Search Documents

By AIME AIME

TRANSFER to the Bureau of Mines of the responsibility for conservation and production of helium, and announcement that a proposal has been made to the President for commercial operation of the Los Angeles has attracted new attention to the helium program of the Government. The matter is one in which mining engineers, and the mining industry in general, have a peculiar interest. Helium is a byproduct of the petroleum and natural gas industry. It is found in certain of the natural gases which have themselves been discovered, in the main, in the search for oil. If it is to be produced on a large scale, the conservation and development of the fields will necessarily be done by the men of the oil and gas industry. There is no known or expected source of supply of quantities of commercial importance save in the natural gas fields. Not all gas wells supply helium and none of them supply it in important percentages. If it were necessary to prospect a field, develop it, lay pipe lines and build production plants for the helium alone, the cost would be prohibitive. On that basis helium would necessarily be restricted to essential war uses, where cost is subordinate to need. As a byproduct of the natural gas in certain, at least, of the fields in the United States there is distinct reason for anticipating that it may be produced in amounts and at a cost that will permit its regular use in commercial airships.

Jan 1, 1925

By Herbert Hoover

DURING the year, the' Institute has made the most remarkable growth in its history. Our actual increase in membership was 1816 and therefore was 80 per cent. larger than any previous year. Even without expectation of any abnormal growth, we should pass in the year 1921 the 10;000 mark. The causes of this increased growth are not far to seek.. They lie in the widening vision of the Institute's work, not only in its relation to' the profession but as an avenue of service to the nation as a whole. The Institute is today in the first rank of influence among public institutions in the country. During this year we have, for the first time in many years, had a ?deficit of some $3000 in our finances. The sum is not important, but it- does indicate the tendency of the times, and that is the high cost of living:' The increase in our expenses lay, to the largest degree, on the publishing side of the Institute's work. If we compare the year 1918, as a fairly repre¬sentative year, with that of 1920, we find that the costs of issuing the' Institute's publications, after deducting the income received from these publications, shows a .net increase of about $33,000. for the year. This has been to some degree due to the enlarged membership but to a large degree due to the cost of the paper and printing.

Jan 1, 1921

By AIME AIME

AT the annual .meeting of the Minnesota Section in December, Dr. Leith characterized as a question still open the exact method of origin of Lake Superior iron ores and emphasized it as an important practical problem for the future. He welcomed the step taken last year by Dr. Gruner in presenting a new hypothesis, and asked Lake Superior geologists to meet the challenge of such multiple hypotheses by unbiased, study.

Jan 1, 1932

By AIME AIME

L H. DUSCHAK gave an interesting talk at a recent meeting of the. San Francisco Section, based -011 experimental work with a variety of ores at the laborator of the Treadwell-Yukon Co., in Berkeley, Cal. He was of the opinion that the customary "cut and try" method of flotation testing was still in evidence and that the flotation process was more of an art than an exact science. Propounded theories have enabled investigators to' classify reagents as well as to suggest new ideas both in the metallic and nonmetallic fields, but the application of theory has riot as yet been able to solve many of the unknown factors in operation.

Jan 1, 1932

By K. Leutwyler, H. L. Bigelow

Jan 1, 1966

By Oliver Bowles

ROCK is no doubt the most abundant of all material things because the planet on which we live is made of it. All animal and vegetable organisms and the multitude of natural and manufactured products that occupy a comparatively insignificant film on the outer surface of the planet are derived from rock. Processes of Nature acting for untold centuries have transformed rock into soil, making possible the development of vegetable and annual life; and rocks have supplied the numerous raw materials, metallic and nonmetallic, wherewith the innumerable appurtenances of a complex civilization have been fabricated. As time goes on we live with increasing speed and with enlarged desires. Time and space are shortened by man's ingenuity, and products for human use must be manufactured with greater and greater celerity. It was inevitable that Nature's slow processes of rock alteration should fail to keep pace with human demands and that the variety of natural products should fall far short of the requirements of an industrial age. Man therefore supplemented these processes by attacking rock in its native bed amid using it to supply needs not otherwise satisfied.

Jan 1, 1934

By R. W. Raymond

I wish to call the attention of the Institute to a curious subject, brought to my notice last summer by Mr. Begger, the accomplished metallurgist of the smelting-works of the Boston and Colorado Company at Black Hawk, near Central City, Colorado. At these works, the richest auriferous sulphurets of Colorado (particularly copper pyrites) are smelted in reverberatories, together with roasted tailings (iron pyrites), and the gold and silver are concentrated into a new, artificial sulphide, or copper matte, containing $1500 and upwards of the precious metals per ton, and this is shipped to Swansea. I will say in passing, that this shipment of an unrefined product, like the similar shipments from Utah and Nevada to San Francisco, Chicago, St. Louis, Newark, New York, and Europe, of crnde argentiferous lead or "base bullion," is not a sign of incomplete metallurgy here, but has a sound business reason. The separation of the precious metals in the West would be more expensive, to begin with ; and then it would necessitate the movement of these metals by express, . - at high rates and risk, to commercial centres or coining mints, while the base metals having no home market, must be shipped and sold at little or no profit. At present, the gold and silver, safely packed, as it were, in the base metals, are transported with safety as ordinary freight; and the base metals probably more than pay cost of shipment and separation. To return to the Black Hawk reverberatories. On a recent occa-

By T. Egleston

The materials containing copper which are refined in the United Statrs, are, for the most part, the natiye noppers of Lake Superior. IJntil quite recently but little pig copper Was made for sale, and that came principally from the pure sulphorous ores of New England and the Sonth, and was generally sdd to reSneries not far from the ore filrnaceu. A stnall aiuoiint found its way into the'niarket which was produced either as the by-product of the treatment of gold and silver ores, or as the result of the treatment of impure copper ores; but both these grades, on account of the impurities they contained, were loolced on with stlspicion, and were not sought for. A11 the grtlGis of pig coppcr are sold by the unit of oopper contents, a great redtiction being made in the price when impurities are present. There are at the present time only three works which treat native copper, the two of the Detroit and Lake Superior copper Company, and the works of C:G. Hussey & Co., in Pittsburgh. There are a few works ivhich smelt sulphuroris ores and refine their pig; bo sides these t1le1-e arc a few siuall works where gig copper is refined uuly. Some of these purcIlase blscir copper, refine scrap, or simply refine such grades of ingot copper as are found in the market, but nlostly that from Lake Superior, for the purpose of getting it into swh shapes that can be handled cpmtriercially to advantage, such as in making large plates or high grades of wire fir electrical purposes. A nomher of such works are situated in the Xaugaturk Vatley aud elsewhcre in New England. The recent discoveryof vnlt~sblc ores in Ariarona makm it probable that within a few year8 the refining of capper In the United States will make great develupments. Up to the time of the discovery of the mines on Lake Superior, only a very small quantity of native copper had ever been foond, not sufficient to justify the erection of worlrs fbr its special treatment. It had, besides, never been found in very large maweq so that the discovery of greabblocks of it presented serious difficulties, not oolp in mining it,-I- but in bringing it into a merchantable condit'ion. It seemed a very simple process to melt these large maws,

Jan 1, 1881

By H. David Swain

On Bougainville Island in Papua New Guinea, Bougainville Copper Ltd. (BCL) has successfully applied electronic data processing (EDP) techniques to pit operations and mine planning. Though the EDP program is not complete, BCL has realized significant improvements in short and long range mine planning, and equipment and manpower utilization. About 80% of BCL's 4000 employees are Papua New Guinea nationals, and most have little education or training. The operational characteristics of the computer equipment, however, have been quickly adapted by users with low educational standards.

Jan 3, 1979

By T. A. Rickard

The key-note of good writing, as of good manners, is B natural. Sincerity is the first requisite for effective writing. When a man says what he knows or believes, he is likely to be interesting, because each human being possesses an individuality, a point of view, or a range of sympathy that makes him different from his fellows. To say or to write what you do no6 think, for the mere sake of talking or writing, is a verbal exercise that must be performed with extraordinary skill if it is to be attractive. Affectations are rarely attractive, rarely effective. To be natural is to be yourself, not a poseur; to give the reader the best of yourself, instead of re-warming the baked meats of yesterday. Quotations-which are second-hand thoughts-will serve occasionally when the thing you want to say has been said so well by another that it would be waste of energy to try to say it better; but, as a rule, the utterance of the writer himself is more interesting than the quotation, because the writer brings something of himself to bear on the subject, and for the moment is more in touch with the reader than any dear departed author. Therefore, say things as best you can in your own way, neither in borrowed words nor in the phraseology that mimics another. Write as if you were speaking to a person whom you desire to persuade or convince. You will then write better than you speak, because, in the first place, you can be more deliberate, and, secondly, you can revise what you have written. Speaking and writing are similar mental acts, with a difference: the difference between eating food raw and eating it cooked. Some kinds of food gain nothing by being cooked; likewise some kinds of utterance are not bettered by being written down first; but most expressions of thought, especially

Jan 1, 1931

By George I. Adams

PHYSICAL AND CLIMATIC DIVISIONS. PERU is divided into three regions-the coast, the sierra, or high mountainous region, and the a montana," or forest region of the Amazon basin. The Coast.-The coast is an arid region. No rain falls excepting in the extreme northern part, which borders the Gulf of Guayaquil. There is, however, a slight precipitation in the form of mist (garua), which occurs on the coast hills during the so-called winter months. The aridity of the coast is due principally to the antarctic or Humboldt ocean-current, which, being cold and having a temperature lower than that of the land, absorbs rather than produces vapors. The coast mists occur during the season when the land is relatively cold. Near the Gulf of Guayaquil the antarctic current diverges from the coast, so that in the Tumbes valley and adjacent country the conditions in the summer months are such as produce rains. In the remaining valleys of the coast, agriculture is made possible only by means of irrigation, and is accordingly very limited in extent, although rich and varied. In the northern and south-central portions of the coast, plains extend inland from the sea, while in the southern part there is a coastal plain separated from the Pacific by a range of coast hills. Between the northern and south-central plains, as well as between the south-central and southern, the foothills of the sierra descend to the seacoast. The Sierra.-The sierra embraces the high land dominated by the lofty cordilleras of the Andes. In the southern part of Peru there are two cordilleras, the western and the eastern, which enter from Chile and Bolivia respectively, and inclose between them the Titicaca Lake basin. To the north of Lake Titicaca these cordilleras unite in the knot of Vilcanota, south of Cuzco. From this knot three cordilleras, known as the western, the central, and the eastern, extend to the northward, reuniting in the

Jan 7, 1908

By M. F. Goudge

LIMESTONE surpasses any other rock or mineral in the number and diversity of its uses and in the quantity consumed fur industrial purposes. Either in the raw state or when calcined to lime it enters directly or indirectly into the manufacture of a great variety of products and its sphere of usefulness is continually expanding. The term "limestone" as here employed includes all varieties from high-calcium limestone, consisting almost entirely of the mineral calcite, to the highly magnesian variety, largely dolomite. Lime is also discussed .because lime is simply calcined limestone and often the material may be used in either the calcined or natural state. Limestone has been of service to man since prehistoric times but only in the last hundred years has it become one of the most important raw materials in industry. In every industrial country it comprises the greater part of the total stone produc-

Jan 1, 1937

By Frank Armstrong

ALL the mining machinery of the Penn Iron Mining Co. has been operated by electric power for several years and when another shovel for stockpile loading was required the advantages of an electric shovel were naturally considered. After considerable study, serious objections suggested themselves the use of a shovel operated directly by electrical apparatus by reason of the complicated control, severe service on the motors FIG. 1.-ELECTRO-HYDRAULIC SHOVEL FIG:. 2-THE SHOVEL AS IT WAS OPERATED CINDER CONSTRUCTION. THE FIRST YEAR. and the heavy surges of current required from the line. It was finally decided to construct an electro-hydraulic shovel using water under pressure to perform all the necessary operations except that of propelling, for which a separate motor was best suited. A car body with boom, dipper handle and dipper of late design, but without any of the steam machinery, was purchased. A motor-driven centrifugal pump, a pressure tank, an air tank, a small air compressor and water cylinders with plungers, pistons and valves, were installed in place of the; steam equipment. Fig. 1 shows this shovel under construction and Fig. 2 shows it as it was operated during the first year, the summer of 1914. The large tank at the back of the car, in Fig. 1, carried air under

Jan 2, 1916

By F. A. Seward

A1though the expanding Eltran1 configuration has been used in induced polarization exploration for several years, there has been little application of this method to straight resistivity problems. A comparison of results of resistivity exploration by this technique versus those obtained from Wenner configuration surveys reveals a number of advantages in interpretative resolution as well as in field operation. The application of electrical resistivity to ground-water exploration is well known.= In the past a major portion of this work has been accomplished by use of one or more variations of a technique employing the Wenner3 electrode configuration. With the introduction of the frequency domain technique of induced polarization measurements, used primarily in the exploration for disseminated sulfide deposits, there arose the need for an electrode configuration by which potentials could be measured externally to the current electrode spread in order to minimize coupling between current sending and potential receiving circuits. It was also deemed desirable that the configuration would provide information laterally along profile as well as with depth. To reach these objectives the expanding dipole-dipole configuration (which probably first was used in the electrical transient method of exploration and from which the name 'Eltran' was derived) has been adapted to induced polarization exploration. The author has successfully applied the same techniques

Jan 1, 1963

By Frederic P. Dewey

(New York Meeting, February, 1912.) By the old method of determining platinum in ores and bullion, the silver-alloy first obtained in the regular course of assay is parted in strong sulphuric acid and the residual metal weighed. This is re-alloyed with silver by a second cupellation and parted in nitric acid, the residual metal being again weighed. Any difference shown between the two weighings is assumed to be, and is called; platinum. Sometimes it is so, and if any considerable amount of platinum be present, there will be a decided difference between the two weighings; but a slight difference is no real evidence whatever of the presence of platinum. On the other hand, the second weight may equal or possibly exceed the first, even when traces of platinum are present. Again, other members of the platinum group may go into solution in nitric acid more or less. If present, these would be called platinum and escape detection. The method does not provide any direct tests whatever as to the presence or absence of platinum. It is often indecisive, and sometimes jives erroneous results. It is, therefore, quite unsatisfactory. Being called upon many times to determine platinum in a wide variety of materials, particularly when present in very small amounts, I have realized the disadvantages and defects of this old method. In an article on the solubility of gold in nitric acid, 1 I have briefly outlined a method of gathering a little gold out of a solution containing much silver, which furnishes the basis of

Apr 1, 1912

By Mehmet Guney

At the Armatcuk mine in Turkey, various modifications of sublevel methods have been tried during the last decade in an effort to eliminate gob fires, dangers from roof falls, and surface subsidence, and also to increase extraction efficiency. From the experience thus gained, it was decided that the most likely system to give maximum benefits, considering the existing geological conditions and coa1-seam characteristics, was hydraulic stowing. This paper examines trends in the working techniques of hydraulic stowing and discusses the favorable results and technical problems that the method produced at Armutcuk. The Armutcuk mine, a subsidiary of Eregli Coal Mines (EKI), produces 1300 tons of run-of-mine coal daily from thick (about 10-90 ft) and highly dipping (about 50-90°) coal seams. The coal is highly volatile with good coking properties that make it highly suitable for industrial use. Most of this coal is used in the iron and steel industry at Eregli on the Black Sea coast. Complete recovery of the coal is of vital importance to industrial development and progress. Initial coal extraction was carried out by means of a sublevel mining system modified to accommodate local geological conditions and coal seam characteristics. This method is similar to that employed in metalliferous mines. Several problems arose from the application of the method, one of them being the prevalence of gob fires which caused periodic shutdowns in some sections. To achieve maximum coal extraction with minimum dilution, to eliminate gob fires and surface subsidence, and to reduce fatal accident rates, a decision was taken to change from this method to a hydraulic stowing system. The pres- ence of large deposits of conglomerate and sandstone on the surface contributed to the decision to employ this new method. Although hydraulic stowing practices have been carried out in America and Germany, Upper Silesia may, so far as coal is concerned, be considered the birthplace of the method. Here the process was adapted to thick coal seams on a large scale to reduce dangers from gob fires and damage from surface subsidence. Today, the mining system is not only widely used in the coal mines of France, the Saar, India and Poland, but has also been successfully applied to the iron ore and potassium salt mines in Russia and Germany. LOCATION AND HISTORY The Kandilli-Armutcuk coal field, the most western outcrop of the North Anatolian coal basin, extends for five miles along the Black Sea coast (Fig. 1). The Armutcuk Mine is situated on the southern boundary of the coal field about 40 miles from Zonguldak and about 12 miles from Eregli. The history of coal mining in the North Anatolian coal basin goes back more than a century. Mining commenced on a small scale in the Kandilli-Armutcuk coal field in the late 1880's, and from this time until nationalization in 1940 the mines were operated by private Turkish and foreign interests. In 1940, Eregli Coal Mines was established to takeover the management of these enterprises. The Armutcuk Mine was developed for the first time in the mid-1940's. Since then it has been in continuous production and it now produces an annual 440,000-ton run-of-mine output from which 320.000 tons of salable coal is obtained. MINE GEOLOGY The carboniferous inlier of the Kandilli-Armutcuk coal field crops out over an area about three miles long and one mile wide. The major part of the inlier consists of the Namurian formation with only a relatively small area of Westfalian-A visible on the surface (Fig. 2). The Namurian formation, which has no exploitable coal seams in the Armutcuk Mine, consists mostly of arkose sandstones and black shales often having

Jan 1, 1969

By John A. Mathews

RESEARCH in the steel industry, as in other lines of manufacturing, has for its principal purpose the increasing of profits. That is what manufacturing companies are for, and all departments of the organization must be so coordinated as to lead to profitable operation. To divide a payroll into productive and non-productive labor is misleading. Productive labor, in fact, is necessary labor, and non- productive labor is the labor we can get along without. One might as well say that the steering wheel is not a part of an automobile as to say that the directing minds of an industry are non-productive. Legitimate manufacturing profits in a steel company or any other company are the reward that the public pays for service rendered or risk taken. The desire for profits is the impelling motive that leads investors .to take risks and build up industries that give employment to others. Every department of a company, be it executive, manufacturing, financial, sales, or research, must contribute to the one end which brings success-profits.

Jan 1, 1921

By B. P. Nutter, M. Lebourg, J. A. McAlister

The Multi-Flow Evaluator (MFE) is a new system of tools providing an original approach in drill-stem testing. It improves control during the testing operation and gives a more accurate evaluation of the fluid recovered while providing additional pressure information for reservoir analysis. The tools are operated entirely by up and down motion of the drill stem. This up and down operation provides a positive means of control and offers easily observed surface indications of tool operating position. An unlimited number of shut-in and flow periods may be taken with this tool while in the hole. The key to the success of the MFE system of tools is the safety seal packer. Until this development, operation of the tools by up and down motion only had proven unreliable. The success ratio of the MFE now exceeds the ratio achieved by conventional tools. The equipment includes a 2,750-cc chamber in which a representative sample of the flowing formation fluid is trapped at the end of the last flow period and brought to the surface under pressure. The sample can be evaluated at the wellsite or transferred under pressure for laboratory analysis. The sampling feature of the tool allows a sample to be obtained from a reservoir which has suffered minimum influence from production. A representative sample can be obtained for laboratory or empirical analysis by employing a testing technique to minimize drawdown during flow periods. Interpretation methods to take advantage of this additional information are presented and supported by actual field examples. INTRODUCTlON The Multi-Flow Evaluator (MFE) represents the most recent technical advance in formation testing. Drill-stem testing techniques prior to the MFE have been limited in three areas—(1) operaiion, (2) recovery analysis, and (3) reservoir analysis. The tools in the MFE system allow maximum control during testing and provide test information superior to that obtainable with conventional tools. The system of tools and the operation procedures are described to illustrate the mechanical advantages over present tools. Methods of pressure build-up and fluid

Jan 1, 1966

By R. L. Whiting, H. J. Ramey

The basic study from which this paper was prepared was started as the result of the growing need throughout the world for increasing quantities of energy in all forms. Quite obviously, natural forms of energy that are readily available at low development cost are those in greatest demand. The underdeveloped countries — and particularly those having little or no petroleum resources — are the countries in which the most interest is being shown in the newer energy sources. One of the least expensive energy sources is natural geothermal steam.'-* Although this form of energy has been recognized for centuries, it has been only during the past 20 years that serious efforts have been made to harness it. Natural geothermal steam energy in Italy, New Zealand, Mexico, Japan, and California is now being produced through wells to drive turbines and generate electricity. Further, active exploration for natural geothermal steam is being conducted in Hawaii, Fiji, Taiwan, Chile, Russia, Greece, and Katanga. It is surprising to find that most geothermal steam exploration is in the "steam seep" stage. That is, surface studies are made and exploratory wells are drilled in the general area of steam seeps. However, in the larger geothermal steam areas, there have been efforts to apply the most modern geological and reservoir engineering principles in order to define the reservoir parameters, particularly those relating to estimates of reserves and future productivity. This paper is concerned with the development of appropriate equations and techniques to facilitate these estimates. Production of natural steam or hot water presents problems different from those experienced in the production of oil and gas. For example, steam or hot water systems may be essentially single-component systems, while hydrocarbon systems are most frequently multicomponent fluid systems. Heat effects are much larger for water than for hydrocarbon systems; and the natural steam production may or may not be isothermal, while production of petroleum reservoirs is considered normally to be isothermal. Petroleum reservoir engineering principles may be applied to natural steam or hot water reservoirs if the inherent differences in the systems are considered. The basic considerations involved in geothermal steam reservoir engineering are: thermodynamics, physical and thermal properties of water, materials and energy balances, fluid influx, and performance matching and predicting. Thermodynamics Fig. 1 is a pressure-temperature diagram for the liquid-vapor region for pure water, showing the critical point and five other points representing possible initial conditions for a geothermal steam reservoir. To generate a physical appreciation for the mechanics of natural steam production, it is helpful to consider

Jan 1, 1970

By J. K. Gustafson

Since prehistoric times, gold has been sought for its beauty and its unusual physical and chemical properties. Early in the dawn of civilization it became the ultimate unit of value, and for at least 6000 years it has been used to barter for other commodities. It has been prospected for, treasured and made into works of art and personal adornment. From time to time, it has even been the object of conquest. Because of its predominant role as a basis for money in recent centuries, economists have come to think of gold solely in these terms. Gold, however, has physical and chemical properties that make it one of the most useful metals in the modern world. It is the most ductile metal known. An ounce of it can be drawn into a continuous wire over 35 miles long. It is also so malleable that an ounce of it can be beaten into films 0.00001 in. thick covering 68 sq ft of surface. It has a density of 19.3 and is so heavy that 1 cu ft of it weighs more than half a ton. Gold is nonmagnetic and has a high electric conductivity that is only slightly less than that of silver and copper. Gold is so inert to all the chemicals found in nature that gold coins and jewelry buried beneath the soil or at the bottom of the sea for thousands of years appear to be as bright and perfect as when they were first immersed. Finally, gold has an extremely high reflectivity of both light and infrared rays.

Jan 1, 1971