Search Documents

By Hugh H. Waesche

AN adequate supply of crystalline quartz of piezoelectric grade and size continues to be of fundamental importance to the U. S. Army Signal Corps. Current electronic development programs of the Armed Forces depend upon the use of quartz crystals in all applications where accurate frequency control is necessary. In peacetime this' may not seem too significant, but in planning for possible national defense emergencies, an adequate supply of piezoelectric grade raw quartz is just as important as an adequate supply of some of the more publicized strategic minerals. Prior to World War II, the Signal Corps accepted the use of quartz crystals for frequency-control purposes in essentially all electronic communication, navigation, and radar equipment operating in the audio and radio frequency spectra up to and including the ultra-high-frequency channels. Over 4,000; 000 lb of radio-grade quartz was required between January 1942 and V.J Day. Use of such a large quantity of crystal units was necessary in order to establish and maintain, with a minimum of effort, clear and definite frequency channels of greater stability than could be obtained by any other means. This policy was justified on the basis that quartz was without a peer as a frequency-controlling element. Military and civilian uses of quartz in the field, as well as laboratory studies, have confirmed this premise and no means of highly stable frequency control, superior to quartz, has been discovered. It appears certain that the demand for use of quartz for frequency control purposes will continue at a high level.

Jan 1, 1948

By R. Moldenke

The presence of nickel-chromium in pig iron made fro111 Cuban oles is so well known that the word "Mayari" is unconsciously associated with it. Since 1904, when exploration of the Mayari deposits of iron ore in northeastern Cuba was undertaken, there llas been increasing interest in these ores. Tlie Transactions contain numerous references to t1ieln.l This iron ore, which is shipped to the Tinited States in the nodulizecl state, has been thoroughly tested and found very valuable; the deposit covers over 25,000 acres and there is in sight over 500,000,000 tons of ore that, by systematic mining, runs practically constant in composition. With nickel and chromium present, also titanium in sufficient quantities to attract attention, as well as extremely low phosphorus and sulfur contents, the iron founder is naturally interested in the utilization of RInpari ore for pig iron for the better grades of finishrtl iron products. The present point of coilsn~iil)tion ol ILlapri ore is at Sparrow's Poi111, where hlayari pig iron of ally desiretl coml>osition is made. The composition of the dried ore is about as follows: Iron -29 per cent., silica 3 pc.r cent., nickel 1 per cciit., chroiniun~ 1.5 per cent., alumina 11 per cent., ant1 coinbined water 13 per cent. When nodulized, the iron runs up to nearly 56 per cent., the silic:~, :tlumi~i:i, nickel, and c~llromiurn are slightly highr than the arno~l~its just given. Practically all the, combined wntcr is driven off aild the iiodulizccl ore carries only a few- tenths per cent. of 1 C. M. Weld: Residual Rrolvn Iron Ores of Cuba. Tmns, (1909) 40, 299. C. K. Leitll nnd If'. J. Mcncl: Origin of Iron Ores of Central and Northeostr~n rlbn. Trans (1911) 42, 00. C. W. Hayes: May:~ri and Mos Iron-ore Deposits in Cuba. Idem, 109. J. E. Little: Maynri lron Mincs, as Developed by the Spanish-American Iron ('0. Idem, 152. J. F. Iie~np: M'ryari Iron-ore Dcposi(s. Trans. (1915) 61, 3. C. K. Leith 2nd N. J. Mead: Additional Data on Origin of Lateritic Iron 01cs or Eastern Cubn. Tmns. (1916) 63, 75.

Jan 1, 1923

By R. Moldenke

The presence of nickel-chromium in pig iron made fro111 Cuban oles is so well known that the word "Mayari" is unconsciously associated with it. Since 1904, when exploration of the Mayari deposits of iron ore in northeastern Cuba was undertaken, there llas been increasing interest in these ores. Tlie Transactions contain numerous references to t1ieln.l This iron ore, which is shipped to the Tinited States in the nodulizecl state, has been thoroughly tested and found very valuable; the deposit covers over 25,000 acres and there is in sight over 500,000,000 tons of ore that, by systematic mining, runs practically constant in composition. With nickel and chromium present, also titanium in sufficient quantities to attract attention, as well as extremely low phosphorus and sulfur contents, the iron founder is naturally interested in the utilization of RInpari ore for pig iron for the better grades of finishrtl iron products. The present point of coilsn~iil)tion ol ILlapri ore is at Sparrow's Poi111, where hlayari pig iron of ally desiretl coml>osition is made. The composition of the dried ore is about as follows: Iron -29 per cent., silica 3 pc.r cent., nickel 1 per cciit., chroiniun~ 1.5 per cent., alumina 11 per cent., ant1 coinbined water 13 per cent. When nodulized, the iron runs up to nearly 56 per cent., the silic:~, :tlumi~i:i, nickel, and c~llromiurn are slightly highr than the arno~l~its just given. Practically all the, combined wntcr is driven off aild the iiodulizccl ore carries only a few- tenths per cent. of 1 C. M. Weld: Residual Rrolvn Iron Ores of Cuba. Tmns, (1909) 40, 299. C. K. Leitll nnd If'. J. Mcncl: Origin of Iron Ores of Central and Northeostr~n rlbn. Trans (1911) 42, 00. C. W. Hayes: May:~ri and Mos Iron-ore Deposits in Cuba. Idem, 109. J. E. Little: Maynri lron Mincs, as Developed by the Spanish-American Iron ('0. Idem, 152. J. F. Iie~np: M'ryari Iron-ore Dcposi(s. Trans. (1915) 61, 3. C. K. Leith 2nd N. J. Mead: Additional Data on Origin of Lateritic Iron 01cs or Eastern Cubn. Tmns. (1916) 63, 75.

Jan 1, 1923

By F. S. Norcross

DEVELOPMENT of the manganese deposits of Cuba is a matter of importance not only to those involved in this industry on the Island but to the United States steel industry and to our Nation as a whole. For years our domestic resources of manganese have been wholly inadequate, but the recent Cuban development points the way toward solution of this strategic mineral problem.

Jan 1, 1939

By H. B. Pulsifer

.ABOut 1.5 varieties, or tnodifications, of the best rnagnesiurn available were prepared and subjected to etching tests, then examined for micro-structure. Of the 30-udd etching reagents that were tried, nearly half, mostly ammonium salts, etched the metal satisfactorily. The surfacing and etching of magnesium is shown to be a very simple and quick operation. The density and hardness of magnesium were determined. The most interesting new observations relate to the finding of the hexagonal etch figures, the crystal laminations, and the fact that the metal is plastic, cold, when restrained or quickly deformed. Under slowly applied pressule cold metal deforms slightly, then shears to fracture without plastic flow. The chief structural features of magnesium arc presented in two reduced photographs and 30 photomicrographs. Materials Tested There are only two sources in the United States from which new metal can be procured: the American Magnesium Corpn. and the Dow Chemical Co. No pronounced structural or property differences in the metals from these two companies were disclosed by the work of this investigation. The following materials were obtained from the manufacturers: 1. Massive crystals of distilled metal (American Magnesium Corpn.). 2. Rods of hot-extruded metal, ½-in. squares and 5/8-in. rounds (American Magnesium Corpn.). 3. Sheet magnesium, 0.005-in. thick (American Magnesium Corpn.). 4. Cast stick metal, 13/8-in. dia. (Dow Chemical Co.). 5. Magnesium-aluminum alloy, hot-rolled plate, ½-in. thick (American Magnesium Corpn.). From these materials, were prepared: 6. Sections from a furnace-cooled ingot made from clistilled crystal. 7. Cold-strained pieces from (6), (4) and (2). 8. Pieces cold-squeezed to fracture from (6), (4) and (2). 9. Hammer-struck pieces from (6), (4) and (2). 10. Steam-hammer struck pieces from (6), (4) and (2). 11. Sections from furnace-cooled ingot of the magnesium-aluminum alloy.

By H. B. Pulsifer

ABOUT 15 varieties, or modifications, of the best magnesium available were prepared and subjected to etching tests, then examined for microstructure. Of the 30-odd etching reagents that were tried, nearly half, mostly ammonium salts, etched the metal satisfactorily. The surfacing and etching of magnesium is shown to be a very simple and quick operation. The density and hardness of magnesium were determined. The most interesting new observations relate to the finding of the hexagonal etch figures, the crystal laminations, and the fact that the metal is plastic, cold, when restrained or quickly deformed. Under slowly applied pressure cold metal deforms slightly, then shears to fracture without plastic flow. The chief structural features of magnesium are presented in two reduced photographs and 30 photomicrographs. MATERIALS TESTED There are only two sources in the United States from which new metal can be procured: the American Magnesium Corpn. and the Dow Chemical Co. No pronounced structural or property differences in the metals from these two companies were disclosed by the work of this investigation. The following materials were obtained from the manufacturers: 1. Massive crystals of distilled metal (American Magnesium Corpn.). 2. Rods of hot-extruded metal, ½ -in. squares and 5/8-in. rounds (American Magnesium Corpn.). 3. Sheet magnesium, 0.005-in. thick (American Magnesium Corpn.). 4. Cast stick metal, 1 3/8-in. dia. (Dow Chemical Co.). 5. Magnesium-aluminum alloy, hot-rolled plate, ½ in. thick (American Magnesium Corpn.). From these materials, were prepared: 6. Sections from a furnace-cooled ingot made from distilled crystal. 7. Cold-strained pieces from (6), (4) and (2). 8. Pieces cold-squeezed to fracture from (6), (4) and (2). 9. Hammer-struck pieces from (6), (4) and (2). 10. Steam-hammer struck pieces from (6), (4) and (2). 11. Sections from furnace-cooled ingot of the magnesium-aluminum alloy.

Jan 1, 1928

By J. D. Hunt, R. J. McDonald

It is proposed that extensive fluid motion occurs between the dendrites of a Partially solid casting and it is suggested the A segregates in steel castings are a direct result of this motion. The fluid flow arises because of density differences between liquid ahead of the dendrites and the interdendritic liquid. Experiments are described on a model system investigating this fluid motion. The importance of interdendritic fluid flow is discussed with reference to longitudinal segregation. SERIOUS macro segregation is often found in large killed steel ingots. Among the most common segregates are those known as A and V, Fig. 1. The A segregates are arranged over the surface of cones, the wide parts being at the base of the ingot. The A segregates are pencil like in shape and extend from the columnar into the equiaxed region. The V segregates are distributed over inverted cones but have a less well defined shape. They occur at the center of the ingot. Because of the commercial importance of macro inhomogenities these segregates have attracted wide-scale attention. The segregates contain alloying elements and impurities which depress the freezing temperature and are thus the last liquid to freeze. A number of explanations have been proposed to explain their presence. It has been suggested1'' that the segregates are the result of the equiaxed zone growing towards the columnar region together with the interaction of convection within the bulk liquid. It has also been proposed that the segregates are the result of nucleation and rapid growth ahead of the dendritic front.3 Neither of these explanations is completely satisfactory because A segregates are pencil shaped and are not found as continuous cones. In this paper an alternative mechanism is proposed, and experiments are described on a model system to determine whether the mechanism occurs in practice. It is thought that A and V segregates are not peculiar to steels but should occur in many other large castings. Fluid motion within the bulk liquid region of a casting has been extensively discussed. Little attention has been paid to fluid motion within the partially solid regions. The work415 that has been done has been mainly concerned with the fluid motion which results from the volume contraction on freezing. The volume contraction is used to explain various types of macro segregation. The present authors suggest that in many cases the fluid flow resulting from volume contraction will be small compared with that due to other causes. When the columnar region is growing, the liquid still remaining between the dendrites has a much lower temperature near the ingot walls than at the dendrite tips. The composition of the liquid in contact with solid will vary with temperature. The density of the liquid will thus vary both because of changes in temperature and composition. The layers of different density liquid will give rise to a slow but steady liquid flow through the interdendritic regions. If there is no density change with composition, the temperature gradient within the dendritic region should give rise to a downward flow between the dendrites, shown schematically in Fig. 2. When the liquid density changes appreciably with alloy concentration this motion could either be en-

Jan 1, 1970

By C. A. Hartnagel, D. H. Newland

Most of the petroleum produced in New York State is obtained by flooding; that is, water drive. No important oil fields have been developed during the past 30 years, nor does there seem much hope that the productive oil areas will be substantially enlarged in the future. There is some prospect that additional supplies may be obtained by deeper drilling, but deep tests for gas to the Oriskany sandstone in some of the oil-producing areas have been without results so far as any discoveries of oil are concerned. Although the flooding method had been made legal in 1919, and some floods had been in operation previous to 1921, that year marks the beginning of a rapid increase in oil production by the new method. The flush production of oil in New York was in 1882, shortly after the discovery of the Richburg pool in Allegany County. The oil production in that year amounted to 6,685,000 bbl. The 1937 production of 5,478,000 bbl. was the largest since the flush production of 55 years ago. The effectiveness of water-flooding for increasing oil production from the old New York fields is shown in Table 1. Table 1.—Production of Oil in New York since 1921 Year Barrels Year Barrela 1921 988,000 1929 3,377,000 1922 1,000,000 1930 3,647,000 1923 1,250,000 1931 3,363,000 1924 1,440,000 1932 3,508,000 1925 1,695,000 1933 3,181,000 1926 2,242,000 1934 3,804,000 1927 2,603,000 1935 4,236,000 1928 3,377,000 1936 4,633,000 1937 5,478,000 The area of the New York oil fields is about 60,000 acres. It has been estimated that not over one-fourth of the area is being flooded. Very little of flooded territory has ceased to produce. Some leases flooded by the early, less scientific methods are being again subjected to the water

Jan 1, 1938

By Orville R. Lyons

DISCUSSION Judson S. Hubbard (The Humphreys Investment Co., Denver)—In this very interesting paper several brief references are made to the Humphreys spiral, a device used for cleaning fine coal. In Table I, Plants 76 and 77, data are given on spiral performance treating Raton and Trinidad coal. The fine coal, as fed to the spiral in these instances, is actually a table middling, hence the more easily treated material was previously removed and a large number of particles were present which were difficult to clean. Mr. W. M. Bertholf of the Colorado Fuel and Iron Co. presented a paper in February, 1946, Cleaning Table Middlings from a Coal Washery with the Humphreys Spiral Concentrator, from which I quote: "In considering the results of our tests it should be noted that the feed was our table middling, and that any real separation is a 'moral victory' as there is little material that could properly be called coal and practically no heavy rock, the consequences being that previous attempts to clean the middling have not at all been successful." Referring again to Table I, Plants 72, 73, 74, and 75, these data were obtained by Yancey and Geer and others and presented at the February 1950 Meeting, AIME, in a paper entitled Laboratory Performance Tests of the Humphreys Spiral as a Cleaner of Fine Coal. Results shown for those tests involve all particles from 8 mesh through the colloids, which admittedly is not an ideal situation for spiral feed if much refuse is contained in the —80 mesh or —100 mesh size range. As an illustration of the effect of treating too broad a size range, let us consider Plant No. 75, Kentucky No. 9 seam. Spiral feed was 8 mesh x 0. Now had this been 8x100 mesh the percentage of misplaced material would have been 8.0 pct instead of the reported 15.26 pct. Similar comparisons can be made on the other data presented with respect to the spiral. Other types of equipment show a similar trend in that whenever too fine a size is treated in a given unit process the percentage of misplaced material increases. Since the spiral is working near the finer end of the size range, it will sometimes be advantageous to treat the entire range of —8 mesh material rather than to deslime and make a fair showing on, say, the +80 or + I00 mesh. Desliming is subsequently done in any case in the dewatering or thickening operation. Results obtained by spiraling any given coal depend on factors too numerous and complex to discuss here, but there are strong indications that proper preparation of feed to the spiral can improve results obtained on some of the raw coals tested. This is clearly pointed out at the end of the aforementioned paper by Yancey and Geer. "The spiral is an extremely simple device which involves no moving parts and is constructed almost entirely of unmachined castings. Since it is such an uncomplicated mechanism, operation is simple and virtually foolproof. These characteristics, which go far toward insuring low cost operation, are attractive attributes in any coal cleaning unit." Certain equipment used in conjunction with the spiral has resulted in a decrease in the percentage of misplaced material, notably in actual practice the launder screen which is used to remove objectionable high ash fines from a spiral-washed coal product. Private correspondence with the U. S. Bureau of Mines has intimated that an additional yield of coal is possible by flotation of the spiral middling. Possible future improvements and developments may result from other methods now under consideration. Finally, some compromise must be made between the best metallurgical performance and the best practical or economical results. Mr. Lyons emphasizes in his summary this objective of overall economy in selection of equipment. G. B. Walker (American Cyanamid Co., Stamford, Conn.)—I had the pleasure of reviewing the draft of this paper and my curiosity was aroused by the data given for Tromp plants, in that all of the examples shown appeared to be 2-product separations, whereas all the Tromp plants with which I am familiar have been 3-product units. The data given for plants No. 101 and 102 appear to be taken from Tromp's brochure on his process and represent the results obtained at the Dominale plant in Holland which was operated for many years by Mr. Tromp. The plant, which was designed to treat 58 tons per hr, was sampled while treating 35 tons per hr of 3Y4x-in. coal. Example 101 appears to conform to what would result if the middling product were calculated into the refuse product, while Example 102 represents the calculation of the middling into the coal product. It is believed that Examples 103 and 104 represent the operation of the Willem-Sophie Mine in Holland recalculated on the same basis. In checking the English examples given by numbers 14, 15, 16, and 17, the same procedure seems to have been followed. These results have, apparently, been taken from an article in Colliery Engineering in August 1941, describing the initial operation of the Williamthorpe Colliery of the Hardwick Colliery Co. Two vessels are employed in this plant, one to treat soft coal and one to treat hard coal. Example No. 14 presents the results that could be obtained from the soft coal bath if the middling were calculated into the refuse, and Example 15 the results when the middling is calculated into the coal. Examples 16 and 17 represent the same expedient in the case of the hard coal bath. Of interest to this discussion is the fact that during the past year the Simon-Carves Engineering Co. in England has installed in the Williamthorpe plant their new "Sim-Car" medium cleaning system which is based on magnetic extraction and control and which is licensed under the Heavy-Media Separation Processes patents by the American Zinc, Lead and Smelting Co. This system has been described in the December 1951, issue of Colliery Engineering. It is reported that since the Williamthorpe Colliery was changed from the Tromp system of medium cleaning to the Magneto-Motive method of medium control the opera-

Jan 1, 1953

By Orville R. Lyons

DISCUSSION Judson S. Hubbard (The Humphreys Investment Co., Denver)—In this very interesting paper several brief references are made to the Humphreys spiral, a device used for cleaning fine coal. In Table I, Plants 76 and 77, data are given on spiral performance treating Raton and Trinidad coal. The fine coal, as fed to the spiral in these instances, is actually a table middling, hence the more easily treated material was previously removed and a large number of particles were present which were difficult to clean. Mr. W. M. Bertholf of the Colorado Fuel and Iron Co. presented a paper in February, 1946, Cleaning Table Middlings from a Coal Washery with the Humphreys Spiral Concentrator, from which I quote: "In considering the results of our tests it should be noted that the feed was our table middling, and that any real separation is a 'moral victory' as there is little material that could properly be called coal and practically no heavy rock, the consequences being that previous attempts to clean the middling have not at all been successful." Referring again to Table I, Plants 72, 73, 74, and 75, these data were obtained by Yancey and Geer and others and presented at the February 1950 Meeting, AIME, in a paper entitled Laboratory Performance Tests of the Humphreys Spiral as a Cleaner of Fine Coal. Results shown for those tests involve all particles from 8 mesh through the colloids, which admittedly is not an ideal situation for spiral feed if much refuse is contained in the —80 mesh or —100 mesh size range. As an illustration of the effect of treating too broad a size range, let us consider Plant No. 75, Kentucky No. 9 seam. Spiral feed was 8 mesh x 0. Now had this been 8x100 mesh the percentage of misplaced material would have been 8.0 pct instead of the reported 15.26 pct. Similar comparisons can be made on the other data presented with respect to the spiral. Other types of equipment show a similar trend in that whenever too fine a size is treated in a given unit process the percentage of misplaced material increases. Since the spiral is working near the finer end of the size range, it will sometimes be advantageous to treat the entire range of —8 mesh material rather than to deslime and make a fair showing on, say, the +80 or + I00 mesh. Desliming is subsequently done in any case in the dewatering or thickening operation. Results obtained by spiraling any given coal depend on factors too numerous and complex to discuss here, but there are strong indications that proper preparation of feed to the spiral can improve results obtained on some of the raw coals tested. This is clearly pointed out at the end of the aforementioned paper by Yancey and Geer. "The spiral is an extremely simple device which involves no moving parts and is constructed almost entirely of unmachined castings. Since it is such an uncomplicated mechanism, operation is simple and virtually foolproof. These characteristics, which go far toward insuring low cost operation, are attractive attributes in any coal cleaning unit." Certain equipment used in conjunction with the spiral has resulted in a decrease in the percentage of misplaced material, notably in actual practice the launder screen which is used to remove objectionable high ash fines from a spiral-washed coal product. Private correspondence with the U. S. Bureau of Mines has intimated that an additional yield of coal is possible by flotation of the spiral middling. Possible future improvements and developments may result from other methods now under consideration. Finally, some compromise must be made between the best metallurgical performance and the best practical or economical results. Mr. Lyons emphasizes in his summary this objective of overall economy in selection of equipment. G. B. Walker (American Cyanamid Co., Stamford, Conn.)—I had the pleasure of reviewing the draft of this paper and my curiosity was aroused by the data given for Tromp plants, in that all of the examples shown appeared to be 2-product separations, whereas all the Tromp plants with which I am familiar have been 3-product units. The data given for plants No. 101 and 102 appear to be taken from Tromp's brochure on his process and represent the results obtained at the Dominale plant in Holland which was operated for many years by Mr. Tromp. The plant, which was designed to treat 58 tons per hr, was sampled while treating 35 tons per hr of 3Y4x-in. coal. Example 101 appears to conform to what would result if the middling product were calculated into the refuse product, while Example 102 represents the calculation of the middling into the coal product. It is believed that Examples 103 and 104 represent the operation of the Willem-Sophie Mine in Holland recalculated on the same basis. In checking the English examples given by numbers 14, 15, 16, and 17, the same procedure seems to have been followed. These results have, apparently, been taken from an article in Colliery Engineering in August 1941, describing the initial operation of the Williamthorpe Colliery of the Hardwick Colliery Co. Two vessels are employed in this plant, one to treat soft coal and one to treat hard coal. Example No. 14 presents the results that could be obtained from the soft coal bath if the middling were calculated into the refuse, and Example 15 the results when the middling is calculated into the coal. Examples 16 and 17 represent the same expedient in the case of the hard coal bath. Of interest to this discussion is the fact that during the past year the Simon-Carves Engineering Co. in England has installed in the Williamthorpe plant their new "Sim-Car" medium cleaning system which is based on magnetic extraction and control and which is licensed under the Heavy-Media Separation Processes patents by the American Zinc, Lead and Smelting Co. This system has been described in the December 1951, issue of Colliery Engineering. It is reported that since the Williamthorpe Colliery was changed from the Tromp system of medium cleaning to the Magneto-Motive method of medium control the opera-

Jan 1, 1953

TO THE BOARD OF DIRECTORS AND MEMBERS OF THE AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS. GENTLEMEN: Submitted herewith are the report of the Treasurer for the year 1941 and re¬ports for the same year of the following standing committees: Admissions, Mem¬bership, Papers and Publications, Mining and Metallurgy (Magazine), Library, and Student Relations. These reports present additional details. Membership For the fourth year in succession, mem¬bership reached a new all-time high, level as shown in Table 1. The total at the

Jan 1, 1942

By R. Floyd Farris

Al thorough knowledge of the behavior of cement slurries under elevated temperatures and pressures is necessary in order to solve properly the many problems presented in deep-well cementing operations. In the earlier days of the petroleum industry the depths of wells were shallow as compared to those of today, and the subsurface temperatures and pressures were not of sufficient magnitude to affect seriously the problem of proper control of cement-slurry properties. Today, however, the search for new reserves has extended drilling to such depths that bottom-hole temperatures of more than 200°F. and bottom-hole pressures of 3000 to 5000 lb. are not uncommon. Moreover, there is every indication that within the next few years wells will be drilled to even greater depths and bottom-hole temperatures and pressures will be correspondingly higher than those with which we are concerned today. It has been realized for some time that the behavior of cement slurries at high temperatures and pressures might be very different from that at atmospheric tempera-ture-pressure conditions, but while the temperature effects have been investigated with a reasonable degree of thoroughness, the pressure effects have received little public attention. While the trend toward deeper drilling may make changes in cementing technique and the choice of cements imperative, it was the purpose of this investigation to consider factors having a bearing on the latter, only secondary consideration being ,given, for the present, to details of tech-nique and equipment for oil-field use. More specfically, the purpose of this work was to consider the effect of temperature and pressure upon the behavior of cement slurries. Although it has long been recognized that cements thicken and set rapidly with increasing temperatures, practical methods for the quantitative determination of these effects are comparatively recent developments. In 1935 Silcox and Rule1 presented such a method, describing apparatus designed to measure the consistency-time relationship of cement slurries at relatively high temperatures. The practical importance of this apparatus in furnishing useful data for the evaluation of cement slurries for cementing operations has been emphasized in various technical publications by such writers as E. L. Davis,~ I. F. Bing-ham,3 and J. E. Weiler.4 A paper describing the numerous tests now used to evaluate cements for oil wells was presented in 1939 by W. W. Robinson.= Robinson describes the Consistometer and the Thickening-Time Tester, showing similarity of data from the two devices, and points out that the purpose of each apparatus is to determine the allowable time that a cement may be pumped at a given temperature. At the present time, however, it is believed that results from the Thickening-Time Tester and the Consistometer have not given a

Jan 1, 1941

By R. Floyd Farris

Al thorough knowledge of the behavior of cement slurries under elevated temperatures and pressures is necessary in order to solve properly the many problems presented in deep-well cementing operations. In the earlier days of the petroleum industry the depths of wells were shallow as compared to those of today, and the subsurface temperatures and pressures were not of sufficient magnitude to affect seriously the problem of proper control of cement-slurry properties. Today, however, the search for new reserves has extended drilling to such depths that bottom-hole temperatures of more than 200°F. and bottom-hole pressures of 3000 to 5000 lb. are not uncommon. Moreover, there is every indication that within the next few years wells will be drilled to even greater depths and bottom-hole temperatures and pressures will be correspondingly higher than those with which we are concerned today. It has been realized for some time that the behavior of cement slurries at high temperatures and pressures might be very different from that at atmospheric tempera-ture-pressure conditions, but while the temperature effects have been investigated with a reasonable degree of thoroughness, the pressure effects have received little public attention. While the trend toward deeper drilling may make changes in cementing technique and the choice of cements imperative, it was the purpose of this investigation to consider factors having a bearing on the latter, only secondary consideration being ,given, for the present, to details of tech-nique and equipment for oil-field use. More specfically, the purpose of this work was to consider the effect of temperature and pressure upon the behavior of cement slurries. Although it has long been recognized that cements thicken and set rapidly with increasing temperatures, practical methods for the quantitative determination of these effects are comparatively recent developments. In 1935 Silcox and Rule1 presented such a method, describing apparatus designed to measure the consistency-time relationship of cement slurries at relatively high temperatures. The practical importance of this apparatus in furnishing useful data for the evaluation of cement slurries for cementing operations has been emphasized in various technical publications by such writers as E. L. Davis,~ I. F. Bing-ham,3 and J. E. Weiler.4 A paper describing the numerous tests now used to evaluate cements for oil wells was presented in 1939 by W. W. Robinson.= Robinson describes the Consistometer and the Thickening-Time Tester, showing similarity of data from the two devices, and points out that the purpose of each apparatus is to determine the allowable time that a cement may be pumped at a given temperature. At the present time, however, it is believed that results from the Thickening-Time Tester and the Consistometer have not given a

Jan 1, 1941

By D. R. Parrish, V. J. Berry

Reverse combustion is one thermal method of recovering hydrocarbons from porous undergrortnd formations containing oil or tar. In applying this method, air is introduced via an injection well and the mixture of air and hydrocarbons is ignited in the production well. A combustion zone then recedes toward the injection well, counter-current to the air flow. If the combustion-zorie temperature is sufficiently high, the oil or tar irz place is distilled arid cracked. The hydrocnrhon flows as a vapor to the production well and subsequently is condensed at the surface. Maximum temperature and velocity of morcment arc the two dependent variubles defining the progress of the combustion zone. A theoretical analysis has been made of heat flow in the reverse-comhustion process as.srtrning linear flow in a homogeneous system. The differentirll equatious, which include the oxygen-hydrocar-hon rctrction rate, have been solved numerically. Rescllts indicate that the maximum temperature reached and he cornbustion-zone relocity both increase with an incrense in air-injection rote. Heat loss to surroundings has little effect on the maximum comhustion-zone ten?perature achieved, but it is reflected in a reduced com-bustion-zorzc, velocity. It is also predicted that an increase in the oxygen-hydrocarbon reaction rate results in a reduction in the maximum temperature reached. The calculated results are in agreement with results from reverse-combustion experinments using samples of a tar sand. INTRODUCTION Reverse combustion is one thermal method of recovering hydrocarbons from porous underground forma-tions containing oil or tar.' In applying this method, air is introduced into the underground formation via an in-jection well. In one or more adjacent production wells, the mixture of air and hydrocarbons is ignited at the sand face. The combustion zone thus formed recedes toward the injection well, counter-current to the air flow (Fig. 1). Under certain conditions, the rate of recession of the combustion zone is sufficiently rapid that only a small fraction of the hydrocarbon at any point in the formation is consumed by combustion. If the combustion-zone temperature is sufficiently high, the uncon-sumed oil or tar in place may be partially distilled or cracked. This material then can flow as a vapor with the gaseous combustion products to the production well and subsequently be condensed at the surface. Under other conditions, the combustion-zone temperature may be so low that little, if any, of the hydrocarbon is vaporized. Nevertheless, the viscosity of the hydrocarbon may be reduced enough so that other recovery methods subsequently can be applied to produce oil at attractive rates. The maximum temperature achieved in the combustion zone and the velocity of movement are the two dependent variables defining the progress of the combustion zone. Presumably. knowledge of these factors will permit estimates to be made of oil recovery efficiency, oil and gas producticn rates and average amount of injection air required per barrel of oil recovered. The maximum temperature and combustion-zone vclocity are, in turn, expected to be dependent upon air flow rate, heat losses to surrounding formations, physical properties of the rock and the hydrocarbon. the extent to which the porous formation is saturated with the hydrocarbon, the rate of oxidation of the hydrocarbon and the amount of heat released. It is desirable that the relative importance of each of these factors be understood so that the results of laboratory tests of oil recovery by reverse combustion can be properly interpreted in terms of expected field performance. It is particularly desirable to assess the importance of heat lcsses because these are difficult to control or eliminate

By S. E. Szasz, E. J. Moore, B. F. Whitney

An accurate value of formation water resistivity R, is essential in calculating formation porosity and fluid saturation from electrical well logs. In the cases where R, has not been measured directly, it must be obtained from other data, e.g., the SP curve. This paper deals with another approach: how to calculate R, from the chemical analysis of the formation water. INTRODUCTION It is known that the resistivity of aqueous solutions of pure salts depends on their concentration and on the temperature; the concentrations are given in MPL (mg of solute per liter of solution), or sometimes in ppm (mg of solute per kg of solution): MPL = ppm X specific gravity. Values for different pure salts are available in the literature, but not for solutions of mixtures which are of practical interest. The major component of the dissolved material in almost all formation waters being sodium chloride, it is customary to express the resistivity of formation waters in terms of equivalent sodium chloride concentration, i.e., the concentration of a solution of pure NaCl which has the same resistivity at a given temperature as that of the formation water under consideration. Thus, the problem of calculating R, from the chemical anaylsis can also be stated as how to convert the other constituents of the solute into equivalent NaCl concentration. Salts dissolved in water are at least partly dissociated into ions, and do not conserve their identity. If known amounts of several salts are dissolved in water, the solution does not necessarily contain the same salts in the original proportion, but perhaps some other combination of the ions, along with free ions in solution. This is why the chemical analysis of formation waters is often given in terms of ions, as if all dissolved salts were completely dissociated. Our problem then boils down to how to convert the concentrations of the various ions to equivalent concentrations of Na' and C1-. Dunlap and Hawthorne' have proposed to convert the concentration of all other ions to equivalent Na' and C1-concentrations by means of constant multipliers; e.g., 0.95 for Ca"; 2.0 for Mg"; 0.27 for HCO 3-; 0.5 for SO, -, etc. Their factors were based on measurements made at 68F on 26 formation water samples from the Texas Gulf Coast, ranging in concentration from 1,500 to 75,000 ppm. The Dunlap method is widely used in electric log interpretation, and is often extrapolated beyond its original concentration range. A comparison of R, values calculated by this method and values actually measured on formation water samples has shown large discrepancies, especially at higher concentrations. Therefore, two new methods were developed at Sinclair Oil Corp.'s Tulsa Research Center to calculate equivalent sodium chloride concentration from the chemical analysis of formation water samples. FUNDAMENTAL CONSIDERATIONS The resistivity of a solution, or its reciprocal the conductivity, at a given temperature is determined by the charge, concentration and mobility of the ions actually present. Monovalent ions such as Na' or C1- always carry the same charge. Compounds of polyvalent ions, however. may show incomplete dissociation, e.g., NaSO; + Na' instead of SO,-- + 2Na'. This happens especially in more concentrated solutions. Only very dilute solutions are completely dissociated, as assumed in the chemical analysis report. At higher concentration, the degree of dissociation depends not only on the nature and concentration of the particular salt under consideration but also on the nature and concentrations of the other solutes. Mobility of the ions depends on the viscosity of the solution. It also depends on the degree of hydration of the ions, which in turn is a function of the nature and the charge of the ions and also of the amount of free water available per ion, i.e., the total ionic concentration. The net effect is that the conductivity increases slower than proportional to the concentration, even if a solution contains only one salt such as NaC1, and is different for different salts (Fig. 1). Conductivity can even decline with a further increase in concentration, e.g., if additional salt is little dissociated but ties up some of the free water and/or causes an increase in viscosity. In solutions containing more than one salt, the contribution of one salt to the total conductivity depends not only on the fractional concentration of this same salt, but also on the concentration of all other solutes. A perfect method would give the conductivity or resistivity of a solution as a function of the concentrations of all solutes present. This is so complicated as to be impractical, and a simpler method must be found which is of acceptable accuracy. The Dunlap method, on the other hand. is too simple because it askmes that at any concentration the contrih-

Jan 1, 1967

By G. R. Fitterer

NONMETALLIC inclusions in steel have received much attention by metallurgists during the past few years. Many investigators have been emphatic in stating their belief that these impurities are the chief causes of steel failures, while others think that their effects are negligible. One of the main reasons that definite information on the effects of these impurities is lacking is that no reliable method has been developed for the exact determination of the amounts of these different impurities in steel. Some valuable new information has been brought out by a reliable method for nonmetallic inclusions which has been developed at the Pittsburgh Experiment Station of the U. S. Bureau of Mines, in cooperation with the Carnegie Institute of Technology and the Metallurgical Advisory Board. This procedure satisfactorily extracts some of the more common inclusions from steels, thus enabling the investigator to correlate steel failures with inclusion content. Although the data given herein are the first to be published on the subject of the electrolytic extraction method, the interest in the subject is evidenced by the fact that it is already being used by some 20 to 30 steel companies for their various purposes. Some of the comments received from these laboratories indicate that the method is highly satisfactory: the unfavorable comments, when traced to their sources, have been found to be based on some small mistake made in either installation or operation. The chief discrepancy seems to have occurred in attempts to apply the method to the extraction of inclusions from alloy steels. The procedure can be used only for the plain carbon steels and for such low alloy steels as those containing the usual amount of copper (0.2 to 0.3 per cent). Steels containing the carbide-forming alloys such as chromium, tungsten, etc., present far too many difficulties for the accurate determination of inclusions. Luckily, the iron and manganese carbides do not offer any difficulties and no contamination of the oxide-sulfide residue results. It is highly probable that some modification of the following

Jan 1, 1931

By Raja V. Ramani, Ralph W. Barbaro

This paper presents an application of a Mixed Integer Programming (MIP) model to the problem of locating a centralized coal preparation plant and determining the production schedule for the mines. The system used for illustrating model application is hypothetical but realistic. It consists of three mines, two potential preparation plant sites, heavy media processing plant, and one market. The goal is to maximize the total profit of the system while satisfying the coal delivery schedule over a three year period meeting both quantity and quality requirements (ash, sulfur, and heat content). In addition to the base case, four different scenarios are analyzed. These four modifications are: (1) removing the flotation circuit from the preparation plant and sending all of the fines directly to the clean coal, (2) lowering the quality of coal from one of the mines, (3) applying discounts to the unselected site to improve its competitive position, and (4) adding a new mine. A detailed discussion of the base case and the effect of these four alternatives is presented.

Jan 1, 1983

Organization Place Date International Mining Convention (Auspices, Van- 1919 couver Chamber of Mines) Vancouver, B. C. Jan. 8-10 American Institute of Consulting Engineers, Inc... New York, N. Y. Jan. 13 American Society of Civil Engineers New York, N. Y. Jan. 15-16 Institute of Chemical Engineers Chicago, 111. Jan. 15-18 American Wood Preservers Association St. Louis, Mo. Jan. 28-30 American Society of Heating and Ventilating Engineers New York, N. Y. Jan. 28-30 Automotive Engineers New York, N. Y. Feb. 4-6

Jan 1, 1919

By Stanley F. French, Bruno F. Koch

Although the amount of dust that will be actually recovered in the six main dust-control systems cannot be accurately stated until the tests mentioned previously are carried out, it is estimated that the average air entering the wet collectors will contain around 5 grains of dust particles per cubic foot. This means that the six systems handling a total of about 133,000 cu.ft. of air per minute will return about 68 1/2 tons of dust to the concentrator per day and since the copper in this dust will average around 2 per cent, the total recovery is approximately 1.37 tons of copper every 24 hours. This important copper recovery is not due entirely to the dust-control system since in a plant without control only the duct that is dispersed to the atmosphere represents a loss. A conservative estimate of the recovery of copper solely due to the dust control system would be about half of the total or approximately 0.70 tons of copper per day.

Jan 1, 1942

By H. E. Wheeler

THE work described was carried out during 1917 and 1918 at the testing laboratory of Watertown Arsenal at the instigation of the Nitrate Division and later with the concurrence of the Cannon Section of, the Ordnance Department, U. S. A. The experiments follow three principal lines of work: First, the effect of nitrogen under pressure on steel containers of various compositions at a red heat; second, the effect of decomposing ammonia on various alloy steels, iron, and non-ferrous alloys; third, a new theory of the erosion of guns in respect to the effect of nitrogen in steel. PART I In the Haber process for the manufacture of ammonia from its elements, it is necessary to have nitrogen and hydrogen of 1500 lb. per sq. in. (105.5 kg. per sq. cm.) at a temperature of 500 to 600° C. The steel containers for these gases gave trouble by failing without apparent cause. When the General Chemical Co. began to develop its method for the production of ammonia, it experienced the same difficulty and, knowing that the Haber process had solved the difficulty by the use of alloy steels, it made several small steel bottles of different compositions and kept them filled with these gases at this pressure and temperature until they failed. The time of service varied from a few days, for the plain steel casting, to two years for a chrome-vanadium forging. Four of these steel bottles were sent to this laboratory for investigation; they were a plain carbon-steel forging, a nickel-steel forging, a chrome-vanadium steel forging, and a chrome-steel forging. The time of service was as follows: plain carbon steel, 4 mo.; nickel steel, 6 mo.; chrome-vanadium steel, over 2 yr.; chrome steel, 4 mo. When these containers were cut open and the cross-section surface polished, they showed an inside zone with a different luster from the rest of the metal. Upon etching, this zone was almost unaffected while the rest of the steel etched normally.

Jan 4, 1920