Search Documents

By Joseph A. Holmes

I. INTRODUCTORY. THE plans for the investigation of fuels and structural materials now being conducted by the Technologic Branch of the United States Geological Survey were, before being decided upon by the Director of the Survey, submitted for consideration to the National Advisory Board, upon which there are nine representatives from the membership of the American Institute of Mining Engineers, viz.: Messrs. John Hays Hammond, Robert W. Hunt, B. F. Bush, and E. V. d'Invilliers (representing the Institute); Messrs. Julian Kennedy and C. S. Robinson (representing the Iron and Steel Institute); Dr. Charles B. Dudley (representing the American Society for Testing Materials); Mr. F. H. Newell (representing the U. S. Reclamation Service); and Dr. Richard Moldenke (representing the American Foundrymen's Association). It seems fitting, therefore, that a report of these investigations of the past three years should be submitted to the Institute for publication in its Transactions. The above, together with other representatives of the national engineering societies and allied organizations, were invited by President Roosevelt to serve, along with the Chiefs of the several Government Bureaus who have charge of public works and large. fuel purchases, on the National Advisory Board to give advice concerning these investigations. The appointment of this National Board grew out of a wish on the part of the President, the Secretary of the Interior, and the Director of the Geological Survey not only that the appropriations for these investigations be expended in a manner most beneficial to the several branches of the government

Jan 7, 1908

By Thomas L. Kesler

IF all of the 14 million tons of kaolin produced in Georgia through 1949 had been mined from a single deposit 20 ft thick, it would represent a mined-out area of less than 1 sq mile. This measure of depletion is in such strong contrast with the large size of the area shown in Fig. 1, from which most of the output has come, that there has developed an optimistic outlook concerning future supplies of kaolin equal in grade to that already mined. Dozens of mines are widely but not evenly distributed within this area, which consists mostly of parts of Twiggs, Wilkinson, and Washington counties. There are scarcely half a dozen kaolin mines elsewhere in the state that have been appreciably productive, although the areas in which they occur may have good possibilities. Most of the efforts to find new deposits, therefore, will be confined to the area shown in Fig. 1, for it is here that the industry has established its facilities, and prospecting is encouraged by relatively numerous outcrops and opened deposits of kaolin.

Jan 10, 1951

By A. K. Sinha

The market for thermal coal has recently been growing rapidly and it is projected to continue to do so in the foreseeable future. Both the national and international markets often demand high-Btu low-sulfur thermal coal in order to minimize the cost of utilization and meet the environmental restrictions. High quality thermal coal can be prepared to compete in the utility market by desulfurizing the high-Btu midwestern coal and blending it with low-sulfur western coal which is usually low in Btu content. The methods that can be used for optimizing the coal preparation plant operating parameters for physically desulfurizing coal are presented.

Jan 1, 1985

By JAMES A. VEASEY

SINCE the World War, excepting for a few brief periods of relief, the American petroleum industry has been obliged to meet its important economic responsibility to this nation hampered by the maladjustment that inevitably follows a marked and unwholesome over-production of its raw material, crude oil. Despite the warnings of the Federal Oil Conservation Board and the endeavors of many of the leaders in the business to stem the flow of oil from the wells of the country, the evil ,not only persists but, at the moment, seems more malignant than ever before. Unless the local and temporary restraints on drilling and production now in effect in California, Wyoming, Texas, and Oklahoma are continued, and, indeed, unless stricter and more comprehensive measures of the same sort are imposed and adhered to by the industry in those States, over-production in the enterprise during the current year will be more pronounced than in any other period in history.

Jan 1, 1929

By Allen J. Johnson

With a realization of the rapidly increasing importance of automatic stokers as a medium for domestic heating, the Anthracite Institute Laboratory has conducted extensive investigations, over a period of several years, to determine the various outstanding characteristics of stoker design and performance. The purpose of this paper is to summarize these findings as a guide to current practices. Stokees Investigated One or more models of the underfeed stokers listed below were included in the various phases of this investigation: Beckley Gilkoal Burnwell Iron Fireman Combustioneer Motor Stokor Electric Furnace Man Norristown Super-stoker Erie Heat Generator Whitney Fire Ball (Tests Incomplete.) Fuel Saver Principles of Construction.—The operating principle of the leading makes of underfeed stokers is similar (Fig. 1). A plunger1 or slowly revolving worm2, conveys the buckwheat or rice sizes of anthracite to the center of a specially constructed tuyere pot where air is admitted to the coal through suitable ports of varying design. As the fuel burns, it is slowly forced to the outside circumference of the tuyere by the pressure of the incoming coal; eventually the ash falls over the edge of the pot, either entirely by gravity or aided by mechanical sweepers. In at least one model, the entire firepot revolves. While various special details have been included in the design of a number of stokers, they do not affect the general principles as described above, and therefore have not been included in this discussion.

Jan 1, 1936

By Allen J. Johnson

With a realization of the rapidly increasing importance of automatic stokers as a medium for domestic heating, the Anthracite Institute Laboratory has conducted extensive investigations, over a period of several years, to determine the various outstanding characteristics of stoker design and performance. The purpose of this paper is to summarize these findings as a guide to current practices. Stokees Investigated One or more models of the underfeed stokers listed below were included in the various phases of this investigation: Beckley Gilkoal Burnwell Iron Fireman Combustioneer Motor Stokor Electric Furnace Man Norristown Super-stoker Erie Heat Generator Whitney Fire Ball (Tests Incomplete.) Fuel Saver Principles of Construction.—The operating principle of the leading makes of underfeed stokers is similar (Fig. 1). A plunger1 or slowly revolving worm2, conveys the buckwheat or rice sizes of anthracite to the center of a specially constructed tuyere pot where air is admitted to the coal through suitable ports of varying design. As the fuel burns, it is slowly forced to the outside circumference of the tuyere by the pressure of the incoming coal; eventually the ash falls over the edge of the pot, either entirely by gravity or aided by mechanical sweepers. In at least one model, the entire firepot revolves. While various special details have been included in the design of a number of stokers, they do not affect the general principles as described above, and therefore have not been included in this discussion.

Jan 1, 1936

By Charles R. Holmes

MORE than 70 igneous pipes and dikes are known to occur in Cambrian sediments throughout an approximately circular area of about 75 sq miles in southwestern Ste. Genevieve County and southeastern St. Francois County, Mo., across the southern portion of the Farmington anticline, which is outlined in fig. 1. From evidence obtained from fossil fragments taken from some of the intrusive, and from the similarity in composition of the more basic intrusives to those of known age in surrounding states, these pipes and dikes are believed to be at least post-Devonian and probably Cretaceous in age. As first postulated by Rust, these intrusives are believed to represent explosion tubes, or diatremes, punched through great thicknesses of solid rock by gaseous pressure. The particular intrusive studied is located about 1 mile north of the small town of Avon at an elevation of 880 ft in the EM SES NE% of sec. 2, T. 35N, R. 7E. Outcrop is through the Bonneterre dolomite in two separated exposures. The larger outcrop extends east and west for about 50 ft along a tributary in a small ravine (fig. 2). The smaller exposure occurs as a few scattered patches over an area 20 ft square about 100 ft to the north. The area between the exposures is covered, but scattered patches of the Bonneterre dolomite outcrop throughout the area surrounding the diatreme. Where exposed, contact relations show the surrounding dolomite to be shattered and metamor- phosed to a fine-grained rock for a distance of 15 to 20 ft from the intrusive. The igneous rock occurs as a dark greenish-gray porphyry near the center of the diatreme and as a fine-grained, greenish-gray material containing lapilli and metamorphosed fragments of dolomite near the contact with the country rock. The most abundant original mineral of the porphyritic rock is olivine now largely serpentinized as the result of extensive hydrothermal alteration at time of emplacement. The most common constituent of the fine-grained rock, which occurs near the border of the intrusive, is calcite. Mica is a common constituent of both types of rock, occurring as tufts or

Jan 1, 1950

By R. W. Kraft, L. D. Graham

The process of' spheroidization, or more properly coarsening, of Al-CuAl,eutectic alloy specimens with various initial microstructures was studied by quantitative metallographic and X-ray diffraction techniques. By measuring the rale at which specimens with a very fine dispersion of phases (produced by quenching molten droplets of the alloy in water) coarsened it uias determined that the rate-controlling mechanism for coarsening was diffusion, probably of aluminum in the aluminum-rich phase. The lamellae in specimens with a high degree of microstructural and cr-ystallog/uphic anisotropy (produced hy unidirectional solidification of ingots) thickened during heat treatment by recession of the CuAl, platelets from jaulted regzons, yet the specinlens retained a very high degree of. anisotropy after prolonged heat treatments at a temperature within 8°C of the eutectic temperature. In such specimens the crystallographic orientation relationship between the phases remained constant and no change in the crystallographic substructure occurred. Based on these observations a model was developed for the coarsening—or rate of' thicken-ing—oj- the lamellar structures which predicts that the rate of decrease of interface area is proportional to the square of lamellar interface area. Experiments with degenerate and very coarse lamellar microstruc -tures preduced by extremely slow unidirectional solidification) indicate that initial microstructure is a most important factor governing the final micro-structure after heat treatment. The particle size and shape of dispersed phases are important parameters affecting the properties of a wide variety of two-phase materials. As is well-known, varietythe dispersed-phase particles tend to coarsen at appropriately high temperatures because the interface energy of the system is reduced by the concomitant reduction in interface area. The phenomenon of

Jan 1, 1967

By F. E. Bachman

Although it has been apparent to me for a long time that too great weight was currently given to the silicon-contents of foundry-iron, and that the theory of the control by silicon of the carbon-contents of cast-iron is unsound, or that, at best, the influence of silicon is too small to be of much practical value as a guide in foundry-work, it never seemed to me desirable to enter the lists against either the " silicon-fad " or the theory, for the reason that I had neither the time nor the facilities to prove my position, nor any better theory to offer. But since Mr. Summers has taken the step, it seems but right that I should give such facts as are at hand in support of his contention. At the same time I do not think these are enough to prove the case if the contrary proposition were not itself, as it seems to me, based on insufficient evidence. Both Keep's and Turner's conclusions seem to be drawn from irons carrying less than the normal amount of carbon; Turner's " base " being, moreover, a steel rather than a pig-iron, and both the white base and the ferro-silicon of Keep being so low in carbon that compounds of them would not give a material approaching the carbon-contents of a normal casting, and having, therefore, little value as showing the effects of silicon on foundry-irons, even if his samples were treated under the same conditions as those to which pig-metal is subjected in making castings.

Jan 1, 1899

By J. B. Austin

IN considering so complex a process as the smelting of iron in the blast furnace, there is obviously no single method of calculating efficiency that gives a complete appraisal of the performance of the furnace in all its several functions; such a comprehensive view as is required to evaluate producing ability and manufacturing costs for a given furnace is obtained only by considering a group of efficiencies, each of which measures the performance of the furnace from a specific point of view. For instance, there is the rate of consumption of coke per ton of iron produced, which is probably the most frequently considered, and is certainly one of the most important of the group; there is the efficiency of recovery of iron charged; and there is the efficiency of utilization of energy, both chemical and thermal, in some respects related to the former two yet in other ways independent of either. In each of these cases, the calculation can be made on the basis of the actual input of material or energy, or it may be based . upon a comparison with the minimum amount of material or energy that would be required by a "perfect" furnace; that is, an imaginary ideal furnace analogous to the perfect steam engine used in thermodynamic calculations, when this furnace is operating under optimum conditions. Moreover, the furnace itself can be considered either as an apparatus for smelting iron or, taking a somewhat less common point of view, as a gas producer yielding iron and slag as by-products. Some of these effi-ciencies are more useful than others, yet all are instructive; for a knowl-edge of them not only leads to good engineering practice from the standpoint of control but also discloses limits to possible improvement in performance and indicates the lines along which improvement is most likely to be profitable. Estimates of some of these efficiencies have appeared from time to time in the literature, but many of them are open to objection because they are based on data of uncertain accuracy or because they have been calculated without due regard to the thermo-dynamic principles involved. Moreover, so far as the author is aware, no general survey of the blast furnace comparing its performance in all the aspects mentioned has been made.

Jan 1, 1938

By J. A. Woolf, E. S. Leaver

The presence of soluble base metals in precious-metal ores usually precludes cyanidation as the best method of treatment. The laboratory experiments described in this paper show the possibility of cyanidation of gold-silver ores containing less than 0.5 per cent. of cyanide-soluble copper and the effect of zinc in the cyanide solution. Part I.—Copper in Cyanidation The proposed process of cyanidation of precious-metal ores containing copper is based on the regeneration of about 80 per cent. of the cyanide used in the dissolution of the copper. The method of regeneration involves a combination of the sulfide and the acid precipitation of the copper and silver. The resultant solution is made alkaline with lime, and the gold is precipitated with zinc dust. Solubility of Copper Minerals in Cyanide Solution In order to determine the solubility of copper minerals, including metallic copper, under the usual conditions for cyanidation, experiments were conducted with synthetic ores. Each ore sample was prepared by mixing the particular pure copper mineral with barren sea sand. Both the mineral and sand were ground to pass 100 mesh before they were thoroughly mixed. The percentage of copper in each head sample was determined by direct assay, excepting the metallic copper sample, which was computed on weights before mixing. Table 1 gives the results. Azurite, bornite, chalcocite, cuprite, malachite and finely divided metallic copper are readily and completely soluble under the usual conditions for cyanidation. Enargite and tetrahedrite are sufficiently soluble to cause an excessive loss of cyanide, and they also cause fouling of solutions with arsenic and antimony. Precious-metal ores containing small percentages of chalcopyrite or chrysocolla may give satisfactory returns with the usual cyanidation.

Jan 1, 1930

By E. W. Dewing

The nature of solid solutions of sodium in non-paphitic carbon at temperatures near 1000°C has been investigated by an electrolytic technique. The activity coefficient is found to vary strongly with the heat-treatment temperature of the carbon, and an analysis of the energy terms involved suggests that this is due to variations in the Fermi level. The diffusion coefficient for sodium is in the range implying that the sodium atoms (or ions) are not bound to specific sites on the carbon, in agreement with lack of evidence for specific compounds in the activity -composition curves. In the light of These results phenomena occurring in aluminum reduction cell linings are dis-cussed. It is concluded that sodium migrates by diffusion through the carbon lallice and not the pores, and that A14C9 is formed within the lining hy The excess of NaF invariably found in used linings is formed by this reaction and by air oxidation: There has recently been much interest in the swelling of carbon which occurs when it is made cathodic in an aluminum electrolysis cell, and there is general agreement that the phenomenon is due to the penetration of sodium atoms, derived from the reaction on the carbon lattice. (NaF and AlF3 are constituents of the fused-salt electrolyte.) The low-temperature lamellar compounds of potassium with graphite are well-known, and one compound between sodium and graphite has been reported.4 There is, however, virtually no information on the basic chemistry of the interaction of sodium with nongraphitic carbon at high temperatures, although Dell3 has made some fundamental studies of rates of penetration. At the time the present work was carried out these were not available. Rapoport and samoilenkol had measured rates of physical expansion in a dilatometer, using the fractional increase in length of a carbon specimen after electrolysis in a cryolite bath for 2 hr as an index of susceptibility to cathodic swelling. Work here with a similar apparatus showed that expansion (of a 1.5-in.-diam cylindrical specimen) ceased in less than 20 hr, and that the final expansion was much more reproducible than the value at some intermediate time. This suggested that an equilibrium was being set up, and that a thermodynamic approach was required. The results obtained are not as accurate as had been hoped, but they are the only ones of their type available and have enabled useful conclusions to be drawn. The experimental work was divided into two parts: an investigation of the activity-concentration diagram for sodium in carbon, and a rough determination of the diffusion rate. For the former, most of the experiments were made with petroleum coke even though this is not a form of carbon used in cell linings. It has the advantages, however, that it is a homogeneous material, that it is low in ash, and that its structure is reasonably well understood. Anthracites and coal cokes gave results of the same type as obtained with petroleum coke, but the reprodu-cibility from specimen to specimen was extremely poor. EXPERIMENTAL 1) The Activity-Composition Diagram for Sodium in Carbon. The petroleum coke was ground, pressed at 40,000 psi into plates 19 by 9 by 2 mm without added binder, and heat-treated. The sodium activities were established by an electrolytic technique. The carbon was made anodic in a cryolite bath with an aluminum cathode, and a controlled potential, E, applied so that the sodium activity at the anode was given by ln Na = 1n asa - EF/RT [21 where as, is the sodium activity generated by Reaction [I]. The relative activity is sufficient for many purposes and is simply given by The value of Na not at present known, but when the thermodynamics of the Na-A1 system have been worked out it can be derived from the equilibrium

Jan 1, 1963

By E. B. Swanson

There is only one way to transport natural gas and that is by pipe lines. In the past few years, these lines have been extended rapidly into areas which previously had been served mainly by solid and liquid fuels. In the subject given me, this extension is referred to as an invasion, which implies a rather forceful entry. Whether or not such an implication may be applied to recent natural-gas developments is unimportant. It is the fact of the extension, not its definition, which is important. For centuries, natural gas has been utilized for various purposes in many parts of the world. It was the foundation of fire worship at Baku. The Chinese used it for the evaporation of brine in salt manufacture. In our country, its history seemingly dates back 110 years to the vicinity of Fredonia, N. Y., where seepage gas was assembled and used for lighting purposes. A few years later, a %inch pipe was laid to a lighthouse on Lake Erie, and the early records of the Lighthouse Service tell of the difficulties surrounding this use. With the discovery of oil in Pennsylvania, there followed further development; the town of Titusville was piped with natural gas and, some few years later, gas was made available for manufacturing plants adjacent to the oil fields. For more than a half century, the industry was concentrated in the

Jan 1, 1932

By R. J. Brown

Design of a submarine pipeline system is governed by many factors, one of which is the effect of transverse horizontal currents on the pipeline structure itself Although this feature alone can be of utmost importance to the life span and stability of the underwater pipeline, it is usually the least recognized, with these hydro-dynamic forces being either completely overlooked or grossly underestimated. In an attempt to supply the methods and means for stabilization of sub-marine pipelines, much capital has been spent by pipeline companies. Design criteria incorporated by these organizations extend over a broad spectrum of engineering with bases varying from pure theory to cut and dry methods. A history of numerous failures has substantiated the postulate that many of these submarine pipelines have been underdesigned from the stability standpoint. By the same token, equally as many have been excessively overdesigned with resultant excess expenditures. An attempt has been made in this paper to establish the magnitudes of these hydrodynamic forces by measuring the lateral current-induced differential pressure distribution around the periphery of the submarine pipeline. INTRODUCTION The expenditure of money for research by corporations obviously requires beneficial results to justify the investment. One of the functions of the engineer is first to make the problem known and then to provide a means of solution at the least possible cost. The initial procedure is to investigate all pertinent published technical articles on the subject to determine if this problem has been previously solved. If resolution of this problem is not obtainable, the next course of action is to evaluate through experiments these forces and their magnitudes. On the specific subject of drag and lift, the accumulation of data is provided from three separate and distinct sources: from experience, from theoreticians and through experimental observations. The experience source has proved costly with money wasted either because of underdesign and failure or excessive expenditures for overdesign, and has not been sufficient to form a definite conclusion on these hydrodynamic forces. The pure theoretician is often not completely cognizant of the situation and his works bear little adaptation to the real problem. The experimentalist has his own problems with regard to obtaining results from small-scaled models and successfully adapting them to the larger prototypes. Each method has its own advocates who diligently adhere to their own separate routes as being the only means of resolving this problem. However, a review of the various methods of analysis leads one to the conclusion that if the advantages of all three are combined, a reasonable solution to this problem can be reached. Briefly then, the problem is to obtain the magnitudes of the forces on the submarine pipeline subjected to a lateral current by investigations of previous design considerations, by a study of existing theoretica1 data and by appropriate experimentation. This paper deals mainly with obtaining experimental data and the interweaving of theoretical and experience factors for resolution of these forces. APPARATUS AND PROCEDURE These tests were performed in 1961 at Collins Construction Co.'s main office near Port Lavaca, Tex. Test equipment consisted of a steel tank 3 ft high by 4 ft wide by 40 ft long, with several pumps circulating the water through the tank via suction lines from the downstream portion of the tank and discharging from the pumps directly into the upstream end of the tank. For reduction of turbulence, a wire section was constmcted in the upstream portion and straightening vanes in the form of pipes, screens, etc., were used to reduce the vortex and eddy action in the tank (Fig. 1). A venturi was built at the test specimen for obtaining velocity sufficient to simulate actual conditions. This full-scale test was initiated to eliminate the error introduced in modeling and obtain a truer picture of forces actually encountered. Six- and 10-in. specimens were prepared by

Jan 1, 1967

By R. H. Wightman, G. H. ADAM

In order to secure good results in the prevention of accidents, it is generally recognized that the desire for such accomplishment, as well as the aggressive and constructive action to achieve it, must emanate from the Top Management and permeate successively down through the "Chart of Authority" to the workmen. Several years ago, with the above as a basis and with full support of the Top Management, the Mining Department started a program of selling the foremen and bosses the idea that safety could be achieved and that it was desired and required. Using psychology, persistence and numerous other methods, the foremen and bosses were finally impressed with the idea that "It can be done" and "It will be done." With this in mind, new ideas were brought forth by the foremen and bosses regarding the caving operation and the specific jobs in the operation. These new ideas were taken up in round-table discussions and resulted in certain changes in the undercutting method and the actual drawing of the blocks. These changes resulted in increasing fragmentation of the blocks which prevented the usual hang-up areas in the blocks. With the rock smaller in size and within reasonable reach from the tapping drifts, accidents were prevented in the tapping section. At the same time, an enforced campaign of housekeeping throughout the mine was undertaken with very beneficial results. The foremen and bosses then, in turn, educated and trained the workers themselves to become safely conscious. In so doing, a constant re- minder was given on all jobs assigned that the job was to be done safely as well as efficiently. No man is assigned a job who is not qualified for the type of work required. Efficiency and safety go hand in hand.

Jan 1, 1949

By Irving B. Cadoff, Stojan M. Zalar

AgInTe2, CuInTe2, and all Proportions of CuxAg1-xInTe, forMed homogeneous single phase alloys after direct solidification from the nielt. X-ray analysis indicated a zinc-blel~de strzccture typical of the chalcopyrite compounds, and the electrical resistivity and Sccbeck coefficient values were in the semiconducting range. AuInTe, and AuxA4g,-, InTe, formed by what appeared to be a peritectic reaction (the thermal analysis curves showing more than one arrest) and were conseyue~ztly polyphase. Substitution of copper into AgIrzTe, resulted in a continuous transition in the room tenzperature Seebeck coefficient from the negative AgIzTe, to the positive CuInTe,. A zero coefficient was obtained at about Cuo.55 Ago.45 InTe, . The temperatzire variation was similar to that observed for the stoichiometric compounds, that zs, tendency towards "p" concEuction at elevated temperatures. The thernzoelectric figure of merit for the compo~uzds, as determined by the Putley -Harmnn method were in the range 10- to 10-7 "K-l; the thermal conductivities in the order of 0.15 cal per sec-cm-oK. INCREASED interest in semiconducting intermetallic substances is expanding much of recent research from simple binary compounds into polyatomic systems and solid solutions. Ternary compounds A' represent a covalent extension of the binary semiconductors Within the a tin isoelec-tronic series, Ag-Cd-In-Sn-Sb-Te-I, divalent cadmium atoms in CdTe are being substituted for by monovalent silver and trivalent indium atoms to form the compound AgInTe, . By cross-substitution with elements of other isoelectronic series, a great number of ternary compounds A 'B"'c? is possible. In all of them, however, a necessary though not sufficient condition for the covalent, semiconducting bond—that there be four sharing orbital electrons per atom—must be fulfilled. In AgInTe,, each silver or indium atom is tetrahedrally surrounded by four tellurium atoms, while each tellurium atom is co-valently bound to two silver and two indium atoms. Synthetic chalcopyrites A'B"'c~ were first recognized as potential semiconduct&rs by Goodman and Douglas.' Austin, Goodman, and Pengelly discuss preparation difficulties and some electronic measurements on AgInS, , AgInSe, CuInSe, , AgInTe, , and CuInTe,. Chalcopyrites A B c2v are mentioned in papers attempting to classify and predict semiconducting behavior of intermetallic compounds; on the basis of saturated tetrahedral sp3 bonds,3 by specific selection criteria,' and by crystallographic considerations."

Jan 1, 1962

By J. V. W. REYNDERS

FIRST of all let me express my affectionate gratitude for the cordiality and good will of your reception. On the part of the men I venture to interpret the character of your greeting, not only as a recognition of the position to which you have been good enough to elect me, but also as an expression of your friendly attitude. However, I cannot pass over the tribute of the ladies so casually: Nor does it seem possible to do justice to my sentiments in addressing them collectively. I would feel more equal to the task if I could have the opportunity to talk to them singly, in doing which I know I may count upon their good sportsmanship not to compare notes. There has been some discussion between Mr. Kelly and myself as to our respective duties on this occasion: The precedents are not clear as to whether the retiring or the incoming president is expected to speak at length. Mr. Kelly's argument was that as the incoming president confines himself to promises for the future his field is a broad one and his opportunities for extending his remarks correspondingly unlimited.

Jan 1, 1925

By Fred R. Ingram

FOR the purpose of this discussion, let us consider that the Rocky Mountain region covers the area in the seven Mountain States, Idaho, Montana, Wyoming, Utah, Colorado, New Mexico, and Arizona, and before we discuss the needs of these states, let us define Industrial Hygiene. Industrial Hygiene is that branch of preventive medicine concerned with the protection of health, improvement of efficiency, and prolongation of life of the industrial worker; in short, adult health conservation. It includes in its broad meaning not only the prevention of occupational diseases, such as silicosis, lead poisoning, cadmium poisoning, and many others, but such relative problems as overcrowding, fatigue, and personal and mental hygiene; exposure to abnormal temperatures, pressures, and humidities; ventilation, heating, and lighting. It is a science which requires the combined activity of medical personnel (doctors and nurses), engineers, and chemists to evaluate the exposures and determine the means of eliminating the hazard. The engineer surveys the workplace, takes air samples at the breathing level of the workman, and analyzes the work exposure. The chemist determines in his laboratory the exact amount of toxic material collected in the sample, which represents the exposure of the workman. The doctor must diagnose the occupational disease, recognize its cause, and evaluate the disability. Together, all three must correlate the data obtained and devise efficient methods, medical or engineering or process changes, for controlling or minimizing the dangerous condition and for studying the effectiveness of these measures. The plant doctor, in addition, must aid in the readjustment of the incapacitated worker and provide facilities for prevention. Industrial hygiene, however, is of no avail without the understanding co-operation of management.

Jan 1, 1945

By I. R. Kramer

The stress associated with the surface layer was deter-minedfor iron and molybdcnum. These measurements show that the surface layer plays a very important role in the plastic deformation of bcc metals. From the relationship between strain arui the surface layer stress and the back stress imposed by the internal obstacles, it is Proposed that the term of of the Hall-Petch equation is related only THE large number of studies on plastic flow of bcc metals have failed to delineate clearly the nature of the obstacles influencing dislocation movement. Since there have been numerous articles which have reviewed the mechanisms proposed to explain various aspects of plastic flow of bcc metals (for example, conrad1 and Keh and weissmann2), no attempt will be made here to discuss their conclusions. However, it should be to the surface stress while the term Kfd is the stress required to move dislocations through internal obstacles. Further, it was possible to derive the well-known empirical equation C = , and it is shown that the terprz a is comprised of two terms: a term Cs associated with the surface layer stress and Ci related to internal dislocation obstacles. pointed out that in all of these publications it has been tacitly assumed that plastic flow occurred uniformly throughout the cross section of the specimen (except, of course, for the Luders band region), It has generally been further assumed that the nature and distribution of the obstacles opposing the motion of dislocations are of the same type throughout. The role of the surface layer in bcc metals has not, as yet, been considered even though its role in fcc metals has been shown clearly to be of primary importance.3-5 Investigations on fcc metals have shown that at the onset of plastic deformation a surface layer acts to

Jan 1, 1968

By AIME AIME

T HE appointment of Herbert Hoover to the portfolio of Commerce in the President's Cabinet is to engineers the fulfillment of a long deferred hope to have an engineer in high political office and is a matter of congratulation to us for three reasons; because he is a mining engineer who represents the highest type of idealistic engineering effort; because he is a past president of the Institute; and because he has probably a broader grasp of world problems than any other living engineer. Frank A. Vanderlip in the preface to his book "What Happened to Europe" tells of the many interviews he had with the most prominent men in Europe which were made possible for him by his eminence as a banker and by the courtesy of the American ambassadors. He cites by name such well known figures as Austin Chamberlain, Sir Auckland Geddes, Monsieur Delacroix, Monsieur Briand, Mr. Padkrewski, Mr. Venizelos, Colonel House, General Pershing, Mr. Baruch, and many others and says :

Jan 1, 1921