The system can be adapted to the dimension of the dykes or veins and to the rock conditions.BAUER’s latest approach is to use the vertical cutter mining technology for the extraction of sea floor massive sulfides from the seabed in deep ocean waters. Due to the compact footprint of the system and the vertical attack for mining, extraction of the ore can be concentrated on the hot spots, minimising the environmental impact on the sea floor both for mining and manoeuvring the remote-controlled mining tool.CITATION:Schwank, S K, 2015. Cutter mining – crossover technology from civil engineering to mining, in Proceedings Third International Future Mining Conference, pp 95–100 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015