Search Documents

By Arthur West

IT is the purpose of this paper to describe briefly some recent large power stations for blast furnaces, where the blast is exclusively supplied by gas engines using furnace gas. The stations are given in the chronological order in which they were designed, in order to indicate the various improvements suggested by experience. Fig. 1 shows the blowing-engine station of the Bethlehem Steel Co. at Bethlehem. Although the picture shows only five blowing engines, the house now contains 11 engines. In the diagrammatic. plan the arrow shows the position and direction of camera. This station handles five modern blast furnaces of 450 to 500 tons capacity each. In this, as in all the other stations described in this paper, each furnace is blown by-two single tandem gas engines. Ten engines are thus required for five furnaces, leaving one single tandem spare engine. This spare capacity has been shown by several years' experience at Bethlehem to be adequate to insure continuous operation. The engines in the Bethlehem station are right hand and left hand, arranged in pairs. The outboard bearings of each pair are close together so that there is not room for passageway between them. On the right of the picture are shown the inclined drums communicating with the cold-blast lines outside of building, so that any engine may be operated on any furnace. The illustration shows four cold-blast gate valves with pipes passing through wall, but since the photograph was taken the drums have been extended to take care of a fifth valve for a fifth furnace. At the extreme back of the picture can be seen the tubs of three twin vertical-horizontal Southwark steam blowing engines, which, although of modern design and as good as new, are not operated because of the greatly reduced blowing cost shown by the gas blowing engines.

Jan 6, 1915

By W. W. Gorr, R. Smith, E. H. Wyche

THE combination of high strength and corrosion resistance of cold-worked 18 Cr, 8 Ni steel has been advantageously utilized for some time, particularly in aircraft and rail car structures. There are, however, certain limitations on the use of such materials because the high strengths can be obtained only by cold-working, limiting the available products to sheets, strip, wire and tubes. The authors sought to overcome these limitations by resorting to precipitation-hardening, which has been used so successfully in nonferrous metallurgy but only to a limited extent in iron-base alloys. Accomplishment of this objective not only overcame the limitations, but also effected certain improvements in mechanical and other properties. This paper is an account of the development by Carnegie-Illinois Steel Corporation of a precipitation-hardening 18-8 stainless steel (called Stainless W? and tentatively identified as type 322). A description is given of its composition and metallurgical characteristics, heat-treatment, physical and mechanical properties and corrosion resistance. DEVELOPMENT OF THE NEW STEEL For a considerable length of time the authors were unable to determine the mechanism of the precipitation-hardening process that had been noted by Ffield 18,19 in 18-8 Ti or 18-8 Cb after cold-working and reheating to moderately elevated temperatures. All known variables were exhaustively studied, but with little success. However, results began to indicate that chemical composition was the most important variable, particularly the ratio of austenite-forming to ferrite-forming elements. The investigators 'then focused their attention upon the composition, and, in particular, upon the element titanium and its mode of alloying in the presence of other elements. A heat was obtained that could not be brought to the softness level of annealed 18-8. The response to cold-straining and aging* was very marked by previous standards, and, more important, cold-straining was found to be entirely unnecessary to produce the precipitation-hardening effect. The chemical composition of this heat was: C, 0.06 per cent; Mn, 0.54; P, 0.016; S, 0.016; Si, o.58; Ni, 7.28; Cr, 17.6o; Ti, 0.90; Al, 0.17. For some time the development work, particularly on composition, was carried

Jan 1, 1946

By J. E. Berry

AII evaluation is made of the acoustic velocity log for measurement of formation porosity. Plots of field-observer1 velocities vs core-measured porosities of sandstones and limestotnes with inter intergranular porosity show that the velocity log gives a useful measure of porotity, in agreement with published data. A new method of plotting electrical and velocity log data makes it easier to recognize hydrocarbon-water coritnct~ from log darn and to make serni-quantitative estinlates of hydrocarbon saturation. Two examples of this interpretation technique are given. This paper also discusses the various factors that affect acoustic velocity and shows how corrections can be made for some of these factors. INTRODUCTION Although the continuous velocity log was developed primarily as an aid to seismic interpretation, it is finding widespread use for measurement of porosity. The purpose of this paper is to evaluate this use of the log. Results are presented for the velocity-porosity relationship in many sandstones and one limestone. Practical applications of porosity values derived from the velocity log to improve interpretation of electrical surveys are presented. Various parameters which affect velocity in porous media are considered. Porosity, composition, cementa-tion, pressure difference (overburden pressure minus fluid pressure), fluid saturation, and wellability are discussed. Some of the ideas are opinions based on general considerations of well logging problems while others are supported by published data and our own observations. Major conclusions from these studies arc given in the body of the paper and detailed discussions of some of the various factors affecting porosity are given in the Appendix. POROSITY Sandstones The primary factor affecting the velocity of sound in porous media is porosity. Wyllie, et al,1 have reported a time average equation for the relationship between velocity and porosity.* This has found considerable acceptance in the industry. Other relationships between velocity and porosity have been proposed, none of which are entirely satisfactory. It is doubtful that any one relationship will completely describe all situations. We have tried an empirical relationship based on correlating log velocities with core-measured porosities. Measured porosities were averaged over a depth interval equal to the spacing used in recording the velocity logs. The depth range for the information used was from 2,000 to 12,000 ft. Velocity measurements were normalized for the effects of depth and overburden pressure. A detailed discussion of the basis for this normalization is given in the Appendix. The change is usually insignificant and when working with individual formations it can be neglected. All velocity measurements were normalized to a depth of 10,000 ft. The velocity-porosity data for sandstones in Fig. 1 came from 20 wells scattered throughout the Mid-Continent and Gulf Coast areas. The scatter of the data points is attributed to three causes: 1. There is no theoretical basis for expecting an exact velocity vs porosity relationship and it is not possible to correct precisely for the effects of such factors as impurities, grain shape, manner of cementation, etc. Some of these factors are discussed in the Appendix. 2. Porosities measured by core analysis are not necessarily representative of what the velocity log "sees". 3. Inaccuracies appear in the velocity log reading. This is particularly true of velocities from one-receiver logging tools.*" A linear-time curve (time-average equation) is plotted in Fig. 1 along with the best straight line through the points. Velocities used for the linear-time curves were 19,500 ft/sec for the matrix velocity (zero porosity) and 5,500 ft/sec for fluid velocity. For clean sandstones with velocities greater than 10,000 ft/sec, there is little difference between the velocity-porosity and the time-porosity curves. Both curves are well within the scatter of data points. The data points in Fig. 1 were restricted primarily to clean sandstones, using the SP and/or gamma-ray logs as clues to the lithology. Where a lithologic de-

By John D. Wiebmer

There are those in the Colstrip, Mont., area who can still remember the opening of the Rosebud mine in 1923. For 35 years it was a steady employer of 80 or 90 residents who produced coal for the railroad. In 1958, though, mining ceased as diesel locomotives supplanted steam engines. The mine was purchased in 1959 by Montana Power, the parent of Western Energy Co., and production resumed in 1968. Long Construction Co. was chosen as operator of the mine equipment. At that time, reserves appeared virtually unlimited. The thick Rosebud seam coursed through alternate sections of railroad holdings and federal land-then came the federal moratorium on coal leasing in 1971. About the time Western Energy completed the special leasing procedure to extend reserves from an existing mine, a new federal monkey wrench was thrown into the works with passage of the Surface Mining Control and Reclamation Act of 1977.

Jan 12, 1979

By Hans Allenius, R. T. Hukki

This paper describes in quantitative terms the effect of sharpness of classification on the performance of the closed grinding circuit. The analysis is based on a large number of laboratory experiments designed to simulate the two most common industrial closed grinding systems. The experimental results show quantitatively the degree of improvement achievable by more efficient classification. In an earlier paper1 the senior author has presented a trend showing qualitative analysis of mill and classifier performance in tile closed grinding circuit. According to this analysis, the master key to a major improvement appeared to be effective removal of finished fine material from the classifier sands, or in other words, improved sharpness of classification, leading simultaneously to a substantial reduction of the circulating load. One purpose of this paper is to present the results of a quantitative investigation of the closed grinding circuit. Another is to set forth the essential pertinent variables revealed by the quantitative experiments carried out by the junior author. In the two most common systems of closed-circuit grinding, (1) feed to the circuit is introduced into the grinding unit, normally the ball mill, operating in closed circuit with the classifier; or (2) feed to the grinding circuit is introduced into the primary grinding unit, normally the rod mill, discharging into the classifier in closed circuit with the secondary grinding unit, normally the ball mill. In the following discussion, these two systems are analyzed separately in the indicated order. BALL MILL - CLASSIFIER CIRCUIT The Test Apparatus and Procedure: The test appara- tus included: (1) a F 195 mm x 220 mm laboratory ball mill rotated at a speed 77% of the theoretical critical speed, and a 7-kg batch of F 20 mm-F 50 mm steel balls; (2) a conventional 65-mesh test sieve and a Ro-Tap sieve shaker serving as a classifier; and (3) a Permaran instrument manufactured by Outo-kumpu Co. for surface area determinations by the permeability method. As no continuous closed-circuit experiments could be brought about on a laboratory scale, the process was broken down into alternating grinding and sizing steps in such a way that the new feed plus the returning sands always formed a batch of 1000 gm. For each selected grinding period and for each selected sharpness of classification the basic steps were repeated six times. Steady-state conditions were then reached. Crystalline vein quartz was used as a test material. Feed to the process consisted of -10-mesh fraction of this quartz crushed in rolls. This fraction included 15% of-65-mesh material. Experimental Results: The general flowsheet is shown in Fig. 1. Table I gives the essential data obtained representing steady-state conditions under the indicated set of variables. The table is based on 110 grinding experiments, 440 screen analyses and an equal number of specific surface area determinations. Fig. 2 shows the relationship between the cumulative net energy consumption and the cumulative number of mill rotations as evaluated by separate experiments. Note that this relationship is not linear but is instead represented by a slight curve. The data given in Table I are presented in graphical form as follows: Fig. 3 shows the produced -65-mesh material in grams per minute vs. time of grinding in minutes; the sharpnesses of classification at 65 mesh were 100%, 75% and 50%. It is clearly indicated that the highest-capacity figures call for relatively short grinding times and for the sharpest possible classification. Fig. 4 presents the specific surface area on the final -65-mesh product in square centimeters per gm vs. time of grinding in minutes. In conventional mineral dressing processes, a final product characterized

Jan 1, 1969

By H. R. Barnhurst

It would be a difficult matter to trace from the beginning the very few improvements made in the burning of fuels prior to 1860. Donbtless the crossing of the sticks of wood in building a mood fire early appealed to our savage ancestry as a means of expediting its effectiveness for their crude culinary purposes. Stones and andirons came later in assisting the admission of air to the under part of the fuel bed, while beacons and cressets, utilized metal bars as supports for the same purpose. It is probable that Tuba1 Cain owed his success to the use of bellows making possible the use of mixed fuel and charge upon a hearth. With the development of working in cast iron, grate bars came in, and they are still with us doing duty in every household and almost every art where heat is a factor. Little was done beyond these crude methods prior to 1860. With the advancement of knowledge came the fuel-gas producer, a natural child of the retorts employed in supplying illuminating gas. It is only within the last 15 years that the conclusion became general that complicated systems for saving heat would not remedy deli-. ciencies in its primary development, and within that time there has been great advancement in the means of producing initially a fire of high effciency, so that to-day we are moving rapidly toward both high development and high absorption, with the resultant of high efficiencies. In studying the subject of the availability of pulverized coal as a fuel, it may occur to ask, why has this not come up earlier? This, question would be naturally prompted by recalling the fact that Thomas Crompton's English patents upon his methods were issued to him nearly 40 years ago. A conclusive answer to this, however, is that Crompton at that time had very crude facilities for making what was at best a very imperfect pulverization of the coal, arid the expense of preparation mas very great. He does not seem to have been aware of the advantage of a thorough drying of the coal in the

Jan 1, 1914

ONE of the features of the annual meeting was a round table conference on carbon in pig iron, on Feb. 16. This was presided over by R. H. Sweetser, and the discussion, which was so interesting as to require holding an additional session in the after-noon, ranged over such a wide field that only a brief outline of it will be attempted here. The full discus-sion together with the papers will be printed later. The first paper was one on the need for research in foundry pig iron (1648-C) by Richard Moldenke, who pointed out the trend in present practice of attaining low cost in pig iron production by hotter blast, addi-tion of. scrap to the blast furnace, and. the enormous increase in the output per furnace day. He pointed out that remelting processes are oxidizing processes, to some degree at least, and the metal cannot be given the deoxidizing finish which is characteristic of the steel-making process. The trend today is toward specifying total carbon content in foundry pig irons, and since the carbon content depends on a variety of factors, he suggested that the blast-furnace men and the foundry men study the question and agree on a minimum of total carbon for the given silicon ranges. The discussion of this paper was participated in by E. J. Lowry, Robert Jones, T. L. Joseph,. R. H. Sweet-ser, J. G. Ferguson, W. B. Coleman, E. P. Ross and D. J. Demorest and ranged from a comparison of the total carbon used in making a ton of pig iron in charcoal practice versus coke practice to a discussion of the bad effects observable from the use of scrap This paper was followed by one on carbon character-istics of copper-bearing pig iron by W.. B. Coleman. In view of the belief in many foundries that copper-bear-ing pig iron made trouble in the foundry, experiments were made by adding copper in various amounts up to 1 per cent and with the cooperation of the Robesonia Iron Co. a large number of tests were made over a run of foundry iron. The final conclusion was that the ad-dition of less than 1 per cent metallic copper did not seem to alter the physical properties and that a blast furnace using copper-bearing ore can produce pig iron suitable for making small castings, showing low-Brinell hardness test, good transverse and deflection tests, and high-total carbon.

Jan 3, 1927

By R. E. Zinkham, R. J. Goodwin

A mathematical study has been made of the amount of support a cement sheath could provide to casing cemented into the earth. Several assumptions were required to make the analysis, but only two of them are limiting: (I) the pipe must be completely surrounded with cement, and (2) any mud filter cake between the cement and formation has the same physical properties as either the cement or formation. The calculations showed that little support would be provided to the pipe before an unsupported cement sheath failed in tension; however, when the cement is confined between the pipe and wellbore and is loaded in compression, the pipe could receive a considerable amount of support. In fact, the theoretical results indicate the lower grades and larger sizes of pipe could have their working pressures doubled when reasonable compressive loads were applied to a surrounding cement sheath. These data are shown in six charts. Other down-hole conditions such as setting the cement under pressure, increased temperature and cement confinement all tend to increase the potential usefulness of the sheath. Because of size limitations, a laboratory program to verify the most important results of this mathematical study would be very difficult. However, small-scale field tests would be practicable. This paper shows that, if a solid cement sheath can be obtained in the field by either primary cementing or by repair after detection of flaws by surveys such as the new cement-bond logs, the use of this approach to reducing pipe costs merits further consideration. INTRODUCTION A modification in casing design practices is proposed which may either reduce the amount and grade of steel required to contain a specified internal pressure or permit the working pressure to be increased for a specified weight and grade of pipe. One of the more important considerations in casing design is its resistance to collapse; however, Bowers' and, more recently, O'Brien and Goins' have shown many casing programs are unnecessarily conservative in this respect, and they have indicated how savings can be made by designing for more realistic down-hole conditions. Earlier, Saye and Richardson howed that pipe costs could be reduced by considering the cement sheath as a part of the casing string when collapse resistance was being calculated. More recently, Rogers4 has raised the question as to whether a cement sheath might be considered in the design for burst resistance of the cemented casing. Calculations have been made for the increased burst resistance a cement sheath would provide for casing in a wellbore, and the results show that a sizable amount of support could be obtained in some instances. These data are presented in addition to a discussion of several other factors that are considered to affect the burst strength of pipe supported by cement. Two types of support are treated: Case I for tensile loading of the unconfined cement sheath, and Case for compressive loading of the confined cement sheath. ANALYTICAL TREATMENT AND RESULTS CASE I—TENSILE STRESSES IN AN UNCONFINED CEMENT SHEATH Conditions like this would most likely occur in a greatly enlarged portion of the hole where the cement was not in immediate contact with either the formation or a thin and hard mud cake. The mathematical analysis for this condition, as shown in the Appendix, rests on the following concepts. Pressure inside a unit length of pipe causes: (1) a tensile or tangential stress to be exerted over the longitudinal cross-sectional areas of the pipe and cement; and (2) an equal amount of strain in both the pipe and cement that is uniformly distributed over the wall thickness of each. This analysis was then used to make several calculations for a cement sheath around 51/2-in. OD pipe. The results are illustrated in Fig. 1, which shows that a tensile stress of 500 psi is imposed on a 5-in. thick sheath when the casing contains a pressure of only 1,450 psi. It also shows that a 10-in. thick sheath would be stressed to 500 psi in tension when the pipe contained a pressure of only 2,350 psi. Alternatively, if the stress analysis is made by means of the Lame thick-wall cylinder theory, the inner fibers of the 10-in. thick sheath will be stressed to 500 psi in tension when the pressure in the pipe is only 990 psi. This, of course, reveals that an unconfined sheath is of little support to the pipe in burst; however, an entirely different result is obtained when the cement is confined between the pipe and formation.

By F. A. Forward, J. Halpern

A new process is described for extracting uranium from ores containing sulphidic minerals, which comprises treating an aqueous pulp of the ore with air or oxygen at elevated temperatures and pressures. The acid required to dissolve the uranium is generated during the leach through oxidation of the sulphides. The chemistry of the process is discussed and laboratory results are presented to illustrate the operation of the method and the variables which control it. With most ores, leaching at a temperature of 130°C and an oxygen partial pressure of 10 psi provides uranium extractions of 90 to 95 pct in 4 to 6 hr. The acidity and level of dissolved impurities in the leach liquor can be kept fairly low. The method is characterized by a number of advantageous features including low reagent cost, short retention times, and high recoveries. RECENTLY there have been developed several processes for extracting metal values from ores by pressure leaching techniques;' -' an example is the carbonate leaching process for uranium ores which has been studied in this laboratory.' Leaching is carried out under oxygen pressure to ensure oxidation of the uranium to hexavalent compounds which are soluble in carbonate solutions. During the course of investigations relating to this process, it was observed that sulphide minerals, such as pyrite, usually were oxidized under the conditions of the leach treatment resulting in the formation of iron hydroxides and sodium sulphate, i.e. 2 FeS= + 7Vz O2 + 8 Na,CO3 + 7 H,,O -* 2 Fe(OH)3 + 4 Na2SO4 + 8 NaHCO.,. [1]

Jan 1, 1956

By Y. Mishima, R. Shiromizu

THE equilibrium y phase in Cu-Be alloys forms by discontinuous precipitation, the new phase nucleating at the grain boundaries and growing into grains on both sides of the boundary. When the alloy is aged above 500°C, however, growth may take place into only one of the grains.1'2 In A1-Ag alloys it is known that the precipitate has the same orientation as the grain in which no growth takes place.3, 4 This was confirmed in the present investigation on a Cu-Be alloy. A Cu-1.79 wt pct Be alloy was solution-treated at 810°C for 2+ hr, quenched into water at O°C, and aged at 600°C for 1 hr in a salt bath. The specimen was thinned by chemical polishing and electropolishing at room temperature in a solution of H3PO4 saturated with CrOs. The foil produced was examined in a JEM 150 electron microscope operating at 150 kv. Fig. 1 shows precipitates growing on only one side of the grain boundary. The black platelike precipitates were identified as the y phase. Electron dif-

Jan 1, 1969

By L. C. Brown, J. S. Kirkaldy

AS part of a program to investigate the diffusive properties of dilute ternary austenites, we have made a determination of the effects of cobalt on the activity of carbon in y iron. Samples of pure iron and Fe-Co alloys were equilibrated at 1000°C in controlled CO-C02 atmospheres, following the procedure of R. P. smith.' The 0.010-in.-thick samples were analyzed for carbon by microcombustion analysis2 to give a set of isoactivity curves. The latter were converted to activity-coefficient (standard state at infinite dilution) plots by combination with Smith's data' for the activity of carbon in pure iron measured in a CO-C02 mixture. Table I shows the composition of the base alloys used, while Fig. 1 shows the experimental results superimposed on a set of curves generated by the relation In the notation of Wagner,' the interaction parameter is the second coefficient on the right, Eq. [I] adequately correlates the experimental points for those alloys which were prepared from electrolytic iron by arc-melting (2,4, and 7 pct Co). The results for the 10 pct Co alloy (supplied by Crucible Steel Co.) do not correlate with the others. In fact, the experimental points for this alloy correspond to an interaction parameter of It is possible that the interaction parameter is a function of concentration for large cobalt additions, but we are inclined to attribute the discrepancy to the presence of a significant amount of aluminum added to this alloy for deoxidation purposes (Table I). Preliminary measurements for the system Fe-C-A1 have indicated an interaction parameter of Which implies that the effect of aluminum in solution on the carbon activity is sixty times greater than the effect of an equal weight percentage of cobalt. These observations cast some doubt on the precision of the results of Chandhok, Hirth, and Dulis who used this same 10 pct alloy for their experiments, obtaining an interaction parameter of E = 2.2. There is considerable doubt as to the activity of a plane Fe-C system. Using a CH4-Ha mixture, Smith obtains cg = 6.1 for the effect of carbon on the activity of carbon in austenite, rather than the value of 8.9 given in Eq. [I]. The use of CHa-Ha mixtures has recently been questioned by Kaufman, Radcliff, and cohens who state that there is some possibility that other hydrocarbons are formed. Fortunately, the determination of the interaction parameter is not sensitive to the coefficient of Nc. For example, using the CHI-H2 results we obtain a value which is almost the same as that obtained using the CO-CO, results. The authors wish to thank Mr. E. J. Dulis of the Crucible Steel Co. of America for supplying us with samples of the 10 pct Co alloy used in their original work. Financial assistance from the American Iron and Steel Institute is gratefully acknowledged.

Jan 1, 1963

By W. O. Philbrook, R. H. Spitzer, F. S. Manning

A generalized mathematical model has been developed to describe the kinetics of gas-solid reactions with special attention given to the hydrogen reduction oj dense spheres of hematite. This reduction process must pvoceed through a sequence of transport and chemical .reaction steps acting in series. Under typical experimental conditions, none oj the individual transport and reaction resistances may be neglected in the development of a physically significant model. A linear vate of thickening oj the product layer, usually taken as evidence of interface-controlled .reuction, may be observed even though transport resistances play a dominant role in the over-all kinetics. The temperature and pressure dependencies of all terms have been carefully evaluated in order to .make fill use oj arailable expe-inzental data in evaluation oj the model. FOR obvious technological reasons, the kinetics of reduction of iron oxides has become the subject of intensive experimental and theoretical investigation during recent years. Continuing efforts to construct mathematical models to describe the kinetics of reaction between a gas stream and a granular bed of solid particles have demonstrated the necessity of a thorough understanding of the reaction kinetics of a single particle within the system as a prerequisite to the construction of physically significant models of complex, reacting systems. This paper presents a critical examination of the transport and chemical-reaction processes involved in single-particle oxide reduction and develops the mathematical expressions necessary to evaluate their importance. Comparison of theoretical predictions with experimental results contributes important new understanding of the complex nature of this process. The reduction process has been studied under a wide range of experimental variables, and it is not surprising that apparent conflicts in observation and interpretation appear in the literature. The interested reader is referred to the reviews of Themelis and auvin"? and Manning and philbrook3 for a description of much of this work. The course of reaction commonly has been followed by measuring the oxygen weight loss from the particle as a function of time. A number of authors have suc- cessfully correlated their data in terms of a model which assumes that the reduction process is controlled by the rate of reaction at a single, sharply defined, advancing interface. According to this model, the interface will advance linearly with time. A mathematical model for gaseous reduction in a packed bed developed by the present authors in an earlier paper4 recognized that reduction must proceed through the series hematite (Fe203), magnetite (Fe30,), wiistite (Fe,O), and finally metallic iron. The reduction scheme permitted a stepwise topochemical reduction of the individual particles to metal or to the lowest oxide thermodynamically possible for the local gas composition in the bed. The limiting situations of theoretically dense and very porous oxide structures were considered. On the basis of available experimental evidence, the simplifying assumption was made in each case that all product layers would thicken linearly with time. A generalized single-particle model has now been developed to determine the significance of transport resistances in the product layers and in the gas film surrounding the particle. The analysis shows that the interplay of transport and chemical resistances is such that an apparently linearly advancing interface may be observed despite the fact that the reaction may be under significant transport control. Attention thus far has been focused on the development of a model for the topochemical behavior of dense spheres of hematite in atmospheres capable of reducing them completely to metal. The formation of successive product layers of iron, Fe,O, and Fe304 is assumed to follow the mechanism originally described by dstrijm.' All oxygen removal from the core occurs at the iron/Fe,O interface, intermediate oxide layers being propagated by sol id-state diffusion without change in the oxygen density of the core. Since fractional reduction is operationally defined in terms of oxygen weight loss, the kinetics of the over-all reduction of FeZ03 to iron is properly studied in terms of the gas-solid reaction occurring at the iron-wiistite interface. The fractional reduction of a partially reduced oxide sphere is given by: here refers to the radial position of the iron/Fe,O interface. This model is not universally applicable because, as explained in the earlier paper,4 a consideration of porous particles or of dense particles in atmospheres not capable of reducing wiistite must allow for the possibility of gaseous reduction at interfaces other than the one between iron and Fe,O. However, evidence that certain hematite specimens actually do follow the dense-pellet mechanism developed here is provided by the data of cewan' and of Bogdandy and

Jan 1, 1967

By AIME AIME

Report of Committee 24, of the International Association for Testing Materials, presented at the Brussels Congress, 1906. Republished for use at the 94th Meeting of the American Institute of Mining Engineers, New York, N. Y., February, 1908. Discussion by letter is requested by the Secretary of the Institute. The Committee appointed for the solution of Problem 24 consisted of the following members Prof. H. M. Howe, New York, N. Y. (Chairman); L. Levy, Paris, France (Vice-Chairman) ; Prof. D. Tschernoff, St. Petersburg, Russia (Vice-Chairman) ; Prof. Albert Sauveur, Cambridge, Mass. (Secretary) ; Van Drunen, Ixelles, Belgium; Lieut.-Col. H. Tusen, Copenhagen, Denmark ; E. P. Martin, Abergavenny, England ; A. Pourcel, Paris, France ; H. Brauer, Dortmund, Germany ; Dr. Prof. H. Wedding, Berlin, Germany; P. Verole, Milan, Italy ; A. Baalsrud, Christiania, Norway ; A. R. v. Dormus, Vienna, Austria ; A. Sailler, Vienna, Austria; Bureau des Forges, St. Petersburg, Russia; Prof. N. Belelub-sky, St. Petersburg, Russia ; N. Jossa, St. Petersburg, Russia ; Maj.-Gen. M. Korobkoff, St. Petersburg, Russia ; S. Smirnoff, St. Petersburg, Russia ;.Ladislaus v. Tetmajer, Budapest, Hungary ; H. H. Campbell, Steelton, Pa. Early in February, 1905, a list of species and varieties of iron and steel, with definitions, drawn by the Chairman and Secretary of Committee 24, was sent to every member of this Committee with a request for comments and suggestions. A special request was sent to the following gentlemen . for the equivalents in their several languages of these species and varieties : A. , Pourcel, Paris, France; Prof. H. Wedding, Berlin, Germany ; J. A. Brinell, Stockholm, Sweden ; Prof. H. I. Hannover, Copenhagen, Denmark; Prof. P. Kley, Delft, Holland; P. Verole, Milan, Italy; Col. Cubillo, Trubia, Spain. This present report, which is based upon our original list and definitions, and upon the replies to these requests, consists of four parts I. A polyglot, which gives the names of the chief classes of iron and steel in English, French, German, Swedish, Danish and Dutch. We .regret that we have failed to get the Italian and Spanish names. II. English definitions of principal classes of iron and steel. III. A glossary of special sizes and shapes of iron and steel. IV. A note on the boundary between steel and cast-iron. I. POLYGLOT, IN ENGLISH, FRENCH, GERMAN, SWEDISH, DANISH AND DUTCH, OF THE CHIEF CLASSES OF IRON AND STEEL, AND OF THE APPARATUS IN WHICH THEY ARE MADE. This list is not intended to be complete, but rather to include only those varieties which are of interest to the Association.

Mar 1, 1908

By R. H. Schnitzel

Internal-friction peaks have been observed in tungsten single crystals at about 300° and 400°C. The characteristics of these peaks are similar to interstitial peaks observed in other bee metals; therefore, the origin of these peaks appears to he the Snoek mechanism. The interstitial responsible for the peak at about 300°C has not been identified. Carburizing increases the magnitude of the peak at about 400°C; consequently, it appears reasonable to suppose that the specific interstitial associated with this peak is carbon. The activation energies associated with the 300° and 400°Cpeaks are about 35,000 and 45,000 cal per mole, respectively. INTERNAL - friction peaks resulting from the stress-induced diffusion of interstitials (Snoek relaxation peaks) have been frequently observed in bee metals.1-5 Attempts to detect Snoek relaxation peaks in tungsten have, however, not been fruitful.' Failure to find Snoek peaks in sintered tungsten can perhaps be attributed to one or more of the following difficulties: a) the relatively low purity of the sintered tungsten; b) the lack of extensive metallurgical knowledge about tungsten-interstitial alloys, such as suitable interstitial dosing and quenching procedures; and c) the inconsistency of some of the interstitial analyses of tungsten, which reflects itself in one's inability to be sure of the nature of the specimens. This present investigation did not overcome all of these difficulties for successful tungsten internal-friction measurements. Some of these difficulties still persist and new difficulties were encountered during the course of this investigation. Nevertheless, the use of electron-beam tungsten single crystals having somewhat greater purity levels than sintered tungsten combined with appropriate carburizing and quenching procedures permitted a reasonable attempt to be made. As a consequence, internal-friction peaks were observed in these tungsten single crystals at about 300° and 400°C. These peaks were found to be unstable, since they annealed rapidly away during a sequence of internal-friction measurements. Hence, it was necessary to construct an apparatus having a faster heating rate to study some of the details of these peaks. From the behavior of these peaks as well as our knowledge of similar peaks in other bee metals, one can reasonably conclude that these peaks are caused by residual interstitial impurities within these crystals. Further investigation of these peaks after the application of various metallurgical treatments lent credence to this supposition. EXPERIMENTAL TECHNIQUE The internal friction of tungsten single crystals was measured using two different pieces of apparatus both of which are of essentially the same conventional design, namely the KE type of torsion pendulum. The important difference between these two types of apparatus was in the attainable heating rate and method of protection of the specimen from atmospheric contamination. The apparatus designated "number 1" was enclosed in a vacuum chamber which was heated by an externally mounted furnace. It had a slow rate of heating which was estimated to be about 4°C per min from room temperature to about 350°C and then about 1°C per min to 600°C. The internal friction of tantalum was measured with this apparatus and the established Snoek peaks were found.' These tantalum peaks in the temperature range from room temperature to 400° C served as a check for the apparatus. The apparatus designated "number 2" having a faster heating rate than number 1 was not elaborate. It consisted of a mounted nickel tube to which split heating elements were attached. Argon was used as the protective atmosphere. The measured heating rate was about 12° to 15°C per min whereas the cooling rate was somewhat slower at about 10° C per min because of the increased difficulty encountered in stabilizing the temperature. No surface oxidation of the specimen was noted after any test. This apparatus was also checked with the known peaks of tantalum.1 The preparation of the single-crystal specimens for internal-friction measurements consisted of centerless grinding the crystals from an approximate 0.200 in. diameter to 0.030 to 0.040 in. in diameter, and then electropolishing them to about 0.020 in. in diameter. Single crystals processed in this manner are designated as being in the virgin condition. Since the length of crystal varied from 3 to 9 in., the test frequency varied from about 1 to 2 cps. The frequencies of measurement, axial orientations, and chemical analyses for the various crystals are listed in Table I. The controlled addition of carbon into tungsten is a difficult problem. Attempts to find the critical conditions necessary for an equilibrium treatment were not fruitful. Therefore, a simple nonequi-librium method was used. The addition of carbon to these crystals consisted of appropriately combining three treatments—carburizing to achieve a case, annealing to partially dissolve the carbon into the

Jan 1, 1965

By Robert C. Stephenson

In 1954, a year when general industrial production declined, it is significant that industrial mineral products continued in high demand. Phenomenal growth of the cement industry, increase in filler-fibre markets such as for asbestos and diatomite, expansion of the gypsum industry, and the increasing production of agricultural raw materials all illustrate the vitality of industrial minerals fields. Pioneer development of new industrial raw materials-wollastonite as a current example-requires keen foresight, hard work, and tremendous intestinal fortitude. The present-day requirements of industry for rigid quality control and uniformity of raw materials have resulted in highly specialized

Jan 3, 1955

By R. Simon

The sources of energy dissipation for concentrated loadings on rock are considered in an attempt to account for the experimentally measured magnitude of the work required to break out a unit volume of rock from the free surface of an essentially semi-infinite medium. It is concluded that most of this work probably represents the elastic strain energy developed by the loading in a much larger volume of rock beneath the loaded region than the volume of the rock fragment broken out to the side of the loaded region. This strain energy is largely dissipated in the form of stress waves generated by the high rate of unloading produced by the propagating cracks. The energies associated with the formation of the new surfaces of the cracks and with the stress waves generated directly by the loading process are computed to be negligibly small. Possibilities for improving the utilization of energy to drill rod. subject to the geometrical limitations imposed by down-hole operation, are discussed. It is pointed out that any such possible improvements would probably have to be differential ones, since each rock configuration of more favorabIe loading geometry that can be created down the hole is accompanied by a complementary configuration of less favorable loading geometry. INTRODUCTION Dislodging each cubic inch of rock from the bottom of the hole by the action of a bit requires the expenditure of an amount of energy that varies from approximately 5,000 in.-lb to approximately 100,000 in.-lb, depending on the hardness of the rock, or, more technically, upon its fragmentation strength.1 In this paper we will discuss (I) why the energy expended in drilling is so large, (2) what happens to this energy upon completion of the drilling process, and (3) what are the possibilities for reducing the magnitude of the energy required to drill rock. DETERMINATION OF ROCK DRILLING ENERGY The volume of rock removed per unit time from the bottom of a hole of diameter D is evidently (7/4)D2R, where R is the rate of penetration of the bit. If P is the rate at which work is done by the bit on the rock at the bottom of the hole, the energy required to break out a unit volume of rock is given by: Ev =(4/p) P/D2R............(i) For rotary drilling, of either the rolling-cone or drag-bit varicty, P = 2pLN, where L is the torque resistance to rotation at the bottom of the hole and N is the rate of rotation of the bit. L is essentially the same as the torque measured at the rotary table only when drilling in shallow holes. The energies expended in rotating the drill string against the frictional resistance of the walls of the hole and and against the viscous drag of the drilling fluid are extraneous to the subject under consideration, although these may be much greater in magnitude than E, when drilling in a deep hole. For percussion drilling, P = fE where f is the percussion frequency and E is the work done on the rock per impact. The latter quantity can be both computed and measured for a percussion drilling machine. 2 (Under satisfactory drilling conditions, defined in terms of ranges of numerical values of certain dimensionless parameters, E is only 30 to 50 per cent less than the impact energy of the striker.2) Alternatively, E, may be measured directly by dropping chisels shaped like bit edges, backed by rigid weights, onto the surfaces of laboratory rock samples of effectively semi-infinite extent. Under these circumstances, essentially all of the impact energy is converted to work done on the rock, and the relationships among volume of rock broken out, chisel shape, impact energy and indexing distances can be obtained.3 The values of the energy required to break out a unit volume of rock under favorable circumstances are substantially in agreement for rotary drilling, percussion drilling and drop testing at atmospheric pressure. The energy per unit volume is a quantity of the order of magnitude of roughly twice the com-pressive strength of the rock as measured by a uniaxial loading test. The phrase "order of magnitude" in this paper means from about 1/3 as much to 3 times as much; i.e., the energy per unit volume may range from roughly the same up to several times

Edmund Gybbon SpilsbURy, mining and metallurgical engineer of international reputation, died suddenly of heart failure on May 28, 1920, in the New York Eye and Ear Infirmary, following an operation for cataract, which had been successfully performed a few days before. Mr. Spilsbury was one of the early members of the American Institute of Mining Engineers, which he joined in 1873. During all this time he contributed freely of his time and ability. He was manager of the Institute from 1885 to 1887, vice-president, 1893 and 1894, and president in 1896. He was also a member of the Engineers Club, of which he was president in 1916 and 1917, American Society of Civil Engineers, American Society of Mechanical Engineers, Institution of Mining and Metallurgy, Mining and Metallurgical Society of America, American Electrochemical Society and the Rocky Mountain Club of New York. He was a trustee of the United Engineering Society from 1916 to his death; a member of United Engineering Society Library Board from its organization in 1913 until his death, being its chairman from 1918 to January, 1920; a trustee of Engineering Foundation Board from 1916 until his death; and member of the John Fritz Medal Board of Award. He was also a member of the Division of Engineering of the National Research Council. Born in London, England, in 1845, Mr. Spilsbury went to Liege, Belgium, at an early age, where he received his preliminary education. For his technical education he attended the University of Louvain, Belgium, graduating in 1862, and later he took a practical course at Clausthal, Germany. In 1864 he became assistant engineer for the Eschweiler Zinc Co., of Stolberg, one of the largest miners and smelters of lead and zinc in the world at that time, and the next year he took charge of that company's mines and works on the Island of Sardinia. From Sardinia he went to the Atlas Mountains in Morocco. In 1867 he entered the service of McClean & Stilman, of London, and had charge of the construction of the iron gates for the Surrey Commercial Docks. In 1868 he was designing engineer with J. Casper Harkort, and had charge of most of the detail work of the Keulenberg Bridge in Holland, the Danube Bridge in Vienna, and the Rhine Bridge at Düsseldorf. In 1870 Mr. Spilsbury came to the United States to investigate the lead and zinc resources for the Austro-Belgian Metallurgical Co. After spending two years in this work, he resigned in order to practice in the United States, and he was the first to introduce the Harz system of ore

Jan 1, 1922

Edmund Gybbon SpilsbURy, mining and metallurgical engineer of international reputation, died suddenly of heart failure on May 28, 1920, in the New York Eye and Ear Infirmary, following an operation for cataract, which had been successfully performed a few days before. Mr. Spilsbury was one of the early members of the American Institute of Mining Engineers, which he joined in 1873. During all this time he contributed freely of his time and ability. He was manager of the Institute from 1885 to 1887, vice-president, 1893 and 1894, and president in 1896. He was also a member of the Engineers Club, of which he was president in 1916 and 1917, American Society of Civil Engineers, American Society of Mechanical Engineers, Institution of Mining and Metallurgy, Mining and Metallurgical Society of America, American Electrochemical Society and the Rocky Mountain Club of New York. He was a trustee of the United Engineering Society from 1916 to his death; a member of United Engineering Society Library Board from its organization in 1913 until his death, being its chairman from 1918 to January, 1920; a trustee of Engineering Foundation Board from 1916 until his death; and member of the John Fritz Medal Board of Award. He was also a member of the Division of Engineering of the National Research Council. Born in London, England, in 1845, Mr. Spilsbury went to Liege, Belgium, at an early age, where he received his preliminary education. For his technical education he attended the University of Louvain, Belgium, graduating in 1862, and later he took a practical course at Clausthal, Germany. In 1864 he became assistant engineer for the Eschweiler Zinc Co., of Stolberg, one of the largest miners and smelters of lead and zinc in the world at that time, and the next year he took charge of that company's mines and works on the Island of Sardinia. From Sardinia he went to the Atlas Mountains in Morocco. In 1867 he entered the service of McClean & Stilman, of London, and had charge of the construction of the iron gates for the Surrey Commercial Docks. In 1868 he was designing engineer with J. Casper Harkort, and had charge of most of the detail work of the Keulenberg Bridge in Holland, the Danube Bridge in Vienna, and the Rhine Bridge at Düsseldorf. In 1870 Mr. Spilsbury came to the United States to investigate the lead and zinc resources for the Austro-Belgian Metallurgical Co. After spending two years in this work, he resigned in order to practice in the United States, and he was the first to introduce the Harz system of ore

Jan 1, 1922

By G. J. Wilson

Difficulties experienced in correlating vertical and lateral locations of subsurface features that are encountered in directional wells prompted critical review of the tangential method of computing directional surveys. Inherent discrepancies were indicated to cause small incremental but significantly large cumulative errors in computed vertical depth and horizontal departure. A radius of curvature method, developed for planning and analyzing directional wells, was studied as a means of more accurately calculating survey data. Errors incurred in the tangential method were not present in the radius of curvature method. Conflicting assumptions in calculating dog-leg severity by the tangential method were resolved by a new procedure that was derived from the radius of curvature method. Results of the investigation showed the radius of curvature method to be an improved method for computing directional surveys. Introduction Many improvements in directional drilling tools and techniques have been made in the past 10 years,' but the method of computing survey data has remained virtually unchanged. While use of computers greatly aids the process of calculation' and eliminates many human errors, manual and computer calculations are still made with the assumption that the wellbore consists of straight-line segments. This paper points out discrepancies in the method and presents an improved method in which the wellbore is assumed to be curved. Tangential Method The method presently used to calculate vertical depth, horizontal departure and direction coordinates with measured values of well depth, inclination angle and direction angle is termed the tangential method. This term stems from performing calculations with a series of straight-line segments, with each segment assumed to be tangent to the wellbore at a corresponding survey point. A segment is defined by inclination and direction angles measured at only the lower or deeper end. Consequently, a discrepancy or error is introduced for each segment. Errors are not of extreme magnitude, but cumulatively are significant due to the need to define as accurately as possible the vertical and lateral location of subsurface features such as pay tops, fluid contacts and fault cuts encountered in expensive directional well bores. In Fig. 1, the curved-line segment ab represents a portion of the actual borehole as viewed in the vertical plane. Points a and b are survey stations and +, is the inclination angle at point b. The curved-line segment ab is assumed to be the straight-line segment arb of a length equal to ab and tangent at point b to the curved-line segment. Lengths a'c' and c'b are equal to a'b cos +, and a'b sin +,, respectively. Point a already has been fixed by calcillations performed with survey data obtained at point a, and calculated lengths m'c' and c'b are projected as lengths from point a, rather than from point a'. Point b1 is thus fixed and assumed to represent the actual point b. Calculated length ac" is shorter than actual length ac, and calculated length c"bl is longer than actual length cb. Since b1 is the point from which the next deeper segment will be projected, errors are cumulative. Cumulative error continues to increase as long as the inclination angle continues to increase. When the inclination angle decreases (Fig. 2), calculated length ac" is longer than actual length ac, and calculated length c"bl is shorter than actual length cb. These errors also are cumulative, but differences between calculated and actual lengths are opposite in mathematical sign to differences demonstrated in

Jan 1, 1969

By Leroy Gardner

EVERY reader of this paper is well aware of the fact that the prolonged inhalation of large amounts of free silica dust results in fibrosis of the lungs, and that other inorganic dusts, except those of asbestos and the mineral poisons, are thought to be relatively harmless. But probably few have had opportunity to visualize the effects of silica, asbestos and other minerals upon living tissues. The ideal demonstration would be based upon sections of lungs from human beings that had inhaled com-parable concentrations of different dusts for a unit period of time. Such material is generally difficult to obtain and in some instances is of ques-tionable value because the subject has been exposed to more than one kind of dust. A demonstration could be prepared from the lungs of animals. However, so many months or even years are required to com-plete the exposure to each kind of dust that enough material has not been accumulated. For a general survey of the action of different types of dust, I am therefore compelled to use the tissues of animals that have been injected with suspensions of dust particles. The injection method offers certain advantages. The quantity, the particle size and the state of dispersion can be controlled with sufficient accuracy so that the tissue responses to different minerals can be accu-rately compared. The method insures contact between the tissues and the mineral particles; protective mechanisms, which may prevent the inhalation of certain types of foreign body, never come into play. If the pathway of injection be one that minimizes nonspecific injury, the tissue responses may simulate those produced by inhalation but they develop somewhat more rapidly. It should always be remembered that injection methods merely demonstrate the capacity of various kinds of minerals to provoke reaction in the tissues; whether the same substances are inhaled from atmospheric suspension and accumulate in the lungs in dangerous quantities can be demonstrated only by inhalation.

Jan 1, 1938