Search Documents

By Lidong Teng

ArcSaveTM is a new generation of electromagnetic stirrer (EMS) from ABB for electric arc furnace (EAF) operation. Its goal is to improve the safety, increase the productivity and reduce costs. Electromagnetic stirring in the melt bath during arc furnace operation will affect the scrap smelting, bath temperature distribution, refining reactions, and also the tapping practice. This paper has summarized the investigation results obtained from the first ArcSaveTM system installed in a 90 ton EBT arc furnace in USA. The hot test results show that ArcSaveTM has enhanced the heat and mass transfer in the arc furnace process. This results in a faster scrap melting rate, lower slag superheat during arcing, more homogenous melt bath, higher decarburization rate and higher EBT free opening frequency. ArcSaveTM has also reduced the tapping temperature and tapping oxygen in the steel. This brings a higher scrap yield and saves ferroalloy consumption in the downstream ladle furnace operation. The lower energy consumption, short tap-to-tap time, and consistent furnace operation bring increased productivity and safety.

Aug 16, 2017

By Anna Carolina Cerqueira Neves

Synthetic fibers have been gradually replaced by lignocellulosic fibers. Compared to the synthetic fiber, natural fiber showed economic and environmental advantages presenting interfacial characteristics with polymer matrices that favor the impact energy absorption by the composite structure. However, so far little has been reported about the hemp fiber embedded in polymer matrices, such as tensile properties. This study aims to evaluate the resistance in tensile tests of epoxies composites reinforced with different percentages of hemp fiber. Tensile tests were submitted with percentage of 0%, 10%, 20% and 30% incorporated hemp fiber in epoxy matrix. The tensile strength and deformation substantially increased the relative amount of hemp fibers incorporated into the polymeric matrix.

Aug 16, 2017

By Jari Larkiola, Aarne Pohjonen, Juha Jokisaari, Oskari Seppälä, Joonas Ilmola

Finite element method (FEM) is widely used to model the hot strip rolling process. Flatness defects e.g. front-end bending in multipass hot strip rolling is studied by authors using a finite element (FE) model with interactively operating automated controlling logic (ACL) [1]. However, industrial corresponding grade of accuracy in strip thickness subsequent to the rolling pass is not easily accessible in FE-model without separate calculation of significant rolling parameters and integrated roll gap control. In order to study flatness defects and optimize pass schedules the controlling and physics of the FE-model must correspond to the industrial process. For this need the automated controlling logic is upgraded by setup calculations to predicting roll force and work roll flattening. These predictions are utilized in setup positioning of a work rolls. Reliable setup calculation enables smooth multi stand rolling process without significant additional adjustment of roll gap clearance. State of art rolling technology requires above-mentioned setup controlling for the FE simulations to simulate different pass schedules without time consuming preparations. Operational setup calculations together with automated controlling logic of hot strip rolling enable simulation of new pass schedules and efficient problem solving.

Oct 1, 2019

By Samuel Filgueiras Rodrigues, Clodualdo Aranas Jr., Gedeon Silva Reis, Eden Santos Silva, Fulvio Siciliano

When austenite is deformed above the Ae3 temperature, partial amount of it transforms dynamically into ferrite by a displacive mechanism. After unloading, it retransforms back into the stable austenite by a diffusional process. This influences the rolling load which decreases under isothermal condition or does not increase with decreasing temperature as rapidly as expected under cooling. Plate rolling simulations under isothermal and continuous cooling conditions were carried out on a 0.09 wt.% Nb X-70 steel. Pass strains of 0.2 were employed together with interpass times of 10 s, and 30 s for the cooling conditions and 0.3 with interval of 10 s at 900 °C for the isothermal experiments; strain rate of 1 s-1 was used during the simulations. The mean-flow-stress (MFS`s) behavior of both conditions indicates that dynamic transformation and dynamic recrystallization were taking place during straining. The critical strains for the initiation of dynamic transformation fell around 0.06 while the critical strain for DRX was 0.12. It has been shown that ferrite is formed due to the applied deformation of roughing passes and increases its volume fraction throughout the finishing rolling stage. Under cooling conditions, the ferrite formation is also favored as the temperature approaches the Ae3 line. Such ferrite forms when the driving force for dynamic transformation is higher than the total free energy barrier preventing its formation. This obstacle consists of the free energy difference between austenite and ferrite as well as the lattice dilatation work and shear accommodation work. The addition of Nb retards the retransformation of the ferrite into austenite. Moreover, holding times after rolling increases the amount of austenite available for microstructure control on subsequent stages. The dynamic transformation (DT) mechanism can be used to design improved rolling schedules

Oct 1, 2019

By Leonardo Araújo Peruch, José Fagundes, Henrique Carneiro Pinto, Marco Túlio Costa, Nayara Coutinho, José Fabiano Martins Assunção

The objective of this project was to increase the hot charge by reducing reheating energy consumption and raising the productivity of ArceloMittal Tubarão's hot strip mill by changing the HSM’s schedule process with optimization of the relocation process of slabs after HSM’s chance with focus on slab temperature in reheating time. The project began with the revision of metallurgical rules for the relocation of materials, definition of criteria temperature setting (hot / cold), definition of restrictions of the process and review of modus operandi scheduling process. With the implementation of the process / system it is expected to achieve a 10% increase in the hot charge index in slabs reheating furnaces and increase productivity of the ArcelorMittal Tubarão hot strip mill

Oct 3, 2019

By Woo, Hur, Kim, Ki Nam, Seung Min, Kyoung Sik

Tandem cold mill (TCM) is a process to obtain flatness as well as thickness desired by the customer by rolling hot-rolled coils continuously. The final stand of the TCM plays the most important role of flatness control, which usually uses the real-time measurement at the exit. However, as the material property increases, it is not easy to handle flatness with only the final stand. In order to overcome such a limitation, we propose a feedback control method to strengthen flatness control for non-final stands. The proposed method was tested in an actual production line, and the effect is proved for 45K or less steel grade.

Oct 1, 2019

By Rogério Martins Pereira, Charles Pierri de Souza, Lucas Gabriel Correa

The Tandem Cold Mill is composed by stands with rolls positioned so that the rolling force can be transmitted to the strip being processed. Due to the mechanical stresses inherent in the process, the roll bearings are heated and are equipped with lubrication and cooling systems. Nevertheless, there is the challenge of continuously monitoring the temperature of the bearings, which would allow preventive intervention in case of overheating. This paper presents an in-house solution to temperature measuring system applied to the backup roll bearings of a continuous Tandem Cold Mill. The system uses Zigbee technology and is integrated with the main control system, allowing early diagnosis of bearing heating and proper intervention. Results and features of the system are discussed.

Oct 1, 2019

By Henara Lillian Costa

This paper aims to investigate the effects of a possible incorporation of ethanol to the lubricant during engine use on friction and lubricant film thickness, by adding small amounts of ethanol to Group I base (with and without an organic friction modifier) and to formulated oils. Film thickness was measured using ultrathin film interferometry. Friction tests were carried out using a mini-traction machine to obtain Stribeck curves. The film thickness measurements showed that in the region of low speeds, where the elastohydrodynamic film is very thin and therefore boundary lubrication may prevail, the addition of ethanol produced some boundary film, which was not present for the base oils. For the base oil with an organic friction modifier, the presence of ethanol increased the thickness of the low friction boundary film. For the formulated oil, the addition of ethanol reduced film thickness in all lubrication regimes. The friction tests showed some friction reduction due to addition of ethanol to the base oil, in particular at low speeds. For the formulated oil, the addition of ethanol reduced friction at high speeds, which was associated to a reduction in the viscosity of the lubricant, but at low speeds, the presence of ethanol reduced the formation of a boundary layer, increasing friction. For the base oil containing an organic friction modifier, the presence of ethanol increased the range of speeds for which low boundary friction occurred.

Jul 31, 2018

By Wolfgang Kern

More and more coke oven plants worldwide face the task to improve their emission reduction at their coke oven batteries. In the 90’s PROven® was invented and developed by DMT to regulate the inner pressure of a single coke oven chamber. Generally, most of the coke oven chambers can only close and open their connection to the collecting main but without the possibility to regulate the pressure during the carbonization time. Through the installation of PROven® the load on the coke oven door sealing system and the charging lids will be decreased and so does the emissions of crude COG as well. The current PROven® system, installed in the collecting main, does not only regulate the chamber pressure, it replaces the valve between the goose neck and the collecting main, too. This variable pressure control allows decreasing the leakages at the emissions sources to a minimum and allows operating the collecting main under optimum pressure. Subsequently, this will lead to enhanced emission reduction. PROven® proved its value with more than 2,100 units installed by licensee worldwide. Nevertheless, DMT is always focused on its client’s needs and therefore enhance PROven® to provide the Best Available Technique (BAT). Among the main features of the now available system is the plain arrangement with a higher reliability and the possibility to install the system outside of the collecting main without modifying it. Hence, upgrading coke oven plants during operation is possible without any noticeable impact on the plant operation.

Aug 1, 2018

By Michel Rodrigo Luiz, Glaucio Augusto Polini, Giardini F. Lazzarin

ArcelorMittal's pickling and cold rolling line has been demanded to increase production since the installation of equipments in 2015. In addition to the improvement in productivity related to these new equipment, one of them the automatic surface inspection system (SIAS), work has also been developed in other equipment seeking improvement of production indicators. The present article exposes the actions and gains that were achieved with actions on two equipments in the same section as the Side Trimmer. The first one deals with the optimization of time gains with sequencing adjustments without financial contribution, using only internal labor seeking reduction of unproductive times by adjustments of the side trimmer in the cold strip mill. The second item discussed demonstrates the actions and the gains generated due to the availability of new resources (installation of SIAS equipment), the optimization of these resources seeking a focus on the reduction of ruptures in the tandem cold mill, configuring the same in the aid of the identification of critical defects and also in the automatic speed reduction action of the tandem cold mill in defects considered serious. In both cases the intention was to improve production, seeking to improve the results of the section and the line.

Oct 1, 2019

By Jesús A. Carlos Cornelio

Since their discovery in 1991 Carbon nanotubes (CNTs) have attracted much interest due to their remarkable mechanical, thermal, electrical, chemical and optical properties. In connection with their mechanical properties, CNTs have been studied in various forms for tribological applications including their use as lubricant additives for oil and water. In this paper the tribological properties of CNTs (SWCNTs and MWCNTs) when used as lubricant additives are studied under rolling-sliding conditions in a twin-disc testing machine. The tests were performed using 5% of creepage and pressures of 0.8 GPa and 1.1 GPa. Used functionalized nanotubes were modified with carboxylic acid ultrasonically dispersed at different concentrations (0.01, 0.05%). The results indicated that the presence of carbon nanotubes leads to a decrease in both friction coefficient and wear rate for both systems studied (oil and water).

Jul 31, 2018

By Luca Tommasi

Danieli complemented its wide range of production plants for the iron and steel industry with a further step upstream into iron ore pelletizing and beneficiation. Danieli has engineered and constructed a state of the art and fully automated pilot plant facility – pot grate and sinter box – at Altos Hornos de Mexico S.A. (AHMSA) Pelletizing Plant, Monclova, Mexico. Installation and commissioning were completed in October 2009. Key features of the pot grate include the avoidance of the need for operator intervention during the test, automatic system preheat, absence of dead time, heat recuperation system with an air/air heat exchanger, oxygen control in preheating and firing with zirconia oxygen analyzer, possibility to test deep beds up to 625 mm. A series of projects have been accomplished by AHMSA availing of the pot grate facility with the aim to enhance pellet plant productivity and to reduce operating costs. The results obtained by use of Danieli pot grate combined with the experience and skill of plant operators has shown significant technical and economical benefits thus fully justifying the initial investment made by AHMSA and confirming the importance of having an in-house testing facility in order to optimize industrial plant operations.

Aug 16, 2017

By Alberto Pesamosca

The paper presents the results obtained by the AC EAF supplied by Danieli at Kroman Çelik (Gebze-Turkey) after the planned upgrade to 150 ton. The EAF – 7,4 m diameter, based on the full platform standard design - is able to handle a maximum power of 114 MW and is equipped with the most advanced and reliable technology, including module injection system and the Hireg electrodes regulation system. Excellent results were already obtained with 120 heat size in terms of fast start-up and excellent performance figures. After the upgrade, productivity was increased up to 212 t/h, maintaining high process efficiency (365 kWh/t with 32,1 Nm3/t O2).

Jul 30, 2018

By Breno Totti Maia

In these hard days for Brazil steel market, all steel shops want to achieve the same goal, work with: productivity, low costs and high performance. In this scenario the Slagless® technology (which is applied into BOF converter) was important to reach these targets. After use has been reduced the number of times of tip exchange in more than 04 times. Was reduced too, the time to remove lance skulls. Lance keeps clean during all his life with record number of the life 1255 .Blow keep stable due strong measure control at the nozzles and more improvements are planning.

Oct 30, 2017

By Diego Berti Salvaro

The morphology, dimensions and chemical composition of tribolayers strongly depend on the pressures and temperatures acting on the contact. They are formed by reactions between the surfaces in contact with each other as well as with the atmosphere, lubricants and possible contaminants. In this paper the influence of test time (180, 500, 1000 and 2500 h) into the formation and characteristics of tribolayers in pairs DLC-stainless steel tested under refrigerant gas R134a atmosphere without presence of lubricating oil was analyzed. The characterization was performed using scanning electron microscopy, energy dispersive spectroscopy (SEM-EDS) (morphology and chemical composition) and white light interferometry (dimensions). The tribolayers thicknesses ranged from 100 to 500 nm and they were composed by elements originated from mutual transfers between the tribological pairs as well as oxides, being more pronounced on the stainless steel surface. The results show that the tribolayers are chemically stable (maintained the same composition over time) and the thickness remained stable after a thousand hours of testing.

Jul 31, 2018

By Silvio Cecchini

State-of-the Art Mould Level Control Solutions for continuous casting applications face different challenges. On the one hand, technological phenomena such as clogging and unclogging, unsteady bulging or waving can create unpredicted meniscus disturbances by completely changing the casting channel geometry and the flow behaviour of liquid steel to the mould. On the other hand, from the viewpoint of caster operations, long lifetime, quick interchange-ability and integration capability into existing systems must be achieved. In the present contribution, the overall development of INTECO TBR’s mould level master – a comprehensive mould level control solution for all continuous casting applications – will be introduced. The basis for the presented system is a development over several years which includes investigations of all critical components such as shroud, stopper, stopper mechanism, servo actuator and mould level control program. These investigations finally resulted in a new-ly developed control algorithm for a highly dynamic servo actuator. The control algorithm with its basic functionality such as the prevention, identification and removal of clogging impacts with the associated automation functions to reduce their influence onto the overall mould level control performance will be presented. The scientific basis, the resulting control functions and their related automation implementation will also be illustrated. Finally, a patented control algorithm and control functionality for unsteady bulging and waving effects with the associated automation functions to reduce their influence onto the overall mould level control performance.

Aug 16, 2017

By Leandro Rigo Ramos, Marcelo Lucas Pereira Machado, Lumena Gloria de Souza Nunes, Mariana Valinhos Barcelos

The aim of this work was to study the influence of temperature on the grain refining process from severe plastic deformations through the simulation of Accumulative Roll Bonding (ARB) by torsion tests. The assays were performed to simulate the ARB at three different temperatures of 550 ° C, 625 ° C and 700 ° C with 5 torsion cycles with equivalent strain of 0.8 per cycle at a rate of 0.1−1 , totalizing an accumulated deformation of 4.0. Grain refining was obtained with an average size of 2μm, 5μm and 6μm for the temperatures of 550 ° C, 625 ° C and 700 ° C respectively. There was a rise in Vickers hardness by 68%, from 119HV in the annealed sample to 175HV in the deformed sample at 550 ° C. In the deformations at 625 ° C and 700 ° C the value of 130HV E and 150HV respectively was obtained. Based on the obtained results, it can be stated that the severe plastic deformations in microliged steel, carried out at temperatures lower than the end of the austenite-ferrite transformation, produce refined grains of the order of 2μm and, consequently, increase the mechanical strength of the material.

Oct 1, 2019

By Danilo Gonçalves de Oliveira, Rogério Martins Pereira

Chatter is a widely studied vibration phenomenon that affects most cold mills around the world and its impact on these lines are tremendous: from productivity and quality losses to mechanical equipment damage. The investigation of its origins and how to minimize the occurrences and their impact on the equipment require special instrumentation and algorithms in order to have a detection of the vibrations as soon as they start. This paper presents three methods of identification of chatter on a Tandem Cold Mill and the actions to leave the vibration frequency range before its amplitude achieve catastrophic values.

Oct 1, 2019

By Richard Harvey, Robert Paul Mawer

In recent times there has been an increase in the demand from Steel plants for a technology that offers the most economical environmentally sustainable solution. In terms of blast furnace off gas cleaning this has seen a drive towards Cyclone technology replacing the older Dustcatchers. Cyclone technology can achieve dust removal efficiencies as high as 95% increasing the dust yield at the primary stage of gas cleaning. The dry dust (rich in Fe and C) can then be recycled to the Sinter Plant or Blast Furnace. Capture of dust at this stage also has the benefit that sludge generation from the secondary stage is also reduced meaning less waste to landfill and / or recovery of some of the by-products for further use. Primetals Technologies already offer a state of the art Tri-Axial Cyclone installed on many sites world-wide, however, this paper focuses on a hybrid of this technology, the DustClone. The DustClone is a low CAPEX unit that is essentially a Cyclone housed inside the Dustcatcher. This unit is aimed at operators who may be carrying out smaller scaled shutdowns / repairs that normally have a reduced CAPEX. This paper describes the technology that Primetals Technologies have developed.

Oct 1, 2019

By Marcel Antonio Arcari Bassani

In the mining industry, it is common to have data collected in various formats. In an open pit mining operation, at the early stages of exploration samples are obtained from diamond drillholes. During the production stage, samples are collected from blastholes. The last is more numerous but less precise. From a geostatistical view, this dissimilarity has to be considered to integrate the two sources of information. To combine this different data, three methodologies were investigated: simple kriging with local varying mean, cokriging and ordinary kriging. The exhaustive Walker Lake data set was used and it is considered the source to obtain the true grades. Initially, samples were obtained from the exhaustive data set at a regular spacing grid of 20 x 20 meters. Next, samples were obtained again from the exhaustive dataset at a regular spacing of 5 x 5 meters and a relative error of 25% was added. Then, both data were used to estimate blocks using the three methods mentioned. The grade tonnage curves were compared with the true block grade distribution. Moreover, the block misclassification was evaluated. The results showed that ordinary kriging produced estimates closer to the true block grade distribution and reduced the block misclassification.

Aug 8, 2018