Search Documents

By C. Cronquist

Since April, 1962, Shell Oil Co. has operated a peripheral line-drive waterflood of the 10.750-ft lower Tuscaloosa (Cretaceous) Denkman sand in the Little Creek field. Located in southwestern Mississippi in the lower Tuscaloosa trend, the field was discovered by Shell in Jan., 1958. Among the largest in the trend, the accumulation is controlled stratigraphically and occurs in an extensive series of alluvial-point bar deposits across a nose that dips gently to the south. The crude oil is 39" API gravity and was highly undersaturated at initial conditions. Early production behavior indicated a depletion drive with slight water influx; primary recovery wm estimated to be 25 million bbl, or 24.5 percent of stock-tank oil originally in place. A.s a result of a favorable mobility ratio and remarkably uniform rock properties, the volumetric sweep eficiency in the waterflood has exceeded 90 percent. Despite the high connate water saturation (56 percent), the displacement efficiency by water injection has been quite efficient, contrary to traditional concepts. Based on observed field flood-out performance, ultimate recovery is calculated to be 46 million bbl. As anticipated, the production rate began declining during 1964 due to a continu ing reducrion in the number of producing wells as flood fronts advanced across the field. Cumulative recovery as of Jan., 1968, was 44.8 million bbl; waterflood operations ~hould be complete by 1970. Introduction Most waterfloods described in reservoir engineering literature involve pattern operations, the most common of which is the five-spot pattern. Only occasiona'lly are linear drives described, even though there probably are increasing numbers being put into operation. Increasing use of linear floods may reflect the accelerating trend towards early application of fluid-injection programs when linear drives are more efficient, as was the case at Little Creek. However. the Little Creek operation is unusual in several respects. It is one of a few successful waterfloods conducted in sands with connate water saturations approaching 60 percent, and it is among the deepest successful water-floods being operated anywhere. Development The Little Creek field was discovered in Jan., 1958, in the lower Tuscaloosa trend in southwestern Mississippi (Fig. 1). The discovery well, Shell-Lemann No. 1, was drilled on a seismic closure about 2 miles southeast of lower Tuscaloosa production at Sweetwater. The well was completed in the Denkman sand at 10,752 ft, and on initial potential it flowed 588 BOPD of 39" API crude on a %+-in. choke; psi was 730 and GOR was 442:l. Development proceeded rapidly on 40-acre spacing, and by the end of 1958 the field was producing approximately 9,100 B/D from 56 wells. Almost all this production came from the northern half of the field. The southern part was discovered in Nov., 1958, at a location almost 2 miles from previously established production. Subsequent drilling established an apparent conneotion about half a mile wide between the twd areas. Development of the field was practically complete by 1961 with the drilling of 155 producers and 35 dry holes. Some early wells were completed open hole but moslt are completed with casing cemented through the productive interval and perforated for production. Geology The lower Tuscaloosa structure in this area is a north-south nose with maximum dips of about 2" on the flanks. There is no discernible faulting at the producing horizon. Productive limits of the field are shown in Fig. 2, which is contoured on a marker just above the main productive zone. A common water level at 10,415 ft subsea was logged at both the northwest and southeast ends of the field. There is a gross oil column of nearly 100 ft (Fig. 2). Since there is less than 40 ft of closure, it is apparent that bhe accumubtion is controlled stratigraphically, being limited by a sand pinch-out across the creslt of the nose. The total produc-

Jan 1, 1969

By Oliver Bowles

THE inorganic non-metallic minerals, that is, the non-metallics exclusive of coal, oil, gas and related minerals, constitute the basic raw materials for a number of essential industries. It is estimated that the value of the raw materials in this group produced in 1919, together with certain of the primary products ordinarily manufactured at the mine, exceeded $800,000,000. They are employed chiefly in the building, agricultural, and chemical industries. It has been estimated, by the Bureau of Mines, that approximately 00,000,000 worth of non-metallic minerals and their products were used in the building trades during 1918; with the great increase in building since that date and the increased cost of materials, the value of non-metals used in such industries during 1920 probably exceeded $500,000,000. The chief of these materials are cement, building stone, crushed stone, sand and gravel, clay products, lime, gypsum, glass materials, slate, talc and soapstone. In many of the producing industries of this great group, the waste is so great that the expense of handling it is an important item in the production cost. The utilization of waste is receiving unusual attention in many of the non-metallic industries at present. The most obvious advantages of such utilization are: (1) Conservation of mineral resources, (2) the removal of waste heaps that in many places obstruct development, (3) manufacture of new and useful products, (4) reduced production costs through elimination of a large part of the item of waste-disposal expense. In many industries there is keen competition between producers of various products used for the same purpose, so that advantage will accrue to the manufacturer who is able to reduce his production costs.

Jan 1, 1921

A price list of publications of the Geological Survey, complete to May, 1931, and with separate monthly notices of publications to (late, will be sent upon application to The Director, United States Geological Survey, Washington, D. C. A leaflet is issued each month listing new publications; it will be sent upon application to the Director, as well as Circulars containing information about topographic maps. Book publications of the Survey include (1) Annual Reports, (2) Monographs, (3) Professional Papers, (4) Bulletins, (5) Water Supply Papers, (6) chapters and volumes of Mineral Resources of the United States, (7) Folios of the Geologic Atlas of the United States and the World Atlas of Commercial Geology, (8) Topographic Folios and Topographic Maps that bear descriptive texts. Monographs, Folios of the Geologic Atlas of the United States and the World Atlas of Commercial Geology, and Topographic Folios and Topographic Maps, are not distributed free. A publication of one of the other classes can be distributed free only until the end of the fiscal year following that in which it was issued. No person can obtain more than one free copy of the same publication, and general requests for free publications, such as all of any series or all on any subject, can not be granted. In ordering publications one is requested to give both the series designation, as Bulletin 738 or Professional Paper 122, and the title. Give full address, plainly written, including county. Prepayment is required and may he made by postal, or express money order payable to the official charged with the sale of the publications. requested, as indicated in the discussion of each classification following; or it may be made in cash-exact amount -at sender's risk. Postage stamps are not accepted in payment for publications.

Jan 1, 1933

By L. D. Rickets

The principles on which an art is founded are usually few and necessarily basic in nature, but he who wishes to achieve the power to select his aides and give success to important undertakings that may be entrusted to him in the future must ordinarily undergo years of drudgery in order to gain the experience that will enable him to distinguish such fundamentals through the haze of reenforcing detail that clothes and tends to disguise them. This especially applies to those who would dream dreams that may come partly true. Professor Henry B. Cornwall of Princeton was a graduate of Freiberg with mining experience in Mexico. He was my friend and mentor during my college life. In 1883 I finished my postgraduate course and had two offers of work to consider. His advice is very clear in my mind today. It was essentially as follows: I know something of the mines of Mexico and have crossed through the mountains of the West. The West possesses a vast area of mountain and valley. California has long had its gold mines, the Comstock and Gilpin County followed and now comes the discovery of Leadville. I believe the West, will become a great mining country. You can choose now to teach here or go to the mountains. Were I in your place I would go West and identify myself with mining.

Jan 1, 1932

By S. P. Rothwell

ABOUT thirty miles north of, the city of Belleville (which is situated on a branch of Lake Ontario), and in the township of Marmora, Ontario,: there is found a. belt of gold-bearing quartz veins, which present geological, mineralogical, and economic features of great interest to the profession. The district in which these veins are found is characterized as a rolling country, with low rounded bills of syenitic granite, overlain on the flanks of the hills by Silurian limestones, which lie in nearly horizontal beds, and in some places are so fine in texture as to afford lithographic stone of a fair quality. The gold-bearing veins run north and south through this belt of syenitic granite, and are quartz-filled true fissures, with micaccous or talcoid slates forming the walls of and horses in the veins. This

Jan 1, 1881

W. P. PUTNAM,. Detroit, Mich.-There is one company that is heating these tubes in an upright position by passing electrical energy directly through the tube itself. The lower connection is attached to an indicator, which shows the point at which the steel passes through the critical range At that point the clamps are released and the tube is dropped into a well of oil. This method simplifies the heat treatment of tubes in long lengths. H. J. FRENCH.-I am not entirely familiar with. the method outlined, but it appears to have one serious disadvantage; that is, the length of tubing that is directly connected with the electrical contacts is wasted and must be cut off due to either heavy oxidation or burning. That is a serious difficulty, if true in all cases, and cannot be overcome, inas-much as it is very difficult to draw long tubes of thin wall. Having once obtained a lot of tubes, to cut, say 14 ft. in length, there is often little excess metal available to discard. Am I correct concerning the burning or heavy oxidation of the metal where it comes in contact with the tube.

Jan 12, 1919

By David B. Reger

Widespread wildcatting for new supplies of natural gas and the beginning of importation from the southwest characterized the petroleum industry of West Virginia during 1944. Within the state, drilling for oil did not increase but. more gas wells were completed than in any previous year since 1937. Out of 40 wildcats drilled there were 25 gas discoveries and 15 dry holes. No commercial oil was found in the 40 wells. The proved limits of several oil pools were slightly extended by marginal drilling, resulting in 1300 acres of new oil territory, although no distinctly new pools were found. At least four new gas pools were assuredly discovered and various successful wildcats indicate future pools or wide extensions. The new proved gas territory, in definite new pools and definite extensions, is about 34,000 acres. A considerable net decline of proved oil has occarred and probably a slight decline of proved gas reserves. The account of operations, as gathered from trade journals and other reporting services, shows that 918 new wells were drilled, resulting in 71 oil wells with 613 bbl. of daily new production; 577 gas wells with 305,372,000 cu. ft. of daily open flow, and 142 dry holes. Also, 107 old wells were drilled to deeper sands, with 22 bbl. and 12,327,000 cu. ft. of added production. On the new wells the oil average was 8.6 bbl. per well per day, and the gas average was 529,241 CU. ft. per well per day. On new wells the ratio of dry holes to completions was 15.47 per cent. On deeper drilling the ratio of failures was 19.63 per cent. Production of oil for the year was estimated by the Oil Weekly as 3,069,000 bbl., as compared with 3,349,000 bbl. in 1943. Production of natural gas for the year is estimated by the author as 200,000, 000,000 cu. ft., as compared with the U. S. Bureau of Mines final figures of 223,789,000,000 cu. ft.t in 1943.

Jan 1, 1945

By Oswald J. Heinrich

AT the Baltimore meeting of the Institute in February, 1879, Mr. Eckley B. Coxe, then president of the Institute, called attention in his address to the subject of Secondary Technical Education, and

Jan 1, 1881

By Y. A. Rocher, J. E. Dorn, L. A. Shepard

Creep activation energies for single aluminum crystals favorably oriented for shear by (010) [101] glide were detemined over the temperature range from 78" to 900°K. Observations of slip bands on the specimen surface were made in conjunction with the investigation. From 78" to 780°K, the activation energies obtained in this imestigation agreed closely with those previously found for creep by (111) [101] slip. Between 78" and 140°K, the activation energy was identified with the Peierls process, while between 260°and 780°K the activation energy was close to that for cross-slip. The coarse wavy slip bands nominally parallel to the (010) plane observed above 260°K were attributed to fine cross-slip. From 800" to 900°K, unusually high apparent activation energies ranging from 28,000 to 54,000 cal per mole were obtained. These apparent activation energies were attributed to re crystallization. AS illustrated in Fig. 1, a recent investigation1 has shown that creep of aluminum single crystals by the (111) [i01] mechanism is controlled by three unique processes, each of which is characterized by a single activation energy which is independent of the applied stress and the creep strain. A comparison of the observed activation energies with theoretically calculated values permits a fairly clear identification of the three operative creep processes. Below 450°K, where the activation energy for creep is 3,400 cal per mole, the deformation is controlled by the Peierls process, the activation energy for creep agreeing well with that calculated by seeger2 for the energy required to nucleate the motion of a dislocation loop against the atomic forces of the lattice. Between 590° and 750°K, the observed activation energy for creep of about 28,000 cal per mole agrees well with the energy necessary to induce cross-slip. Seeger and schoeck3 estimate that the activation energy is about 24,000 cal per mole whereas Friedel4 recently calculated this activation energy to be 28,000 cal per mole. Above 800°K the activation energy of 35,500 cal per mole that was observed for creep agrees well with that estimated for self-diffusion in aluminum.= In this range the operative rate-controlling slip process has been clearly identified as that arising from the climb of edge dislocations. The objective of this investigation is to ascertain whether a single crystal of aluminum favorably oriented for simple shear in the [loll direction on the (010) plane might exhibit uniquely different activation energies for creep from those obtained previously for (111) [101] slip. Whereas the exis- tence of such unique activation energies would constitute incontrover table evidence for new mechanisms of slip, the absence of any new activation energies might suggest that slip of aluminum is confined to the (111) [loll mechanism. Several factors prompted the selection of the (010) [101] orientation for study. First, there are more reported observations of (010) [loll slip than of any other nonoctahe-dral mechanism.8-10Secondly, Chalmers and Martius1l have concluded from considerations of the energies of dislocations that (010) slip is the second most favored mechanism in face-centered-cubic metals. Finally, favorable orientations for simple shear by the (010) [loll mechanism provide the least favored orientation for slip by the (111) [101] mechanism. EXPE-RIMENTAL PRO-CEDURE The high-purity aluminum stock, specimen preparation, shear fixture, extensometry, and experimental technique used in this investigation were the same as those previously reported.' Single-crystal spheres grown from the melt of 99.995 pct pure Al* were _ *The high-purity aluminum used in this investigation was graciously given by the Aluminum Company of America. oriented, carefully machined into dumbbell-shaped shear specimens, annealed, and chemically polished. The finished specimen had a central reduced section 0.190 in. wide and 0.590 in. in diam and 1/4-in. grip sections at both sides, 0.690 in. in diameter. The specimen was oriented in the stainless steel grips of the shear fixture with the (010) plane perpendicular to the dumbbell axis and the [loll direction parallel to the stress axis within 2 deg. Creep activation energies were calculated in the previously described manner1 from determinations of the instantaneous change in shear strain rate produced by an abrupt 15 to 20 deg increase or decrease in test temperature. If is the instantaneous strain rate at strain y and temperature T1, and ?2 the instantaneous rate at y and T2,

Jan 1, 1960

Reserves of Lake Superior Manganiferous Iron Ores Appendix-to paper by CARL ZAPFFE, presented at the Cleveland Meeting and issued, as Pamphlet No. 1664-C, with MINING AND METALLURGY, May, 1927. The author has made several test calculations on the basis of manganese units that are and may be involved. These are summarized here, as follows: On the basis of ore produced since 1902, the average annual requirement of manganese units would be 91,000 tons; on the basis of the production of the past 4 or 5 years, the requirement would be 145,000 tons; on the basis of the year 1925 only, the requirement would be 155,000 tons. Applying the percentage of increase for the next 20 years, as determined by the plat shown as Fig. 3, the total requirement for 20 years would be 3,254,000 to 3,572,000 tons, if one used either 145,000 tons or 155,000 tons as a starting point. We have the following interesting facts: (1) The Michigan ores contain only about one-half the manganese that the Cuyuna ore does; (2) the Cuyuna district now produces one-half the ore required; (3) the known tonnage of Cuyuna reserves is greater than the speculative reserve offered for Michigan; (4) at the present rate of production considered by tons, Michigan ores ought to be exhausted in 20 years or less while Cuyuna ores would last up to 44 years. We should now reduce the estimated reserves to a basis of manganese, units. Using the tonnages listed in Combinations 2, 3, 4 and 5, the reserves total 3,118,225 tons, 3,781,995 tons, 5,041,995 tons and 5,560,342 tons, respectively. Therefore, needing at the most 3,572,000 tons, as shown above, either Combination 3, 4 or 5 will not only suffice but will leave an excess-enough for 1 or 2 years for Combination 3, 9 or 10 years for Combination 4, and 12' to 13 years for Combination 5. This means that for Combination 5, without using tonnages obtained from beneficiating or from mixing poor ores, the reserves are ample for about 33 years.

Jan 5, 1927

By G. Wranglen

On account of the possibility of isolating carbides in steel it is generally assumed that the electrode potential of iron carbide is more noble than that of ferrite.1,2,3,4,5 Differences from 0.032 V1 to 0.4 V4 have been recorded. However, it is important to realize that the more noble behavior of cementite in relation to ferrite is not an issue of thermodynamics but of reaction kinetics. Theoretically, cementite is less noble than ferrite, which is a direct consequence of its thermo-dynamic instability. With the value ?F°298 = +4700 cal per mol for the free energy of formation of cementite6 it is easily calculated that the electrode

Jan 1, 1950

By A. N. Crownover, H. T. Kennedy, E. P. Miesch, C. H. Bowman

The paper presents correlations of (l) molar volume of gaseous hydrocarbon mixtures with pressure, temperature, composition and properties of the C,-plus fraction; (2) shrinkage of oils during flash and differential liberation of gas, including the calculation of formation volume factor under various conditions; and (3) bubble-point pressure with temperature, composition and characteristics of C, plus. The data on which the correlations are based comprise 1,615 measurements on 900 hydrocarbon systems, including numerous systems containing nitrogen, hydrogen sul-fide and carbon dioxide. In each correlation, the number of data points covered and the accuracy is substantially greater than in previously available work. Thus, the equation yielding molar volumes of gases has an average deviation of 2.04 per cent, applied to mixtures having temperatures up to 313F and pressures up to 9,800 psis, compared to 2.37 per cent for the Benedict-Webb-Rubin equation applied to the same data, and 4.53 per cent for the method based on the law of corresponding states. he equations resented are all explicit in the dependent variable, and require no iteration on the digital cow puter. INTRODUCTION The ease and accuracy of determining the composition of hydrocarbon mixtures, compared to the difficulty of measuring their properties under reservoir conditions, makes it desirable to utilize composition as the key to physical behavior to the greatest possible extent. As a result, there are available correlations between composition, or easily measured characteristics dependent on composition, and practically every important engineering property of reservoir fluids. The task confronting us is one of finding more exact relationships between important variables rather than extending correlations to new properties. This paper describes new correlations of molar volumes of gases, formation volume factors, and bubble-point pressures with composition, temperature and where possible, pressure. Each correlation is obtained by employing a sufficiently large amount of data so the calculated properties are probably as least as accurate as the measurement on which they are based. MOLAR VOLUME OF GASES Although many equations of state have been proposed for pure gases, only a few methods are applicable to hydrocarbons at conditions comparable to those in petroleum reservoirs. Still fewer arc useful in describing the behavior of mixtures, with which the petroleum engineer is largely concerned. The correlation presented here involves procedures similar to those of Alani and Kennedy The van der Waals equation is modified to make a and b functions of temperature instead of being constants for each material.This is a cubic equation, which may have either one or three real roots. The lowest root corresponds to liquid volume, while the highest applies to gas. When the procedure was applied to 703 pressure-temperature points of 164 gases of known composition and volume, the average deviation was 12.08 per cent, and the standard deviation 8.15. The above calculations were made using the constants derived for liquids by Alani and Kennedy and the mixture equation developed by them. A closer approximation to measured molar volumes is obtained by employing different sets of constants for different areas on the pressure-temperature chart, and by changing the relationship between a,,, and b,,, for mixtures and the a, and b, for individual hydrocarbons. The various sets are shown in Table 1, and the areas for which they are recommended are plotted in Figs. 1 through 7. In these figures, the area designated by zero is in the critical region for pure materials, and the values obtained for them may be unreliable. For normal mixtures, however, the area may be added to any of the bounding areas without substantial error. The new relationships employed are

Jan 1, 1966

The official Institute reports for the year 1929 were distributed in pamphlet form at the Annual Meeting, February, 1930, and were later included in Section 2 of Mining and Metallurgy, June, 1930, and thus made available to the entire membership. Membership In its report the Admissions Committee set forth the changes in membership during 1929, as follows: Total membership, Jan. 1, 1928, 8582; elected and placed on rolls in 1929, including 59 reinstatements, 509; loss by resignations in 1929, 88; loss by death in 1929, 110; loss by suspension in 1929, 37; membership at end of year not including Student Associates, 8856. Distribution of membership: Honorary Members, 16; Members, 6590; Junior Members, 38; Associates, 1041; Junior Associates, 1033; Rocky Mountain, 138; total membership, Jan. 1, 1930, 8856; Student Associates, 150; total including student associates, 9006. Treasurer's Annual Report, Year of 1929 Statement of Receipts For the year ended December 31, 1929 Dues: Arrears............................................ $ 3,501.75 Current............................................ 97,257.12 New Members...................................... 5,721.50 Advance........................................... 1,970.79 $108,451.16 Initiation Fees.................................................. 7,436.OO Magazine Receipts: Advertising Gross Receipts........................... $40,610.81 Magazine Sales..................................... 3,799.84 44,410.65 Sale of Transactions Current........................... $ 2,985. 15 Sale of Special Editions Current........................ 5,147.82 Sale of Back Transactions and Special Editions........... 4,186.93 Sale of Year Book..................................... 65.50 Sale of Authors' Reprints.............................. 2,585.40 Sale of Pins and Fobs.................................. 14.73 Sale of Technical Publications.......................... 1,451.55 Sale of Bindings...................................... 3,949.13 20,376.21 Net Interest Received: On Bank Balance and Temporary Investments......... $ 2,595.04 On Lie Membership Fund........................... 3,223.43 On James Douglas Library Fund...................... 5,425.61 On General Reserve Fund............................ 2,015.58 13,259.66 Miscellaneous Receipts........................................... 335.80 Total Receipts................................................ $194,269.48

Jan 1, 1930

The official Institute reports for the year 1929 were distributed in pamphlet form at the Annual Meeting, February, 1930, and were later included in Section 2 of Mining and Metallurgy, June, 1930, and thus made available to the entire membership. Membership In its report the Admissions Committee set forth the changes in membership during 1929, as follows: Total membership, Jan. 1, 1928, 8582; elected and placed on rolls in 1929, including 59 reinstatements, 509; loss by resignations in 1929, 88; loss by death in 1929, 110; loss by suspension in 1929, 37; membership at end of year not including Student Associates, 8856. Distribution of membership: Honorary Members, 16; Members, 6590; Junior Members, 38; Associates, 1041; Junior Associates, 1033; Rocky Mountain, 138; total membership, Jan. 1, 1930, 8856; Student Associates, 150; total including student associates, 9006. Treasurer's Annual Report, Year of 1929 Statement of Receipts For the year ended December 31, 1929 Dues: Arrears............................................ $ 3,501.75 Current............................................ 97,257.12 New Members...................................... 5,721.50 Advance........................................... 1,970.79 $108,451.16 Initiation Fees.................................................. 7,436.00 Magazine Receipts: Advertising Gross Receipts........................... $40,610.81 Magazine Sales..................................... 3,799.84 44,410.65 Sale of Transactions Current........................... $ 2,985. 15 Sale of Special Editions Current........................ 5,147.82 Sale of Back Transactions and Special Editions........... 4,186.93 Sale of Year Book..................................... 65.50 Sale of Authors' Reprints.............................. 2,585.40 Sale of Pins and Fobs.................................. 14.73 Sale of Technical Publications.......................... 1,451.55 Sale of Bindings...................................... 3,949.13 20,376.21 Net Interest Received: On Bank Balance and Temporary Investments......... $ 2,595.04 On Lie Membership Fund........................... 3,223.43 On James Douglas Library Fund...................... 5,425.61 On General Reserve Fund............................ 2,015.58 13,259.66 Miscellaneous Receipts........................................... 335.80 Total Receipts................................................ $194,269.48

Jan 1, 1930

The official Institute reports for the year 1929 were distributed in pamphlet form at the Annual Meeting, February, 1930, and were later included in Section 2 of Mining and Metallurgy, June, 1930, and thus made available to the entire membership. Membership In its report the Admissions Committee set forth the changes in membership during 1929, as follows: Total membership, Jan. 1, 1928, 8582; elected and placed on rolls in 1929, including 59 reinstatements, 509; loss by resignations in 1929, 88; loss by death in 1929, 110; loss by suspension in 1929, 37; membership at end of year not including Student Associates, 8856. Distribution of membership: Honorary Members, 16; Members, 6590; Junior Members, 38; Associates, 1041; Junior Associates, 1033; Rocky Mountain, 138; total membership, Jan. 1, 1930, 8856; Student Associates, 150; total including student associates, 9006. Treasurer's Annual Report, Year of 1929 Statement of Receipts For the year ended December 31, 1929 Dues: Arrears............................................ $ 3,501.75 Current............................................ 97,257.12 New Members...................................... 5,721.50 Advance........................................... 1,970.79 $108,451.16 Initiation Fees.................................................. 7,436.00 Magazine Receipts: Advertising Gross Receipts........................... $40,610.81 Magazine Sales..................................... 3,799.84 44,410.65 Sale of Transactions Current........................... $ 2,985. 15 Sale of Special Editions Current........................ 5,147.82 Sale of Back Transactions and Special Editions........... 4,186.93 Sale of Year Book..................................... 65.50 Sale of Authors' Reprints.............................. 2,585.40 Sale of Pins and Fobs.................................. 14.73 Sale of Technical Publications.......................... 1,451.55 Sale of Bindings...................................... 3,949.13 20,376.21 Net Interest Received: On Bank Balance and Temporary Investments......... $ 2,595.04 On Lie Membership Fund........................... 3,223.43 On James Douglas Library Fund...................... 5,425.61 On General Reserve Fund............................ 2,015.58 13,259.66 Miscellaneous Receipts........................................... 335.80 Total Receipts................................................ $194,269.48

Jan 1, 1930

By R. W. Jenkins

RACKLESS equipment is being used by the T Coplay Cement Manufacturing Co. to develop a folded limestone deposit economically and safely with inexperienced men. Cost and quality of development stone results in a saving when it is used instead of outside sources of limestone. This favorable cost has been attained by following a methods development and training program described in this paper. It is expected that further savings in favor of the mined stone will be made when stopes now being prepared are in production. The present equipment will be used for loading from stope draw points. The limestone is blended with quarried cement rock to serve as raw material for Portland cement, first produced in this country by Coplay Cement Manufacturing Co. from a process developed by its president, David 0. Saylor, in 1873. For many years the cement rock alone or with a small amount of added limestone was used for raw materials. Later as specifications were raised and the richer portions of quarries were depleted, limestone from outside sources was required in increasing amounts. In 1925 D. J. Uhle, the general manager, began to prospect company property for limestone. It was known that the argillaceous cement rock was underlain by crystalline high calcium limestone. After an extensive drilling program it was found that there were large reserves of limestone underlying a recumbent syncline exposed in the south wall of the company's No. 3 cement rock quarry. A quarry was started on the vertical limb of this fold in 1927, and by 1930 the full requirement of the plant was met. After 1945 production diminished because of the occurrence of dolomite beds in the south wall. The quarry floor was then 135 ft below the cement rock level and 285 ft below surface. In 1949 Gerald I?.

Jan 1, 1955

By C. E. Cottrell, G. W. Preckshot, N. D. Delisle, D. L. Katz

Most crude oils contain asphaltic substances that may be naturally or artificially precipitated. In the Greeley field, California, this asphaltic bitumen is precipitated during the flow of the oil from the reservoir to the stock tank The mechanism of such precipitation is not well understood. This paper presents the progress that has been made by using the electron microscope as a new tool and by observing the effects of the streaming potential on the formation of bitumen particles. Crude oils at atmospheric pressure viewed in the electron microscope in very thin films under a vacuum showed no asphaltic particles. A technique of preparing slides of thin films by dilution of the oil with benzene and washing in petroleum ether was used at first, and these observations showed that the solvents caused the formation of the particles, varying from 0.01 to 0.2 micron in diameter. The electrical effects of fluids flowing through porous solid were studied, with emphasis on the formation of colloidal particles by the streaming potential. The streaming potential of crude oil flowing through sand was measured and was shown to be responsible for the formation of bitumen particles. These results bring out a new phenomenon, which may occur when crude oil flows through the porous oil reservoir. mechanisms. Asphalt has been the subject of widespread investigation but, owing to the complexity of the substances being considered, progress has been slow. Investigators working primarily with the asphaltic substances have treated the subject from the colloidal standpoint and have developed theories that picture the asphaltic particles as surrounded by adsorbed materia1s.14,15,17,24 The deasphaltization of lubricating oil by the use of solvents treats the subject primarily from the standpoint of liquid-liquid equilibria.'' A complete understanding of asphaltic substances would make possible the following of the material from its initial state in the crude oil through precipitation processes to the final plastic stage, the most common form of which is used in asphaltic pavements. Since these asphaltic particles are very small, it appears 'hat the electron microscope4 might be a useful tool in studying the precipitation processes. Specimens are examined by the electron microscope in a vacuum and as very thin films, requiring special techniques in preparation of samples. A brief description of the electron microscope and its operation will bring out the difficulties and advantages of its use for this problem. The first work was done with crude oils that had been diluted with solvents for the preparation of the film to be examined. Later a technique was developed by which the undiluted oil film could be made thin enough for direct examination. These two techniques show vastly different results Asphaltic particles have been precipitated from crude oils by a variety of

Jan 1, 1943

By G. W. Preckshot, C. E. Cottrell, D. L. Katz, N. D. Delisle

Most crude oils contain asphaltic substances that may be naturally or artificially precipitated. In the Greeley field, California, this asphaltic bitumen is precipitated during the flow of the oil from the reservoir to the stock tank The mechanism of such precipitation is not well understood. This paper presents the progress that has been made by using the electron microscope as a new tool and by observing the effects of the streaming potential on the formation of bitumen particles. Crude oils at atmospheric pressure viewed in the electron microscope in very thin films under a vacuum showed no asphaltic particles. A technique of preparing slides of thin films by dilution of the oil with benzene and washing in petroleum ether was used at first, and these observations showed that the solvents caused the formation of the particles, varying from 0.01 to 0.2 micron in diameter. The electrical effects of fluids flowing through porous solid were studied, with emphasis on the formation of colloidal particles by the streaming potential. The streaming potential of crude oil flowing through sand was measured and was shown to be responsible for the formation of bitumen particles. These results bring out a new phenomenon, which may occur when crude oil flows through the porous oil reservoir. mechanisms. Asphalt has been the subject of widespread investigation but, owing to the complexity of the substances being considered, progress has been slow. Investigators working primarily with the asphaltic substances have treated the subject from the colloidal standpoint and have developed theories that picture the asphaltic particles as surrounded by adsorbed materia1s.14,15,17,24 The deasphaltization of lubricating oil by the use of solvents treats the subject primarily from the standpoint of liquid-liquid equilibria.'' A complete understanding of asphaltic substances would make possible the following of the material from its initial state in the crude oil through precipitation processes to the final plastic stage, the most common form of which is used in asphaltic pavements. Since these asphaltic particles are very small, it appears 'hat the electron microscope4 might be a useful tool in studying the precipitation processes. Specimens are examined by the electron microscope in a vacuum and as very thin films, requiring special techniques in preparation of samples. A brief description of the electron microscope and its operation will bring out the difficulties and advantages of its use for this problem. The first work was done with crude oils that had been diluted with solvents for the preparation of the film to be examined. Later a technique was developed by which the undiluted oil film could be made thin enough for direct examination. These two techniques show vastly different results Asphaltic particles have been precipitated from crude oils by a variety of

Jan 1, 1943

By H. F. Yancey, M. R. Greer

At the annual meeting of this Institute held two years ago a new method1 of estimating the grindability of coal was described, based on experimental work carried on by the Bureau of Mines at its Northwest Experiment Station. Since that time, several organizations concerned with the testing or utilization of coal as pulverized fuel have adopted and used the method in determining the grindability of several hundred samples of coal. In addition, a series of comparative tests of this method and three others has been carried out in five laboratories under the auspices of Committee D-5 of the American Society for Testing Materials. As a result the Committee has recommended that the Bureau of Mines method, designated as the "ball-mill method," and the Hardgrove method2, previously advanced, be accepted as tentative standards3. Since the ball-mill method was originally developed and published, an opportunity has been presented to apply it to a larger number of coals and to study intensively some of the principles upon which the method is based. This paper presents a résumé of these further studies and includes a comparison with the Hardgrove-machine method. Trial runs were also made with another procedure recently proposed—the C.I.T. roll-test method4. Principles of Methods In the ball-mill method, the relative amounts of energy necessary to grind coals to the same fineness are determined by the number of revolutions of the mill required to reduce 80 per cent of the feed (500 grams of 10 to 200-mesh coal) fine enough to pass a 200-mesh screen. This is a

Jan 1, 1936

By H. F. Yancey, M. R. Greer

At the annual meeting of this Institute held two years ago a new method1 of estimating the grindability of coal was described, based on experimental work carried on by the Bureau of Mines at its Northwest Experiment Station. Since that time, several organizations concerned with the testing or utilization of coal as pulverized fuel have adopted and used the method in determining the grindability of several hundred samples of coal. In addition, a series of comparative tests of this method and three others has been carried out in five laboratories under the auspices of Committee D-5 of the American Society for Testing Materials. As a result the Committee has recommended that the Bureau of Mines method, designated as the "ball-mill method," and the Hardgrove method2, previously advanced, be accepted as tentative standards3. Since the ball-mill method was originally developed and published, an opportunity has been presented to apply it to a larger number of coals and to study intensively some of the principles upon which the method is based. This paper presents a résumé of these further studies and includes a comparison with the Hardgrove-machine method. Trial runs were also made with another procedure recently proposed—the C.I.T. roll-test method4. Principles of Methods In the ball-mill method, the relative amounts of energy necessary to grind coals to the same fineness are determined by the number of revolutions of the mill required to reduce 80 per cent of the feed (500 grams of 10 to 200-mesh coal) fine enough to pass a 200-mesh screen. This is a

Jan 1, 1936