Search Documents

By C. P. PERIN, DONALD BELCHER

T HE production of pure iron by electrolyzing solutions of its salts has been the object of scientific curiosity and research for about 80 years; and in the last two decades a realization of the unusual physical and chemical qualities of electrolytic iron has turned the attention of chemists and metallurgists toward a commercial application of this accumulated knowledge. Thus Burgess and Hambuechen in America, . Cowper-Coles in England, and Fischer in Germany- devised methods, more or less successful, for the electrolytic refining of iron, but none of these processes has yet attained large-scale operation. During the war some interesting ,work was done in France and England on building up worn or defective machine parts by electrodeposition of iron. It remained for the Société "Le Fern in France to carry on the process commercially. For six years Les Fonderies et Forges. de Sainte-Maire et Gravigny and the works of Bouchayer & Viallet at Grenoble have manufactured pure-iron boiler tubes in competition with established practice. The French process originated in the researches of Anthelme Boucher in 1910, and was, not put into operation until several years of experimentation had passed.

Jan 1, 1921

By W. L. Fink, L. A. Willey

During the war there was introduced a new higher strength aircraft alloy designated 75S.1,2,3 The properties of this alloy assure extensive applications in both military and commercial aircraft. It is therefore important to understand its limitations as well as advantages. The properties of 75.5 alloy in the heat-treated tempers, like those of many other aluminum alloys, are affected by the rate of quenching. In general, low quenching rates tend to cause low strengths and to adversely affect the resistance to corrosion. Commercial quenching procedures are usually sufficiently rapid to permit the development of maximum properties. However, in the center of heavy sections, such as large rolled and extruded shapes, the quenching rates may not be rapid enough to develop maximum strength or resistance to corrosion. The investigations of 75s alloy described herein reveal the most critical range of temperature and the effects of quenching sheet and extrusions at different rates through that temperature range, on the tensile properties and resistance to corrosion. Procedure Preparation of Specimens Sheet specimens (3 in. by 9 in.) were prepared from a commercial lot of 75s "as rolled" sheet (0.064 in. thick). The composition4 was as follows: Weight Percentage Cu Mn Mg Zn Cr A1 with Normal Impurities 1.64 0.16 2.58 5.66 0.27 Remainder The specimens employed for the determination of the time-temperature relations during quenching of sheet were prepared by the following procedure: the hot junction of a 28-ga. iron-constantan thermoelement (asbestos insulated) was brazed to a thin strip of aluminum which was in turn brazed into the end of a 3/16-in. id by %-in. od by 30 in. long aluminum protection tube. Before brazing, the tube was flattened to 0.064-in. thickness over the junction and adjacent lead wires for a distance of I 1/2 in. The flattened end of the tube was fitted into a slot cut from one edge to the center of the 3-in. by 9-in. by 0.064-in. sheet and brazed into place. The brazed joint was dressed to the thickness of the sheet and the entire specimen buffed to approximately the brightness of "as rolled" material. Because of the brazing operations required, these specimens were prepared using 3S alloy. For the investigation of quenching rates in heavy sections, there were used 75s extrusions which had compositions similar to that of the sheet. The specimens consisted of 14 in. lengths of 3i-in., 2-in., 3-in, and 4-in. diam cylindrical rods and a roughly rectangular extruded section which was approximately 4 in. by 7 1/2 in. Thcrmocouple~ were peened into the bottoms Of .1/8-in. diam wells drilled into one end and parallel to the axis to a depth of

Jan 1, 1949

By Gene D. Clayton, Robert R. Dimock

A time-consuming and expensive preshearing program to minimize the adverse effects of blasting on slope stability at Kennecott Copper Corp.'s Ruth Pit in east-central Nevada has been eliminated in favor of down-the-hole, nonelectric delayed blasting which can produce a smooth wall effect and improve blast fragmentation. The new blasting approach resulted from a Kennecott engineering investigation aimed at improving the stability of the extremely variable rock conditions found throughout the pit by reducing the vibrational energy imparted to the walls with conventional bench blasts.

Jan 4, 1977

By S. H. Williston

IT is not often that bore hole surveys can be checked by actual civil engineering methods. A recent Arizona survey was checked by normal surveying methods and the comparison of the results should be of value to both oil and mining men. During the summer of 1948 the Phelps-Dodge Corporation, at its Copper Queen property near Bisbee, Ariz., drilled a 1245 ft, 8 in. diam, churn drill- hole in a mineralized area and cased part of it, intending to use it to transfer mill tailings for stope fill. The hole, as frequently occurs, was not straight, and, in endeavoring to locate the bottom in- the underground workings, they found no evidence of the hole at the underground coordinates directly below the surface location. The noise of the drilling tools was reasonably clear, but the direction of sound was uncertain. Preliminary tests with available equipment were not successful in locating the bottom of the hole. Be- cause of the mineralized character of the area and the fact there was some casing in the hole, any magnetic method of well surveying would give results ' of doubtful value.

Jan 1, 1950

By Paul R. La Pointe

GEOTECHNICAL OBJECTIVES OF UCG PROGRAM Underground coal gasification (UCG) is one of several in situ extraction technologies for utilizing deep, otherwise unmineable coal. This technology involves the injection of air or oxygen into the target coal seam, ignition of the coal and recovery of product gases. Geotechnical characteristics of the coal and enclosing rock strata strongly influence the success of this Process. The flame front follows the coal cleats (Hill, 1979), and cleating and bedding control the manner in which coal collapses into the cavity, thereby affecting recovery efficiency (Ramirez and others, 1982). Moreover, coal seams typically behave as fracture dominated aquifers in which cleat orientations govern subsequent contaminant dispersal. For these reasons, the Anaconda Minerals Co. undertook a detailed study of fracturing within the Wyodak-Anderson Coal in the eastern Powder River Basin (PRB) near its Rocky Hill UCG test site (Fig. 1). STRESS HISTORY AND FRACTURING IN THE POWDER RIVER BASIN Vertical jointing, or cleating, in coals may arise from shrinkage shortly after deposition under low confining pressures, or later in time, soon after burial but after the coalification process is well advanced (Ting, 1977). There is much evidence to support the formation of cleating after coalification (e.g. Hawkes and Mellor, 1970; McCulloch and others, 1974), which suggests that the stress state existing at that time strongly influences cleat formation. McCulloch and others (1974) argue that the typically better developed face cleat forms parallel to the plane containing [ol] and [o2]. Where the relation between cleats and stess has been studied (McCulloch and others, 1974; Stone and Snoeberger, 1977; Ward, 1977; Kulander and Dean, 1978), the highly systematic face cleat strongly parallels the [o1] direction. Stone and Snoeberger (1977) report face and butt cleat measurements of N70E and N29W for the Felix Coals 220 m stratigraphically above the Wyodak at the Hoe Creek UCG site (Fig. 1). Structural trends also indicate the past state of stress in the PRB. Glaze and Keller (1963) suggest that the NE-SW regional compression during the late Permian formed major N-S fold lines and basement magnetic anomalies. Mapel (1959) describes folds having N60W and N30W rends in the northern PRB, as well as a large normal fault trending northeast. Glass (1976) also describes normal faults trending northeast. Similarly, Olive (1957) mapped normal faults

Jan 1, 1984

By Horace Pops, L. L. Isaacs

SOLID-STATE transformations at low temperatures are frequently studied by optical metallography. Greninger and ooradian' and Hull and Gar-wood2 have examined the martensitic-type transformations in 0-phase Cu-Zn alloys during continuous cooling below room temperature. The lowest range of temperatures in the apparatus described by these investigators is limited to approximately 110°K. Present studies of reversible first-order phase transitions near liquid-helium temperatures have necessitated the design of a new cold-stage cryo-stat for optical metallography. The features of interest of this instrument are as follows: a) temperatures down to 4.Z°K are obtainable; b) the specimen is always under vacuum, thereby avoiding the condensation of moisture; c) specimens can be rapidly cooled or heated at varying rates, thus permitting studies of transformation hysteresis. Fig. 1 shows the details of the cryostat. All major parts are made of type 304 stainless steel. Both helium and nitrogen cans are Heliarc-welded to the helium filling tube, permitting the use of a common shielding can. Hence, the over-all weight and the area of the evacuated surface are mini- mized. The copper sample holder is screwed into the bottom of the helium can. To assure good thermal contact between the sample holder and the refrigerant, an indium ribbon is placed on the threads

Jan 1, 1964

DR. PeRsifor Frazer, Philadelphia, Pa. (communication to the Secretary):* Mr. Campbell's very interesting contribution, after complimentary mention, finally decides against the acceptance of the classification proposed by me in a paper bearing the same title and read at the Wilkes-Barre meeting, May, 1877.2 That paper was written primarily for the Second Geological

Jan 1, 1906

MARSHAL Foch has been made an honorary member of the four national American societies of civil, mining and metallurgical, mechanical, and electrical engineers. The governing bodies of these societies, aggregating 45,000 members, conferred this signal honor in expression of the appreciation of American engineers for the unmatched services of this master of engineering principles. At Engineering Societies Building, in New York City, on Tuesday afternoon, Dec. 13, the presidents of the four societies presented one beautifully engrossed certificate of honorary membership in the four societies. The auditorium was filled so that not even standing room was left, more than a half hour before the cere-monies began, and the main entrance on the street had to be closed. J. Vipond Davies, president of the United Engineering Society, made the opening address. Col. William Barclay-Parsons, 'who was commander of the first engineer regiment to go abroad, addressed Marshal Foch in French. Colonel Parsons said: The art of engineering was defined a long time ago as "the art of directing the great sources of power in nature for the use and convenience of man." No better definition can be found today. Of all the sources of power in nature, the greatest, the most valuable, and at the same time the most difficult to direct, is the energy of man himself. He who can direct human energy and turn it to the service of mankind is a great engineer. You, Marshal, have directed a greater mass of human energy than any other man has ever done. And you have successfully directed this mass for the highest uses of mankind, in that you by its aid have preserved for him one of the most precious of human possessions-liberty-liberty not only for your own illustrious country, but for all the nations of the world. The four national engineering societies, of the United States now desire to make record of their appreciation of this fact and to convey to you an expression of their most profound admiration for the great leader of men by conferring on you honorary member-ship in all the societies, the highest honor in their gift and one hitherto never conferred on a single individual. Four thousand members of these societies were enrolled in the armed service of the United States, the greater part of whom had the glorious distinction to serve the common cause in France under your orders. They heard the voice and they saw the hand of the master as he led them through battle to victory. Now we desire that you will still continue to lead us, but in peace, by permitting us to inscribe your name at the head of our roll of honor, where it will be, as your deeds have been, an example to us to do better work, and where it will remain forever a noble inspiration for all future generations. Marshal, in the name of those members of the societies who served under your orders and particularly .in the name of those who fell on the field of honor in France, I salute you.

Jan 1, 1922

By E. F. Evoy

The uranium deposit of Gunnar Mines Ltd. is on south shore of Crackingstone Peninsula in the Beaverlodge area of northern Saskatchewan. The property spans St. Mary's Channel, a narrow waterway separating the mainland from a group of islands in Lake Athabasca. The mine property, consisting of 12 claims and 7 fractions, was staked in July 1952 by A. O. Zeemel and W. J. Blair. Diamond drilling commenced in the fall of that year and continued until the spring of 1954. In that interval, some 70,000 ft of drilling outlined an orebody plunging from the surface south-ward to a depth of 1000 ft below the shore of St. Mary's Channel. The last 9000 ft of drilling was through lake ice, and when this was interrupted by spring breakup, sufficient ore reserves had been established to warrant the present operation. Surface drilling was therefore terminated.

May 1, 1956

By R. P. Smith

The diffusivity of carbon in iron, cobalt, and alloys of 89.7 and 79.3 wt pct Co has been determined by a decarburization method for the temperature range 850° to 1100°C. The Plots of log D us 1/T for the two Fe-Co alloys are linear through the region of the Curie temperature, showing that, unlike some cases of substitutional diffusion, carbon diffusion in these alloys is not affected by electron spin order. RECENT investigations1-' have shown that for substitutional diffusion in iron the change in diffusivity with temperature does not follow an Arrhenius equation, at temperatures near the Curie temperature. Data on the diffusivity of carbon in a iron5"9 indicate that this anomaly does not exist for interstitial diffusion; however, this has not been definitely established. Since cobalt and Fe-Co alloys, 80 to 100 pct Co, have Curie temperatures in a temperature range convenient for carbon-diffusion measurements they are suitable systems for studying the relation of interstitial diffusion and the Curie temperature. EXPERIMENTAL The carbon diffusivity, D, was determined by a decarburization method. The diffusion cylinders, made from small vacuum melts of electrolytic cobalt and plastiron, were about 0.76 cm diam and 6.3 cm long. A small amount of carbon was added to each melt to keep the oxygen content as low as possible. The cylinders were first treated with a hydrogen-3 pct water vapor mixture at 1100°C to constant weight, then carburized to the desired initial carbon content with a suitable CO-C02 gas mix-

Jan 1, 1964

By Arthur F. Taggart

The quality of aggregate materials is. of major importance in governing durability and permanence of concrete structures. The problem of selecting suitable aggregate materials is two-fold. Geological factors include the type and character of the aggregate source, presence of known or suspected reactive constituents, and presence of thermally incompatible materials. Laboratory investigations include petrographic studies, soundness and reactivity tests, and tests of thermal properties. The importance of each factor in the selection of satisfactory aggregate material is considered in detail.

Jan 1, 1950

By A. C. Fraker, H. H. Stadelmaier

WIENER and Bergerl reported the existence of the nitrides Fe3NiN and Fe3PtNwith a cubic L1'2 structure. The present note shows that a similar nitride Fe3PdN can be observed and that the composition range between the iron nitride Fe4N and the nitrides Fe3NiN, Fe3PdN, and Fe3PtN is occupied by single-phase cubic nitrides with structures intermediate between L1' and L1'2. The materials used in this investigation were electrolytic iron of 99.9 pct purity, carbonyl nickel of 99.7 pct purity, sponge platinum of 99.95 pct purity, and palladium sheet of 99.8 pct. purity. Binary alloys of the transition metals were induction-melted in a crucible of fused alumina, powdered, and screened to a particle size of - 200 mesh. The powders were nitrided at 600°C in a gas mixture of ammonia and hydrogen, and the crystal structure was determined with the aid of a Wilson powder camera. The results are compiled in Table I together with information from the paper of Wiener and Berger.1 The compound at the nominal composition Fe3PdN has a diffraction pattern with prominent reflections of a face-centered cubic lattice (h2 + k2+l2 = 3, 4, 8, 11, 12, 16) and weaker superstructure lines (h2 + k2 + 12 = 1, 2, 5, 6, 9, 10, 13, 14). With decreasing palladium content the superstructure lines become weaker and approach the intensity of those of Fe4N. No analysis was made of the intensities, but it can be assumed that the structure is that found by Wiener and Bergerl in Fe3NiN and Fe3PtN, namely L1'2 (perovskite structure) with both palladium and the interstitial nitrogen fully ordered. The dependence of the lattice constant upon the solute atom (Ni, Pd, Pt) content can be explained tolerably well by simple lattice expansion due to subsequent work confirms this suggestion, it will be of significance to order-disorder theory. The author is grateful to Lester Guttman for discussions on this topic.

Jan 1, 1961

By E. L. BROKENSHIRE

FLUORSPAR, a little known non-metallic mineral, referred to technically as fluorite, chemically as calcium fluoride, is a compound of calcium and fluorine in the ratio of one molecule of calcium to two of fluorine. By weight it is composed of 51.3 per cent of calcium and 48.7 per cent of fluorine. Its specific gravity is 3.2. It is brittle, has a hardness of four and can be easily scratched with a knife. It weighs about 200 Ib. per cubic foot and has a melting point of 1650" F. The color of fluorspar ranges from pure white and opaque white, according to its purity, to various hues of yellow, green, pink, lavender, blue and brown, to bluish black. Although the lumps have color, when ground the fluorspar becomes pure white. The reason for this is because the mineral usually carries no fixed pigment, the color being produced by the re- fraction of light rays within the crystal structure and small quantities of organic matter which readily oxidizes. It crystallizes in the isometric system with perfect octahedral cleavages.

Jan 1, 1929

By M. J. Sinnot, J. C. Shyne

Low-frequency mechanical damping measurements were made to investigate internal friction in Fe-A1 alloys. The atomic ordering of the Fe-A1 system strongly influenced the stress-induced ordering internal friction. Magnetoelastic damping was also encounteyed and was shown to be reduced by the application of a static stress. THIS paper describes some damping experiments made on alloys of Fe and Al. Stress-induced ordering internal friction was measured with samples containing from 9.8 to 31.3 at. pct Al. Aluminum is soluble in a-Fe to about 50 at. pct and forms at least two long-range ordered structures, Fe3Al and Feu.' Stress-induced ordering internal friction is known to occur in many substitutional solid solutions, but few measurements of this damping effect have been made with alloy systems that have pronounced ordering tendencies. LeClair and Lomer developed expressions relating the relaxation strength of the damping process to the degree of atomic ordering and predicted that stress-induced ordering internal friction would be zero with complete ordering.' This concept was confirmed experimentally by Lulay and Wert using the system cd-Mg It is also consistent with the weak stress-induced ordering peaks observed in P -brass by Artman and in 16 wt pct Al Fe-Al by bert.' It was expected, therefore that the ordering characteristics of the system Fe-Al would strongly influence the stress-induced ordering internal friction exhibited by the experimental alloys. SAMPLE PREPARATION The alloys used in this investigation were induction melted under vacuum using high-purity melting stock. The iron was electrolytically refined Plastiron 101 which contained 99.85 wt pct Fe. The aluminum was a special 99.95 pct pure grade supplied by Alcoa. The only other raw material was spectrographically pure graphite which was used in small quantities as a deoxidant. The amount of carbon used was slightly in excess of the amount required to completely deoxidize the melt; this resulted in residual carbon contents of 0.01 to 0.02 pct in the finished alloys. The vacuum cast 2 1/2-in. diam ingots were hot rolled to 5/8-in. diam round bars. Portions of these bars were hot swaged and hot drawn to 0.050-in. diam wire. Straight pieces of the hot drawn wire were slowly heated to a temperature of 1300°C in a He atmosphere. After holding for 4 hr, the samples were allowed to cool in the furnace. This annealing treatment resulted in grain growth in the samples, the final grain size being about the same as the wire diameter. The grain boundaries were oriented perpendicularly to the wire axis, giving a bamboo grain structure. The existence of a preferred orientation could not be detected in these coarse grained samples. If the samples had a fiber structure, this probably would have been the same in all samples because of similar processing, thus the influence of crystal orientation on the relaxation strength would have been similar in all samples. The aluminum contents of the alloys are listed in Table I. EQUIPMENT The principle of the torsion pendulum was used for the internal friction measuring device. The

Jan 1, 1961

By Virgil R. D. Kirkham

RECONNAISSANCE of a part of southeastern Idaho and small strip of western Wyoming lying between longitudes 111° and 111° and 45' W., and latitudes 43° and 43° and 30' N., comprising an area of approximately 1330 sq. mi., was undertaken during the summer of 1923 for the collection of data regarding the oil possibilities of the region. TOPOGRAPHY, SETTLEMENT, AND ACCESSIBILITY The entire area lies within the upper Snake River drainage basin. Snake River flows through the northeastern and eastern part of the area in a northwesterly direction. The entire drainage system has been controlled by the structure of the sedimentary beds in the area, which exhibit numerous alternations of hard and soft strata with consequent unequal erosion. The headwaters of the most important streams, as well as many others, flow in a northwesterly or southeasterly direction along

Jan 1, 1925

By Charles Behre

THIS paper deals with recent geologic studies in the slate belt of Northampton, Lehigh and Berks counties, Pennsylvania. The work was conducted under the auspices of the Pennsylvania Topographic and Geologic Survey. Three years have now been spent in detailed consideration of the economic geology of this region. In the field, particular attention was paid to the bearing of geology on quarry development and property valuation and the object of this paper is to summarize the results from that viewpoint. Excellent studies of a somewhat similar nature have already been carried out by Bowles,1 but with the emphasis upon the details of quarrying and fabricating methods, rather than upon the geologic relations. THE NORTHAMPTON-LEHIGH-BERKS DISTRICT Location The region here discussed lies in east-central Pennsylvania and extends southwestward from Delaware River, on the New Jersey line, to the Schuylkill in north-central Berks County. It is an elongated belt occupying the northern sections of the three counties mentioned and lying along the southern edge of Blue Mountain. Its length is about 50 miles and its average width five or six, though in places it attains a maximum of 10 miles.

Jan 1, 1928

By ALEXANDER S. CORSUN

THE main orebody in the Hecla mine, Burke, Ida- ho, occurs along a nearly vertical shear zone in the Burke quartzite, with a substantial gouge and lamprophyre dike occurring in an irregular manner throughout the lode. The veins range from 3 to 40 ft. wide and dip from 70 deg. to 90 deg. There is 110 definite line of demarcation between the lode and the wall rock. Stringers of ore are often found in the wall rock for irregular distances. Horizontal but irregular quartz stringers are also found running into the walls and positions of the wall have a tendency to break to the quartz stringers and the accompanying gouge, which causes indefinite, uneven and extremely heavy side and top pressures.

Jan 1, 1930

By John Henry Harden

WITH imperfect instruments it is impossible to make accurate surveys; the results are inaccurate maps, with their attendant consequences. The design of the writer is to describe an improved form of tripod head, and certain defects in an English transit and a miners' dial, with the method taken to remedy the defects of the transit. When the present transit superseded the surveyor's compass, there was one special objection brought against it, and with some show of reason ; namely, that the tripod of the compass with its ball and socket motion, allowed a quicker levelling-up (and, consequently, more work) than was possible with the transit. To this objection it was replied, that the ball and socket would not allow the instrument to be levelled with the same degree of precision that could be attained with the levelling screws, and that if time was sacrificed greater accuracy was attained. Nevertheless, it is a well-known fact that in this country, and especially in England, the compass or miners' dial holds its ground solely from its rapid adjustment. Ever since the introduction of the transit, efforts have been made to give to this instrument the same facility of levelling possessed by the compass or dial, and the same means have been tried, i. e., a . ball and socket motion, since a modification of this in some form was the only method that would answer. The upper part of a transit is, however, much heavier than the corresponding parts of a compass, and, therefore, requires more binding power, which cannot be ob¬tained with an ordinary ball and socket joint. It has been a study with instrument-makers to combine the facility of these two tripods -the quickness of the ball and socket with the steadiness and accuracy of the screws; but in all attempts in this direction the ball and socket of the compass has been literally followed, the entire stability of the instrument depending upon the friction of the ball in its socket. There is great need for a tripod that can be more easily manipulated than the present form, for it rarely happens that an engineer has a level surface on which to set his instrument, and very often

Jan 1, 1879

By D. W. Fuerstenau

Recently R. J. Charles1 showed that comminution of brittle or semi-brittle materials in batch operations is described more appropriately by a variable energy relationship than by the specific relationships proposed by Rittinger,2 Kick,3 and Bond.' That is, the value of n in the empirical differential operation which applies to crushing and grinding (Eq. 1) is variable. Independently, Holmes' developed an identical generalized equaton for size reduction. The experimental data of Charles and Holmes show that the value of n is determined by the material and the comminuting machine and is constant for a given combination of these two conditions. The general objective of the present article is to extend the Charles-Holmes concepts to continuous ball milling. The specific objective is to analyze the operation of a vibratory ball mill dry-grinding chromite in a continuous open circuit and to develop an equation for the comminution of chromite in this mill. Basic Principles: In a batch mill the length of time during which the material is ground is a direct measure of the energy expended on the material, except possibly for exceedingly fine grinding. However, in a continuous operation, the fraction of the total expended energy which is useful for grinding will vary according to feed rate and amount of material in the mill. If the amount of material within a continuously operating vibratory mill is low enough so that only part of the expended energy is used for grinding, the extent of size reduction at constant power input must depend upon the length of time the material is retained within the mill, namely, upon retention time. The following analysis pertains to a continuous mill operating under these conditions. The empirical differential equation that applies to the comminution of brittle materials is:" dE = -Cdx/x" [1] where dE is an infinitesimal energy expenditure, C a constant, dx an infinitesimal size change, x the particle size, and n a constant. For continuous grinding in an open circuit at constant power input, P, Eq. 1 must be written as (dtr)P = -C dx/x" [la] where dt, is an infinitesimal time during which a particle of size x is in the mill, and C' is a constant. A ground product never consists of particles of single size but always comprises a distribution of sizes. In comminution, the expenditure of energy causes a lateral shift in the size distribution.', ' " The general objective of any engineering study of comminution is to correlate the magnitude of this size distribution shift with the energy expended, the ultimate aim being to cause the greatest shift with the least amount of expended energy. Although a number of criteria can be used to measure this shift, Schuhmann's size modulus has been found convenient.' Mathematically, the Schuhmann size distribution can be expressed as follows:" y = l00(x/k) [2] or in differential form: dy = [F- xa-' dx ] K, where y is percentage of material finer than size x, a is a constant that determines weight distribution among particles of various sizes, and k the size modulus that denotes the theoretically maximum-sized particle in any size distribution. By considering the energy required to reduce an element of weight of material, dy, from size x, to size x, the element of time during which the material must remain in the mill at at power will be (dt..).= J'-Cax!(dy) [3] Summing up all the elements of weight from zero to 100 for a product that conforms to the Schuhmann size distribution yields C C f Cdx,\( 100«x°-'dx\

Jan 1, 1960

By AIME AIME

IN an address before the New York Section. A.I.M.E., Oct. 20, Alex L. ter Braake, speaking on the tin industry of the Netherlands East Indies, interjected a few remarks, at the chairman's request. on the mineral stock-piling project now before Congress in a bill sponsored by Senator Scrugham. The full text of Mr. ter Braake's paper was published in the Nov. 6 issue of the American Metal Market. Following mention of the buffer stock scheme as applied in the tin industry, Mr. ter Braake continued:

Jan 1, 1943