Search Documents

By Adrian Daniel

"Dating back to 1934, Con Mine is located directly south to the city of Yellowknife in the NWT, Canada. With mill operations ceasing in 2004, a challenging surface remediation situation resulted which required the treatment of close to 40,000 m3 of Arsenic impacted material.Through much of the period of 1941 to 1970, Con Mine treated their refractory arsenopyrite ore through the use of an Edwards Heath roaster. With mounting environmental pressure and through Canadian governmental studies during 1950 to 1970, attention was directed to the Arsenic Trioxide material being collected by two Doyle scrubbers on the Con’s roaster stack. In 1970, the roaster was decommissioned leaving the resulting Arsenic material in two containment areas on surface.As a result of Con Mine entering into remediation in 2004, the Con’s autoclave, commissioned in 1992, was dedicated to the immobilization of high impacted Arsenic material through the combination of excess Iron under high temperature and oxygen overpressure. Examined, herein, is the history and chemistry of the Con Mine autoclave as well as the two stages of chemistry for the Water Treatment Plant used to remove arsenic, heavy metals and WAD cyanide from tailings water. Simplified capping plans of the tailing containment areas and a high arsenic impacted area are also presented.INTRODUCTION TO CON MINECon Mine (Con) is situated just south of the City of Yellowknife in the North West Territories (NWT) Canada and is bounded locally by Yellowknife Bay (North Extension of Great Slave Lake) to the east and Kam Lake to the west (Figure 6). The discovery of gold at Con was made in 1934 and mineral rights were acquired by Consolidated Mining and Smelting Limited (Cominco) and Falconbridge soon thereafter. Nerco Minerals Limited (Nerco) took control in 1986 and in 1993, was subsequently sold to, Miramar Mining Corporation which in turn was purchased by friendly takeover involving Newmont Mining in November 2007 as a result of acquiring the Miramar’s Hope Bay project. Con’s underground operations ceased in September 2003 and have since entered into the remediation of the site. The current surface lease holdings are about 340 Hectares (Table 1) which sits on top of the Archean-aged Yellowknife Greenstone Belt."

Jan 1, 2009

By Adam Zagorski, Rusty Lucido, Curt Scheyhing

"The current California Department of Transportation (Caltrans) practice based on AASHTO LRFD Bridge Design Specifications is to use the O’Neill and Reese method (FHWA, 1999) for calculating the side resistance and base resistance of Cast-in-Drilled-Hole (CIDH) piles / drilled shafts. In this calculation, end bearing is typically neglected for piles constructed using a wet method due to questionable reliability of end bearing resulting from soil disturbance and inadequate cleaning of the base. Pressure grouting below the tips of drilled shafts in cohesionless soils has long been used worldwide to provide reliable end bearing capacity, but for decades it was relatively unused in this country. It has been used increasingly in the United States over the last decade. Before this project tip grouting has not been utilized on or accepted by Caltrans to maximize piles end bearing capacity. This project proved that tip grouting to mobilize reliable base resistance can be successfully implemented on a full-scale bridge project requiring over 350 large diameter shafts.For the Gerald Desmond Bridge Replacement Project, Shimmick/FCC/Impregilo, JV utilized a temporary Oscillator casing to the full depth to install CIDH piles. Piles were constructed by the wet method and then pressure grouted below the pile tip. A tip grouting procedure for these large diameter shafts was developed and tested to specifically address the geology and constraints of the project. This procedure was then proven during the Load Testing of test piles during the Test Shaft construction phase of the project. Tests showed a minimum reliable base resistance of 150 ksf could be mobilized in very dense sand at a downward movement of 5% of the pile diameter for piles ranging from 4.9 to 8.2 feet in diameter. By tip grouting, the length and diameter of the piles were significantly reduced."

Jan 1, 2017

By EFFC/DFI Concrete Task Group

Concrete technology continues to advance rapidly and modern mixes with five components – cement, additions, aggregates, (chemical) admixtures and water – often have characteristics which differ significantly from the older three component mixes – cement, aggregates and water. Recent trends have favoured higher strength classes and lower water/cement ratios, resulting in greater dependence on admixtures to compensate for reduced workability and to meet the (often competing) demands for workability in the fresh state and setting time. The application of testing methods which reflect the true rheological properties of the concrete has not developed at the same rate as the mixes themselves and it is still not uncommon for the slump or flow table test to be used as the only acceptance test for fresh concrete.A joint review of problems in bored piles (drilled shafts) and diaphragm walls cast using tremie methods by both the European Federation of Foundation Contractors (EFFC) and the Deep Foundations Institute in the United States (DFI) identified a common issue. The review determined that many of the problems were caused by (or in part due to) the use of inadequate concrete mixes with inadequate workability, or insufficient stability or robustness of the mixes. It further identified the primary causes as inadequate concrete specifications and inadequate testing procedures. The consequences of these problems are often significant and it has been recognised that spending more time and money on getting the concrete right is the most cost effective approach.A joint Concrete Task Group was set up by EFFC and DFI in 2014 to look at this issue and this guide is the output from that Task Group. A research and development project, funded by the Sponsors of this guide, is being carried out by the Technical University of Munich in conjunction with the Missouri University of Science and Technology. This project includes desk studies, laboratory testing, and onsite testing at worksites in Europe and the US. The research work will be completed during 2016.

Jan 1, 2016

By A. Grimod

Rockfall drapery systems are commonly used as a simple, fast and cheap measure against the rock falling trajectories affecting very steep slopes. The system basically consists of a steel mesh, which is held on the top edge with a longitudinal cable fixed by means of a suitable number of anchors. The effect of this kind of intervention is to control the falls of the rocks, which are driven toward the bottom with slow velocity, or are stabilized on place. It can be used on any kind of slope to protect sensitive target in the mining industry, roads and railways, and inhabited areas. The falling blocks, typically smaller than 0.6 - 1.0 m in diameter, pile up into a trench (or into a ?pocket of mesh?) at the bottom. In comparison to other types of rockfall interventions, the simple drapery is cheaper, and its maintenance is easier, but on the other hand it cannot be considered the remedy for shallow instabilities, because it can only mitigate the effect of the falling trajectories. The design of simple draperies requires the analysis of several factors like the slope features (height, gradient, morphology), the geological and dynamic features (nature of the ground or rock, type of instability, erosion problem, blocks size), the environmental condition (presence of vegetation, aesthetical problem), the installation problem (accesses to the slope, safety for the workers, safety for the surrounding areas) and finally the performance required (temporary or permanent intervention, required maintenance, cost). Finally the most problematic design-step is the choice of the suitable mesh, the top longitudinal cable, and the top anchors type. Because of the highly variable nature of rockfall behaviour these structures cannot be standardized, but they have to be analyzed and designed for each case. Maccaferri has developed a new software application (MacRO 2) has a practical tool to define the mesh and the related supporting structure composed by up-slope cable and anchors. The software, based on the approach proposed by Muhunthan B. et al. (2005), allows designers to verify the top longitudinal cable, the anchors, and the mesh drapery, and to plan for maintenance procedures. Even if the method seems quite simple and rough, it is effective and lets the designer correctly foresee the materials and the geometrical features to be used on the interventions. This paper analyses the condition for the simple drapery installation, the main steps for the calculations, and it will present a case study in a U.S. mine. Nevertheless, even if the software allows a quick and simple calculation approach, onsite observations are always recommended in order to achieve a good design, with the ultimate goal of protecting property and human lives.

Aug 1, 2013

By G. B. Shea, R. A. Cattell

This resume of the work of the Petroleum and Natural - Gas Division of the Bureau of Mines for the fiscal years 1940 and 1941 is the second of a series. of progress reports . It brings forward from the 1939 annual report information on the course of activities of the division in carrying out its objectives of increased conservation and better utilization of petroleum, natural gas, and related resources through a coordinated program of research and fact - finding . It discusses, also, special assignments. executed for other Government agencies, which in recent years have constituted a considerable part of the division's work ." . In the present national emergency, in which petroleum is so essential , many of the Bureau's research activities bear directly on the availability, conservation, and use of petroleum for national defense . Accordingly, during the past year attention has been focused for the most part.on.problems associated with the needs of national defense . Several long-time researches , which in themselves are potential sources of desirable knowledge , were judged to be of secondary importance under present conditions and accordingly were suspended . Studies also were oriented in line with rapidly changing conditions to meet the demand for accurate findings on short notice . The Petroleum and Natural - Gas Division has experiment stations at Bartlesville , Okla . , and Laramie, Wyo . , a field office at Dallas , Tex . , and a field office and laboratory at San Francisco , Calif . It also operates the Government helium plant near Amarillo , Tex. In addition to the helium operations , some of the petroleum and natural - gas research activities are conducted at the Amarillo plant .

Feb 1, 1942

By David L. Shearer

INTRODUCTON James Howden first secured an order for two Service Tunnel Boring machines in November 1986. These Tunnel Boring machines were 5.7 and 5.4 metres in diameter and the full length including back up was 215 metres. Manufacture commenced in December 1986 at the Glasgow factories of James Howden & Company with the deliveries to site of the machines in September 1987 and March 1988 respectively. In December 1987 two further orders were secured for the land running tunnels at 8.7 metres diameter. This paper presents some of the challenges in building tunnel boring machines for the Eurotunnel project between Britain and France. The general specifications of the Tunnel Boring machines and length of drives are shown in Appendix 1. DESIGN PARAMETERS The specification given by the Consortium TML on behalf of their client Eurotunnel cleary indicated that cutting of the face should be concurrent with the building of the precast concrete lining rings. In order to do this a telescopic machine was thought to be the best solution. Ground conditions were described as chalk marls of homogeneous nature with the possibility of friable areas and some revelling. A shielded type TBM with open cutter head was chosen together with a telescopic section and a rear

Jan 1, 1989

By R. C. Neavel

One of the most important requirements to be met by any coal producer is delivery of size consists tailored to specific applications. Generally these specifications include a minimum as well as a maximum size limit. The customers of a major Indiana coal producer noticed that some shipments of sized coal contained a large proportion of undersize pieces. Also, in these shipments, the pieces which remained within the specified limits were cracked and, when handled, crumbled readily. The producer, certain that these shipments had been properly sized at the tipple, suspected that degradation had occurred in transit. The Indiana Geological Survey was requested to examine the coal from one of these shipments to attempt to determine the cause of breakage. Two basic facts about coal and coal seams led to the employment of petrographic techniques in this investigation. First, all coal seams consist of accumulations of diverse organic and inorganic constituents; and second, most coal breakage, either desirable or undesirable, can be attributed to the inherent weakness of some of these constituents or to poor adhesion between certain constituents. Analyses of degraded coal Sampling: Samples were secured from 2 stock piles of 2-by 4-inch coal in a dealer's yard. The coal in both piles had received the same treatment from mining to storage, although it had been mined and shipped on two different days. The size consist of one pile, however, appeared smaller than that of the other. The sample from the degraded pile is referred to as the slack sample, and the other is called the unslack sample. Size analyses: In order to determine the actual size consist, the samples were screened, with a minimum of rough handling, on square 2-inch, 1-inch, 1/2-inch, and 12-mesh screens. It is assumed that 100 percent of the 2-by 4-inch coal is retained on a 2-inch round screen at the tipple. Analyses of several loads at the tipple indicate that approximately 26 percent of the 2- by 4-inch coal, 100 percent of which was assumed held on a 2-inch round screen, passed through a 2-inch square screen. Twenty-six percent may be taken as the normal difference between round and square screens. Results of the analyses of stockpile coal are shown in Table 1. Cumulative percent versus size are plotted on a Rosin-Rammler chart as Figure 1. Both samples approximately follow normal size distribution; this indicates that breakage is not size preferential and also that the samples are representative of the stockpiles. Although both samples exhibit the same general size distribution, the median size of the slack sample is considerably smaller than that of the unslack sample. Fifty-five percent of the unslack sample was undersize (29 percent greater than the normal 26 percent difference), and 83 percent of the slack sample was undersize (57 percent greater than the normal 26 percent difference). Both piles contained a greater percentage than normal of undersize coal; this indicates that they were both affected by degradation, but to a different degree. Bedding-plane analyses: Coal, because of its laminated nature, will break preferentially along bedding planes, especially where adjacent constituents are poorly cemented to each other. Subsequent breakage perpendicular to the

Jan 1, 1961

By F. Samimi Namin

During the process of developing surface or underground mines, some sites are considered for dumping of surface soils, while others are applied to reclaiming surface and waste disposal. For each kind of overburden, whether it be waste rock, low-grade material, or process tails, a separate storage site is considered so that it becomes possible to transport or recover the overburden separately. Decision-making must be completed by means of a selection process which takes into account the best methods of alternative sets in order to achieve these goals. This decision- making involves many parameters that are inter-related in that changes in some parameters affect the others. There are many methods of decision-making, however, Fuzzy Multi-attribute Decision-making (FMADM) and its functions are studied in this paper. The advantages of this method lies in its theoretical background, formulation, revising capability, unlimited alternatives, and consideration of the counteraction of the different parameters upon one another.

Jan 1, 2007

By Basilio Giurgola, Jeremiah M. Jezerski, Filippo Azzara, Federico Bonaiuti, Russell H. Lutch

The Northeast Boundary Tunnel Project consists of a 23 ft diameter, 27,000 ft long, CSO tunnel, multiple underground connections, and significant surface works within an urban corridor. The NEBT alignment depths range from 60 to 140 ft and includes seven shafts ranging in depth from 77 to 155 ft with diameters varying from about 19.5 to 56 ft, some as in-line connections and others required adits for connection to the main tunnel. This paper focuses on the design and construction of two major underground connections which are the First Street Connector Tunnel and the Mount Olivet Road Diversion Sewer.

Jun 13, 2023

The Department of Mineral Resources has a statutory responsibility for mine site environmental management and control in New South Wales. The Department is focusing on an environmental management systems (EMS) approach, as a management tool to achieve æbest practiceÆ outcomes both within our own organisation and on mine sites. One of the DepartmentÆs tools is environmental risk assessment and management which incorporates the Mining, Rehabilitation and Environmental Management Process (MREMP). The MREMP was introduced many years ago in order to integrate the activities of key stakeholders who may have a material interest in the mine. The MREMP provides an ideal mechanism by which ædue diligenceÆ requirements and environmental management programs can be integrated into mining operations and lead to a sustainable post-mining land use.

Jan 1, 2002

By Lloyd A. Morley

This final report concludes the documentation under Grant G0155003 and details research not covered under foregoing report volumes. The first chapter lists all other reports. The following chapters are divided into three major research tasks: Continuous Safety Monitoring Systems, Battery and Battery-charging Safety, and Mine Power System Transients. The monitoring chapter discusses the prediction of power-system failures. The battery chapter details work on battery-box stresses, battery chargers, and the elimination of electrocutions. The final chapter covers transient instrumentation, distribution transients sources and suppression, and utilization transients on mine power systems.

Jan 1, 1981

By K. C. Garner

The visit reported was made with support from the 1997 J.C. Boyle travelling scholarship. The management and control of hazardous gases released into the underground environment are an integral part of coal mining. The power-generations stations at Appin and Tower collieries, with a combined electrical output of 94 MW, have been operating for some time and have demonstrated a technology that is able to exploit the available gas fully. Contributory factors have been the development and introduction of directional drilling techniques, pre- and post-drainage of coal, relatively high seam permeability, a high gas content of the worked seam, high production rates and a willingness to embrace new ideas and technology

Jun 21, 1905

The common approach of designing blasts on a trial and error basis is quickly coming to an end. When utilizing the full scale blast environment, trial and error can quickly become cost prohibitive and leaves much to be desired in terms of true blast diagnostics. In these situations testing is usually only continued until a perceived improvement is achieved and when the gross undesirables in blast results are removed. This does does not preclude, however, that further improvements of up to 100% or more can not be obtained.

Jan 1, 1991

By R. T. Richins

Coeur d'Alene Mines Corporation (CDE) is a precious metals mining company. The company's three mining operations are located In Nevada and Idaho. Collectively, these mines (Rochester in Nevada, and the Galena and Coeur In Idaho) produced about 61,000 ounces of gold and more than 7.5 million ounces of silver in 1991. The company is currently planning the development of two major properties; the Fachinal gold-silver project in Chile and the Kensington gold project near Juneau, Alaska. Fachinal and Kensington hold encouraging potential to significantly expand CDE's gold production during this decade. The permitting process for these two distinctly contrasting environmental settings, project design requirements and regulatory/political circumstances provide the basis for a comparative analysis of licensing and permitting requirements, timeliness of the permitting process and costs in the U.S. and Chile.

Jan 1, 1993

By Richard J. Lund

Stock piling-and by that I mean well-organized stock piling on a substantial scale-is almost as old as the hills themselves. It was back in early Biblical times, as recounted in the Book of Genesis, that Joseph was charged by Pharaoh with the responsibility of stock piling food during the seven years of plenty to guard against the seven subsequent years of famine that were revealed by the Pharaoh's dream. And this same policy of storing up food or materials to provide for future anticipated emergencies can be traced repeatedly down through the ages. So our own efforts are anything but new. Our modern concept of stock piling-the purchase and storage of strategic materials to assure supplies needed in time of some future war- stems from our experience in World War I. In 1920, the War Department was charged by Congress with the responsibility of procuring all War Department supplies and mobilizing industry in the event of another war. During the two decades that followed there were many authoritative studies made of our deficient mineral problem, all of which pointed out the urgent necessity of stock piling certain strategic materials as a reserve against future war. One such study, made in 1925 through the combined efforts of the Mining and Metallurgical Society and the AIME, was done at the ex- press request of the War Department. Eight years later another more de-

Jan 1, 1949

By E. D. Gardner

From the standpoint of tonnage and dollar value copper is the most important nonferrous metal mined in North America. The opening of copper mines has had an important bearing on the development and settlement of many sections of the continent. The prosperity of many of the mining States or provinces depends directly upon the copper-mining industry. Normally, about 35,000 men are employed in the copper mines, mills, and smelters of the United States. The United States is the most important producer of copper among the nations; more copper is mined in North America than in any other continent, and for many years the United States alone produced about half of the copper of the world. During the last 10 years increasing production in South America and Africa has reduced the relative importance of North America and the United States.

Jan 1, 1938

By John E. Trombly

System objectives and design criteria for an in-mine visual personnel paging system are discussed. Display technologies are evaluated and tradeoffs leading to display selection are described. The prototype dispatcher's console, battery/receiver box and visual display assemblies are functionally described. The report includes circuit descriptions, schematics, parts lists and equipment cabinet drawings for the three assemblies. The report concludes with an estimate of the manufacturing cost for each assembly.

Jan 1, 1975

By Y. V. Vasylchuk

This paper presents an algorithm for optimizing the classification of surface mine material subject to excavating constraints. High-resolution expected profit models are input and optimized to classification maps subject to site-specific rectangular excavating constraints. This optimization problem defies traditional closed-form analytical solutions; a practical heuristic algorithm has been developed to quickly determine the optimal final destination for the material subject to realistic constraints. The optimization is fast and generates results that achieve up to 98–99% of the total expected profit achieved with free selection. This algorithm provides a fast viable option for practical application in short-term grade control and in managing multiple realizations in long-term resource estimation.

By Y. V. Vasylchuk

This paper presents an algorithm for optimizing the classification of surface mine material subject to excavating constraints. High-resolution expected profit models are input and optimized to classification maps subject to site-specific rectangular excavating constraints. This optimization problem defies traditional closed-form analytical solutions; a practical heuristic algorithm has been developed to quickly determine the optimal final destination for the material subject to realistic constraints. The optimization is fast and generates results that achieve up to 98–99% of the total expected profit achieved with free selection. This algorithm provides a fast viable option for practical application in short-term grade control and in managing multiple realizations in long-term resource estimation.

By Joseph C. Gillen

This paper discusses the design, construction, and performance of the support of excavation system used at The Atlantic Building jobsite. The support of excavation system had to be adaptable to the different conditions surrounding the site. These conditions included support of four historic building façades, including the nine-story Atlantic Building, as well as support of three historic row-houses along two walls. Directly adjacent to the site is the historic Ford?s Theatre and townhouse. Across a 15? alley is the American Immigration Lawyers Association (AILA) Building, and across a 30? alley is the Federal Election Commission Building and another ongoing excavation. Of historical note, these two alleys were the escape route for John Wilkes Booth following his assassination of President Lincoln. With the excavation being 53? to 58? deep, the system included driven and drilled soldier piles, drilled bracket piles, and two modified tangent walls. The bracing included tiebacks, corner braces, wales, cross lot struts, and a specially designed support system for the nine-story façade. The footprint of the excavation included 12 corners and all alleys and streets were to remain open during construction. The performance requirements for system movement at Ford?s Theatre and AILA Building were ½ inches in the horizontal direction. The modified tangent walls were used in these areas to provide stiffness. The soil conditions at the site were fill material on top of a shallow, sandy, silty, gravel layer on top of a deep layer of soft organic silt and clay. Below the silt and clay layer was fine sandy material at the subgrade.

Jan 1, 2006