Search Documents

By D. Harker, M. J. Murphy

The mechanism by which age-hardening takes .place is still not completely understood. The principal theories range from the extreme of "precipitaiion-hardening" to that of "order-hardening," with many intermediate gradations. In the hope of obtaining new data on which to base a choice among the many theories, the authors have made electron micrographs of formvar replicas taken from metallic specimens at various stages of age-hardening. The results so obtained on an alloy of 2 per cent beryllium in copper and one of 20 per cent molybdenum in iron will be described in the following pages, as well as the technique used in preparing the replicas. Preparation of Formvae. Replicas of Metallic Specimens This section is concerned with the techniques that have roved successful in preparing formvar replicas for studying the microstructure of metals with the electron microscope. Because of its simplicity and accuracy, the formvar replica1 method developed in the General Electric Research Laboratory has been used exclusively, since it is much simpler than the silica replica method of Heidenreich and Peck2 and produces as good results. The formvar method to be described requires a technique acquired only by practice, and no foolproof set of rules can be given. it is a rapid method and a replica can be obtained in less than five minutes under favorable conditions. This does not mean that perfect replicas can be produced every five minutes, but rather that one can well afford to take several strippings* in order to produce a replica of high quality. The metallographic technique required for replica work—very fine polishing and etching with very dilute solutions—is described here. It can be said, in general, that almost any surface that has been carefully prepared for a photomicrograph at 1000 or more diameters can be used to obtain a replica for the electron microscope. Preparation of Metallographic Specimens The preparation of the metallographic specimens is somewhat more exacting than that usually given to samples to be used for inspection under the light microscope. After much experimentation, it was concluded that the best method consists in polishing the metal through to the coarse cloth, then etching and repolishing on final cloth until the layer of distorted metal is removed. After this procedure has been completed, a dilute etch—to approximately the depth necessary for a micrograph at 1000 diameters—usually produces a sur-

Jan 1, 1945

By AIME AIME

THE program of government drilling, conducted jointly by the U. S. Geological Survey and the Bureau of Mines, has demonstrated the presence in Texas and New Mexico of potash-bearing beds of considerable importance. Information regarding the ex- tent and location of the potash deposits as presented at the non-metallic sessions was of great interest to many engineers. These subjects will be covered in greater detail in later paragraphs. The first session, with about 50 in attendance, convened at 10 a.m. on Feb. 18, with Oliver Bowles, chair- man of the Committee on Non-Metallic Minerals, pre- siding. The first paper was on "Soapstone Mining In Virginia," presented by C. W. Ryan of Lynchburg, Va. The nature and extent of the soapstone deposits of Nelson County were described in some detail. In origin, the soapstone is undoubtedly related to a basic peridotite rock though its mode of formation is some- what uncertain. This main soapstone deposit occurs in three veins, the western, middle, and eastern, the middle vein being of greatest economic importance. Methods of stripping, quarrying and milling the rock were described and the uses of soapstone were enum- erated. In discussing this paper, C. P. Berkey, of Co- lumbia University strongly favored the theory of igneous origin of the soapstone and the need for further detailed geological study. J. L. Gillson of Cambridge, Mass., stated that the Vermont and New York talc deposits were always associated with characteristic minerals, such as, a chlorite of one particular variety, siderite, amphibole, magnetite, and biotite. C. H. Behre of Cincinnati, Ohio, raised the question of parallelism in the soapstone structure and Mr. Ryan stated that such parallelism was in evidence in some parts of the deposits. H. A. Wheeler of St. Louis, Mo., also took 'part in the discussion.

Jan 1, 1929

By S. F. Urban, G. Derge

AT the time this investigation was initiated variations were observed in the quality of different heats of basic electric-furnace steels, although they had been made under purportedly similar conditions. This indicated that these variations were related to normally unobserved variations in the character of the bath, especially during the "refining" period. Although the slags used for this operation are commonly referred to as "reducing" slags, and are regarded as having a "deoxidizing" action on the bath, no reliable measurements of this action were available. It was decided, therefore, to study the behavior of oxygen in the metal for a large enough number of heats to learn its normal variations and to relate these variations to regularly observed conditions [f] operation. The most important general conclusion reached was that the time a heat is held under a reducing slag should be reduced to a minimum, which was about an hour and a half under the conditions studied. Beyond this time no observable beneficial effects are obtained from the reducing slags, insofar as oxygen and sulphur content of the bath are concerned. It is likely that added time may increase hydrogen content as well as heat costs. The oxygen content of the bath is never reduced below the amount in equilibrium with the carbon. Concurrently with this work, J. S. Marsh1 presented data that supplement and support many of the results of this paper. PROCEDURE The work was done in two different electric-furnace shops of the same plant. The selection of heats was made primarily with regard to the convenience of heat schedules. Companion slag and metal samples were taken just prior to slag-off and throughout the refining period for an initial set of 17 heats, and before slag-off and near tap for an additional 13 heats. Slag sampling presented no particular problem; a spoonful of slag was poured onto a metal plate and when sufficiently cool was sealed in an airtight container. Sampling the metal for oxygen presented a more complex problem. Because of the lack of previous experience in sampling electric-furnace baths, a number of methods were compared. Chilled Wedge Samples2 An unkilled metal sample is removed from tie furnace in a well-slagged carbometer spoon and poured immediately into a heavy copper mold designed to provide rapid freezing. Three different types of molds were used to determine the optimum for electric-furnace heats. The Big Wedge Mold (a) was a 4 by 4 by 4-in. split copper mold, yielding a wedge-shaped casting 1 in. wide, 1 ½ in. long, and ¼ in. maximum thickness, and was finally adopted as the most satisfactory design. The Long Wedge Mold (b) was a 2 by 2 by 5 ¼ -in. split copper mold, yielding a wedge-shaped casting 1 in. wide, 2 ¾ in. long, and ¼ in. maximum thickness. The Small Wedge Mold (c) was 2 by 2 by 4-in. split copper mold, yielding a wedge-shaped casting 1 in. wide, 1 ½ in. long, and ¼ in. maximum thickness.

Jan 1, 1947

By Mark R. Lamb

THE treatment of slime is of special interest to those engaged in cyaniding gold- and silver-ores. The usual practice is to make as small a percentage of slime as possible. In many instances the slime is given no treatment, but is impounded in dams in the hope that the future will develop some method of economically treating this product. The filter-press was the first step upward from ordinary decantation, but, on account of heavy labor-charge and high cost, its use has been limited to high-grade material. The slime at the Combination mill at Goldfield averages perhaps $20 per ton, and although the values are quickly dissolved the filter-press installation was not entirely satisfactory, resulting in the erection of the canvas-cell filter, developed by Chas. Butters and his staff. This filter is a great improvement over the filter-press, and the following description of it will be of interest to those engaged in treating slime produced in crushing ores, especially in view of the fact that, by the use of this filter, slime can be treated at a lesser cost and with a higher percentage of gold- or silver-extraction than in the ordinary treatment of sand; and, moreover, the initial outlay for an all-sliming plant is less than that for the ordinary sand- and slime-plant. The economy of construction of the Butters filter-plant is clearly shown in Figs. 1 and 2, which illustrate the 20-frame filter of 40 tons capacity, now being installed by the Nevada Goldfield Reduction Co. In this construction the slime-pump is so connected that it can pump to or from either tank or the filter by changing the valve-settings-a combination which is necessary in this particular installation, since sufficient fall is not available for filling and discharging the filter by gravity. Ordinarily, a slime-plant comprises: a filter-box with frames

Jan 1, 1907

By D. Bergekoff

IN the routine examination of a wide variety of metal specimens it is sometimes necessary to have special methods of polishing in order to retain and reveal certain details in each specimen. Among such special cases is the retention of graphite in malleable and gray cast irons, the preservation of all types of nonmetallic inclusions in both hard and soft steels, obtaining a scratch-free surface with soft metals, and avoiding the usual relief effects with very hard specimens such as tool metals con-taining various carbide and nitride phases. It is the purpose of this paper to give an account of some of these special polishing methods in use at the Union Carbide and Carbon Research Laboratories. The polishing procedures outlined have been found to give uniform results. It is obvious that only general rules and the most important working details can be given here. Following these rules, the polisher can obtain satisfactory results if he possesses the necessary patience and has a sincere desire to give as nearly perfect a finish as possible to his work.

Jan 1, 1939

By Paul Giesecke

SINCE most modem metallurgical plants are operated continuously and on a large scale, successful operation at maximum efficiency demands that an accurate knowledge of the performance at each stage of the process be available at all times. Quantitative analyses provide the most practical process guides, and it is essential to have analytical procedures that combine accuracy and speed. In continuous plant operations, large losses may occur if the time interval between the development of trouble at any stage and its recognition and correction is great. Many metallurgical plants are using rapid colorimetric and spectrochemical methods of analyses for control purposes. So-called "color coppers" may be cited as an example of the colorimetric methods, in contrast with the routine use of the ultraviolet spectrograph for the analysis of steels.42 By means of this more refined spectrochemical procedure, a complete quantitative analysis of the molten metal is obtained every few minutes. During the past two years the Physics Division and the Ore Dressing Laboratory of the American Cyanamid Company's Stamford Research Laboratories have collaborated in a study of the use of spectrochemical methods for the analysis of various metallurgical products. New methods have been developed, which have proved of practical value in plant operation. The following pages give a general review of the principles of spectrochemical methods and also the details of several specific analyses. PRINCIPLES OF SPECTROCHEMICAL ANALYSIS In general, it can be said that a visible light spectrochemical analysis can be performed for any ion or molecule that is naturally colored, or that can be made to react with another to produce a colored salt or complex. Whereas transmission measurements in the ultraviolet and infrared portions of the spectrum are most useful for the analysis of organic molecules, visible light measurements are of particular value for metal salts. Such elements as copper, manganese, cobalt, nickel, iron, molybdenum, vanadium, chromium, phosphorus, mercury, zinc, lead, and a great many others, can now be determined with a high degree of sensitivity, accuracy and dispatch. From the simplest of qualitative determinations, color analyses have been improved to such an extent that, at the present time, through the use of recording spectrophotometers, hundreds of accurate quantitative analyses can be performed by a single analyst during an 8-hr. day after the standardization curves have been established for the ions to be determined.

Jan 1, 1944

By Stanley J. LeFond, Langtry E. Lynd

Elemental titanium has become famous as a space age metal, because of its high strength/ weight ratio and resistance to corrosion. However, the major use is in the form of titanium dioxide pigment, which because of its whiteness, high refractive index, and resulting light-scattering ability, is unequaled for whitening paints, paper, rubber, plastics, and other materials. A relatively minor use is in welding rod coatings, in the form of the mineral, rutile. United States consumption of titanium dioxide for these applications in 1973 was as follows: pigments, 891,000 st; titanium metal, 40,000 st (=24,000 st metal) ; and welding rod coatings, 10,000 st. The only commercially important titanium ore minerals at the present time are ilmenite, and its alteration products, and rutile. Titanium was discovered by Gregor in 1790, as a white oxide which he recovered from menaccanite, a variety of ilmenite occurring as a black sand near Falmouth, Cornwall. Barksdale (1966) states that the fundamental chemical reactions on which the present day titanium industry is based were known before 1800, although it was not until 1918 that these pigments were available commercially on the American market. Pings (1972) outlines the early history of the titanium industry in the United States, referring to the work of Guise (1964) and others: "Mining of titanium minerals in the United States began sometime between 1880 and 1900, in Chester County, Pennsylvania. Small quantities of rutile were also produced during the time in North Carolina and Georgia. In 1901 rutile was mined from a deposit near Roseland, Va., and was used in making titanium chemicals and for coloring ceramics. Ilmenite in the deposit was produced as a separate item in 1913, and rutile and ilmenite were obtained from this deposit through 1921. The mining of titanium bearing beach sands began in 1916 near Mineral City and Pablo Beach, Fla., for the purpose of making titanium tetrachloride to be used in tracer bullets, flares, and smokescreens. The titanium pigment industry was founded in 1918. By 1928 a large part of the domestic production of rutile, ilmenite, and zircon came from Florida. However production ceased in 1929 in Florida with the mining of newly discovered deposits in Virginia which were mined until 1968. The discovery of new deposits in Florida, and the development of better mining and concentrating methods for lowgrade sands, led to a return of activities in this area. The large deposits near Tahawus, N.Y., were brought into production in 1942 by National Lead Co. (now N L Industries Inc.), and by 1949 this company was the lead¬ing producer of ilmenite in the world. In 1948 the extensive deposits of ilmenite and ilmenite-bearing iron ores were discovered in eastern Quebec." The beginning of the modern titanium metal industry was in 1948, when E. I. du Pont de Nemours & Co. produced the first metal. U.S. Bureau of Mines reports, which gave details of the Kroll process, together with the attractive properties of the metal for

Jan 1, 1975

By Nath S. Parate

Emphasis on publications related to coal mining subsidence and damages is appropriate at present in view of the energy crisis and increased coal production and public alertness. I have worked in Harrisburg with the state government Public Utilities Commission on energy-fuel matters and issues (Parate, 1978-80). I have participated in the communication on subsidence/ damage reviews and status with the Bureau of Mines Liasion Office (Kebblish, 1978-79). I have done research (Parate, 1965) and published papers (Parate, 1972; Parate, 1967) in Britain on coal mining subsidence and damages around Sheffield-Nottinghamshire coal fields. I have a few comments on the recent paper titled, "Pennsylvania Subsidence Control Guidelines," by C.J. Bise. 1) What is the basis of the empirical formula or guideline, LD _ (0.27 x D) ± 4.6, defining the support area? 2) The particular structure may not be damaged due to vertical uniform displacement caused by mining beneath unless the displacement is differential (King, 1964). 3) The author mentions the limited subsidence research in the US, and quite rightly so. But he fails to quote any work reference by continental investigators except the British or review work by the US. What are the reasons? 4) The author has not mentioned the importance and role of angle of draw for Pennsylvania, Kentucky, or Illinois coal fields. Is there any current research investigation on the relationship between subsidence research investigation, damage, and transference of strains to structures? There have been a number of newspaper reports on subsidence damage in Wilkesbarre and other areas in Pennsylvania. Is the author aware of such instances and traditional attitudes to such issues? Many times government agencies--due to lack of funds, technical expertise, and public policies--are unable or do not find it interesting to keep updates on these issues, as per the author's knowledge and experience with state governments. 5) What is the net effect and role of the D.E.R. Insurance Office on the monitoring, reducing, or controlling subsidence damage, particularly in Pennsylvania?

Jan 1, 1983

By William B. Phillips

This paper was prepared at the request of Capt. A. F. Lucas, Chair man of the Institute's Committee on Petroleum and Gas; as a pre1iminary.discussion of the fuel oils which are used in the Southwest, giving their composition, uses, prices, etc. Should it afterward be found desirable, these observations may be extended over a larger area. In this connection, I suggest that samples of all kinds of fuel oils, including various tars, from all over the country, be collected and sent to some testing laboratory for examination. We would be glad to extend the facilities of the laboratory of the Bureau of Economic Geology and Technology, at the University of Texas, for this purpose, and to do the work free of all expenses. After such examinations are made and the results classified and studied, it would be possible to suggest specifications under which fuel oils should be purchased, and to arrive at some conclusions respecting the uniformity of such specifications, with due allowance for climatic and other more or less local conditions. While such specifications do not now depart from a common standard anything like as much as specifications for illuminating oils do, yet there are discrepancies which should not exist. Some of these discrepancies are of lessening importance, due to the pronounced tendency to distill every crude oil that can be distilled with profit, and to send residues into the market for fuel oil. Residues from the refineries are of a more uniform chemical composition and physical nature than many of the crude oils that go direct into the fuel market. The lower flash-point oils are disappearing from the fuel trade and in place of them we are getting oils that do not flash below 220" F., nor burn under 320" F. In the Southwest, it has not been long since we had fuel oils that flashed as low as 110" F., and the average flash point over a considerable period was 151" F. Now we are using oil that flashes at about 30" lower than the former burning point, which was 258" F. In other words, the flash point has risen, on the average, 100"; and the burning point about 75".

Jan 1, 1915

By Norman Braly

THE following is not offered as an extended paper on the subject of shaft sinking, but more as a description of the present practice of shaft sinking in the Butte district. The Anaconda company is sinking at present the following shafts: Badger State, Moose, Mountain Consolidated, Mountain View, Pennsyl-ania and Tropic. At the High Ore and Leonard mines the shafts are being deepened by sinking two compartments and will subsequently be enlarged to the full working size by raising alongside the compartments which are now being sunk. The following other companies are also sinking shafts: Butte-Alex Scott, Butte and Zenith City, Boston and Corbin, North Butte Mining Co. (at the Granite Mountain shaft), East Butte Co. (at the Pittsmont shaft), and the Rainbow Lode Development Co. Shaft Timbering. The shafts of the Butte district, generally speaking, are of three compartments arranged in a straight line, and the pump compartment is usually arranged for the use of an auxiliary hoisting cage, as well as for carrying pipe lines and electric wires. The Rainbow shaft is practically square, and of three compartments. The length of the shafts outside of timber will vary from 17 to 22 ft., and the width from 6 ft. 6 in. to 7 ft. Fir timber is used in all shaft work. This may be obtained from the Coast, when it is known as Coast fir, or from Idaho or Montana, when it is known as native fir. The native fir seems to be the tougher wood, but it is hard to obtain clear lumber in the lengths and sizes necessary for shaft work. Some of the shaft timber of the Anaconda company has been treated with creosote as a preservative, but this practice has not come into general use, as the ground of the camp is so heavy that the timbers usually crush before they rot. The size of timber most .used for shaft work is 12 by 12 in., while 10 by 12 in., 10 by 14 in. and 12 by 14 in. are used for some of the special pieces around the shaft. The new Leonard shaft is timbered with 14 by 14 in. wall plates throughout.

Jan 8, 1913

By A. Singh, W. M. Fleming, J. J. Santana, A. E. Torma

The present study investigated the extraction of uranium from a low-grade ore by sulfuric acid and the removal of radium from the leach residues by brine solutions. The optimum leaching conditions were found to be 1.5 mole [£]-1 H2SO4, 6.Og[9]-1NaClO3, 75°C,50% pulp density and 750 rpm with respect to the rate of uranium extraction. The maximum theoretical attainable rate of uranium extraction was determined to be V = 1.09 x 10 -2 mole [¢]-1h-1 with respect to pulp density. The order of reaction was found to be zero regarding the effect of sodium chlorate concentrations. The apparent activation energy of uranium extraction was calculated from the Arrhenius plot to be [A]E a - 2.36 kcal mole-1 (9.87 kJ mole-1). Based on a statistical design, an empirical equation has been developed describing the rate of uranium extraction with the leaching parameters. This equation can be used to generate data which may be useful for scaling up the process to pilot plant level. The most efficient brine solution for the extraction of radium - 226 from the leach residue was found to contain one mole[f] -1 CaCl2 and 0.01 mole [2] -1 HC1. The two step leaching with this solution resulted 87% removal of radium from the leach residue. On the basis of this study, a flow-sheet has been proposed for the extraction of uranium and radionuclides from the ore and leach residue to yield almost innocuous tailings.

Jan 1, 1982

By H. Hubert

The first attempts at direct utilization of blast-furnace gas in engines were made in 1895. For a considerable time the gas had been burnt in Cowper stoves for heating the blast for the furnace, and under the boilers which supplied steam to the blowing-engines, and others serving the furnaces. It was natural, therefore, that the idea of directly employing it in gas-engines should have occurred simultaneously to several engineers, notably to Lurmann and to Lencauchez, who had pointed out the blast-furnace as a powerful gas-producer. Nevertheless, nowhere had any attempt been made to apply it to this purpose up to the end of 1894, when Thwaite proposed it to Mr. James Riley, of the Glasgom Iron & Steel Company. About the same time investigations were being made in Belgium and in Germany, independently of Thwaite's experiments, which were not generally known on the Continent. The industrial world, which up to that time had hardly favored the idea, had thus been gradually prepared to receive it. The gas-engine, long restricted to small sizes and dependent upon the use of an expensive fuel obtainable only in large centers, now began to make headway. At the Paris Exhibition of 1889 two engines of 100 h.p. were shown and excited much interest among engineers. One had four cylinders, and was made at the celebrated works of the Deutz Company, and the other was a single-cylinder engine, exhibited by two French designers, Messrs. Delamare-Deboutteville and Malandin. In the meanwhile the design of gas-producers had made important progress, completely freeing the new engine from its

Jan 1, 1907

By E. S. Machlin, Morris Cohen

The isothermal formation of martensite in a 71 pct Fe, 29 pct Ni alloy is found to take place mainly by the nucleation of new plates rather than by the growth of existing ones, and is dependent on the temperature and time of the isothermal hold, the amount of atherrnal martensite present, the state of internal strain, and the application of tensile stress. The conclusion is reached that the isothermal nucleation is activated by thermal fluctuations superimposed on localized regions of very high strain. The reaction-path concept, involving martensite nucleation at strain embryos by athermal activation on cooling, or by thermal fluctuations on holding, reconciles the athermal and isothermal modes of transformation, and offers a unified picture of the kinetics of martensite formation. THE phenomenon of isothermal martensite formation has been the subject of considerable study lately,'-' and its reality has been thoroughly established. The existence of such isothermal transformation has been claimed to confirm the nucleation and growth hypothesis as applied to the martensitic reaction.1 " However, the isothermal formation of a martensitic phase is also compatible with the reaction-pathw escription of the transformation. The purpose of this investigation is to examine the isothermal mode of the martensitic reaction, both theoretically and experimentally, in order to test the likelihood of the above two mechanisms. Material and Methods The alloy used in this study contained about 71 pct Fe and 29 pct Ni. The complete analysis was 29.5 ± 0.2 pct Ni, 0.036 pct C, 0.02 pct N, 0.19 pct Mn, 0.09 pct Si, 0.008 pct P, and 0.006 pct S. The amount of isothermal transformation was determined by electrical resistance measurements using a Kelvin double bridge. The specimens were in the form of rods 1/16 in. diam x 4 in. long. Aus-tenitizing was performed at 1095°C for % hr either in a pre-purified nitrogen atmosphere or in an evacuated Vycor tube, followed by oil quenching to room temperature. After this treatment, the samples were completely austenitic, and the transformation studies were conducted at subatmospheric tempera- tures. Lineal analysis and X-ray determinations of retained austenite were used to calibrate the electrical resistance changes in terms of the percentage of martensite. The martensite range curve for this alloy is given in Fig. 9 of ref. 6. The M, temperature occurs at about -18°C (255°K). Reaction-Path Theory The nucleation and growth description of the martensitic transformation that occurs isothermally has already been given by Kurdjumow.','2 However, no comparable treatment exists using the reaction-path concept." Consequently this section presents the reaction-path description of the isothermal mode of the martensitic transformation. According to the latter theory, there is a reaction path (a strain) which describes the relative motion of the atoms during their transference from the austenitic to the martensitic state. The possibility exists, therefore, that the nucleation of a martensitic plate is accomplished by an embryo that comprises a state intermediate between that of austenite and martensite. This state may be attained within a finite volume by means of a homogeneous strain of the austenitic matrix. There is a free-energy barrier (F.) along the reaction path, corresponding to a critical strain in a critical volume. When activation is achieved, a spontaneous increase in strain and volume of the embryo takes place to generate the full-size martensitic plate. This mode of nucleation is to be distinguished from the more conventional mode involving embryos of the martensitic phase that merely grow in size by an interface motion. There are two ways whereby embryos in the austenitic phase can achieve the critical state of strain for isothermal nucleation: 1—through the formation of internal strains by plastic deformation or by stress; and 2—through thermal fluctuations, preferably superimposed upon existing internal strains. The activation free energy F,, must be supplied either mechanically by internal strains or thermally by energy fluctuations, or by a combination of both.

Jan 1, 1953

By R. W. Gurry

In a series of charts this paper presents the composition of all gas mixtures, composed of the elements carbon, hydrogen, oxygen and nitrogen, which at temperatures from 1000° to 1800°F are in equilibrium with (1) austenite of various carbon contents, (2) iron and iron carbide, (3) graphite, (4) iron and its oxide. THIS paper presents the results of calculations made to determine the proportions of CO, CO2, CH4, H2, H2O and N2 in gas mixtures which, at temperatures from 1000" to 1800°F, satisfy, individually, the following conditions: (1) equilibrium with carbon steel of specified carbon content throughout the stable 7 iron region; (2) equilibrium with iron and iron carbide, both above and below the eutectoid temperature; (3) equilibrium with graphite; (4) equilibrium with iron and its oxide. From these data a new type of chart has been prepared which permits one to determine, from a room-temperature analysis of the furnace gas in question, the effect of the gas upon the steel at furnace temperature. Thus a guide is provided as to the carbon content which will result and as to the possibility of oxidation or sooting. All of the atmospheres commonly used in the commercial heat treatment of steel are composed of some or all of the simple constituents CO, CO2, CH4, H2, H2O and N2, and also in some cases oxygen or higher hydrocarbons. As the gas mixture is heated certain alterations in the proportions of the constituents take place, and at the temperature of the furnace the composition is, in general, not at all that of the entering gas. If equilibrium in the gas phase is presumed a calculation involving the use of certain fundamental data predicts for a certain temperature the carburizing, decarburizing, or sooting characteristics of a given atmosphere, and, upon the additional assumption of equilibrium between gas and metal, also the oxidizing ability of the gas and the ultimate carbon content of the steel. The extent to which these predictions are fulfilled will depend upon how closely the assumptions of equilibrium are realized in any particular case. Although at lower temperatures equilibrium is often not reached, there is considerable evidence indicating that above about 1000°F the approach to equilibrium in the gas phase is generally substantially complete, particularly in the vicinity of the steel which acts as a powerful catalyst in promoting reactions in the gas phase. The extent of the gas-metal reactions is commonly affected essentially by the sojourn at temperature; equilibrium with respect to carbon, for example, is accomplished simply by continuing the treatment long enough. However close the approximation of equilibrium may be in any instance, the above mentioned calculation indicates the condition of the steel at equilibrium, and at the present time this is the only basis of control of a furnace atmosphere. The effect at elevated temperature of a gas of a certain composition at room temperature upon a given steel has customarily been judged by first calculating from gas equilibrium constants the proportions of the gas constituents at the temperature of the steel, then comparing certain of these with the proportions known to be in carbon or oxygen equilibrium. This process is tedious and time-consuming, in particular because the calculation generally involves a series of successive approximations; and since some knowledge and familiarity with this type of computation are required, not everyone needing the information has been, in the past, in a position to obtain it. By making a series of equilibrium calculations, combining with fundamental data for gas-metal reactions, and plotting the results in a special way, a chart has been prepared which enables anyone

Jan 1, 1951

By John J. McCabe

INTRODUCTION Over the years, Congress has written into the Internal Revenue Code various provisions aimed at lessening at least one financial burden faced by taxpayers in the mining industry - the federal income tax burden. These provisions include the election to deduct exploration expenses, the election to defer deduction of development expenses, and the percentage depletion deduction. Careful tax planning from the very beginning of a mining venture is essential in taking maximum advantage of these tax benefits. A major decision to be made is the choice of organizational structure. (For a more detailed discussion of this subject, see McCabe, John J., "Developing Structures for Investments in Mineral Property," New York University Institute on Federal Taxation, 42 NYU 24, 1984). One such structure is the use of multiple corporations, with mining activities conducted by one corporation and nonmining activities, such as manufacturing, financing and administration, conducted by the other corporation. This technique, which will be discussed in detail below, can be particularly advantageous in delaying recapture of previously deducted exploration expenses and in maximizing depletion deductions. TAX BENEFITS IN MINING Exploration Subject to certain restrictions discussed below, exploration expenditures (i.e., expenditures paid or incurred during the taxable year for the purpose of ascertaining the existence, location, extent, or quality of any deposit of ore or other mineral, and paid or incurred before the beginning of the development state of the mine are deductible at the election of the taxpayer (Section 617(a)).* Were it not for this option, exploration expenditures would be required to be capitalized and recovered through depletion, after production begins. Exploration of a mineral deposit can be very costly and may not result in commercial production for some time. If the taxpayer has income to he offset by the deductions, a mining venture can usually be structured in such a way as to allow the offset of mining losses against the other income. With today's high interest rates, this election can be quite valuable in present value terms. Corporate and noncorporate taxpayers are subject to different restrictions on this tax benefit. Corporations may elect to deduct only 85 percent of eligible exploration expenditures (Section 291(b)). (The Tax Reform Act of 1984 reduced this to 80 percent effective for expenditures after December 31, 1984, in taxable years ending after such date). The remaining 15 percent (20 percent after December 31, 1984) is capitalized and recovered at the same rate as five-year ACRS property (Section 291(b)). Individual taxpayers are not subject to this 85 percent rule; however, any amount deducted in excess of ten-year straightline amortization is a tax preference item for individuals (Section 57(a)(5)). Individuals may avoid the tax preference by electing to capitalize exploration expenditures and amortize them over ten years (Section 58(i)). In order to prevent the taxpayer from, in effect, converting ordinary income into capital gain by selling property that has given rise to exploration expense deductions, the Code requires recapture of such deductions upon the occurrence of certain events (Section 617): 1. Upon disposition of the property, adjusted exploration expenditures are recaptured to the extent of gain realized on the disposition (Section 617(d)). 2. If the property is leased, the lessor is disallowed any depletion deduction until his adjusted exploration expenditures have been recaptured in the form of foregone depletion deductions (Section 617(c)).

Jan 1, 1985

By R. J. Brison, W. C. Bleimeister

The International Salt Company has long been interested in finding an efficient process for the removal of impurities from rock salt, and particularly from the rock salt produced at the Detroit mine. Methods which have been used previously at the Detroit mine included both hand sorting and differential crushing in a Bradford breaker with rejection of the oversize. Neither of these methods was adequately effective. The development of a new process for removal of impurities from rock salt has been described in the preceding article." Basically, the process consists of exposure of crude rock salt to radiant heating which selectively heats the impure particles. Subsequently the heated particles are removed by adhesion to a heat sensitive-coating on a conveyor belt. This method was found to be effective in improving both the quality and appearance of rock salt by the rejection of the dark, impure particles.

Jan 8, 1960

By Paul Torrey

IN his recent article, Stanley C. Herold described some of the principles involved in oil-field rejuvenation. The purpose of this paper is to present certain facts, based upon observations of systematic water flooding of oil sands in the Bradford and Allegany fields of northwestern Pennsylvania and southwestern New York, which, it is believed, will partially substantiate Mr. Herold's opinions. The writer gratefully acknowledges his obligation to the Forest Oil Corpn., the Kendall Refining Co., the Petroleum Reclamation Co., W. J. Healey, of Bradford, Pa., and the Producers Oil Corpn., of Olean, N. Y., for information included in this article; and he is especially indebted to Jerry B. Newby, of the Petroleum Reclamation Co., for helpful suggestions and criticism in the preparation of the paper. It is obvious that, in the calculation of mathematical formulas for the prediction of oil recovery, uniform conditions must be assumed; otherwise, the applicability of the results of such work will be, by necessity, restricted to the area or individual property for which they were designed. Geologic and physical conditions are so variable throughout the fields where water flooding is practiced that it is difficult to devise methods that can be universally applicable. However, it is believed that there are certain fundamental principles which, when applied with specific modifications designed to meet the conditions existing in local areas or individual properties, may yield considerably greater recoveries of oil.

Jan 1, 1927

By Charles Stein

The effects of several different prior treatments an the creep behavior of 99.9995 pct aluminum at 260°C and 1000 psi canstant stress are compared with annealed specimens. Quenching from 538oC, irradiation with 2 mev electrons, and tension-compression room temperature fatigue damage were used to change the substructure of the specimens prior to their creep testing. The quenched and the irradiated specimens showed a larger primary and transient stage contribution to the creep curve than those specimens which were only annealed prim to creep testing. The specimen receiving prior fatigue damage at room temperature showed no first stage or transient creep when tested under identical conditions as the above specimens and had an average creep rate seven orders of magnitude lower than that of either the annealed, the quenched or the irradiated creep specimens. In a previous electron transmission microscopy investigationl of the substructure developed during the creep of pure aluminum at 0.57 Tm, it was noted that a large concentration of vacancy loops and dislocation loops were present in and near the subboundaries while the interior of the subgrains contained few of these defects and had a low dislocation density, see Fig. 1. Yim and Grant2 and Hazlett3 have shown that the presence in nickel of a substructure developed by prior cold work effectively reduces the primary and transient contributions to the creep curve. Hultgren,4 McLean,5 Gervais, Norton, and Grant,6 Chang and Grant,7 and others have shown the same effect with the higher stacking fault energy material, aluminum. However, the specific defect responsible for the change in the creep behavior developed by the prior cold work was not established. Specifically, what effectively interfered with dislocation motion in these materials at elevated temperatures? Was it jogs on dislocations produced by their interaction with other dislocations or with vacancy or dipole loops, see Fig. 1, or did the subgrain walls determine the mean free path for glissile dislocations? This would be a realistic possibility only if subgrain boundaries are effective barriers to dislocation motion. The ability of a subgrain boundary to act effectively against glissile dislocations depends on the number and the arrangement of dislocations in the subboundary,8 which in turn is a function of the creep strain.' This paper compares the creep rate of specimens possessing a large vacancy concentration to that of annealed specimens and with specimens having a stable subboundary wall containing Lomer locks produced by prior fatigue damage. EXPERIMENTAL PROCEDURE Vacancy Loops. Aluminum creep specimens, 99.9995 pct pure, were machined from zone refined rod to a 2-in. gage length and a cross-sectional area of 0.025 in. These specimens were annealed at 538oC, 1000°F, for 10 min and quenched into ice water. They were then reheated to the creep test temperature of 260°C, 500°F, and held at this temperature for 18 min to al-low for vacancy condensation and loop formation. The specimens were subsequently creep tested at 1000 psi constant stress at 260°C. The temperature along the gage length was monitored by three Pt-Pt, 13 pct Rh thermocouples, two embedded in the upper and lower shoulders of the specimen and one attached to the mid-point of the gage length- The temperature gradient was held to ± l°C or less throughout the Creep test. Elongations were measured by two LVDT's 'connected in an averaging 'On-figuration, with quartz extension arms placed against the specimen at the extremes of the 2-in. gage length. i K 3J?--' * *H - >^> - ' ^L r 77 . *y J OJL, J Fig. 1—Transmission electron micrograph of pure aluminum strained 8.2 pct at 260°C and 1000 psi constant stress. Note the presence of numerous loops near the light dislocation tangle

Jan 1, 1970

By N. M. Levine, W. M. Fassell

In this laboratory study the problem of aerative conditioning to separate chalcopyrite and pyrite from cobaltite was simply effected with a sulfy-drate collector and pH by proper choice of mixing variables. It was shown that for a given impeller type and geometry, selectivity is governed by a relation between the Froude number and a modified power number multiplied by impeller tank-diameter ratio wherein the power factor is expressed as power intensity or horsepower per unit volume of contained pulp. In applying this approach to other systems, other criteria would be used in place of selectivity. The purpose of this paper is to show how solutions to problems of aerative conditioning of pulps may be enhanced by development of mixing parameters in a given system through application of a fundamental approach to agitation. The term aerative conditioning refers to a combination of processes which include mechanical gas dispersion, gas solution in the liquid phase, transport of dissolved gases and other reactants to the reaction zone, physico-chemico interaction within the liquid phase and/or at the solid surface, and, finally transport of products away from the reaction zone. Important elements of these processes are: 1) Air-Liquid Contact Area: This area limits the rate at which a given gas may dissolve in a given liquid. Thus, an aerative conditioning system should be designed for optimum gas dispersion. 2) Diffusional Factors: Such factors as concentration gradient, diffusion film thickness, and diffusivity may govern the rate at which dissolved constituents are transferred to the zone of interaction at a particle surface and the rate at which reaction products are transported therefrom. Thus, such systems would be designed for maximum turbulence to effect good mixing and to minimize diffusion film thickness. 3) Solids-Turbulent Liquid Contact Time: Sufficient time should be provided for interactions to take place at solid-liquid interfaces. The region of maximum turbulence for mechanical systems being in the impeller zone, it is important that the number of passes through this zone be optimized. This means that a proper balance should be struck be- tween flow and turbulent power to achieve optimum conditioning time. Too high a flow rate and insufficient turbulence may be improper if the reactions are diffusion limited. On the other hand, too much turbulent power and too little time in the reaction zone due to insufficient flow power may also be limiting. 4) Geometry and Impeller Design: The design of the conditioning vessel and the type of impeller employed are important factors in determining the relative distribution between flow and turbulent power and the degree of gas dispersion. Maximization of power input would be to no avail if the distribution between flow and turbulent power were improper or gas dispersion insufficient. 5. Physical Chemistry: The reactions between dissolved gases and solid surfaces may be limiting if gas solubility, activation energies and/or free energies are not favorable. J. H. Rushton, E. W. Costich, and H. J. Everett' have summarized the mechanical elements of the combination of processes listed in a fundamental mixing equation. This equation was derived by dimensional analysis and relates the physical variables for a single impeller, centered in a cylindrical, vertical axis, flat-bottomed tank. It is, where T is tank diameter in feet; H is liquid depth in feet; C is height of impeller off tank bottom in feet; S is pitch of impeller; L is length of impeller blades; W is width of impeller blades; R is number of baffles; D is impeller diameter in feet; Np is the power number, pg/dN3D5; P is power in foot-pounds per second; g is the gravitational constant, feet per second; J is width of baffles; B is number of im-

Jan 1, 1961

By John L. Baum

GEOLOGISTS and engineers working around a diamond drill rig have often had the opportunity to observe the magnetic attraction of drill rods pulled out of the hole for core removal. This is sometimes an amusing pastime, but this same magnetic force inadvertently applied to a compass needle can cause it to lose its polarity entirely or to become reverse polarized when placed in the immediate vicinity of stacked rods. The first recommendation, of course, would be to avoid the rods, but in surveying an operating drillhole this is not always possible; therefore steps must be taken to neutralize the magnetic effect of the drill rods. Early in the summer of 1949 the geological department of the New Jersey Zinc Co. undertook at Franklin, N. J., an extensive program of surveying the course of deep diamond drillholes. The majority of the holes were surveyed while in the process of being drilled, and considerable difficulty was encountered. A pattern for the deviation of drillholes had been established for the district from surveys in holes from which the drill rig had been removed. It was observed that a certain operating deep drill- hole being surveyed did not fit this pattern. In the resulting confusion of repeated surveys and cementing a plug for wedging operations, the lower 1800 ft of the hole was lost. Because of this incident studies were initiated to determine the source of the difficulties and to develop safeguards against recurrence of faulty surveys.

Jan 12, 1954