Search Documents

By Reinhardt Thiessen

UNDER sulfur in coal, is usually understood that form of sulfur which is combined with iron and known as pyrite. It occurs in the form of halls, lenses, nodules, continuous layers, thin sheets, or flakes, both in horizontal planes and vertical cleavage fissures. But pyrites also occur as very fine microscopic particles, or nodules, disseminated through the compact coal. This form has had but very little consideration. Finally, there is sulfur in coal in an amicroscopic form (not visible with an ordinary microscope), probably combined with the organic matter that exists -in tile coal. This form has had considerable attention from a scientific standpoint, but has probably not been recognized enough on the economic side. One or the other, or both, of these two latter forms may comprise the larger part of the sulfur content of coal, especially after it has been washed or otherwise prepared for use.

Jan 9, 1919

By C. Schlumberger, M. Schlumberger

The object of this paper is to clarify the idea, so important when exploring by potential methods, of the depth of investigation attainable by electrical measurements. After defining, with some precision, .the term "depth of investigation'' in geophysics, the authors show how it is possible to regulate this depth in potential methods and to obtain an 'electrical drilling" from surface observations. They consider also the difficulties encountered in deep measurements and indicate how it is possible to reach greater depths than those having an industrial interest. Depth of Investigation The term, depth of investigation, in its general sense, is easily understood. For instance, a driller who can pull cores from a depth of 2000 m. is capable of working, with accuracy, to that depth. By means of a properly placed drill, he may locate an orebody at a depth of 1999 m., however small this orebody may be. On the contrary, the term as used in geophysics requires precise elaboration. As a matter of fact, no geophysical method, irrespective of the physical property studied (density, magnetic permeability, conductivity), can discover a very small body at a great depth because, in practice, the physical parameter upon which such a geophysical method is based is never regular enough, throughout the ground, to distinguish the feeble anomaly caused by the small, deep-lying body from the numerous anomalies due to irregularities of the encasing terrains. Aside from this question of the ratio between the size of the body being hunted for and its depth of burial, a second factor plays its role in the possible depth of investigation; that is the difference, for the parameter under consideration, between the body and its surrounding material. The greater this difference, and the more homogeneous the encasing terrains, the greater is the possible depth of investigation. This being generally established for all geophysical methods, it is possible to distinguish two main classes of these methods, from this same point of view

Jan 1, 1932

The Joint Economic Committee's subcommittee on international payments and exchange has recommended that, following international monetary reforms, the law which prohibits private possession of gold by American citizens be repealed. The subcommittee recommendation called for reforms to enhance the role of special drawing rights in international monetary affairs and downgrade the role of gold. Special drawing rights, also known as "paper gold", are on artificial reserve with the International Monetary Fund (IMF) which distributes them to member nations in proportion to their economic importance in the world economy. The special drawing rights are then used to settle debts between nations in the same manner as gold or currency. The subcommittee said that under the reforms now being discussed special drawing rights would be acceptable in lieu of gold among the member countries of the IMF.

Jan 1, 1973

By R. T. Southin

Cast ingots of 99.99 pct purity A1 and aluminum/copper alloys containing up to 2 pct Cu have been found to contain four zones rather than the three previously accepted, i.e., chill, colummar, and equiaxed zones. The fourth zone consists of a coarse dendritic layer across the top surface of the ingot which is open to the atmosphere. It is also found that the grains in the equiaxed region have a "cornet" shape, with a head which is coarsely dendritic and a tail which grew with the same structure as the columnar grains. Experiments using mechanical barriers, and others involving the elimination of the surface dendrile layer, have indicated that nucleation of the equiaxed zone is caused by the showering of dendritic particles from this surface dendrite layer. These particles are the dendritic heads found in the comet grains. A mechanism of nucleation and growth of these comet grains is put forward. Experiments with a number of other metals and alloys suggests that these conclusions may apply generally to ingots cast without the addition of nucleating agents, and solidified under normal conditions. THE macrostructure of cast ingots may contain the following three zones: i) a peripheral zone of fine equiaxed grains, commonly called the chill zone; ii) a zone of columnar grains extending inwards from the chill zone; iii) a central zone of equiaxed grains; these are normally larger than the chill grains. All three zones are not necessarily present in any particular ingot since their existence and magnitude depend upon the casting conditions and composition of the cast material. The mode of formation of zones i and ii is fairly well understood. However, the cause of the central equiaxed zone remains a matter of conjecture. Previous theories put forward to explain the mechanism of nucleation in the equiaxed zone have been examined by Chalmers1 and Winegard.2 At the time when the present work was carried out the most re -cent hypothesis was that due to Chalmers,1 who recognized more fully than previous workers that conditions in this zone during solidification were not conducive to nucleation. In his hypothesis, he suggested that nuclei were formed near the mould wall during the very early stages of solidification, and that they can drift into the central zone by convective motion. This was supported by evidence from experiments using mechanical barriers to stop the drift of nuclei. A similar hypothesis had previously been put forward by Genders.3 More recently, Jackson et al. 4 have observed that dendrite arms in organic compounds can melt off during solidification. They have postulated that this occurs in metals and alloys, and that the dendrite arms which have been freed from the main dendrite act as nuclei for the equiaxed zone. In the present work, critical metallographic examination has shown that there is a fourth zone in the macrostructure of cast ingots which is a dendritic layer over the top surface of the ingot. It is also shown that there is a relationship between this zone and nucleation of the equiaxed zone. EXPERIMENTAL DETAILS The alloys examined were prepared from super -purity aluminum of 99.99 pct min purity (spectro-graphically detected impurities of Cu, Fe, Si, and Mg) and copper of 99.98 pct min purity (spectrographically detected impurities of Si, Zn, As, Fe, Pb, Bi, Ni, Sn, Mn, Ag, Cr, and Al). Three compositions of ingots were examined, containing 0.0, 0.1, and 2 pct Cu, respectively. The alloys were melted in an alumina-lined salamander crucible using a medium-frequency electric induction furnace; when the appropriate casting temperature was reached, the alloys were cast without degassing or fluxing treatment. The mould used was made of electrode graphite and had the following dimensions: external diameter 6 in., height 9 in., with a mould cavity 8 in. deep and a diameter tapering from 5 in. at the top to 4 in. at the bottom. Casting temperatures used were generally in the order of 70" to 90°C above the liquidus and the mould was at room temperature before casting. Inserts kere placed in the mould cavity in some experiments. These consisted of either an 18-g stainless-steel tube of 2 in. diam held axially in the mould i in. off the bottom and extending 1 in. out of the top of the mould or a "trap-door" barrier of stainless-steel gauze of 24-mesh held horizontally in the mould 31/2 in. down from the top. The construction of this insert is shown in Fig. 1. All inserts were preheated prior to casting to prevent chilling. RESULTS The macrostructures of ingots of the three compositions are described, in terms of the three generally recognized zones, in Table I, and illustrated in Figs. 2(a) to (c). The most interesting observation in this table is that relating to the shape of the equiaxed grains, which were not in fact equiaxed but of almost tear-drop shape. Closer examination of these grains showed that each consisted of a head which had a coarse dendritic structure and a tail which always grew in the opposite direction to heat flow, and which had the same structure as that of the columnar material of the ingot concerned; i.e., in the pure aluminum and 0.1 pct Cu alloy it was cellular and in the 2 pct Cu alloy it was cellular-dendritic. Identification of original cast grains was greatly hampered in the super-purity aluminum ingots, and to a lesser degree in the 0.1 pct Cu alloy,

Jan 1, 1968

WITH the economic situation of the world what it is, we may expect important events in every month of 1922, and January showed us some-what of the nature of things that will happen. The Germans announced their inability to meet in full the reparation payments that were due Jan. 15. The Su-preme Council arranged a plan for them to pay some thing on account every 10 days, and called a conference at Cannes to talk things over. While this conference was in progress Premier Briand resigned and was suc-ceeded by Poincaré. This emphasized the growing differences between British and French policies and interests. The French want to exact the utmost from the Germans; so do the British. The latter think, however, that the French aims will so cripple the Germans that they can not work properly and hence can not trade. Great Britain, with a huge unemploy-ment problem, must have trade. The French thought that Briand was unduly deferring to the British and withdrew their support of him. The other important political developments of the month in Europe were the establishment of the Irish Free State, relieving the British of the vexatious Irish question; and the growing tendency to recognize the Soviet government of Russia and admit its representa-tives into international conferences. In the United States the great political event was the establishment of the dominance of the agricultural bloc in the Senate, which implies the passage of agrarian legislation that will probably be unwise. Economically, there was no progress in the United States. If anything there was probably some reces-sion in the physical volume of business. There were some further reductions of wages, but these were irregular, geographically, and moderate in amount. The great unionized trades maintained the jam. Events of great importance were the formal demand of the anthracite coal miners for increased wages on April 1 and the declaration of the bituminous coal miners that they would resist a reduction at that time. The attitude of these groups is believed to presage labor troubles in the spring. In the metal markets affairs were dull during Janu-ary, but prices were generally firm, save for a little further weakening in iron and steel. In the matter of production, however, there was some quickening of activity, especially in copper, zinc and iron.

Jan 2, 1922

By W. C. PAGE

ALL mine ore here must be concentrated before shipment, which involves selective flotation. Three products are made: lead, zinc, and pyrite concentrates. The equipment and practice are so well outlined in the accompanying flow sheet that only a few amplifying remarks are necessary. After crushing at the mine to approximately 4 in., the ore is carried by aerial tram about 4 1/2, mi. to the mill. From 1800 to 2000 metric tons per day, excluding Sundays, is thus transported. At the mill, the buckets are hand-tipped into the bins. After crushing to pass a ¼ -in. square opening, the ore may be stored in reserve crushed-ore bins or ball-mill feed bins as desired. Total bin capacity at the mill is about 4000 metric tons. The concentrator is arranged in three independent grinding sections, each fed from its own storage bin. Grinding operations follow standard practice, with ball mills in single-stage closed circuit with classifiers, the overflow from which is delivered to the lead circuit rougher flotation machines,

Jan 1, 1936

By T. Egleston

THE works of the Ore Knob Copper Company are situated in the county of Ashe in the northwestern part of the State of North Carolina, about ten miles from the Virginia line, at an elevation of 4600 feet above the sea. The nearest railroad station is at Marion, Smythe County, Virginia, about forty-five miles distant. The roads from the railroad to the works have been constructed by the company for the transportation of their material, and are very hilly, and in certain seasons of the year in bad repair. Transportation is therefore always limited and never easy, although it is done by contract at a very low price. The main difficulty with the transportation is not so much its cost as the fact that it puts a limit to the production of the works. These unfavorable conditions make it necessary for the owners of the mine to smelt their ores and to send to market nothing except the metal, which alone will bear the cost of transportation. The mine was opened previous to 1860, but has only been worked systematically during the last five or six years. The vein is a fissure vein from ten to twenty feet in thickness in the gneiss of the

Jan 1, 1882

By T. Egleston

The works of the Ore Knob Copper Company are situated in the county of Ashe in the northwestern part of the State of North Carolina, about ten miles from the Virginia line, at an elevation of 4600 feet above the sea. The nearest railroad station is at Marion, Smythe County, Virginia, about forty-five miles distant. The roads from the railroad to the works have been constructed by the company for the transportation of their material, and are very hilly, and in certain seasons of the year in bad repair. Transportation is therefore always limited and never easy, although it is done by contract at a very low price. The main difficulty with the transportation is not so much its cost as the fact that it puts a limit to the production of the works. These unfavorable conditions make it necessary for the owners of the mine to smelt their ores and to send to market nothing except the metal, which alone will bear the cost of transportation. The mine was opened previous to 1860, but has only been worked systematically during the last five or six years. The vein is a fissure vein from ten to twenty feet in thickness in the gneiss of the

Jan 1, 1882

By H. R. Spedden, A. M. Gaudin, M. P. Corriveau

A preliminary study of silver ion adsorption by sphalerite in ion exchange column with influent electrolyte marked with radiosilver is described. Rapid ion exchange occurs at first followed by slow reaction controlled perhaps by solid state diffusion. One experiment with radiocopper instead of radiosilver is reported briefly. IT has been known for many years that sphalerite is floated after it has been activated by a metallic cation, particularly copper.' The activation of sphalerite by copper is known to be an exchange of an atom of copper for an atom of zinc at the surface of the sphalerite.2,3 It has been estimated from various guesses of the available mineral surface that the depth of the copper-bearing coating is of the order of thickness of one atom. However, the exact mechanism of the activation process is unknown. A number of metals other than copper act in the same general manner."' " In particular, it has been known that silver replaces zinc at the surface of sphalerite. As copper is usually divalent, whereas silver is monovalent, it may well be assumed that there are differences, perhaps major differences, in the detailed scheme of activation by these two cations. Furthermore, since silver has unusual photoelectric properties and may be a contributor to the fluorescence of sphalerite, a study of its activating mechanism might open up some interesting avenues for exploring these other phenomena. The choice of silver as an activator of sphalerite was suggested also by the fact that its radioactive tracer, silver 110, is particularly convenient in that it has a long half-life and is energetic enough to permit counting through a counter window. The experimental technique selected, therefore, included the preparation of solutions of silver nitrate con- taining a proportion of active silver nitrate sufficient to give convenient counting data. In further considering the method to be used, a desirable choice seemed the use of batch experimentation in which a given solution was allowed to act on a certain lot of mineral for a given length of time at a given temperature, this period of mutual reaction being followed by analyses of the separated solid and solution. But an alternative method seemed more attractive. This is the method now so familiar to the users of ion-exchange resins, which was first made famous by the Russian chromatographer, Tswett.6-8 It consists in forming the mineral into a porous column through which the solution is allowed to flow at a constant rate. The usual method of allowing a batch of solid to react with solution is the equivalent of a single plate distillation operation while the chromatographic or ion-exchange column is a multiple-plate method—the multiplicity of the plates being represented by the reciprocal of the rate of flow of solution through the column. It seemed to us that the chromatographic method had such

Jan 1, 1952

By H. J. Levinstein, H. J. Guggenheim

RbFeF3 is a transparent ferromagnet with a large faraday rotation which permits the direct observation of magnetic domain structures in bulk crystals. If the position of dislocations within the crystal were known a study of domain wall dislocation interactions would be possible. In this paper an etch pitting solution is described which gives a one-one correspondent between the etch pits and the dislocations intersecting the (100) surfaces of RbFeF3 crystals. In addition, RbFeF3 is shown to have sufficient plasticity so that known arrays of dislocaticms can be put into the crystal. It is concluded that RbFeF, is an ideal material for the investigation of domain wall dislocation interactions. THE influence of lattice defects on the motion of domain walls in ferromagnetic materials has been studied extensively both theoretically and experimentally.4 The experimental data obtained has been qualitative in nature due to the lack either of a quantitative knowledge of the magnetic domain array in the material or of the nature of the dislocation configuration in the material. At room temperature RbFeFJ has the cubic perovskite structure. It is ferromagnetic below 86°K.5,6 It is also transparent and has a large faraday rotation in the magnetic state.7 The domain structure of this material is observable in three dimensions in crystals which are millimeters in thickness.' Since RbFeF3 satisfies the requirements of having an easily visible three-dimensional magnetic domain structure, it was of interest to determine if the dislocation structure of the material could be determined and if the material was sufficiently plastic so that dislocations could be introduced into the as grown crystals. This is a report of the results of that investigation. EXPERIMENTAL PROCEDURE The crystals of RbFeFs used in this experiment were grown by a technique described elsewhere.5 In order to obtain flat strain-free surfaces, the samples were first cut to the crystal orientation desired and the surfaces were polished by employing standard metallographic techniques. The samples were then immersed in a solution of 1 to 3 g of KOH in 100 ml of water. This solution removes the damaged surface layers uniformly leaving a film on the surface of the sample. Etch pits are obtained by immersing the sample in an approximately 50-50 solution of 30 pct peroxide and concentrated acetic acid. The film formed during the KOH treatment turns deep red in color in the etching solution and flakes off the sample. The etching time required depends upon the pit size desired and

Jan 1, 1970

By R. A. Falconer, H. L. Lovell

With increasing requirements for fine coal cleaning and the many advantages of the cyclone operating on a coal-water slurry, a series of studies designed to achieve an enhanced understanding of the cyclone parameters has been pursued. The purpose of this investigation has been to vary a series of dimensional parameters with an experimental 15-in. diam hydro-cyclone, and to determine the relative effects of parameter variations upon ash and sulfur removal. This study of the hydrocyclone is a continuation of a series of investigations, conducted in the Dept. of Mineral preparation at The Pennsylvania State University, which are directed toward the removal of ash and sulfur constituents from fine bituminous coal by size-density separations in cyclones, and toward a fuller understanding of the complex mechanisms involved in such separations. The purpose of this investigation has been to vary a series of dimensional parameters with an experimental 15-in. diam hydrocyclone, and to determine the relative effects of parameter variations upon ash and sulfur removal. Of special interest was the response to cone angle variation, since it is the high included cone angle that generally distinguishes the hydrocyclone as a gravity separator rather than a classifier. DESCRIPTION OF THE HYDROCYCLONE Fig. 1 is a dimensional drawing of the hydrocyclone used in the investigation. The unit was designed and fabricated by Heyl and Patterson, Inc., for experimental use. The dimensional parameters considered were: 1) Three cone sections having included angles of 45, 60, and 95,degrees, 2) Three 3 1/8 in. diam vortex finders having lengths of 15, 17, and 19 1/2 in., 3) Three 4 1/16 in. diam vortex finders having lengths of 15, 17, and 19 1/2 in. 4) Two apex sections having diameters of 2 and 2 1/4 in. The feed inlet orifice had a fixed diameter of 3 in. The hydrocyclone test installation was made at The Pennsylvania State University pilot plant at Barnes-boro, Pa., which operated at 50 tph. During the period that the hydrocyclone was tested, research was in progress at the Barnesboro site to reprocess refuse material from a near-by coal preparation plant in

Jan 1, 1968

By J. J. Pye, J. B. Drew

The surface-diffusion coefficients of Ni63 diffusing on low-index planes of nickel single crystals have been measured over the temperature range from 400° to 1000°C using a precision autoradio-gvaphic technique. The activation energy for sur -face diffusion appears to he the same on the {111}, {110), and (100) planes and amounts to -0.60 ev. This is in good agreement with the value (-0.62 ev) reported for (111) planes obtained by mass-transport techniques. In an earlier paper, the authors have reported self surface-diffusion coefficients on silver.' In that work, a deviation of the diffusion coefficients from linearity in the Arrhenius plot was observed at high temperatures. This effect was attributed to a loss of tracer atoms into the bulk by volume diffusion. The purpose of the present work was to extend the technique developed to the nickel surface-diffusion system up to the point where volume diffusion would come into play. The nickel system especially lends itself to this technique due to the high efficiency of the isotope in darkening the film and the large absorption of the weak radiation (0.063 mev /3- particle of the trapped tracer atoms. The diffusion coefficients and ictivation energy for different orientations on nickel can also be compared with a report published by Blakely and Mykura 2 where a mass-transfer technique was used. This paper reports the self surface diffusion of nickel on the low-index planes over a wide temperature range using a precision autoradiographic technique. EXPERIMENTAL PROCEDURE The experiment is similar to that described in the earlier publication consisting of a radioactive needle as a source resting on a flat, smooth, chemically polished surface annealed in a dynamic dry-hydrogen atmosphere. The needle is held snugly on the surface by a holder fabricated from commercially pure nickel. The point source is made by grinding down a small-diameter nickel rod until a tip of approximately 0.1 mm radius is formed. It is then etched and the needle tip plated with the radioactive isotope Ni63. Nickel single crystals were used whose main impurities were spectrographically determined as Co 0.05, Fe 0.007, C 0.005, and S 0.003 pct. The surfaces, oriented to within 1/2 deg of the low-index planes, were carefully mechanically polished and etched in a 50-30-10-10 hot solution of acetic, nitric, sulfuric, and phosphoric acids giving a smooth polished surface. The crystals were then washed in distilled water and alcohol. Annealing temperatures ranged from 400° to 1000°C with a furnace arrangement in which the crystals could be brought up to temperature in times short compared to diffusing times. The temperature was maintained constant to ±10°C. In the temperature range investigated, the ratio of the surface-diffusion coefficient to the volume-diffusion coefficient (Ds/Du) was 105 or more and the mean bulk-penetration values, calculated from literature values of volume-diffusion coefficients,3 were on the order of 10-5 cm. After the diffusion anneal, the sintered needle is removed, and both the radius of the needle point and spot left on the crystal face are measured. The crystal is then placed on photographic film. Diffusion profiles are obtained by scanning the film with a recording microdensitometer which has a slit width of 10µ. DISCUSSION AND RESULTS The experimental conditions are such that the source strength and needle radius are essentially constant and the time is adjusted such that the mean bulk penetration is small. An exactly analogous heat-flow problem has been considered by Carslaw and Jaeger4 and the solution can be written in integral form as:

Jan 1, 1964

E. E. THUM,* Salt Lake City, Utah (written discussion?).-While the present paper is confined exclusively to the microstructure of fusion welds, it may be of interest to draw attention to certain appearances existing in resistance welds such as spot or butt-welded joints produced by the Thomson process. For instance, a butt weld between two pieces of carbon tool steel (carbon about 0.90 per cent.) will show concentric ellipsoids of the various materials from pearlite to martensite. The surfaces of demarcation are quite well defined, the center of the ellipsoid being at the intersection of the axis of the piece and the plane of the weld. Often these unannealed welds show a troostitic center; evidently this core was not quenched as rapidly as the surrounding shell. Such specimens are beautiful samples for instruction purposes. An annealed butt weld of this kind will show a very well defined central ellipsoid of decarburized, materials. It is interesting to consider the reason why this change takes place. It must be understood that the heat is on the metal for a very short time, possibly 30 sec. It is therefore evident that the decarburization, or migration, of the carbon takes place with extreme rapidity. Since no blowholes are evident in a well-made butt weld, the deoxidizing air and the products of combustion must migrate with the highest speed; second, the carbon might migrate back into the stock; or, last, a large proportion of the pearlite may be extruded with the hot metal, which forms a fin at the plane of weld. Examining these possibilities in detail, it is not probable that such deep-seated decarburization, extending with maximum effect to the very center of a 2-in. round bar, is done by reaction with the oxygen of the air. This would postulate entrance of oxygen and egress of carbon oxides in large quantity without leaving behind traces in the form of oxides or

Jan 5, 1919

By Claudia Gasparrini

Silver occurs in nature in major, minor and variable amounts in a very large variety of minerals and in several mineral species in the same ore. Because these minerals may respond differently to the same flotation or leaching agents, detailed studies to establish the correct silver mineralogy become essential for optimum recoveries in those situations where the silver is treated as a primary product. On the other hand, fine grain sizes, which often affect gold recoveries, are not generally as critical in silver metallurgy, due to the lower market price which allows for more of the element to remain In the tailings before incurring in economical losses.

Jan 1, 1984

By Charles F. Brush

THE compression of gases to a very high degree, for purposes of scientific research, has long presented serious difficulties to the physicist. Great advances have been made of late years in the construction of ordinary air or exhaust pumps, while very little has been done towards the improvement of compression pumps. The principal difficulties encountered in the construction of such apparatus are the existence of the so-called "dead space" in the pump barrels, leakage of the piston packings under high pressure, and the trouble arising from the unequal expansion of parts caused by the development of the latent heat of the gas during compression. Of these obstacles to success, the "dead space" is far the most serious, as it fixes a limit to the performance of the pump beyond which it is impossible to carry the compression. The writer having occasion, some time since, to make a series of investigations on gases very highly compressed, and finding no apparatus, or description of apparatus, adequate to produce the required

Jan 1, 1876

By Glenn C. Waterman

THE diamond drill is a very important tool in exploration and development testing and its use is increasing. In almost all cases results of diamond drilling are analyzed on the basis of grade and tons. A proper evaluation of core and sludge assays is important if drilling results are to be acceptable as a basis for geologic and engineering appraisal. The relatively wide variation in assay averages as calculated by various well-known combining methods indicates that the engineering choice of a method may affect the outcome of the drilling in terms of ore and waste. The problem of combining assay results from core and sludge samples has been discussed many times in conference and in the literature.'" Most writers agree that the field of disagreement in methods is large and that the engineer on the job must consider features unique to his drilling, pick one of several combining methods, and depart from the rules when abnormal results come in. All the discussion to date can be summed up by the admission that as yet there is no fairly simple, generally acceptable combining method that is practicable over a wide range of drilling conditions, ground conditions, and ore occurrence.

Jan 1, 1955

By Robert H. Hafner, Irvin R. Kramer, Stewart L. Toleman

IN his paper on the calculation of hardenability from chemical composition, Grossmann1 discussed the effect of most of the alloying elements used commercially. The purpose of the work reported in this paper was to determine the effect of several other elements on hardenability-arsenic, antimony, beryllium, cobalt, columbium, germanium, tellurium, tin, aluminum, and titanium-and to extend the range of composition of some of the elements studied by , Grossmann-chromium, copper, manganese, molybdenum, nickel and silicon. EXPERIMENTAL METHODS To determine the effect on hardenability, suitable amounts of the alloying elements were added to experimental heats and the hardenability determined by means of end-quenched hardenability specimens. The steels were melted in a high-frequency induction furnace with a basic crucible, using ingot iron as a base for some of the heats and S.A.E. 1015 for others. The alloying additions were made as ferroalloys or as metal, depending on the ' alloying element. Hundred-pound heats were split and poured into square, tapered, cast-iron ingot molds with hot tops. Aluminum was not used as a deoxidizer in most of the heats. The ingots were homogenized for 12 hr. at 1260°C. (2300°F.) , and forged into rounds of 1 ½ in. diameter. These bars were normalized twice from 840°C. (1550°F.) before machining into Jominy bars. The composition of the steels was deter- [ ] mined in most cases by samples taken from the end-quench hardenability specimen. As suggested by crafts,2acid-soluble

Jan 1, 1943

By F. Forward, H. Veltman, A. Vizsolyi

Activities of oxides in the ternary FeO-MnO-SiO system are calculated from data on the binaries, using the Gibbs -Schuhmann method. These activity data are used, together with thermodynamic relations, to calculate the contents of oxygen, silicon, and manganese in liquid iron, and the composition of the corresponding oxide phases in equilibrium with it. Excellent agreement was found between calculated and experimental metal compositions, indicating that thermodynamic methods, such as those presented, can supply useful data on slag-metal equilibria, and are therefore capable of wider application. When molten steel containing oxygen is treated with a deoxidizer, the product of the reaction is composed of the oxides of the deoxidizing elements together with more or less iron oxide. This assemblage of oxides is presumably very close to equilibrium with the melt since it is formed directly from elements dissolved in it. Therefore, it is likely that metal analyses corresponding to a given oxide phase composition are calculable with considerable precision where sufficient information is available on activities in both phases. The present study was made to test this hypothesis in the case of deoxidation by silicon and manganese. Here experimental data on the relationship among oxygen, silicon, and manganese in the metal phase are available, as are activity data for the MnO-SiO2, FeO-SiO2, and FeO-MnO binary systems. A further objective was to demonstrate in a specific example how gaps in the data may be filled by judicious interpolation, and how the Gibbs-Schuhmann method is applied to obtain activities in ternary systems. The rigorous derivation of the latter, requiring considerable facility in handling partial differential equations, tends to mask the real simplicity of the method, and repel the very engineers and experimenters who would benefit the most from its use. I) GENERAL PROCEDURE Deoxidation of steel with silicon and manganese results in the formation of two phases, metal and oxide. The number of components is four—Fe, Mn, Si, and 0. The phase rule then gives the number of degrees of freedom: If temperature and pressure are fixed, 2 deg of freedom remain. Consequently, it suffices to fix the concentration of two of the components of the system for all the concentrations to be determined and, at least in principle, calculable. The practical problem is then to discover a straightforward method of calculation with a minimum of trial and error solutions. The type of reactions to be dealt with are like the following: Si (in steel) + 2 O(in steel) = SiO2(in oxide phase) The standard free energy of this reaction is readily obtained from the literature, so that the equilibrium constant can be calculated by the expression: Since the metallurgist is concerned with percentages rather than activities, a real solution requires information that will permit activities to be converted to concentrations. This information is fairly adequate for the elements dissolved in molten steel, but is not available for the FeO-MnO-SiO2 oxide system. Therefore, the first step in this study was to find the relation between activity and concentration for the three oxides making up the system. The next step was the calculation of slag and metal compositions that are in equilibrium with one another. As shown by the phase rule, it is sufficient to assume the values of two composition variables in order to calculate the rest. But which two are picked makes a vast difference in how difficult the calculation turns out to be, so that it is necessary to make preliminary trial of several routes to find the easiest one. A convenient method is to begin with the slag, and to pick FeO concentration and that of one of the other oxides. Starting with the relation between oxygen dissolved in the liquid steel and FeO in the slag permits a good first estimate to be made of the oxygen content of the steel in equilibrium with FeO, because the iron content being fairly close to 100 pct, Fe has an activity close to unity. Using this first estimate of oxygen activity, approximate values of the manganese and silicon contents of the melt are readily calculated from the appropriate equilibrium constants. A minor correction for the depar-

Jan 1, 1963

By G. S. Ansell, J. Weertman

The creep behavior of an aluminum alloy hardened with a finely dispersed phase of aluminum oxide was investigated. The as-extruded alloy shows an approximate steady-state creep in which the creed rate depends exponentially on the applied stress. The activation energy of creeb is abbroximately 150,000 cal per mole. The recrystallized alloy shows no steady-state creep. ONE method of improving the creep resistance of a metal is to introduce a finely dispersed second phase into the metal matrix. The improvement of the creep resistance has been qualitatively explained by assuming that the dispersed second-phase particles act as obstacles to dislocation motion. If the main effect of second-phase particles is simply to hinder dislocation motion then it is possible to derive a high-temperature creep equation for a dispersion-hardened alloy in a straightforward manner. In the Appendix of this paper such an equation is derived from a creep model which works very well for pure metals. Recently, F. V. Lenel has fabricated, for the first time, powder extrusions of aluminum-aluminum oxide in a large-grained recrystallized form. This alloy, designated as MD 2100, consists of a fine dispersion of aluminum oxide plates in a matrix of commercial purity aluminum. A considerable amount of investigation has been carried out concerning the microstructure and physical properties of this alloy.&apos; ) The aluminum oxide is present in the form of flakes 130A units thick and 0.3 u on edge. They are dispersed in the aluminum matrix with an average spacing of approximately 0.5 jx. The spacing varies in the range of 0.05 to 1.5 µ. The alloy structure is extremely stable at high temperatures. For this reason the alloy offers a unique opportunity for a fundamental study of creep of a very finely dispersed two-phase alloy. Lenel supplied specimens in both the unrecrystallized and recrystallized condition. This paper reports high-temperature creep experiments carried out on these specimens. The results obtained were rather unexpected. No steady-state creep was observed in the recrys-tallized material. In fact, after some transient creep which takes place upon loading, the creep rate is essentially zero ( < 10-8per min). If the second-phase particles acted solely as obstacles to the motion of dislocations, measurable steady-state creep would be expected. Since none is observed it appears that the main effect of the fine dispersion in the recrystallized material is to inactivate the dislocation sources themselves, rather than hinder the motion of dislocation loops created at these sources. EXPERIMENTAL DETAILS Specimens were tested in wire form, 0.087 in. in diam for the as-extruded alloy, and 0.035 in. in diam for the recrystallized alloy. These samples were held in friction-type wire grips; a gage length of 2.5 cm was used for all the creep tests. The specimens were held at 600°C in the test apparatus for at least 15 hr prior to each test. The tests were run under the condition of constant loading and, since the creep strains were small, can be considered as constant stress tests. The temperature of testing was held constant within 3°C. Elongations were measured with an optical cathetometer which was capable of measuring strains as smaIl as 0.00012. This allowed the measurement of strain rates as low as l0-8&apos;per rnin. In addition to the creep tests optical micrographs were made in order to determine both the grain size and microstructure of these materials. RESULTS Fig. 1 shows a few typical creep curves obtained from the as-extruded material. The elongations were somewhat erratic, but each curve shows a region of quasi-steady-state creep from which an approximate steady-state creep rate can be obtained. In general the higher the stress at a given temperature, the greater the total elongation before fracture. The lower the applied stress, the longer is the region where the creep rate is almost constant. Summary data from the creep tests of the as-extruded material are listed in Table I. The steady-state creep data of the as-extruded material for a range of stresses at a constant temperature follow a creep equation of the type creep rate = K&apos; = A exp (&) [11 where A and B are constants, k is Boltzmann&apos;s constant, T is the absolute temperature, and a the stress. The standard error of estimate of the data received is less than one order of magnitude. As shown in Fig. 2, if one compensates the creep-rate data for the effect of temperature over the range of test temperature, the steady-state creep data roughly follow a creep equation of the type Temperature compensated creep rate = K* = A exp

Jan 1, 1960

By P. D. Frost, H. A. Robinson, J. R. Doig, M. W. Mote

The mechanism of hardening in heat-treatable zirconium alloys was foUNd to be analogous to that for titanium alloys. Zirconium containing a relatively large addition of a ß -stabilizing element such as molybdenum or columbium can be hardened by the following transformation: Lean alloys, having insufficient alloy content to retain ß at room temperature are hardened by the following transformation: Application of these findings in Zr-Mo-Sn and Zr-Nb-Sn alloys produced strengths as high as 190,000 psi with reasonable ductility. PRIOR research on zirconium alloys has been concerned with development of greater strengths and creep resistance by solid-solution hardening or by dispersion hardening. Although solution and aging heat treatments had been applied earlier to zirconium alloys, quenching frequently produced low ductility. The possibility that the ß-to-w transformation, discovered earlier in titanium alloys,&apos; might also occur in zirconium alloys and cause low ductility was considered, and, indeed, was found as predicted2 to be the case. In the earliest experiments, the heat-treatment response of titanium, too, was disappointing. However, by avoiding the formation of the embrittling w phase, it became practical to obtain room-temperature strengths higher than 180,000 psi, with elongation values of 10 pct.3 Based on the present concept of titanium heat treatment, the principal requirement for a heat-treatable zirconium alloy is that it contains a certain minimum amount of one or more ß -stabilizing elements. Only molybdenum, columbium, and tantalum, when present in sufficient amounts, are known to stabilize ß zirconium to room temperature during rapid cooling from the ß field. Tantalum was undesirable because of its high thermal-neutron cross section. Aluminum and tin are effective a stabilizers, but aluminum has been shown to seriously decrease the corrosion resistance of simple zirconium alloys in hot water. Therefore, for the present study, tin was used as the stabilizer addition. The alloys selected for this evaluation are presented in Table 1 along with their analyses and ß-transus temperatures. The analyses indicated that intended compositions were usually realized. EXPERIMENTAL PROCEDURES All of the alloys were melted from sponge zirconium and fabricated to sheet for heat treatment

Jan 1, 1960