Search Documents

By Joel Moskowitz

A new office complex is being constructed within 25m of the Hudson River in New Jersey. The project, about 140 m by 100 m, will include 4 basements under the entire footprint. The perimeter was to be secured by a 0.8 m thick diaphragm wall, laterally supported by high capacity tieback anchors to rock. Columns were to be supported on footings or piers to rock at a nominal bearing pressure of 3.8 MPa at depths up to 17m. Although some variation in rock quality was observed in borings, a substantial vertical seam of weathered and/or decomposed rock, 1 to 2 meters wide by as much as 8 meters deep, was encountered during construction necessitating field redesign. In some locations the seam dipped below more competent rock. Footings were redesigned for support on drilled caissons, or soft rock was excavated and replaced with concrete necessitating a reduction in bearing pressure of the footings by one half.

Jan 1, 2002

By A. Rai

"This paper provides an overview of the current use of auxiliary ventilation product and the challenges with limited air quantity in dead-end entry or working face. The PVC low frictional factor, low physical constraint and minimum leakage ventilation duct was development with ""made in US and used in US"". The PVC duct development covering operational and total cost of ownership with on-going success will be presented. This paper will discuss mine sites using new PVC vent duct underground and the results from operational and technical side making a difference. INTRODUCTION The Turquoise Ridge Joint Venture (TRJV) is located in northern central Nevada, and is situated within the Basin and Range province, near the northeast end of the Osgood Mountains (see Figure 1). The TRJV mine consists of typical Carlin type- gold mineralization characterized by low strength rock of altered limestone’s, siltstones, and mudstones. The weak nature of the ground facilitates the underhand cut and fill mining methods [3].Mining Method; Underhand cut and fill : The mine uses underhand cut and fill method which has 12’x12’ top cuts and several different size undercuts. The ore body is accessed off of a secondary development heading, utilizing a heading with a cross section of 14W x 14H or 15W x 16H configuration. In the wider and more massive zones, two headings in a production panel may be worked at any one time. Drift round lengths are determined by the type of drilling machine being used. An example of a typical topcut and associated undercut layout is shown in Figure 2. SECONDARY / AUXILIARY VENTILATION IN UNUNDERGROUND METAL MINES The auxiliary ventilation system provides the required air volumes at the face of dead-end developments and production workings, which in many cases may be considered as the primary method of assuring that the air quantity and quality standards in these working areas are satisfied. The Auxiliary fans and ducting systems are usually the primary means of delivering the required air volumes to the face of dead-end developments and production workings. Both centrifugal and axial-flow fans are used in underground auxiliary ventilation systems, usually electric powered. The internally direct driven axial-flow fans tend to be more popular because of their compactness and adaptability to staging. The most commonly used materials for ridged tubing are coated steel, alloyed steel, fiberglass and resin. Flexible (collapsible) ventilation tubing is also used and is usually made from neoprene-coated or nylon material. To add stiffness and reduce collapsibility these fabric ducts can be formed over a steel spring frame. A very important factor in the design of an auxiliary ventilation system is to minimize leakage and reduce the frictional pressure losses along the auxiliary ducting systems by minimizing their friction factors (K)."

Jan 1, 2015

By Cadman S. J

( The central part of the Gippsland Basin is surrounded by existing major Petroleum accumulations and although six exploration wells have been drilled in the area, none are significant petroleum discoveries. Post drilling analyses indicate that the wells were drilled off structure due to the presence of high-velocity Miocene channels. These channels contain carbonates of significantly higher interval velocity than the surrounding sediments. Problems with seismic interpretation were thus encountered in the development of prospects in the central part of the Gippsland Basin as part of a BMR prospectivity study. The seismic interpretation problems associated with the Miocene channels are two-way time pull-ups at the underlying top of Latrobe Group and deeper levels on the seismic sections. Interpreted seismic sections passing through some of the exploration wells and the Miocene channels are presented to illustrate the configurations of these channels and the pullup effect associated with them. Two different methods of depth conversion were applied, one for the area below the high velocity channels and the other for the area away from the channel. The application of these two methods of depth conversion were found to be reasonably successful in correcting for the pull-ups caused by the high velocity Miocene channels. Mapping of the events near the top of Latrobe Group and near Base Lower L balmei seismic horizons has led to the identification of several potential structural closures. Further exploration efforts are necessary in this area to test these closures.

Jan 1, 1992

By Ian Holl, Adam Hempstock, Rickardo Welyhorsky, Niel Morrison

"The Victor Diamond Mine is located in the James Bay lowlands, 90 km west of the First Nations village of Attawapiskat. The project was the first of its kind in northern Ontario and was completed approximately 9 months ahead of schedule.The Victor Mine process plant flowsheet was designed to produce a 95 - 98% by weight diamond concentrate. Main processing steps include 3 stages of comminution, dense medium separation and proprietary x-ray technology for final recovery. Reagent consumption for this process is limited to flocculant, for thickening of fine processed kimberlite, and FeSi for the dense medium separation.The commissioning phase of the Victor Project was executed over a period of 6 months and commenced prior to substantial completion of construction. The approach used was to focus on and complete commissioning of the higher risk dense medium separation and recovery systems prior to construction completion of up stream systems.INTRODUCTIONThe development of the Victor Diamond Mine took place over a period of approximately 5 years and had a capital cost of CAD997 million. It was a greenfields project in an undeveloped region of northern Ontario, only accessible by winter road. Figure 1, below, displays the location of the project within Ontario.The main stages of the project included feasibility, environmental permitting, engineering, construction, and commissioning. At the onset of the engineering phase, the mine was scheduled to enter production in October 2008. Through a team effort between AMEC and DeBeers Canada, the schedule was advanced by 6 months towards the goal of project completion in April 2008. Production status was attained in January 2008, approximately 9 months ahead of the original schedule. This paper focuses on the commissioning aspects of the project and includes a less detailed discussion of the engineering stage."

Jan 1, 2010

CORPORATE SOCIAL RESPONSIBILITY CSR is about how companies manage the business processes to produce an overall positive impact on society. - Indentured work, sexual slavery, fair trade, organic growing, business ethics, environmental issues, ?Right to know -Right to decide?, AIDS activism, civil society - Balancing stakeholder issues - Government responses Who are the bad guys? Where are the threats?

May 1, 2010

By Raymond Rivera

El presente texto describe la evaluación desarrollada por INGEMMET donde se analiza el potencial de los depósitos minerales en el Batolito Andahuaylas, Yauri, así como el potencial de algunas zonas que presenten características geoeconómicas importantes, utilizando herramientas geológicas como geocronología, isótopos radiogénicos, geoquímica de rocas y sedimentos, petromineralogía y geología estructural.

Sep 12, 2011

A preliminary program dated April 25, 1974, was prepared for Development Engineering, Inc. (DEI) on research and development. for laboratory, field and other engineering studies on the disposal of retorted oil shale. This program was revised and published as a final document dated December 17, 1974. The document included discussions on the peculiarities of retorted shale materials to be investigated and discussions of the various laboratory and field tests which would need to be conducted to define their physical and chemical properties. The proposed research and development program was divided into eight work phases as follows: I Program Development. II Exploratory Laboratory Tests on Old U.S.B.M. Retorted Shale. III Laboratory Tests on Pilot Plant Retorted Shales, IV Laboratory Tests on Retorted Shale from the Semi-Works Plant, Field, Test Plots and Ponds. V Field Compaction Tests. VI Infiltration Pond Tests. VIII Final Report.

Jan 1, 1975

By Clay Haynes

In 2005, Black & Veatch Corporation began designing a raw water conveyance system for San Luis Obispo County from Lake Nacimiento to the city of San Luis Obispo. The first element of the water transfer system will be a raw water pump station and lake tap. The wet well of the pump station will consist of a concrete lined shaft approximately 180 feet deep constructed in the very incompetent sandstone of the Vacqueros Formation. The lake will be wet tapped at approximately 172 feet below grade using a slurry earth pressure balance tunnel boring machine. The 48 to 72-inch finished diameter microtunnel will be approximately 500 feet in length. Construction is scheduled to begin in the winter of 2007.

Jan 1, 2008

By Sushil Bhandari, Amit Bhandari

Drilling and Blasting are core operations in a mine. They impact all the downstream operations and their costs. Digital technologies exist for optimizing both drilling and blasting for many years. However, these technologies have largely been non-integrated and non-real time. This gap results in sub-optimal drilling and blasting operations. Also traditionally focus has been on optimizing individual areas (drilling or blasting and subsequent subsystems). Industry has largely lacked real time or near real time integration available to the user in the field and in the office. In this paper, a case study is presented of a large global cement company using a cloud and mobile based platform across 17 of their mines consistently over a large number of users over a period of over two years. The use of a blast platform is detailed which include blast designs, blast data collection and the trends in terms of results. On the drilling side, this paper describes the ability to capture drill logs, plod reports etc. Also actual drilling information in the field using a mobile device and its real time synchronization with a blast designer to provide visibility of expected fragmentation and vibration levels based on the drilling done. Key parameters such as hole ID, design depth, actual depth, hole status, designed and actual charge (length and weight), designed and actual stemming length are captured. The case study also highlights the challenges in technology adoption and implementation in mining in drilling and blasting. Making drill and blast results predictable should be the desired direction. Also digital technology tool adoption has been seen at the biggest miners – not so much in mid-sized miners or drill and blast contractors. Benefits of this platform on the safety side are highlighted including predictions on safety parameters and appropriate alerts if blast safety parameter / clearance zones are not met. The safety parameters are made available visually to the operator using maps and / or on drone images. Future possible improvements in the digital technology platform at the site are also highlighted including greater possible automation.

Australian rutile and zircon concentrates are refined raw materials and not manufactured products. The composition and properties of the grains are therefore fixed by nature. Specifications and assay certificates should take this into account by eliminating unnecessary provisions which only increase the time and cost of analysis.INTRODUCTIONThe raw material from which Australian rutile and zircon concentrates are isolated is beach sand on the coast of New South Wales and Southern Queensland. The principal current operations are in an area between Sydney and Brisbane.The sands consist principally of quartz particles, but they contain from 1 per cent to 50 per cent of a mixture of heavy minerals, including zircon, rutile, ilmenite, monazite, leucoxenic grains, chrome spinel, chromite, garnets, corundum, topaz, brown spinel, olivine, epidote, clinozoisite, tourmaline, magnetite, hematite, and cassiterite. The major components are zircon (25 to 60 per cent), rutile (25 to 50 per cent), and ilmenite (5 to 50 per cent).The so-called leucoxenic grains are not a definite mineral species but an alteration product of which the major components are titanium oxides and silica in varying proportions.Primary concentration is by gravity, using spirals or various forms of pinched sluice (Pullar, 1962), the resulting concentrates being redressed on wet tables. During these processes, some of the lighter heavy minerals including leucoxene and impure rutile, which tend to degrade the final rutile and zircon concentrates, are eliminated.The separation of heavy minerals from each other is...

Jan 1, 1963

By H Bateman, I Cawrse, G Carnes, S Cawrse

In developing mineral resources, the focus typically centres on the management of identified social and environmental impacts and compliance with regulatory requirements. However, opportunities to protect and enhance the environment and communities are most effective in the planning and design phases. Achieving the objective of integrating sustainability considerations as an element of design decision making requires that the design criteria be technically sound, relevant to the project and applicable to desired design outcomes. This is particularly important for projects employing virtual teaming, where design engineers may be geographically dispersed and are unlikely to be familiar with site specific sustainability challenges and opportunities. This paper documents the approach taken by BHP Billiton to incorporate sustainability principles, objectives and guidelines in design criteria for the Olympic Dam Expansion (ODX) project. It describes the range of inputs used in defining sustainability objectives which interface in a framework that is dynamic and transferable to other mining projects and to engineering design in general. The Sustainability in Design Criteria document distils statutory requirements, corporate standards, lessons learned and leading industry practice into a single coherent framework that supports engineers to approach problem solving as a holistic and integrated exercise with a long term perspective. The framework also serves to improve linkages between internal stakeholders by fostering greater communication, collaboration and innovation to deliver more sustainable outcomes through the design process.

Jan 1, 2009

By B. J. du Plessis

Automation of the conventional grinding circuits of Palabora Mining Company (PMC) required that adequate instrumentation and a control system had to be put in place, after which extensive testing had to be done to evaluate different grinding control strategies. The objective was either to optimize the particle size from the grinding circuit, or to increase milling circuit throughput while maintaining particle size at existing levels. Prior to automation of the process as described below the circuits were controlled manually. No on-line information on cyclone feed densities, cyclone feed flow or cyclone overflow particle size was available. This type of control relied heavily on interpretation of the process parameters by the operator and on his ability to make informed decisions on what the set points should be. An integral component of the automation process was the installation of a SCADA package (SysCad SDX) for implementing the on-line control strategy. A self-correcting model for prediction of cyclone particle size was developed and implemented on the SDX. The model is calibrated using values from the particle size analysers while they are operational. If the particle size analysers choke or fail for any reason, the model continues to provide a good estimate of the particle size. This technique ensures that a continuous particle size indication is available compared to the intermittent reading from the instrument. The continuous signal allows particle size to be used as a process variable for control purposes. A strategy was developed and implemented which allows for the production of a controlled grind size from the conventional milling circuit to the flotation circuit. The grinding control strategy allows for the control of particle size from the individual cyclone overflows. This strategy allows the operator of the process to increase or decrease production rate by specifying a coarser or finer grind size required for flotation.

Jan 1, 2001

By P. Somasundaran, D. R. Nagaraj, Tarun Bhambani, P. Patra

Flotation separation and recovery of value minerals from ores containing fibrous silicate minerals are known to be quite challenging. Earlier studies have established that the metallurgical challenges (poor selectivity and recovery, high energy consumption, etc.) arise from the impact of the fibrous minerals (with high aspect ratio) on pulp rheology, which was found be rather complex. The complex rheological behavior of ore suspensions containing particles with high aspect ratio and its influence on flotation outcome are investigated in this study. Flotation tests and rheological measurements were carried out with both ores (containing fibrous minerals) and a model system comprising nylon fibers (chemically inert) added to a copper ore that had no fibrous mineral. These studies allowed the determination of contributions of physical properties of the fiber to pulp rheological behavior. Optical microscopy images of the fiber pulp indicated that the fibers entangled to form two levels of microstructures: two-dimensional (2D) aggregates under semi-dilute (< 20% solids) conditions and three-dimensional (3D) microstructures at concentrations > 30% solids. The yield stress (σ) values determined for the fiber pulp were logarithmically related to the volume fraction of the 2D/3D structures. The relationships developed here for different ARs showed that the yield stress of a flotation pulp changes with respect to shape, size, and the concentrations of the microstructures. Implications to the effects of such entangle networks on selectivity of flotation separation are discussed.

By L. Nell

Bateman, like other engineering contractors, carries out or participates in many studies of potential projects in the Minerals Industry. This paper aims to explain the contracting approach to feasibility studies as practiced by Bateman, particularly where this differs from a traditional mining company approach. A brief description is provided of the usual phases of a project and the types of estimate needed to proceed from one phase to the next. Possible organizational structures involving different forms of association between owner, contractor and consultants are then outlined. The bulk of the paper then demonstrates that the cost estimates prepared stem directly from the mining plan, metallurgical process design and engineering design philosophy. The steps to be followed in order to prepare a credible estimate which accurately reflects the design constraints are described. The importance and the methodology of carrying out value engineering and of preparing contingency estimates based on a thorough risk analysis exercise are then discussed. Financial modelling techniques are described briefly. The paper concludes with short summary case studies of two recent investigations of potential projects in Africa.

Jan 1, 1999

By Warren M. Mahan

A rotary kiln process was developed by the Federal Bureau of Mines to produce consistently an iron product containing 3 to 7 percent nickel. Cuban laterite and serpentine ores were smelted in a gas-fired batch-rotary kiln) 5 feet in diameter and 9 feet long. The metal contained 2 to 4 percent carbon, with little or no silicon, and could be produced on a large scale with modest capital investment. A total of 121 tests was run using this procedure. The tests were conducted with a maximum temperature of 2,625° F., using linings of firebrick containing 40 to 70 percent alumina. Slags in the kiln were acid to neutral. The material in each batch passed through three stages: (1) Sponge metal, (2) carburization, and (3) balling and meltdown. Half the tests were made while firing the kiln with atmospheric-temperature air; the remainder were fired with preheated air. Tests showed that preheated air decreased fuel requirements, dust losses, and reducing agent, and increased the capacity of the kiln.

Jan 1, 1960

By G. Thodos, W. F. Stevens

The point-source function introduced by Horner&apos; us a solution to the general unsteady-state equation for the flow of fluids through porous media has been utilized to calculate pressure profiles for adjacent wells as a function of time. By trial and error, the time at which the pressure waves meet to cause interference can then be calculated. For this calculation, the time of interference is arbitrarily defined as that time when both pressure waves exhibit a pressure decrease of 25 psi ar the same point within the formation. To illustrate the method, an example involving two adjacent wells producing at different rates has been worked out and is presented in detail. INTRODUCTION The initiation of production of a new well is usually accompanied by pressure drawdown measurements in order to establish the extent and characteristics of the formation. The interpretation of such pressure drawdown data is based on mathematical developments involving a single well in an infinite reservoir. If more than one well is present in a reservoir, the possibility of interaction between wells exists. Therefore, care must be taken in interpreting the pressure drawdown data. It becomes important to be able to determine when this interaction, or interference, becomes significant. This paper presents a method for the prediction of the approximate time of interference between two such adjacent wells. The basic differential equation describing the pressure distribution existing during unsteady-state flow of a slightly compressible fluid has been solved by Hor-ner.&apos; for a constant production rate from a circular homogeneous reservoir of infinite extent. The solution utilizes the point-source function to define the pressure at various points within the formation as a function of time. The resulting expression is: q = production rate, STB/D ,;= formation volume factor, dimension-less µ = fluid viscosity, cp k = formation permeability. md H = formation thickness, ft C - fluid compressibility, psi&apos; F = formation porosity, dimensionless R = distance from centerline of well, ft T = production time, hours Ei(—u) = Ei-function of U Eq. 1 may be used to calculate the pressure profiles generated during production from a single well in an infinite reservoir.

By Michael J. Atwood

Many buildings in Boston are founded on untreated wood piles, which can deteriorate and lose their structural capacity if groundwater levels are lowered below the tops of the piles, exposing the wood to air in the unsaturated soils that surround the piles. The problem of wood pile deterioration due to lowered groundwater levels in Boston first became evident in 1929 following discovery of rotten piles beneath walls of the Boston Public Library building. Repairs to reconstruct the library building?s wood pile foundations were made in 1930 using pit underpinning methods. Today, more than 80 years later, the subsurface conditions beneath several of Boston?s historic neighborhood areas continue to be plagued with low groundwater levels - regrettably resulting in ongoing deterioration to the wood piles that support some of Boston?s oldest and most beautiful buildings. Pit underpinning is still recognized as the preferred approach to repair wood piles and restore uniform foundation support beneath the impacted buildings. This paper provides a brief historical review of the land filling in Boston through the early 1900s that led to the use of wood piles as building foundations. Also discussed is the impact that groundwater level can have on the long term performance of wood pile foundations and the pit underpinning procedures used to reconstruct decayed wood pile foundations in 1930 beneath the Boston Public Library, and today beneath some of Boston?s oldest buildings. Also included are discussions on engineering controls and permitting requirements that help ensure safety and protection to the workers and buildings during underpinning, and some procedures being used to supplement and improve the loading capacity of the reconstructed foundations and facilitate construction of new useable below-grade space.

Jan 1, 2011

By W. G. Brunner

The slurry wall technique has undergone an evolution from its invention to its today’s status. In the early stages slurry walls were built with cable grab, later on with much stronger hydraulic grab and last but not least with the use of the cutter technique. The cutter allows thick walls with high verticality to extreme depths through hard soil and rock formations. With the rising demand of the construction of watertight diaphragm walls different joint systems have been developed. In addition to the rapid development of excavation systems it was necessary to improve slurry treatment and desanding plants, especially in conjunction with high performance trench cutters. Deep mixing methods can be used economically for the construction of cut-off or excavation support walls where other systems such as traditional soldier beams and lagging walls would yield unsatisfactory performance, where the installation of vibrated or driven sheet piles could cause vibration induced settlements and where concrete diaphragm walls would be time consuming and expensive. The new CSM method can largely replace the more conventional single or multiple auger methods of soil mixing or jet grouting. The cutter tool is similar to a cutter used in diaphragm walls or cut-off walls and is operated with a Kelly mounted on a drilling rig or rope suspended on a crane jib or mast of a base carrier. With this system much deeper walls can be installed and even hard soil layers can be penetrated.

Jan 1, 2007

By William M. Gleason

The war in Vietnam stretched into another decade, an American President was at the brink of impeachment, the earth was given its own day, twin tower monuments of American ingenuity were completed in New York and would stand high above the Manhattan skyline for 31 years. Inflation, oil shortages, low commodity prices and America’s 200th birthday were part of the decade — it was the 1970s. For the mining industry, the demands of the decade would be high and the challenges would be significant. Because of the many challenges that lined up in front of it, the mining industry was forced to work smarter and more efficiently. The industry also expanded its borders in search of new resources and struggled along with the rest of the world through a fuel crisis, inflation and a recession.

Jan 1, 2007

By O. Peters, D. Lascelles, R. Caldwell

Ageing tests on a crushed Cu-porphyry ore were conducted to assess the impact of sample oxidation on flotation performance. The objective of the testwork was to simulate ageing of ore that would be blasted through block caving but not milled for possibly several months. Ageing was performed in specially designed columns, using site and deionised water to keep the samples moist over the entire ageing period. Samples from each ageing interval (0, 0.5, 1, 2, 4, and 8 months) were examined for physical and metallurgical changes resulting from the ageing process through chemical analyses, size analyses, and batch flotation tests.

Jan 1, 2009