Search Documents

By G. G. Huggins

A demonstration project has been completed to reduce the operator sound level of an underground service vehicle, a personnel dispatch wagon, to go dB(A) or less. The program objective was to implement quieting recommendations made on an earlier study for the USBM n diesel-powered mine equipment. The manufacturer and mine to which the vehicle was going actively participated in the program to ensure a product that was not only quiet, but useful. The key element of the quieting package is an engine part a1 enclosure, which, with several complementary noise control components, reduced the operator sound level 14 dB, from 101 dB(A) to 87 dB(A). The vehicle underwent a 4-month trial period, with no degradation in the quieting package. Mine personnel reported no maintenance difficulties, and were enthusiastic about the dispatch.

Jan 1, 1975

By M Wimmer

LKAB operates two underground iron ore mines located in the northern part of Sweden, both using sublevel caving (SLC) as the mining method. Knowledge of the mechanisms of gravity flow is important since it affects both ore recovery and waste dilution. This paper describes results from a large-scale field test carried out at the Kiruna mine with a focus on gravity flow. It is part of Work Package 2 in the I2Mine project financed by the EU. A total of ten rings were blasted. Smart Markers based on radio frequency identification technology were used to monitor the gravity flow. An accurate delineation of the isolated extraction zone requires reliable detection of all recovered Smart Markers and precise knowledge of the 3D position of the markers within the burden. It was therefore necessary to carry out borehole deviation measurements (collar, alignment and trajectory). The blast performance was monitored by high-speed filming, near-field vibration monitoring and velocity of detonation measurements. Three-dimensional stereo images were taken from the drawpoint and the loaded bucket after each mucking cycle. Based upon that, fragmentation was assessed both in 2D and 3D. Furthermore, volumetric differences were determined at the drawpoint, which reflects the mobility of loaded material. For draw control, the Fe content is estimated by measuring weight and assuming a full bucket. The measured volume of rock in each bucket further improves this estimate. Possible flow disturbances occurring at the drawpoint were revealed by video recording. Two-dimensional laser scanning was carried out during mucking to track the position of the bucket and estimate the position and slope of the muck pile.The results from this test clearly show that the gravity flow in the large-scale sublevel cave in Kiruna mine is often of disturbed character. Standard draw occurred only in three rings and shallow draw in the remaining seven rings. In five cases, shallow draw developed towards standard draw, but occurred at rather late stages during extraction (70–125 per cent). The maximum width of the draw varied between 10 m and 13 m except for one ring (6 m). The draw reaches the cave rather early (5–25 per cent extraction) in shallow draw situations and much later (about 50 per cent) during standard draw. Waste originates from above in most cases, while more significant portions often occur at about 20–45 per cent extraction.All the results from this extensive field test are not yet fully analysed, and further field tests are planned. A more detailed insight into gravity flow in large-scale SLC and possible influence by drilling, blasting and the mucking procedure is expected in the future.CITATION:Nordqvist, A and Wimmer, M, 2016. Holistic approach to study gravity flow at the Kiruna sublevel caving mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 401–414 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Y. M. Chen, H. L. Zhang, W. U. Bing, C. Q. Zhou

Multiphase flow in the widely used Vanyukov furnace was numerically studied. An unsteady three-dimensional and three-phase flow model was firstly built using the computational fluid dynamics (CFD) software ANSYS FLUENT®, and then solved with the volume of fluid (VOF) and k - ??model. The results showed that the proposed model could be used to predict the multiphase movement, the slag/air fluctuation, the vortex formation, and effects of structural and operational parameters. By fast Fourier transform (FFT), the dominant frequency of density with time signal was calculated as 0.29 Hz. The analysis of different injection flow rates of enriched air indicated that this variable has a major effect on the mean slag velocity. The peak mean velocity increased from 2.17 to 4.99 m/s while the flow rate of enriched air varied from 70 to 160 m/s. The proposed model provides a method to optimize the furnace structure and operating conditions for the best furnace performance and lowest energy consumption.

Jan 1, 2015

By M. R. Smith, H. Kanli

The impact crusher is a popular device for producing crushed aggregates from non-abrasive rocks such as limestones, offering the advantages of high reduction ratios and relatively low installed costs. To extend the application of a process-flowsheet simulator to the quarrying industry, a mathematical model of an impact crusher was therefore developed using the general crusher models of Andersen and Whiten as a basis

Aug 1, 1995

By Conochie D. S, Grave N. C

Disposable-tip emf cells at present used in liquid steel can be used to measure the state of oxidation of high-iron slags produced in non-ferrous smelting. This provides a new tool for the control and evaluation of pyrometallurgical operations.An investigation of oxygen potential variations throughout a typical nickel smelter using the flash smelting technique gave a valuable insight into the process. Correlations of oxygen potential with ferric to ferrous oxide ratio and nickel content in slag were in reasonable accord with equilibrium data in the literature indicating that the probes may be used both as a plant investigation tool and possibly as a means of obtaining thermodynamic data for slags.

Jan 1, 1979

By James S. Graham

Research at the University of Colorado on southern pine and Douglas-fir piling has determined that the existing building code design stress values of 1200 psi and 1250 psi, as determined by ASTM D-2899, are substantiated; but testing procedures should be revised. All full size piling tests should be standardized at 1/d ratios of 2:1, or confined tests performed. Also, it has been determined that theoretical design values for timber piling should not be based on the lumber criteria of D-245 and D-2555, but instead should follow the pattern set by engineers in the utility industry for timber poles, in accordance with ANSI 05.1.

Jan 1, 1986

By Frank E. Cash

Although during the past 10 years Alabama has attained an enviable position by its coal-mine accident experience and, like most of the other coal-mining States, has made progress in the safer operation of coal mines, there is still room for improvement, which can be realized only by still greater efforts on the part of employees and employers. From 1993, when accidents were first recorded by the Alabama State Mine Inspection Department, to 1934, inclusive, 3,451 men lost their lives in the production of 569,722,676 tons of coal. The primary purpose of this report is to bring to the attention of the mining industry in Alabama end elsewhere statistics of fatal accidents for 1931-34, with the hope that a study of the causes may lead to reduction of similar accidents in the future.

Jan 1, 1936

The safety of mining operations is significantly influenced by the in situ stress fields in which the mining excavations are created. From the point of view of planning of mining operations, the in situ stress field is a most important input parameter for valid modelling of excavations. Many in situ stress measurements have been carried out for mining and civil engineering projects in southern Africa over the past 30 to 40 years. A database of in situ stress measurement results and observations has been compiled. This paper presents results extracted from the database which are considered to be of particular interest to mining areas in South Africa. The database will permit the estimation of likely stress conditions in new areas of mining, provide a basis for evaluation of results from future in situ stress measurement programmes, provide a basis for comparison of observed behaviour with expected behaviour, and provide a source of data on which realistic design and layout analyses can be based. The information contained in the database indicates that horizontal to vertical stress ratios in the Carletonville, Klerksdorp and Rustenburg areas are significantly higher than the value of 0,5which is commonly used in mine layout planning.

Jan 1, 1998

By Willem Le Roux

1.1 Section 47(1) of the Mine Health and Safety Act, 29 of 1996 (?the MHSA?) establishes a Mine Health and Safety Inspectorate which is administered by the Chief Inspector of Mines. The Mine Health and Safety Inspectorate is part of the Department of Mineral Resources. The Chief Inspector is appointed by the Minister of Mineral Resources (see section 48(1) of the MHSA). 1.2 The Chief Inspector must, amongst other things, ensure that the provisions of the MHSA are complied with and enforced, and that all the duties imposed upon the Chief Inspector and the other Inspectors of Mines in terms of the MHSA and any other law are performed. The Chief Inspector of Mines must appoint Principal Inspectors of Mines and Inspectors of Mines to assist him/her to discharge his/her duties (see section 49(1)(a) and (c) of the MHSA).

Jan 1, 2011

By Dennis McLaughin

This report contains a description of the contract activities performed by ENSCO, Inc. under contract No. H0178069. The purpose of this project was to enhance the Bureau of Mine?s Cableless Electronic Survey System use to aid in the drilling of long (approx. 2000 feet) boreholes in coal. This drilling is performed as part of the methane drainage program. The system that was ultimately developed was field tested 2nd demonstrated in actual in-mine drilling activities. The significance of this system as compared to previous drill survey systems is the fact that it surveys without having to be inserted and removed for each survey point. It is so designed that it can withstand the shock and vibration experience by the drill string during drilling. This means an increased productivity is now possible in that drill operators can determine drill bit positioning in a near real-time environment.

Jan 1, 1981

By R. G. Fleck, W. R. Webb

Iron ore mining in the Adirondack region of northern New York dates back to the Revolutionary War. It is recorded that Benedict Arnold in his campaigns in the Lake Champlain area during the American Revolution utilized the local ores to produce armament and cannon balls. Through the efforts of early pioneers, the iron mining industry in northern New York gained impetus so that in the 1880's mines in the area accounted for nearly one fourth of the iron ore produced in the United States. Both magnetite and red hematite ores were mined during this period. With the discovery of the Lake Superior ores, the iron ore industry in New York started to decline and remained relatively unimportant until 1938. Modern day methods of mining and beneficiating sufficiently high tonnages of low-grade ores to justify the large expenditures for plant and equipment prompted a resurgence in northern New York mining. During the past several years, the production of iron ore from the Adirondack magnetites has greatly increased, and production which amounted to .6%, of the United States total during the 1918-1928 period (Mining and Metallurgy, November 1943) has been increased to 2.85% of the total in 1948. Today, Republic Steel is mining in the Port Henry-Mineville and Lyon Mountain areas; the

Jan 4, 1950

By Joram M. Amir

Even when they are cased! [ ] In bored piles, as well as in drilled shafts, and in caissons too, defects will occur! [ ]

Jan 1, 2001

By Patrick Cloutier

Presentation objectives ? Introduce discrete-event 3D computer simulation as a tool to design, improve and optimize construction projects: ? Describe a real typical construction project planning issue. ? Present an applied use of simulation to solve this issue. ? Detail benefits of using simulation versus traditional planning methods.

Aug 1, 2013

By R. L. Grant

[Detonators are used to explode permissible explosives, dynamites, or other high explosives. This explosion or detonation is brought about by the energy which is liberated as a combination of concussion and heat when the detonator is fired. In Other words; "The detonator is the key which unlocks the energy of a high explosive" (8)4. Being sensitive and latently dangerous, detonators must meet two primary requirements: They must be safe to handle and must detonate when desired, thereby imparting detonation to the explosive charge.]

Jan 1, 1941

By Charles D. Haynes

Outside air for ventilating coal mines in Alabama varies considerably in both temperature and moisture content during the year. Alternate condensation and evaporation of the moisture on mine roofs may result in stresses detrimental to the strength of mine roof. It is well known that the clays in shales absorb moisture, and many investigations have noted the weakening of shales by absorption of moisture. Parker (1970) concluded that there is an annual cycle of rock deterioration in mine roof rock caused by the annual temperature-humidity cycle at the surface. He further noted that moisture reduces the strength of dry rock by one-half, that moisture added to dry rock can cause failure in compression, and that drying of wet rock causes tensile stress buildups by shrinkage. His recommendations for alleviating the moisture-temperature problem was to seal the rock in critical areas and to control ventilation so that air temperature will be lower than rock temperature. The latter recommendation will avoid condensation on the rock surfaces. Hartmann and Greenwald (1941) published the results of a very comprehensive experimental project to determine the effect of temperature and humidity changes on the behavior of mine roof. Their general conclusions included statements that roof rocks were very sensitive to moisture changes, but had low coefficients of thermal expansion. The coefficients were twice in the direction normal to the bedding plane as compared to the parallel

Jan 1, 1975

By M Shaffer, D C. Grant, D J. Goudie, P Sylvester, C Voisey

Scanning electron microscope–Mineral Liberation Analyser SEM-MLA can be used to discriminate between hematite/magnetite in iron ores, but achieving backscattered electron (BSE) segmentation between the two minerals is difficult for particles =75 µm using typical preparation and analysis methods for the MLA based on a tungsten filament SEM (Quanta 400) with 25 kV high voltage. Preparing iron ore sample mounts using a slow-speed polishing method, and conducting the experiment on a field emission gun SEM-MLA (Quanta 650) with the high voltage (HV) setting lowered to 15 kV reduces instrument noise and results in very clean BSE images and segmentation. This method requires new X-ray standards to be acquired for each mineral identity at 15 kV because of major changes in the spectra at lower kV. However, once these X-rays are added to the mineral reference list, effective segmentation can be achieved and a proper analysis obtained.CITATION:Grant, D C, Goudie, D J, Voisey, C, Shaffer, M and Sylvester, P, 2017. Discriminating hematite/magnetite via scanning electron microscope–mineral liberation analyser in the - mesh size fraction of iron ores, in Proceedings Iron Ore 2017, pp 541–548 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By T Nassis, P Louw, M R. Fry, T du Toit

Business intelligence (BI) and business analytics (BA) are established IT technologies that are used extensively in the business environment. This paper discusses the use of these technologies in production environments and beneficiation plants.Assmang’s Khumani mine is an iron ore operation located in the Northern Cape, South Africa. Assmang Limited is jointly owned by African Rainbow Minerals Limited and Assore Limited. This paper presents a case study of a BI solution applied to this plant, which is used by metallurgists, supervisors and all levels of operations and management to extract and analyse data to control and optimise the operation of the plant.The main advantage of adopting an established BI solution is the ease with which production personnel can extract and analyse data. The data is easily presented in familiar spreadsheets and no IT staff or specific training is required to achieve this.The solution adopted at Khumani mine uses a data mart with a multidimensional model (called an online analytical processing (OLAP) cube) acting as the main repository and source of data. The OLAP cube simplifies the access and analysis of plant data.The OLAP cube stores data in a specifically-designed way, which allows extraction and analysis to be performed quickly. It is designed to hold large amounts of data on a long-term basis, which could be for the life of the plant. It also performs automatic aggregations over many dimensions on a background process.A major benefit in adopting such a BI solution is that it allows common BA methods to be applied. This is due to both the efficient long-term storage of data and the availability of standard BA tools. BA tools are now able to perform data mining, predictive analytics, forecasting and other machine-learning algorithms. This paper presents the possible use of such advanced data analysis methods in a beneficiation plant.CITATION:Fry, M R, Nassis, T, Louw, P and du Toit, T, 2015. The use of common business intelligence and analytics tools in the operation and optimisation of iron ore process plants, in Proceedings Iron Ore 2015, pp 129–138 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By A B. Phillips

This paper details the approach adopted to upgrade the current metallurgical facilities at both the Driefontein and Kloof Gold Mines in the Republic of South Africa. Goldfields Ltd operates eight metallurgical plants within South Africa of which three have recently been upgraded to replace the older technology previously installed, with modern equipment. This upgrade was undertaken with a view to improving extraction efficiencies and to reduce operating costs. The upgrade was undertaken in a phased approach with the first phase focused on the replacement of the filtration/zinc precipitation processes with modern pumpcell carbon-in-pulp technology. Included in this upgrade phase was the installation of an automated hands-free electrowinning cell, which represents the first commercial application of its kind in the industry. The second phase of the upgrade entailed replacement of the multiple comminution stages previously installed with large SAG and SAG/Ball mill combinations. Due to the rapid return on these projects, a fast-track approach was adopted which necessitated the purchase of available good conditioned second-hand mills from both within South Africa as well as in Australia. Goldfields Ltd is a large mining house with gold mining operations in South Africa, Australia and Ghana. A well advanced PGM exploration project is underway in Finland- Arctic Platinum.

Jan 1, 2003

By B. M. Coombes

The McCracken and Stacey (1989) method of assessing geotechnical risk for largediameter raisebored shafts has been the basis for most Australian pre-construction raisebore investigations for the past 20 years. At the time of its publication, the McCracken and Stacey (M&S) Method did not include a database of raisebore diameter and rock mass conditions versus actual performance. It did, however, provide a chart that quantified geotechnical risk in terms of proposed shaft diameter and the raisebore rock quality index, QR. Two parameters, RQD/Jn and Jr/Ja were identified as being critical to raisebore stability, but the contribution of these to overall raisebore stability was not quantified. Peck and Lee (2008) published a database of raisebore performance from Australian case histories. Raisebore diameter and ground conditions, in terms of a Lower Bound QR value, were presented for 50 cases versus raisebore performance. This paper updates the database with further case histories and corrected SRF values. This paper further evaluates the reasons for the variable raisebore performance for similar RSR values. For all case histories, three parameters, RQD/Jn, Jr/Ja and Jw/SRF are investigated to assess their influence on raisebore performance.

May 1, 2011

By M. J. Price

The usage of Geographic Information Systems (GIS) is increasing rapidly throughout the Mining Industry, especially in the Industrial Minerals sector. GIS provides an efficient and robust link between spatial (often CADD) and tabular (database/spreadsheet) components. Mineral economists and corporate planners employ GIS to perform market analyses, to source raw materials, and to schedule and monitor deliveries to customers. Exploration and acquisition groups apply spatial analysis to identify high quality resources that meet economic guidelines. Mining regulators and environmental affairs departments expedite and monitor permitting, environmental compliance, and best management practices reclamation through GIS data management and Electronic Permitting. Operations staffs monitor overburden removal, material extraction, quality control, and stockpile volumes with GIS. This paper summarizes the many aspects of GIS in Industrial Minerals. It also introduces and addresses issues and concerns commonly encountered during a mining GIS implementation.

Jan 1, 2001