Search Documents

The suggestions of the members of the Institute are very much desired by-the Committee on Nominations prior to deciding upon its nominations to fill the places of those officers who retire early in 1917. The Committee must make its final report to the Board of Directors early ill October. The members are, therefore, -asked to send in promptly their suggestions for Directors as well as for Vice-Presidents and President. The Committee hopes to hear from a large number of the members. The officers to be elected at the annual meeting in February, 1917, are: One officer, known as Director and president. Two officers, known as Director and Vice-President. Five officers, known as Director. The attention of members is called to Articles V and VII of the Constitution, and to By-Law XIII, which reads as follows: "The geographical districts to be considered by the Committee on Nominations shall be as follows, until otherwise ordered by the Board. District No. 1. New England, New York, and New Jersey, excepting New York

Jan 9, 1916

By T. R. Ingraham

The thermal decomposition of cupric sulfate and of cupric oxysulfate has been examined by deter-mining the equilibrium gas pressure generated over each pure compound. The equilibrium data have been used to calculate the thermodynamic properties of both compounds, and the results have been combined with previously published data to establish a predominance-volume diagram for the Cu-S-O system over the normal range of roasting temperature and gas composition used in the treatment of copper minerals. Copper oxysulfate recrystal-lizes at 1100°K with an apparently irreversible en-dothermic heat requirement of 2.9 * 0.3 kcal per mole. WHEN mixed sulfide minerals containing copper are roasted, either of two procedures may be followed, depending on the nature of the other metals. In the first procedure, the roasting is controlled to produce a maximum amount of water-soluble copper sulfate which may be removed selectively from the water-insoluble compounds of the other metals. In the second, control is directed toward the production of water-soluble sulfates of the other metals and an insoluble salt of copper. Effective control of either of these processes would be enhanced by knowledge of the thermal stability of cupric sulfate and of cupric oxysulfate. In this paper, established data for the thermal stability of cuprous and cupric sulfide and of cuprous and cupric oxide will be combined with new data for the therma1 stability of cupric sulfate and cupric oxysulfate, to designate the volumes of stability of the significant compounds in the Cu-S-O system in the temperature range 750° to 950°K. EXPERIMENTAL Materials, Apparatus, and Procedure. The copper source material used in all experiments was Fisher Certified Reagent Grade "anhydrous" cupric sulfate, for which the following analysis was supplied by the manufacturer: chloride, 0.002 pct; alkalies and earths, 0.2 pct; insoluble, 0.002 pct; iron, 0.020 pct. Cupric oxysulfate was prepared from the normal sulfate by two procedures. In the first, equimolar quantities of cupric oxide (prepared by decomposition of the sulfate) and cupric sulfate were ground together and heated under vacuum in a sealed silica vessel at 800°C. This procedure was subject to failure because of explosion of the silica vessels due to the pressure of the final traces of water released from the sulfate on the initiation of its decomposition. The second procedure involved roasting the cupric sulfate, with frequent rabbling, in a muffle furnace at 725°C for a period of 48 hr. This produced an excellent product, which was confirmed as copper oxysulfate by X-ray and chemical analyses. The experimental technique used was that of measuring the total pressure exerted by the sulfur trioxide, sulfur dioxide, and oxygen produced by the following reactions: 2 CuS04 = cuo • CuSO4 + SO3 [1] cuo . CuSO4 = 2 cuo + SO3 [2] SO3= SO2 + 1/2 O2 [3] The apparatus used in the experiments has been described previously.1-3 Its main feature of a U-tube mercury manometer in which the mercury is protected from corrosion by enclosure in a flexible Pyrex bellows. Before beginning a run, the interior of the apparatus, including the bellows-manometer and all connecting tubing, was thoroughly washed with hydrochloric acid and distilled water to remove any

Jan 1, 1965

By Peter Beardmore, Michael B. Bever

The effects of the temperature of deformation and the degvee of deformation on the annealing spectrum of a Au-Ag alloy have been determined by vesistance measurements. Specimens were deformed in torsion at 4°, 78K and room temperature up to strains nd/l of about 1.0 and were isochronally annealed. Discrete annealing stages similar to those found for pure metals were observed. Stage A occurred below room temperature; the decrease in reszstance associated with this stage increased as the temperature of deformation was lowered or the strain was increased. Stage B manifested itself as an increase in resistance; this is attributed to the restoration of short-range order promoted by vacancy or vacancy aggregate migration. At temperatures above 48S0K, recrystallization or Stage C occurred. Stages A, B, and C in the annealzng curves of this alloy may be considered to correspond to Stages II, Ill, and V, respectively, in the terminology used to describe the annealing spectrum of pure metals. ThE annealing behavior after deformation below room temperature has been thoroughly investigated on pure metals, in particular gold and copper. The occurrence of several discrete stages in the annealing spectrum of these metals has been established, but the interpretation of some of these stages in terms of specific mechanisms is still controversial.' The annealing of alloys deformed below room temperature has been the subject of only a few investigations. In the investigation reported here, a Au-Ag alloy was annealed after deformation at and below room temperature. This continues a research program on the deformation and annealing behavior of Au-Ag alloys.2-8s EXPERIMENTAL PROCEDURE An alloy rod of composition 82.6 wt pct Au-17.4 pct Ag was reduced to wire, 0.0428 in. diam, by swaging and drawing. After a recrystallization treatment, the grain size was 0.031 mm, as obtained from the average linear intercept.7 The ends of wires about 6 in. long were flattened and sealed into short brass tubes with cold setting cement to form the grips of the torsion specimens. The equipment used for deformation has been described elsewhere.6 The specimens were deformed at room temperature, 78", and 4°K to various strains nd/l, where n is the number of turns, d the diameter of the specimen, and 1 its length between grips. The strain rate ?max was 0.1 min-' at the sur- face of the specimen except where noted otherwise. The specimens were annealed isochronally for 30 min at intervals of approximately 30°K from the temperature of deformation to approximately 800°K, except that after deformation at 4°K the lowest annealing temperature was 78°K. A potentiometric method was used to measure the resistance: all measurements were made at 78°K with the exception of some measurements at 4°K mentioned below. Data obtained with a single specimen yielded a complete annealing curve: in several cases duplicate specimens were used to confirm the reproducibility of the curves. Since the surfaces of the specimens were rough after deformation, their diameters could not be measured accurately. The resistance increments after deformation and annealing are therefore reported as percentages of the resistance of the same specimen measured after completion of the annealing, that is, after full recrystallization. The corresponding resistivity values can be calculated by obtaining the effective diameter of a deformed specimen from the ratio of its resistance after recrystallization to the true resistivity, which was determined with a smooth specimen of known dimensions. This method of calculation was used to obtain data shown in several of the figures. RESULTS AND DISCUSSION The isochronal annealing curves after deformation to various strains at 4", 78K, and room temperature are shown in Figs. 1, 2, and 3, respectively. The resistance increment of the as-deformed specimens as a function of strain is shown in Fig. 4. For the specimens deformed at 4°K. values measured at 78°K are plotted with the exception of those for the as-deformed

Jan 1, 1970

By John F. Blandy

IT is not my intention in this article to consider this subject in the light of the geographer or geologist, but rather in that of the mining engineer, and to endeavor to show the necessity and value to him of studying the minor details of the field or district in which he may be engaged. I t has been said by a distinguished geologist that "the natural boundaries of the geographer are rarely described by right lines. Whenever they occur, however, the geologist may look for something remarkable." And again : " Physiognomy is no idle or doubtful science in connection with geology. The physiognomy of a country indicates almost invariably its geological character." Our country furnishes examples enough of the truth of these remarks, and in no part of it is it so beautifully illustrated as in our own State, which has been so ably described by Prof. Lesley in his admirable little work on the "Topography of Coal." As the great mountain lines become guides to the geologist in determining and mapping out the geography of the formations, so do the minor details of topography become guides to the mining engineer in conducting his explorations, discovering of dislocations, and determining the character of the deposits which are the object of his search. I t is therefore requisite that he should, whilst making his surveys, pay the strictest attention to every variation of the landscape and surface of the ground. Until he has mapped out every feature he may be unable to read the geological changes which may have

By B. Zondek, W. T. Cardwell, J. W. Sheldon

The fundamental equations that are used to describe two-phase fluid flow in porous media are Darcy's law for each phase and an equation of continuity for each component. The special case of one-dimensional, incompressible, two-phase flow has received much attention in the petroleum engineering literature.1-10 The basic paper on the subject is that of Buckley and Leverett.2 Buckley and Leverett showed that one could eliminate the pressure and obtain a single partial differential equation for the saturation. They solved this equation for the case when gravity and capillary forces are negligible. A frequently encountered property of the solution of the basic partial differential equation is that, as time progresses, the saturation becomes a multiple-valued function of the distance coordinate, x. Buckley and Leverett interpreted the formation of multiple values as an indication that the saturation-distance curve had be-come discontinuous. They developed a method of determining the position of the discontinuity from a material balance. We solve the Buckley-Leverett partial differential equation using the method of characteristics and the concept of shocks. Our treatment is analogous to treatments used in the theory of supersonic compressible flow." Although the numerical results obtained are the same as those obtained by previous methods, we believe that this approach is more logical and has broader applicability. It can, for example, be generalized to treat the case when the fluids are compressible. It is not clear how one would go about doing this using the method of Buckley and Leverett. To illustrate the power of the method of characteristics with shocks, we solve a problem in gravity segregation which has not been treated previously in the literature. A special case of the general method developed here was used by Welge, to solve a particular fluid displacement problem. We consider two-phase incompressible flow along the vertical direction x in a porous medium. We assume that there is no flow transverse to .x. We measure positive in the upward direction. The fundamental equations are obtained from Darcy's law and the mass conservation law. Since the two phases are incompressible, mass conservation is equivalent to volume conservation.

By W. A. Gibson, Zay Jeffries

It has been known for a number of years that certain aluminum alloys could be hardened by quenching from a temperature of about 500' C. Immediately after quenching the total increase in hardness is not marked, but the hardness increases gradually so that after about 4 days, it has reached a maximum. The actual increase in hardness probably continues for weeks or even months, but in order to detect the differences after 4 days, it is necessary to make tests at rather long intervals. So far as is known to the authors, Alfred Wilm was the first to discover these properties in aluminum alloys.' The aluminum-copper alloys are amenable to this treatment and the addition of magnesium makes the heat-treatment effect more pronounced. Until recently heat treatment of aluminum alloys has been confined to the worked alloys in the form of sheet or extruded products. The alloy that has been most used in this connection is known commercially as duralumin and has about the following composition: copper not exceeding, 6 per cent.; magnesium not exceeding, 2 per cent.; manganese not exceeding, 1 per cent.; commercial aluminum,2 balance. A typically good alloy in this range consists of: copper, 4 per cent.; magnesium, 0.5 per cent.; manganese, 1 per cent.; commercial aluminum, balance. This alloy can be rolled into sheets or extruded; and in this condition it can be heated in the ordinary furnace atmosphere to a temperature near 500° C. and quenched in water. After about 4 days it will have the following physical properties: tensile strength 55,000 to 60,000 1b. per sq. in. (3866 to 4218 kg. per sq. cm.); elongation in 2 in., 15 to 20 per cent. No harmful effects of the furnace gases or even the air, if the heating is effected in an electric furnace in an air atmospherc.

Jan 1, 1921

By M. E. Nicholson

The solid solubility of boron in iron has been determined by saturating iron with respect to FeyB at several temperatures from 870° to 1135 C. In alpha iron the maximum solubility was found to be 0.002 pct B and in gamma iron the solubility varied from 0.001 pct at 915°C to 0.020 pct B at 1165OC. The eutectic and peritectoid temperatures were found to be 1165° and 911 °C respectively and the gamma iron solidus was located approximately at 0.020 pct B. RECENT investigations of boron-treated steels', ' indicate that the solubility of boron in austenite is of the order of 0.003 pct at 900°C. This has led to the general belief that the solubility of boron in a and r iron is considerably less than that indicated by Wever and Muller." Therefore the solid solubilities of boron in a and r iron have been re-determined. The eutectic and peritectoid temperatures were also remeasured and the r-iron solidus was studied in some detail.* In 1929 Wever and Miiller investigated the phase equilibria of Fe-B alloys. Fig. 1 shows the solid solubility region of the Fe-B diagram based on their investigation. They found that boron lowered the A, transformation temperature to 1381 °C where saturated 6 solid solution "which must contain about 0.15 pct B" and "r solid solution containing about 0.10 pct B" are in equilibrium with liquid containing 1.9 pct B. At the eutectic temperature of 1174"C, 7 solid solution was found to contain "about 0.15 pct B." A peritectoid relation was found to exist between a and y iron with an invariant temperature at 915 "C, where the boron solubility in 7 iron was "about 0.10 pct B" and the solid solubility in a iron "did not exceed 0.15 pct B." Although most of their

Jan 1, 1955

By Albert A. Mathews

OUTCROPS of gypsum rock near the present site of the city of Gland Rapids, Mich., were known to fur traders early in the nineteenth century. However, the deposits seemed without value and were not worked for some time. So far as cat1 be learned, Michigan gyp- sum was first used by a plasterer who settled in Grand Rapids in 1834 as a member of its fourteenth white family. In building a house for one of the early traders, be used some otnamental stucco mouldings manufactured from the local gypsum deposits for decorations in the gables and around some circular windows. The gypsum was broken out with a hammer, ground in an Indian corn mill, and burlled in a caulclron kettle,. After two attempts, the ornaments were successfully set, and remained on the house until it was destroyed by fire in 1850.

Jan 1, 1936

By David White

While a country is small and its coal fields are not many, it may be possible to classify its coals on some basis that avoids both overlap and inconsistency, and that may be satisfactory to the particular country, such as geographic distribution or geologic age, or regional uses. In the adjoining country, however, the coals may differ more or less; broad areas may have escaped the erasure of transition zones by erosion, and the stages of alteration of the coals may lead to a classification different from and even incompatible with that of the other country. Such classifications, developed primarily along national lines, are essentially opportunistic. Further, many even of the "use" terms that have been in more common employment with a degree of international application have lost their significance and value, due to changes in industrial methods and urban life. When the number of coal fields is large and the classification is designed to cover the coals of many countries, the groups or divisions into which the coals are integrated are found to verge one into another; and, though the main divisions may be so naturally composed and oriented that they are relatively distinct and readily separated as entities or units when taken by themselves, the sequence, through classes, groups, and subdivisions, is so complete that we find transition zones through which boundaries must be arbitrarily drawn with minute technical definition. This situation, which is conspicuously illustrated in the United States, is due to the progressive evolution of all coals, irrespective of geologic age, from peats to successively higher ranks, which, if the progressive alteration goes far enough, ends with graphite. This evolution is now firmly established and its complete acceptance is but a matter of time. A classification of all coals in all coal fields can not escape this fact and must take into account all the stages in the transformation of the fuel from rank to rank through division to division, and through group to group. The plan here outlined aims at a natural classification of coals based on their evolution from peats to graphite. As in other classifications, the differentiation of the various groups and divisions takes account of changes resulting from the progressive losses of moisture and .of oxygen of constitution; the relative conservation of carbon; the progressive increase in fixed carbon (inverse to the loss of volatile matter) in

Jan 1, 1930

By E. H. Crabtree

Research on the iron ranges begins to bear fruit in big plant construction -Big coppers raise capacity, build at new Arizona, Michigan, Nevada, properties - Hydrometallurgy comes to fore with new uranium ore treatment and the Chemico process for nonferrous metals -

Jan 2, 1953

By C. G. Grant, Wm. B. Price

This investigation of low copper-nickel silvers was untiertaken to check the work of Lèon Guillet on special brasses and to determine, more accurately, the effect of the addition of nickel on the mierostructure of the binary alloys of copper arid zinc. It was hoped that the results could be successfully applied to the practical production of low copper-nickel silvers. To explain the results of his investigations on special brasses, Lèon Guillet evolved his conception of "fictitious compositions." He states,' in his general conclusions, that on the introduction of a small amount of a third metal to a copper-zinc alloy, it enters into solid solution with the normal constituents up to saturation, but by so doing it brings the ternary alloy into a state microscopically equivalent to a binary copper-zinc alloy of fictitious composition, and physically more nearly like the latter than the brass containing copper-zinc in the ratio actually present. The physical properties of the ternary alloy, when compared to the same properties of an actual brass of the fictitious composition, are modified by the natural properties of the third element. Beyond the point of saturation, a special constituent appears and the above generalization no longer holds. For example, if a 60:40 brass has 4 per cent. of tin substituted for 4 per cent. of zinc, the actual composition would analyze 60:36:4. Assuming that 1 per cent. of tin plays the same part as 2 per cent. of zinc, the proportions of copper and equivalent zinc may be stated as 60 parts of copper and 44 parts of zinc, which, figured to 100 per cent., gives an analysis of 57.7 per cent. of copper and 42.3 per cent. of zinc, the fictitious composition for a 60:36:4 tin brass. The relation between ternary alloys containing copper and zinc together with a third metal, and the microscopically equivalent binary alloy of copper and zinc, may be expressed mathematically.

Jan 1, 1924

By A. M. Rowe

A considerable quantity of experimental hydrocarbon K-factor data has been correlated as a function of component identity, temperature, pressure and convergence pressure. To utilize these correlations effectively, convergence pressure must be determined accurately, particularly for volatile mixtures near their critical states. This paper presents phase diagrams that illustrate physically the meaning of convergence pressure. A new method, referred to hereafter as the "critical composition method", will be outlined for calculating convergence pressure. An example calculation has been included to illustrate how to use this new technique. INTRODUCTION The principle of hydrocarbon phase composition calculations as applied to such diverse problems as optimizing separator performance or predicting fluid compositions at various stages of reservoir depletion is the same. Usually, temperature, pressure and the numbers of moles of the various components of the fluid contained in a given volume are known. Questions answered by the phase calculation are what fraction of the total mass of fluid exists in each of the equilibrium phases, and what are the mole fractions of the various components in the two phases? To answer these questions the Natural Gasoline Supplymen's Assoc. (NGSMA) has correlated a considerable quantity of K-factor data as a function of temperature, pressure, component identity and convergence pressure.l To use these correlations to obtain the best answers possible, one must be able to calculate the convergence pressure. This is particularly true for over-all fluid compositions in the neighborhood of the critical state. STATEMENT OF THEORY Use of convergence pressure as a correlating parameter is based on a postulate similar to the law of corresponding states used in correlating PVT data of hydrocarbon gases. This postulate, which proposes convergence pressure as a correlating parameter, has been stated as follows: "The equilibrium vaporization constant for one component in a complex system is the same as the equilibrium constant at the same temperature and pressure for the same number or kind of components, providing only that the convergence pressures of the two systems are exactly the same at the same temperature and that the components are of the same homologous series".2 This law, as with all laws of physics, cannot be proven theoretically. It can only be justified by experimental data supporting its premises. Arguments have been made that this law violates Gibb's phase rule. For example, consider a four-component system. By Gibb's phase rule, which is thermodynamically rigorous, f = c — P + 2 =4, for a four-component, two-phase system. Thus, four independent intensive variables must be specified to establish completely all the intensive variables of the equilibrium phases. On the other hand, according to convergence pressure theory, only three variables need be specified for any mixture containing four different components. These variables are temperature, pressure and convergence pressure. Thus, the two laws appear to be in conflict. However, the convergence pressure postulate is more restrictive than Gibb's phase rule. It applies only to mixtures of the same homologous series. Hence, these two concepts are not in disagreement. PHASE DIAGRAMS DESCRIBING CONVERGENCE PRESSURE This paper presents phase diagrams grading from the simple two-component system to the more complex four-component system to illustrate convergence pressure. A less abstract definition of convergence pressure will be stated that is

By C. P. Besse, G. W. Osborne

Drilling operations on the Gulf of Mexico continental shelf are following two general plans. The first plan placed all buildings. equipment, and materials on a large platform while the second copies Lake Maracaibo drilling methods by placing a minimum of equipment on the platform and using a floating drilling tender or drill barge anchored adjacent to the platform in an attempt to take maximum advantage of flotation in an effort to reduce costs. A complete power rig, mud pits, pipe racks, and small auxiliaries have been placed on the platform as shown in Figure 1, to assure proper handling of drilling operations under the most adverse weather. This has the economic advantages of eliminating the fabrication of a large structure, a material reduction of rigging up time on each structure. and elimination of delay time on equipment while quarters and equipment placed on the tender are being rigged up. These factors have certainly proved their economic value in drill barge operations in the Louisiana and Texas coastal area. Naturally the heart of such an operation is the anchorage. This anchorage, to permit taking advantage of maximum economies. must hold the ship in a relatively fixed position under the following weather conditions: (1) Winter northwesters (2) Southeasterly gales (3) Severe rain squalls In hurricane weather all operations must be suspended regardless of method of operation and the floating tender will, if possible, be moved to a protected location. However, in case of an emergency the floating tender should be prepared to swing with the wind and seas on a single anchor as there is considerable doubt that either ship or anchorage could withstand the severe strains imposed by fixed anchorage in hurricane weather. Northwesters are reported to have developed wind gust velocities as high as sixty miles per hour and steady winds of approximately forty-five miles per hour. Fortunately these winds do not travel a great distance over water before arriving at our location, and, while they can possibly develop seas approximately eight feet high, the waves are short, and if taken on the bow or stern of a ship 250 feet or more in length they should not present a difficult problem. On the other hand southeast gales having a long fetch and maximum steady wind velocities of approximately thirty miles per hour can possibly develop long swells approximately twelve feet in height. These should develop the most severe anchorage problem. To combat these waves any workable anchorage plan should permit maneuvering the ship in such a manner as to head the bow or the stern into the seas and still maintain contact with the structure. Rain squalls develop wind gust velocities as great as sixty miles per hour. However, they are local and the seas have not been a source of great trouble. To permit continuous operation the anchorage must be able to withstand these winds broadside to the ship as the wind direction often changes radically in a very sliort time. All of these weather conditions are dangerous to small craft, deck cargoes,

Jan 1, 1949

By C. P. Besse, G. W. Osborne

Drilling operations on the Gulf of Mexico continental shelf are following two general plans. The first plan placed all buildings. equipment, and materials on a large platform while the second copies Lake Maracaibo drilling methods by placing a minimum of equipment on the platform and using a floating drilling tender or drill barge anchored adjacent to the platform in an attempt to take maximum advantage of flotation in an effort to reduce costs. A complete power rig, mud pits, pipe racks, and small auxiliaries have been placed on the platform as shown in Figure 1, to assure proper handling of drilling operations under the most adverse weather. This has the economic advantages of eliminating the fabrication of a large structure, a material reduction of rigging up time on each structure. and elimination of delay time on equipment while quarters and equipment placed on the tender are being rigged up. These factors have certainly proved their economic value in drill barge operations in the Louisiana and Texas coastal area. Naturally the heart of such an operation is the anchorage. This anchorage, to permit taking advantage of maximum economies. must hold the ship in a relatively fixed position under the following weather conditions: (1) Winter northwesters (2) Southeasterly gales (3) Severe rain squalls In hurricane weather all operations must be suspended regardless of method of operation and the floating tender will, if possible, be moved to a protected location. However, in case of an emergency the floating tender should be prepared to swing with the wind and seas on a single anchor as there is considerable doubt that either ship or anchorage could withstand the severe strains imposed by fixed anchorage in hurricane weather. Northwesters are reported to have developed wind gust velocities as high as sixty miles per hour and steady winds of approximately forty-five miles per hour. Fortunately these winds do not travel a great distance over water before arriving at our location, and, while they can possibly develop seas approximately eight feet high, the waves are short, and if taken on the bow or stern of a ship 250 feet or more in length they should not present a difficult problem. On the other hand southeast gales having a long fetch and maximum steady wind velocities of approximately thirty miles per hour can possibly develop long swells approximately twelve feet in height. These should develop the most severe anchorage problem. To combat these waves any workable anchorage plan should permit maneuvering the ship in such a manner as to head the bow or the stern into the seas and still maintain contact with the structure. Rain squalls develop wind gust velocities as great as sixty miles per hour. However, they are local and the seas have not been a source of great trouble. To permit continuous operation the anchorage must be able to withstand these winds broadside to the ship as the wind direction often changes radically in a very sliort time. All of these weather conditions are dangerous to small craft, deck cargoes,

Jan 1, 1949

By J. A. Holmes

SHUTTING-IN the Rangely gas well was an interesting problem because of the high rock pressure and the volume of gas developed, as well as the difficulties encountered. After nearly a week's open flow, the rock pressure was 1275 lb., which corresponds with a 2950 ft. hydrostatic head. The volume of gas was between 45,000,000 and 50,000,000 cu. ft. per day. The Rangeley oil field, which now has a daily production of 100 bbl. of shale oil from shallow depth, lies approximately 100 miles north and 30 miles west of Grand Junction, Colo.; not far from the Utah line. The, well we are considering was drilled on the apex of a large clearly defined. Structure1 in the SE.1/4 sec. 30, T. 2 S., R. 102 W., and entered the gas sand at 2954 ft. on March 2, 1925. The condition of the well at the time the gas was encountered was as follows: 20 ft. of 20-in. conductor cemented with ten sacks at 40 ft. The 15 1/2-in. casing was pulled when the 12 1/2-in. was cemented. 1166 ft. of 12 1/2-in. casing, cemented with fifteen sacks. 2531 ft. of 10-in, casing, cemented with ten sacks; neither the 12 1/2-in. nor the 10-in, casing shut off water but they were cemented for protection. 2938 ft. of 8 1/4-in. 36-lb. casing, hanging on a spider in the collar with a forged-steel, high-pressure bradenhead between it and the 10-in. casing. An 8 1/4-in. drilling, or master, gate and a control head were in place on the 8 1/4-in. casing, and all was in readiness for the bringing in of the well.

Jan 1, 1926

By J. C. McCarthy, J. B. Stone

AT Fresnillo a series of veins that has yielded very large quantities of silver and other metals has been developed over a length of 6500 ft. and to a depth of over 3000 ft. In the course of this work striking changes in the mineralogy and metal content of the principal veins have been disclosed and are well illustrated by assay data and ore reserve calculations. This paper describes those changes and suggests their bearing on theories of ore deposition. LOCATION The Fresnillo mines and the adjacent city of Fresnillo are in the central part of the state of Zacatecas, 35 miles northwest of the capitol city of Zacatecas, once a great silver-mining center whose total production is said to place it fourth in the world. Another famous old silver district, Sombrerete, lies northwest of Fresnillo. Fresnillo is connected by a 5-mile branch with Fresnillo station on the Mexican National Railways line from Juarez to Mexico City. Lying near the southwestern edge of the central plateau of Mexico, Fresnillo is surrounded by a semi-arid rolling plain from which rise widely scattered low hills. One of these is Proano hill, an inconspicuous elevation rising barely 300 ft. above the plain, but in and around Proa[n]o hill are the Fresnillo mines, and it is marked now by a great gash cut by gloryhole mining. HISTORY According to an account written in 1834 by Francisco García, then Governor of the state of Zacatecas, Fresnillo was discovered in 1554, and a presidio was established there in 1568 to protect travelers on the road between Zacatecas and Sombrerete. Little is known of the earliest mining at Fresnillo. which seemingly began soon after its discovery, but by piecing together various accounts, it appears that mines there were working in 1717 and were notable active in 1751 under an administrator named Murguía, who left detailed notes describing them. In 1757, however, the mines became inactive because of difficulties with creditors and no doubt also because of increasing water troubles, and they remained abandoned until 1830. In 1830 the mines at Fresnillo became the property of the State of Zacatecas because the interest of Governor García had been aroused by the long disregarded notes of Murguía. Under Garcia's energetic leadership the mines were reopened, and silver production began in 1832 in spite of serious difficulties, including abnormal rains and an epidemic of cholera. In 1833 English capital was sought to allow installation of steam-driven Cornish pumps at the two principal shafts and to build the great hacienda de benefacio (the present Proano hacienda). The company formed in 1835 (Cia. Zacatecano-Mexicana) operated successfully until 1872, when its career was brought to an end by the political and economic disturbances

Jan 1, 1942

J. S. UNGER,*Pittsburgh, Pit., (written discussion?).-From the subject of the paper it is natural to expect that the data presented must be results secured from an open-hearth furnace working under normal conditions, but such is not the case, as the conclusions are based on the results of laboratory tests, which do not approach service conditions. The early basic hearths were made of burnt lime, then followed burnt dolomite, bricks made of calcined dolomite and a 'binder, usually tar, and finally magnesite bricks covered with a layer of sintered magnesite. When this material became scarce, special dolomitic refractories were used. In the summary, it is claimed that magnesite low in lime, or of greatest purity, ranks first in the resistance to slaking and to corrosive slags. It is well known that neither pure lime nor magnesia has much value as a refractory. By the addition f fluxes, such as silica and iron oxide, lime is rendered inert to slaking in the same way as are the special dolomitic refractories. An example on a large scale is the ordinary basic open-hearth cinder, produced every clay, which does not slake. Pure magnesia, regardless of the lime content, is not any better fitted for a refractory than pure lime. The pure natural varieties, such as Grecian or Washington magnesites, must be burnt with sufficient silica and oxide of iron to produce a satisfactory material. Grain magnesite, either artificial or natural, is, not used in burning in a hearth in the state in which it is received. To make a satisfactory hearth, it must be made more impure by adding about 20 per cent. of basic open-hearth cinder, otherwise it will-not remain in place.

Jan 5, 1919

The Mining Journal Annual Review. The Mining Journal, London. $1.00, 200 pp., 1952.-Contains 70 specially contributed articles reporting on events in the metalliferous mining industry throughout the world during 1951. The articles are written from the standpoints of: Economics, world mining fields, progress reports on Empire mining companies, and British mining taxation. The review has appeared for a period of 20 years. Technical developments in mining, ore treatment, refining, and metallurgy are covered. Dun & Bradstreet Reference Book. Dun & Bradstreet Inc. 4000 pp., 1952. -Changes, brought about by the expanding economy, have been made for the three million listings for the United States and Canada. Planning for the changes started more than 10 years ago. New listings have been included for the metals and mining industries on all levels. The rapid development and specialization of industry have made the old symbols used in previous editions outmoded and a new system is substituted. Atlas of World Mineral Resources, . Edited by William Van Royen and Dr. Oliver Bowles. Prentice-Hall Inc. $10.75, 180 pp., 1952.-Scheduled for publication this fall, the book contains information that has never been published in map form before, as well as much that has not been presented in map form for many years. Facts on 29 minerals most important in world trade are dealt with, along with interpretation of all data available on each mineral, discussion of the world's mineral economy from viewpoint of specific minerals related to mineral exploration, geographical distribution of world's consumption, and appraisal of the adequacy of world's mineral resources.

Jan 1, 1952

By Nicholas J. Grant, Bill C. Giessen

The phase diagram Ta-Ni has been treated repeatedly; investigations up to 1958 are summed up in Ref. 1. Since then, an equilibrium diagram has been presented by Kornilov and Pylaeva.2 They found the following intermediate phases: Ta2N; (CuA12 type),3 "TaNi" (p phase, Mo8Co7 type), TaNiz, and TaNi3 (Ticus type).5 Of these, the crystal structure of TaNin remained unknown, and no further literature reference was found. According to Kornilov and pylaeva,&apos; TaNil melts peri-tectically at 1420°C. A 5-g alloy of Ta + 66.7 at. pct Ni was prepared by inert-gas arc melting using 99.95 pct Ta rod (NRC-MG) and 99.9 pct Ni shot (Fisher). The weight loss after three melts was <2 mg; a microscopically homogeneous ingot resulted. As shown in Ref. 6, no oxygen or impurity pickup needed to be considered under these conditions. Specimens were annealed for 15 hr at 1350°C, 15 hr at 1205oC, and 15 hr at 875°C with subsequent powdering and stress relief for 10 min at 1350°C, 15 min at 1205oC, and 1 hr at 875oC, respectively. Micrographs and X-ray analysis (114.6 mm Norelco camera, filtered CuK, radiation) showed homogeneous one-phase alloys in the as-cast state and at all three temperatures, all having the same powder pattern except for broad lines in the as-cast state. From this it is concluded that either TaNi, melts congruently or its melting behavior is a transition between the eutectic and peritectic cases. Since it was found that very slight surface contamination on stress relieving can considerably alter the structure of similar phases (e.g.,TaPt3),7 patterns before and after stress relief were also compared; they were identical except for line broadening in the non-stressrelieved condition, and two faint impurity lines in the stress-relieved samples. The powder pattern is presented in Table I. All lines were accounted for by indexing with a tetragonal lattice, 0Yh- I4/mmm , with a, = 3.154 ± 0.001A, co = 7.905 * 0.002i and c/a = 2.506. The atomic positions are: 1000; 1/2, 1/2, 1/2] + 2Ta(a): 000; + 4Ni(e): *(002); z = 0.333 * 0.002 This proves TaNi2 to be a representative of the MoSiz (Cllb) type. The variable parameter was determined by grouping the visually estimated intensi- ties according to their 2 indices, plotting their F values, and varying z for best fit, which was obtained at z = 0.333= 1/3. Since absorption was not considered, only the relative intensities with similar 28 can be expected to agree. The interatomic distances are presented in Table 11; the standard error is *o.o2A, resulting chiefly from the uncertainty in z. These distances indicate a coordination number 10 for both kinds of atoms and show that the pseudohexagonal layers along (110) are rather un-distorted. The mean atomic volume of 13.1A3 is close to the Vegard&apos;s law value of 13.3A3, showing

Jan 1, 1964

By J. H. Allen

The air lift method of pumping water is discussed. A review of several large diameter hole drilling projects that used reverse- circulation air-lift techniques is presented. Proposals are made for reverse circulation flow rates for slow rates of bit penetration (5 fph) as well as reverse-circulation flow rates for faster rates of bit penetration (10 fph). The Ingersoll-Rand air lift equations are modified for rotary drilling operations. By establishing minimum reverse circulation flow rates and utilizing the modified air lift equations, the establishment of minimum circulation equipment sizes and a more definitive requirement for improved bit body design should result.

Jan 1, 1978