Search Documents

By Howard R. Hume, Terry R. West, William R. Judd

One of the outcomes of a sector slope design in a large open pit in the western United States has been the scrutiny of the structural domain concept. These domains essentially define the area of influence of particular structural characteristics. In the present instance these structural characteristics are joint discontinuities. One of the major drawbacks of defining a domain is that unless large quantities of discontinuity data are available this process of definition is largely qualitative in nature. Viewed from a discontinuity analysis aspect the orientations of all the major joint sets at a given point are a concise descriptor of the structural geologic regime at that location. This is important to domain boundary definition, this in turn is extremely important for assigning which joint sets to use as input for slope stability analysis in a given discontinuity domain. An attempt has been made to develop a quantitative method for defining these discontinuity domains based on limited amounts of orientation data thereby reducing the subjectivity normally involved in such operations. Subjectivity is not always a problem if large quantities of joint orientation data are available, since the mean and variance of joint clusters always can be compared and then grouped to define these domains. However, even this method suffers from the problem that only a single joint set orientation can be considered at a time during the grouping process. On the other hand a discontinuity domain requires that all joint sets at a point be considered simultaneously to truly define the structural discontinuity character of that point. This provides a far more complete

Jan 1, 1982

By N. De Nevers

A calculation method has been developed for carbonated water flooding. This method takes into account the effects of oil viscosity reduction and oil swelling, due to carbon dioxide transferred to the reservoir oil from the carbonated flood water. It shows the effect of changes in carbonation pressure and carbonated water slug size. The method is based on a Buckley-Leverett-type linear flow model. The mathematical approach is similar to that developed by Welge, et al, for enriched gas drives. However, it contains a very important advance over the previous papers in its solution to the problem of injection of a "slug" of carbonated water rather than continuous injection of fluid of constant composition. The method also shows the chromatographic nature of the transport of Co 2 in a carbonated water flood. Sample calculations indicate that viscosity reduction is the most important source of incremental oil recovery. Swelling contributes to a lesser extent. Raising the carbonation pressure increases recovery, but this effect diminishes as pressure is increased. increasing the slug size also increases recovery, but again this effect diminishes as slug size is increased. INTRODUCTION In recent years there has been considerable interest in carbonated water flooding as a secondary recovery method. Several carbonated waterflood field tests are now in progress.1'3 Yet there is no published method for predicting the results of a carbonated water flood. This paper presents a method for predicting the oil recovery for ; carbonated water flood. In a carbonated water flood. a carbonated water slug is injected into the reservoir. Then this slug is driven forward by injecting plain water behind it. The field operator must choose the carbonated water slug size and the CO2:water ratio in the slug. The calculation method presented here shows the effects of both slug size and CO2:water ratio on oil recovery. The calculation assumes that the addition of carbon dioxide to flood water increases the oil recovery by two mechanisms: 1. Carbon dioxide transfers from the flood water to the oil, thereby reducing the viscosity of the oil. At the lower viscosity, the oil flows more readily and is more easily swept out by flood water. 2. The carbon dioxide which transfers to the oil phase causes the oil phase to swell. Assume that the residual oil saturation (volume per cent of pore space) is the same whether the oil is carbonated or not. Then the same volume will contain less stock tank oil if it is carbonated, due to oil swelling. The plain water driving the carbonated water slug forward will strip the CO2 out of this residual oil., causing this oil to shrink. This swelling-followed-by-shrinking leaves behind a lower residual oil saturation than would have been left behind by a plain water flood. Since some oils swell to almost twice their original volume at reasonable CO2 pressures, this effect may be large. Two additional benefits sometimes claimed for carbonated water flooding are: 1. Adding CO2 to flood water greatly increases the water injectivity in some cases.1 (Injectivity = BPD of water injected/ft of sand x differential bottom-hole pressure, psi.) CO2 forms a weak acid in water; injecting carbonated water is, therefore, somewhat like acid treating. If a formation responds to acid treating, it will probably have a higher injectivity for carbonated water than for plain water. Although the increased injectivity increases the profitability of a carbonated water flood over a plain water flood, it does not change the production curve based on total fluid injected. Therefore, the method presented here does not show any effect of increased injectivity. 2. It is claimed in one patent4 that carbon dioxide will react with some constituents of the oil to form detergents. These detergents are expected to increase the oil recovery. There is little data available to support this idea. The calculation method presented here takes no credit for extra oil recovery due to the formation of any such detergents.

Jan 1, 1965

By G. S. Phipps, E. E. Schumacher, G. M. Bouton

THE seriousness of the present tin scarcity has stimulated large consumers of this vital metal to develop drastic conservation measures in order to extend the available supplies to cover the emergency period. By devising new soldering methods and alloys the Bell System has contributed a substantial share in the tin conservation effort, Fortunately, the changes, as far as can be determined now, have not introduced weakness into the soldered joints. Some of the new procedures were already in the process of development at the onset of the emergency, while others were devised under its stress. In some instances, the newly developed solders were found to be more difficult to use than the alloys previously available, and would not have been introduced under normal conditions. One major change made that previously had been under consideration will result in large savings of tin. Unless service difficulties are encountered, this modification gives promise of remaining after the emergency has passed. The change involves a reduction in the amount of solder placed on a wiped joint between the cable sheath and the sleeve. Instead of the customary full sized wiped joint, a wipe of fillet proportions is formed. Through this change, a solder saving of more than 60 per cent per joint can be realized. Plumbers and cable splicers for many years have joined lead pipes and cable sheath by a soldering process called "wiping." The name is an apt description of the operation. For a wiped joint, the sections to be united' are heated by molten solder poured over their surfaces, and the resulting semiliquid mass is manipulated by wiping with cloth pads to a well rounded symmetrical form like the one shown in Fig. I, The operation requires considerable skill on the part of the splicer and close control of the composition of the solder. At first consideration, the problem of tightness in such joints seems simple but experience shows that even under the best conditions the fissures frequently found in the solder occasionally link and form a path that allows leakage to occur. In telephone cables not maintained under gas pressure, such leaks permit the entrance of water, which wets the paper-covered conductors and thereby impairs the insulation value and causes service interruptions. By going to an extreme and wiping off all the solder in excess. of a fillet, it has been found that many causes of porosity are eliminated. Figs. 2 and 3 show cross sections of joints wiped in the old and the new ways. The saving in solder, and consequently in strategic tin, is evident. The field splicing forces find that joints are easier to make by the new method and are less likely to be porous. The metallurgical considerations that are responsible for the success of the fillet wipe are of interest. Much has been written about the wiping process of soldering cable joints and the many requirements of a good wiping solder have frequently been listed. The success of the procedure described

Jan 1, 1943

By John C. F. Randolph

This establishment being now in full working order, it has seemed of considerable professional interest to collect together, in a concise form, the various points as to its plan, method of dressing, and equipment. The data contained in this paper have been largely drawn from the able paper of E. Kutscher, constrnoting engineer of the works, contained in the Zeitschrift fur Berg-HÜtten-und Salinenwesen im Preussischen Staate, 1873, supplemented by some personal memoranda made while the works were under construction and by memoranda on the works appearing in various German technical papers from their completion up to date. This is probably the largest dressing works in the world devoted to the beneficiation of argentiferous lead ores, and it is doubtful if any establishment for the concentration of mineral of any description can compare with it in size. As showing the final practice adopted in an old and very conservative mining region, in which the concentration of ores has been a matter of constant practice and experiment for a very long period, these works are of peculiar interest. The fact that the Clausthal ores strongly resemble a very large and abundant class of ores found in the United States has always attracted the attention of American mining engineers and mine owners to the methods employed in dressing and smelting them. The study of their methods of concentration of ores has, however, always been full of difficulty,

Jan 1, 1879

By H. M. Chance

In almost all coal-fields, the quantity of explosive gases given off by the coal increases as depth is attained, requiring correspondingly enlarged quantities of air to ventilate the workings properly, by diluting and carrying off the gas. Again, with increased depth there is a corresponding increased pressure caused by the weight of the overlying strata. Sandstone or slate, which would form a good roof for a coalbed at a depth of 300 or 400 feet, may be unable to sustain the pressure of 800 or 1000 feet of overlying rock. Hence, in nearly all deep mines, the miner will generally describe the roof as "bad," although the roof-rock may be a firm slate, forming an excellent roof for workings of moderate depth, but unable to stand the pressure resulting from the weight of a great thickness of overlying rock. With increased weight of rock-mass above comes also

Jan 1, 1901

By T. Okubo

Gold is generally recovered from silver anode slime by electrolysis in the final step of the copper anode slime treatment. In the present investigation, rapid and direct hydrometallurgical separation and recovery of gold in the early step of the process is studied. Gold is recovered just after the elimination of copper and selenium from copper anode slime. The studied process consists of: (a) oxidizing roasting for selenium elimination, (b) sulfuric acid leaching of the calcine for copper removal, reduction of gold in the liquor by the use of proper reductant such as hydrogen peroxide (production of gold powder), (el nitric acid treatment of gold powder for further purification and (f) melting and casting of gold. Laboratory and miniplant testwork showed that the extraction ratio of gold by chlorine leaching was 99 % up and four nine gold ingot could be recovered without electrolyses.

Jan 1, 1984

By E. E. Schumacher, G. S. Phipps, H. M. Bouton

The seriousness of the present tin scarcity has stimulated large consumers of this vital metal to develop drastic conservation measures in order to extend the available supplies to cover the emergency period. By devising new soldering methods and alloys the Bell System has contributed a substantial share in the tin conservation effort. Fortunately, the changes, as far as can be determined now, have not introduced weakness into the soldered joints. Some of the new procedurcs were already in the process of development at the onset of the emergency, while others were devised under its stress. In some instances, the newly developed solders were found to be more difficult to use than the alloys previously available, and would not have been introduced under normal conditions. One major change made that previously had been under consideration will result in large savings of tin. Unless service difficulties are encountered, this modification gives promise of remaining after the emergency has passed. The change involves a reduction in the amount of solder placed on a wiped joint between the cable sheath and the sleeve. Instead of the customary full sized wiped joint, a wipe of fillet proportions is formed. Through this change, a solder saving of more than 60 per cent per joint can be realized. Plumbers and cable splicers for many years have joined lead pipes and cable sheath by a soldering process called " wiping." The name is an apt description of the operation. For a wiped joint, the sections to be united are heated by molten solder poured over their surfaces, and the resulting semiliquid mass is manipulated by wiping with cloth pads to a well rounded symmetrical form like the one shown in Fig. I. The operation requires considerable skill on the part of the splicer and close control of the composition of the solder. At first consideration, the problem of tightness in such joints seems simple but experience shows that even under the best conditions the fissures frequently found in the solder occasionally link and form a path that allows leakage to occur. In telephone cables not maintained under gas pressure, such leaks permit the entrance of water, which wets the paper-covered conductors and thereby impairs the insulation value and causes service interruptions. Ry going to an extreme and wiping off all the solder in excess of a fillet, it has been found that many causes of porosity are eliminated. Figs. 2 and 3 show cross sections of joints wiped in the old and the new ways. The saving in solder, and consequently in strategic tin, is evident. The field splicing forces find that joints are easier to make by the new method and are less likely to be porous. The metallurgical considerations that are responsible for the success of the fillet wipe are of interest. Much has been written about the wiping process of soldering cable joints and the many requirements of a good wiping solder have frequently been listed. The success of the procedure described

Jan 1, 1943

By H. M. Bouton, G. S. Phipps, E. E. Schumacher

The seriousness of the present tin scarcity has stimulated large consumers of this vital metal to develop drastic conservation measures in order to extend the available supplies to cover the emergency period. By devising new soldering methods and alloys the Bell System has contributed a substantial share in the tin conservation effort. Fortunately, the changes, as far as can be determined now, have not introduced weakness into the soldered joints. Some of the new procedurcs were already in the process of development at the onset of the emergency, while others were devised under its stress. In some instances, the newly developed solders were found to be more difficult to use than the alloys previously available, and would not have been introduced under normal conditions. One major change made that previously had been under consideration will result in large savings of tin. Unless service difficulties are encountered, this modification gives promise of remaining after the emergency has passed. The change involves a reduction in the amount of solder placed on a wiped joint between the cable sheath and the sleeve. Instead of the customary full sized wiped joint, a wipe of fillet proportions is formed. Through this change, a solder saving of more than 60 per cent per joint can be realized. Plumbers and cable splicers for many years have joined lead pipes and cable sheath by a soldering process called " wiping." The name is an apt description of the operation. For a wiped joint, the sections to be united are heated by molten solder poured over their surfaces, and the resulting semiliquid mass is manipulated by wiping with cloth pads to a well rounded symmetrical form like the one shown in Fig. I. The operation requires considerable skill on the part of the splicer and close control of the composition of the solder. At first consideration, the problem of tightness in such joints seems simple but experience shows that even under the best conditions the fissures frequently found in the solder occasionally link and form a path that allows leakage to occur. In telephone cables not maintained under gas pressure, such leaks permit the entrance of water, which wets the paper-covered conductors and thereby impairs the insulation value and causes service interruptions. Ry going to an extreme and wiping off all the solder in excess of a fillet, it has been found that many causes of porosity are eliminated. Figs. 2 and 3 show cross sections of joints wiped in the old and the new ways. The saving in solder, and consequently in strategic tin, is evident. The field splicing forces find that joints are easier to make by the new method and are less likely to be porous. The metallurgical considerations that are responsible for the success of the fillet wipe are of interest. Much has been written about the wiping process of soldering cable joints and the many requirements of a good wiping solder have frequently been listed. The success of the procedure described

Jan 1, 1943

By Ernest Stütz

(New York Meeting, October, 1913.) THE problem of increasing blast-furnace efficiency through diminution of flue-dust production while operating with burdens consisting largely of fine ores has of recent years attracted the attention of metallurgists, whether directly or indirectly interested in the economies of iron smelting, and the various methods evolved from theory or practice have been. submitted to wide discussion. After the very thorough and, at that time, exhaustive view of the whole subject, which was afforded to the industry by the meeting of this Institute in February, 1912, the subject was again taken up at the meeting of the Verein deutscher Eisenhüttenleute at Düsseldorf in December, 1912. While American and German conditions are not entirely identical, it may be of interest to give here the words of the gentleman summing up the discussion at the Düsseldorf meeting : ?The chief advantage offered by the use of briquettes lies in the fact that disturbances in the furnace, caused mostly by the presence of fine ores in the burden, are avoided, and that blast pressure can be considerably reduced. The resulting economies cannot be overrated, as, with lower blast consumption per ton of product, the installation will be able to take care of increased production. In consequence of lower pressure and speed of blast, heat is more efficiently utilized,, flue gas temperature is lowered, and coke particles are less liable to be carried along with the flue dust, of which considerably less is produced. Finally, by increased regularity of operation and higher temperature in the lower parts of the furnace, the quality of the product is improved. The question of briquetting iron ores has grown to be one of the most important in the iron industry, and it is not any more a question of what is the cost 'of briquetting a ton of ore, but what, in. using ore briquettes, is the cost, of: production of a ton of iron."

Jan 7, 1913

By F. C. Schora, H. P. Meissner

Both a graphical and an analytical technique are presented for calculating stream compositions and temperatures in adiabatic staged systems in which solids travel countercurrently to a gas stream. Such a system might be a tower containing several plates, on each of which the descending solid is fluidized by the rising gas stream. Examples are presented in which chemical reactions occur, including the oxidation of SO, by a solid catalyst and the gaseous reduction of iron oxides. COUNTERCURRENT staged processes involving reactions between solid and gas streams are becoming more common. These operations are generally carried out in a series of beds of fluidized solids, with each bed or "plate" acting as a stage. Fig. 1 is a schematic diagram of such a series of stages located in a column, down through which a solids stream moves from stage to stage counter to a rising gas stream. Typical reactions carried out in such systems are the dehydration of aluminum trihydrate, the calcining of limestone, and the gaseous reduction of iron oxides. Calculation of the performance of these counter-current systems rapidly becomes more complex with increases in the number of stages and in the number of chemical reactions occurring. Calcula-tional procedures for isothermal operations of such systems have been described.4 Actual tower operations, however, are generally adiabatic, and in consequence far from isothermal. The object here is to present both graphical and analytical techniques applicable to such adiabatic towers operating continuously and in steady state. In this introductory discussion, the graphical techniques presented are of the McCabe-Thiele type, rather than of the Pon-chon type. In all the examples presented, it will be assumed that both thermal and chemical equilibrium are attained in each bed. The assumption that the gas and solid streams leaving each bed are at the same temperature as the bed is in accordance with the familiar behavior of actual fluidized solid systems. Chemical equilibrium, on the other hand, is not necessarily attained in any given stage between these two streams, even with deep beds, since reaction rates may be slow. In the last section of this paper, discussion is presented of methods suitable for use when chemical equilibrium is not attained. The adiabatic tower in Fig. 1 has "n" stages numbered from 1 to n, starting with the bottom stage as number 1. In analyzing this tower's performance, it is important to express gas flow rates in terms of a key component or element which remains completely within the gas stream throughout the tower. Similarly, solid flow is best expressed in terms of a key compound or element which remains within the solid phase throughout the tower. Thus, in burning limestone with a hot flue gas, the gas flow might be expressed as G, the pound mols of nitrogen flowing through the tower per unit time, while solid flow might be expressed as S, the pound atoms of calcium in all forms in the solid stream per unit of time. Defined in this way, both G and S are constant throughout the tower. The enthalpy of the gas and solid streams are now best expressed in terms of these key components. That is, the gas stream enthalpy H is expressed as Btu in the total gas per mol of the key component in the gas. Similarly, the solids stream enthalpy h is expressed as Btu in the total solid stream per pound mol (or pound atom) of the key component in this stream.

Jan 1, 1962

By C. H. Jr. Herty

FEW subjects have attracted the attention of metallurgists more than ,oxygen in steel. From the days of Mushet and Ledebur interest in this subject has been increasing, and as additional knowledge has become available, the problem has naturally grown more complex. Instead of using the simple term "oxygen" we now distinguish between iron oxide, silicates of various kinds, oxysulfides, oxygen as gas and oxygen in solid solution in steel. There are five general methods for determining oxides in steel: hydrogen reduction;, vacuum fusion; various wet-extraction methods, including electrolytic methods; methods depending on volatilization of the iron away from the oxides; and metallographic methods. For oxygen in solid steel each of these methods has both advantages and disadvantages. The hydrogen-reduction method is of no use on steels above about 0.20 per cent. carbon;1 furthermore, it gives only FeO and possibly some MnO. The vacuum-fusion method2 is expensive and gives total oxygen, with the exception of some A1203, and does not differentiate between the various oxides in which the oxygen exists. Most of the wet-extraction methods' give only the more insoluble oxides Si02 and A1203, though the iodine method gives MnO to an uncertain degree (information that may be more misleading then no information

Jan 1, 1930

By A Allen, J. A. Garcia

The large increase in the wages of mine workers makes it imperative that all factors tending to limit production per miner be eliminated, if possible. The trolley and storage-battery locomotive, mining machine, hoisting engine, mining system, etc., have increased the possible output per man. But this output is still limited by the capacity of the hoisting engine and cable and by the size of the mine car. The superiority of skip hoisting in metal mining is shown by its almost universal adoption. By varying the size of skip and the rope speed, any desired tonnage can be secured and, since frequently only one kind of material is handled and breakage is unimportant, the loading of the skips can be easily and cheaply effected from bins into which the cars are dumped. The cars may then be designed to fit the conditions in the mine instead of being a compromise between hoisting and mining conditions, very likely suiting neither. In coal mines, the usual practice has been to hoist the car to the surface, either on platform or self-dumping cages. Of late years the number of skip-hoisting plants in coal mines has been rapidly increasing, but there is more or less inertia to overcome in establishing so radical a change in practice; also the earlier skip operations were not uniformly successful. As a result, it became evident that metal-mining practice would require radical modification before skip hoisting could be successfully used in coal mining. Objections to Skip Hoisting Breakage Except where coal is used for coking, or for other purposes whcre breakage is unimportant, breakage of the coal is vitally important all the way from the face to the railroad car. The average selling price is seriously reduced when the percentage of screenings is increased. Following metal-mining practice exactly, the coal would be dumped into a deep pocket, cut off into a skip load by a measuring hopper or other means, dumped into a deep, narrow skip, and dropped into a bin at the top, all of which would contribute to excessive breakage.

Jan 1, 1922

By J. W. Leonard, B. A. Donahue

A method is described for incorporating coal petrography into mining and preparation plant quality control based on conventional analyses. Complete analyses are made of each of the uniform and relatively distinct petrographic bands in a coal face. With this information it is possible to develop petrographic standardization curves. These curves permit diverse coal characteristics to be rapidly monitored by application of a few standard coal tests. Single seam quality control is discussed in this paper. Inquiries continue to be made about coal petrography, and specifically, about whether coal petrography should be applied more extensively in the coal industry. Coal petrography is the study of the distinct physical, optical, and chemical increments which make up the organic rock mixture which we know as coal. Petrography can be applied by any coal company or at any coal mine where conventional coal analytical facilities are available and where additional resources can be allocated for an increased number of determinations. This first paper of a two part series includes (1) a proposed conventional approach to single seam petrography based on the development of petrographic standardization graphs and (2) some informative and supplemental interrelationships involving coal characteristics developed as a result of this research. In the second part of this series, to be published at a later date, those petrographic characteristics of bands taken from many different coal seams located over wide geographic areas which can be closely related to each other will be considered. These findings will be examined looking toward the development of a comprehensive, conventional approach to coal petrography which can be used as a common basis for multi-rank petrographic standardization graphs. Implicit to the understanding of coal petrography is the well established fact1,2 that the individual analyses of distinct petrographic bands often differ widely from the average analysis which is used to characterize a whole coal seam. In fact, a distinct and minor banded increment of coal in a high volatile seam may actually be a medium or low volatile coal with an analysis similar to the average analyses of seams located in distant coal fields. During the mining of coal, much degradation is caused which tends to randomly scatter coal bands. The degraded, scattered, and physically separated constituents of distinct petrographic bands are processed side by side in the coal preparation plant as distinct petrographic fractions with particles grouped according to a narrow size range (which derives in part from common hardness), specific gravity, and-or surface chemistry. Tile data obtained from numerous analyses made on each of the bands of any given coal seam, although diverse, can be readily interrelated. Indeed, these interrelationships can be developed into a series of nomographs or petrographic standardization graphs to serve as a basis for developing a conventional petrographic* program. Thus, by analyzing one property (for example, ash) of a selected petrographic fraction collected or separated from the flow of coal in a preparation plant, it should be possible to estimate the other physical, chemical, and thermal properties of this fraction by referring to the petrographic standardization graphs. It follows that any or all petrographic fractions in the total coal flow originating from a single coal seam can be rapidly monitored for many properties on the basis of a single analysis run on each fraction. In recent years coal petrographic research has concentrated heavily on that phase of this work which involves microscopic reflectance measurements made at many minute and selected points on a coal briquette surface.3,4 Thus, the percentage of the total number of reflectance measurements that fall into each of a consecutive series of arbitrarily chosen reflectance classes are used to characterize coal. This procedure is analagous to using the face of a coal briquette to represent the reflectance characteristics present at the face of a coal seam. Moreover, by analyzing petrographic fractions of known and uniform optical properties it is possible to closely relate reflectance to other coal characteristics. For example, reflectance has long been known to be related to such

Jan 1, 1968

By Tracy C. Jarrett

In 14-karat gold alloys, as in 10-karat gold alloys,3 the addition of such metals as zinc, nickel, copper and silver produces a wide range of physical and chemical properties such as color, hardness, corrosion resistance and melting points. These important factors made gold alloys desirable in the optical work and for jewelry. In 14-karat gold alloys, as well as in 10-karat or 12-karat, it is possible to have two golds of the same color, one of which will corrode more than the other, although it may be harder. Some of these alloys have been investigated by F. E. Carter,' E. M. Wise,= and L. Sterner Rainer.4 In this group of alloys the gold content of 58.3 per cent (14-karat) was held constant, while the copper varied from 36 to 24 per cent. The balance of the alloy consisted of one, two, or three of the metals silver, zinc, and nickel. All the alloys were melted in an induction furnace and cast into an ingot that measured 3 by 1/4 by 3/4 in. The method of determining the melting points, color determinations and acid test have been discussed in previous papers by the author.2, 3 It is necessary to use small test bars (Fig. I). The tensile bars were annealed at 1300oF. for 20 min. and then air-cooled. There being a very marked drop when the yield point was reached, "the drop of the beam" method was used in determining the yield point. Alloys Gold-copper.zilzc A~loys.—Gold-copper-zinc alloys melt, cast, and labricate easily. The low melting points, however, limit their use to some extent. The physical properties of these alloys are not entirely satisfactory. When the ultimate strength is satisfactory, the elongation and reduction of area are too low (Table I). Gold-copper-sinr-nickel A lloys.—In this group of alloys, in which zinc and nickel replace copper in approximately equal parts (Table I), the yield point, hardness, and ultimate strength increase with the increase of zinc and nickel content, while the reduction of area and elongation decrease. The physical properties are desirable, particularly of the white gold alloys. The alloys of this group are not difficult to cast and fabricate, and most of these colors could be used commercially. Gold-copper-nickel A lloys.—Gold-copper-nickel alloys are similar to the gold-copper-zinc and the gold-copper-zinc-nickel alloys. They do, however, possess high yield point, ultimate strength and hardness, somewhat higher than those of the other two groups mentioned (Table I). The difficulty with these alloys is that they fire-crack readily and heavy rolling is necessary between annealings. Being hard to fabricate, many

Jan 1, 1941

By Tracy C. Jarrett

In 14-karat gold alloys, as in 10-karat gold alloys,3 the addition of such metals as zinc, nickel, copper and silver produces a wide range of physical and chemical properties such as color, hardness, corrosion resistance and melting points. These important factors made gold alloys desirable in the optical work and for jewelry. In 14-karat gold alloys, as well as in 10-karat or 12-karat, it is possible to have two golds of the same color, one of which will corrode more than the other, although it may be harder. Some of these alloys have been investigated by F. E. Carter,' E. M. Wise,= and L. Sterner Rainer.4 In this group of alloys the gold content of 58.3 per cent (14-karat) was held constant, while the copper varied from 36 to 24 per cent. The balance of the alloy consisted of one, two, or three of the metals silver, zinc, and nickel. All the alloys were melted in an induction furnace and cast into an ingot that measured 3 by 1/4 by 3/4 in. The method of determining the melting points, color determinations and acid test have been discussed in previous papers by the author.2, 3 It is necessary to use small test bars (Fig. I). The tensile bars were annealed at 1300oF. for 20 min. and then air-cooled. There being a very marked drop when the yield point was reached, "the drop of the beam" method was used in determining the yield point. Alloys Gold-copper.zilzc A~loys.—Gold-copper-zinc alloys melt, cast, and labricate easily. The low melting points, however, limit their use to some extent. The physical properties of these alloys are not entirely satisfactory. When the ultimate strength is satisfactory, the elongation and reduction of area are too low (Table I). Gold-copper-sinr-nickel A lloys.—In this group of alloys, in which zinc and nickel replace copper in approximately equal parts (Table I), the yield point, hardness, and ultimate strength increase with the increase of zinc and nickel content, while the reduction of area and elongation decrease. The physical properties are desirable, particularly of the white gold alloys. The alloys of this group are not difficult to cast and fabricate, and most of these colors could be used commercially. Gold-copper-nickel A lloys.—Gold-copper-nickel alloys are similar to the gold-copper-zinc and the gold-copper-zinc-nickel alloys. They do, however, possess high yield point, ultimate strength and hardness, somewhat higher than those of the other two groups mentioned (Table I). The difficulty with these alloys is that they fire-crack readily and heavy rolling is necessary between annealings. Being hard to fabricate, many

Jan 1, 1941

By S. Stutz

Three years ago, at the Philadelphia meeting, in February, 1881, the author had the pleasure of presenting to the Institute a paper on coal-washing machinery.* Since that time many new machines, with important improvements and labor-saving apparatus, have been introduced, the construction and description of which may be of interest to some of the members of the Institute. By referring to the above-mentioned paper, and more especially to Plate IV., representing a vertical section of a coal-washer, it will be noticed that the bottom of the plunger-box B is made level or horizontal, and supports a spring-buffer F for the purpose of limiting the down-stroke of the plunger P and receiving the impacts of the latter. Althongh the construction of the box, in view of these impacts, received from the start the proper attention (the bottom of the chamber 3 being made of three thicknesses of 3-inch planks, resting on 6-inch sqnare columns), yet, through careless working of the machinery, without the necessary water in the box, it proved in several instances not strong enough, and had to be changed. To prevent such interruptions in future, it became necessary to devise some means for relieving the machine from the impacts of the plunger altogether. This has been accomplished by the arrangement shown upon Plate I. of this paper, representing a new waesher; and not only has the difficulty been overcome, but also sorne other advantages have been obtained, as will be seen further on. The compartments +, A' of the separator-box have been set upon heavy cast-iron brackets B, leaving sufficient space below the bottom for the buffer F and the sediment-valve K. By means of the plunger-rod 6 passing through the stuffing-box s to the outside, and provided at its lower end with a shoe a, the impacts of the plunger are now transmitted from the buffer F directly to the foundation. At the same time a better guide for the plunger P in its up and down movement has been obtained. The plunger of the former machine had only the guide I and the yoke Y, whereas the new machine has an additional guide in the stuffing-box s, thus preventing wear and friction of the plunger against the lining of the box. Further-

Jan 1, 1884

By Harry L. McNeill

THE Selective Media Process was developed by the author in a laboratory provided by The Steårns-Roger Manufacturing Co. It is the outcome of an [ ] investigation into the possibilities of coarse beneficiation by sink and float without using the conventional heavy media. Commercial work to date has been limited to the treatment of minus 3/8-in. iron ore at the Hill Trumbull washing plant of the Cleveland Cliffs Iron Co., at Calumet, Minnesota. Two cut away prints of the machine are shown (Figs. I and 2). A rotary conical impeller is mounted within a stationary cone (Fig. 2). This impeller is adjustable vertically by a 12-ton screw jack. The speed of the impeller can be varied from 14 to 32 r.p.m. by the Reeves variable-speed motor pulley mounted on the 7 ½ -hp. motor drive. Attached to the bottom of the stationary cone is the automatic control valve for sink product, actuated by a ¼ -hp. gear motor. The sink product is dewatered in a conventional drag driven by a 7 ½ -hp. motor and discharged onto an inclined conveyor containing from 6 to 10 per cent moisture. Two plants are operated at the Hill Trumbull property. All the ore is first treated in a typical washing plant (Fig. 3). When treating "wash ore" a finished concentrate can be produced by the log washers and Akins classifiers, as the separation involves only fine silica (minus 48-mesh) and free iron. However, when "jig ore" is fed to the washing plant the coarse

Jan 1, 1946

By Robert Warner

WHEN a new mine is opened, and often when an operating mine must adapt itself to physical or economic changes, a mining system must be selected in complete detail. In the past the plan chosen was usually the product of the local staff alone, however limited the training and experi-ence of that staff might be, which often resulted in the introduction of methods that were familiar to the staff, but not so well suited to the con-ditions as others unknown to the local men. A new management, noting the difficulties with the existing layout, might make modifications or complete changes, so that many mines in their history have seen a whole series of mining systems, each somewhat laboriously grafted on to its predecessor. This should not be interpreted as a condemnation of the older staffs for sticking to the tried systems, such as open square-sets in the early days at the Homestake, because they knew it would work after a fashion, nor does the statement apply to the technically trained, and usually broadly experienced staffs of most present-day properties. The older miners did not have the variety of tools and methods, nor the present freedom of transfer of information as to what the other man is doing, and so did the best they could under the circumstances. Finally, the higher grade of the ores made the choice less vital. The ever-increasing need to mine low-grade orebodies, with a fixed or even lower price for the metal produced, has caused an increasing need for low-cost mining. In most new mines this has simplified the problem of selection by eliminating from consideration all of the high-cost systems, but it has also complicated the choice by the necessity for refinement in detail and a close adjustment of the plan selected to all the conditions at the property. In these low-cost problems any textbook division of mining systems as applied to "beds, veins or masses" avails little as a guide. It should be realized at the outset that to' be successful under modern competitive conditions a system of mining must be worked out with elaborate detail, with careful time scheduling and control of the various elemental operations, and that after it is introduced it must be run with a large amount of technical direction.

Jan 1, 1933

By Fred C. Bond

It sometimes happens that old knowledge is forgotten, or half-forgotten, and its rediscovery is hailed as a great new advance in technology. Autogenous grinding affords such an example. The oldest-or apparently the oldest-commercial application of continuous autogenous grinding on a large scale outside of South Africa occurred at San Juancito, Honduras, where a total of more than two million tons of silver ore were ground autogenously with complete success from 1918 to the early 1940's. The history of the San Juancito silver deposits begins in 1880 when- the New York and Honduras Rosario Mining Co. started mining silver at a rate which soon reached two million ounces of silver annually. In 1912 the Company's first mill, located in the village of San Juancito, was shut down and its equipment transferred to a new cyanide plant. This plant, constructed on a mountainside near the mine, was equipped with tube pebble mills in which Normandy or Danish pebbles were used initially.

Jan 5, 1963

By G. B. Gould

FROM the very inception of the price-control experiment in the bituminous-coal industry, the problem of price differentials was of major importance. In fact, assuming that there will be no legal or Govern- mental obstacles to price control, the successful maintenance of the present or any other method designed to control bituminous-coal prices will depend upon the discovery of some satisfactory way to determine these differentials in price, among: individual mines and groups of mines. Being of organic origin, bituminous coal is a commodity that presents an almost infinite variety of qualities. It is inevitable, therefore, that a work- able price-control system must attempt

Jan 1, 1935