Search Documents

Council for 1999/2000 President M.H. Rogers President Elect Dr L.A. Cramer Vice Presidents Senior A.A.B. Douglas Immediate Past President J.R. Dixon Junior S.J. Ramokgopa Honorary Treasurer J.A. Cruise

Jan 1, 2000

By C. L. Brown

"INTRODUCTION The heavy loss of life from mine fires in some coal mines recently has focused attention on the importance of maintaining reliable communication systems between the active working sections of mines and the surface. A study of conditions following disasters in mines indicates that in several instances lives could have been saved if telephone communication had been available. Communication systems were not installed in some of these mines where disasters occurred, and in other mines they were installed in such a manner as to be rendered useless following a mine explosion or fire. Lives have been lost because of the inability of the rescue crews or persons di-recting the rescue to communicate with trapped men. Cases are known where many lives might have been saved had it been possible to give instructions for escaping or for location of barricades.More than 500 major disasters in which 5 or more lives have been lost have occurred in mines in the United States. The total number of lives lost in these disasters has exceeded 13,000. Some of the victims died instantly; but for many it was hours and in some instances days before death occurred. Evidence found in recovery operations following some of the disasters indi¬cates that many died needlessly because of the lack of suitable means of communication between the underground working areas and the surface.A localized gas and dust explosion in a coal mine in 1930 resulted in the death of 82 men; 2 were killed outright by the force of the explosion, 6 by a combination of burns and afterdamp, and 74 by afterdamp. About 140 men escaped or were rescued following the explosion, Of these, 119 escaped with little or no assistance, 2 were rescued promptly following the explosion, and 19 were rescued from behind a barricade. Seven bodies were re-covered from behind an ineffective barricade in another place; subsequent investigation proved that these men might have been guided to a safe location had an effective communication system been available."

Oct 1, 1946

By J. C. Edwards

The National Institute for Occupational Safety and Health (NIOSH) implemented a real-time neural network system which can discriminate mine fires from nuisance diesel emissions as part of an atmospheric mine monitoring system in NIOSH?s Safety Research Coal Mine. The real-time response of a neural network to fire sensor outputs was demonstrated for coal and belt combustion in the presence of diesel emissions. The fire sensors consisted of an optical path smoke sensor, a carbon monoxide (CO) sensor, and two types of metal oxide semiconductor (MOS) sensors. The real time neural network was trained with coal, wood, and belt fire experiments with and without diesel emissions background. The trained neural network successfully predicted mine fires with these combustibles in the smoldering stage prior to the onset of flames.

Jan 1, 2005

SME-AIME Fall Meeting and Exhibit

Jan 9, 1979

By G. J. Hearn

between particles in the classifying region is then

Apr 1, 1995

By Zhiyun Li

Room temperature infrared reflection spectra of 2 n-type homo-epitaxial epifilms have been measured in the work. The effect of the refractive index on the determination of layer thickness using traditional calculation measurement is studied and some improvements have been added to the measurement to improve the accuracy and stability of the measured results. Results of the improved method have great agreement with the results from SEM and both variance and mean relative error decrease an order of magnitude.

Jan 1, 2010

By S. R. Gilbert, C. O. Bounds, R. R. Ice

"Many ores are upgraded to produce auriferous sulphide concentrates (principally pyrite) which are not amenable to direct cyanidation. Often these refractory gold-bearing concentrates contain undesirable elements such as arsenic, antimony, etc., which present environmental and/or processing problems. The pretreatment techniques most often considered for processing these concentrates prior to cyanidation include roasting, pressure oxidation, chemical oxidation, pre-aeration, and recently, bacterial oxidation. In this paper, the technical performance and economics of bacterial pre-oxidation vs the classical roasting approach for treating a specific auriferous pyrite concentrate are compared. The results provide flow sheets, preliminary operating and capital cost estimates, and rates of return for the two processes and demonstrate the potential advantages of bacterial pre-oxidation. IntroductionThe increased attention that gold has received in the last ten years has prompted mining companies to look for lower grade orebodies. Many of these low-grade ores do not respond well to conventional direct cyanidation recovery techniques. As free-milling ores decline, gold is sought in refractory environments which, ultimately, drive up the treatment costs.There are a number of reasons for a gold ore to be termed refractory, most of which can be identified by thorough mineralogical examination. The mineralogical occurrence of gold can, to a great extent, impact the method by which the ore is treated and, consequently, the capital and operating costs. Gold in a refractory ore can often occur as discrete particles locked in a host of silicate or carbonate gangue, or associated with sulphides or sulphosalts. Depending on its particle size, gold can be liberated and recovered by mechanical size reduction such as regrinding. This approach is most effective for gold in the 10 - 50 micron range. Gold can also be associated with clay, iron hydroxides, or other minerals which tend to coat the gold surface and inhibit the penetration of the cyanide solution, resulting in poor plant recovery. Because of their resistance to cyanide dissolution, gold tellurides and other refractory gold minerals are also responsible for losses to the tailings. For these reasons, it is paramount that the mineralogical occurrence of the gold be thoroughly and accurately determined before selecting a final process flowsheet."

Jan 1, 1988

By S. J. Ramokgopa

The development of the modern State and the growth of capitalism involves a complex process of interaction between cross-cutting structural dimension: first between politics and economics and, second, between market and hierarchy. Central to such developments are political economies of scale. Mineral specialization in the Third World developed within the framework of an international extension on oligopolistic structure of the advanced capitalist economies of Western Europe and North America. Up to the late 1960s, the world mineral and metallurgical industry was closely controlled by a handful of Western mining and industrial groups. To the extent that, foreign control of the mining sector was seen in the Third World producing countries both as the essence of foreign domination and as its major symbol. In some newly industrializing countries, the State took a more direct role in tying the economy and society together. Central to this process was the growth of large-scale finance capital. From early 1959to the mid-1970s, metal consumption in industrial countries expanded well beyond their domestic mineral endowments. And a free access to Third World minerals was a major element of the economic dynamism of these countries throughout that period. With the change in the characteristics of international investment, Africa has become less important as an outlet for capital exports of European countries. Actually, the African continent now receives only a very minor share of direct foreign investments of Western enterprises. International political economy is concerned first of all with the relationship between the economic and political domains across territorial boundaries. Second, attention should be drawn to the role of the State as the focus of decision-making in a system of competitive States, that is in turn, interdependent with a trans-national market economy in which mining and metallurgy are essential activities that affect the politics of the State, and how this in turn, rebounds on the politics of the international system. Understanding the role of the State must go beyond the glib pronouncements on the ?national interest?. How, and whose interest, the ?national interest? is determined, is precisely the problem. This implies a third theoretical problem that must be addressed: the linkage between the domestic and international domains (or levels of analysis), given that political-economic processes clearly cut across the lines of political decision-making constituted by the institutional structures of the State. Situating the State and economic interests within this vast ?state-society? complex that we call the global order will be a crucial problem for any theoretical approach that involves mining and metallurgy.

Jan 1, 2002

By J. S. Peterson

Occupational noise-induced hearing loss (NIHL) has been recognized by the National Occupational Research Agenda (NORA) as the most common job-related disease in the United States. Roughly 30 million workers are exposed to excessive noise levels or toxins that are potentially hazardous to their hearing. The National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR)is investigating noise controls to reduce operator overexposures caused by haul trucks used in underground metal/non-metal mines. To identify the most significant contributors to the overall sound level, Source Path Contribution (SPC) analysis was conducted. Noise dosimetry and time-motion analysis were also conducted to quantify operator noise exposure. SPC analysis determined that, under high idle conditions, a source near a hydraulic pump mounted to the rear of the engine and the engine cooling fan were the major noise sources. The time-motion/dosimetry analysis showed that the operators accumulated more than 90% of their noise exposures while they were hauling ore to the dump site and traveling back to the load site unloaded.

Jan 1, 2012

By H. Simonsen

Risk assessment consists of a search for the answers to: ?What can happen? ?How likely it is that it can happen? ?What are the consequences if it does happen? Perhaps the most important aim of risk analysis is to predict the likelihood that a planned profit will be achieved over a given period of time. A typical risk model employed for this purpose includes a stochastic connection between the dependent variable of an expression that describes a process and independent variables represented as random quantities. The output will be a probabilistic distribution. The uncertainties in a planned mining operation include: ?Commodity market characteristics, particularly price ?Ore reserves and mineralogical composition ?Mining method ?Process performance ?Capital and operating costs ?Schedule duration ?Economic environment effects. The processes employed in the probabilistic estimation of a project?s outcome include both Monte Carlo simulations and simulations where variable correlation is considered important. The risk model, once developed and tested, provides a framework for a rational approach to risk analysis and the testing of alternatives.

Jan 1, 1999

By Andre Zingano

The objective of this paper is to study the effect of annulus thickness on the quality of resin mixture for fully grouted resin bolt. Pullout and mixture tests were made in underground coal mines for the following arrangements: (a) borehole diameter 1.14 in. (29 mm), and roof bolt diameter 0.75 in. (19 mm) with steel wire around the roof bolt; (b) borehole diameter 1.14 in. (29 mm), and roof bolt diameter 0.75 in. (19 mm) with no wire around the roof bolt; and (c) borehole diameter 0.95 in. (24 mm) and a roof bolt diameter 0.75 in. (19 mm) with no wire around the roof bolt. The mixture test in steel pipe showed that the best resin mixture is for borehole with 0.95 in. (24 mm). The arrangement (b) produced big voids around the bolt. But for the 0.95 in. (24 mm) hole, arrangement c, the mixture was the best. It was corroborated with the pullout tests results where there is a difference in grout stiffness: the 0.95 in. (24 mm) borehole is about 10 times higher than a borehole with diameter 1.14 in. (29 mm). On the other hand, for the cohesive strength the difference is not significant. Numerical models were built to simulate the pullout tests, and also to simulate the roof support at an intersection. Convergence at two underground intersections, consisting of an immediate roof with laminated sandstone, was monitored to evaluate the performance of the roof supports, using the 1.14 and 0.95 in. (29 and 24 mm) diameter boreholes (i.e. arrangements ?a? and ?b?). The convergence readings showed that the 0.95 in. (24 mm) borehole diameter resulted in a smaller, although it was not significantly different.

Jan 1, 2008

By Rudolf E. Greuer

The existing computer programs for the simulation of ventilation systems under normal ventilation conditions are reviewed and a suitable program for including the influence of mine fires is selected. New program parts are written for the consideration of methane productions in coal mines, heat and gas productions of mine fires, temperature and air composition changes in ventilation systems, and the ventilation forces resulting from the latter. Other program parts are provided for the detection of danger zones and reversed air currents and for the inclusion of recirculated air currents in the network analysis. Existing program and new program parts are combined. The resulting new program can be used for a multitude of assignments. It is designed for the practical ventilation engineer and should be applicable to all types of ventilation emergency plans, in particular mine fire plans. The organization of the program and its mathematical basis are described. A FORTRAN IV listing and several flow diagrams are included. Eight executed examples are discussed, input and output for these examples explained. Storage requirements and execution times are estimated.

Jan 1, 2011

By David S. Yang

The construction of Oakland Airport Roadway Project for the airport expansion requires stabilization of subsurface soils for the construction of three grade separation structures at two roadway interchanges and the intersection of a roadway and taxiway serving the airport. Loose sandy fills and soft Bay Mud were improved by Cement Deep Soil Mixing (CDSM) for the construction of a soil-cement foundation under the MSE (Mechanically Stabilized Earth) walls of a roadway overcrossing and a soil-cement gravity retaining wall to maintain stability of a roadway undercrossing during and after a major earthquake. CDSM was also used to construct two cutoff walls for groundwater control. A test section was carried out prior to full production to verify that the CDSM equipment, installation procedures, and mix designs could produce the soil-cement with required strength, uniformity, and permeability to meet the design intent. Additional test sections were performed for the confirmation or modification of the mix design and installation procedure to cope with the complex subsurface conditions resulting from the historical development of the site. The test section revealed that the CDSM cutoff walls, retaining wall, and foundation improvements could be constructed to satisfy the design requirements and that the intermittent test sections alleviate the impact of the varying subsurface conditions. Based on the data obtained from the test sections, one CDSM cutoff wall was completed in July 2000. Full production of the CDSM retaining wall, cutoff wall, and foundation began in March 2001 and is expected to be complete in November 2001.

Jan 1, 2001

By S. Kelebek, J. A. Finch, Zhenghe Xu, S. R. (Ram) Rao

To improve SO2 emission compliance, pyrrhotite from Sudbury copper-nickel ores is being depressed with DETA. To understand the mechanism of depression, the role of complexing in controlling metal-ion activation of pyrrhotite was investigated. DETA was found to remove Cu and Ni ions but leave hydrophilic ferric species on the pyrrhotite surface. The metal:DETA ratio appeared to be 1:2. Cu was more readily removed than Ni, but the combination of DETA with sulphur dioxide was equally effective for both metal ions. Certain combinations of DETA, Ni ions, xanthate and dithionite (S2O4) or dithionate (S2O6), as representative derivatives of SO2 in water, produced hydrophilic precipitates. These may enhance pyrrhotite depression

Jun 19, 1905

By D R. Peacor, J L. Mauk

Dioctahedral clay minerals in the volcanic-hosted Golden Cross epithermal Au deposit, New Zealand, have been investigated by petrography, X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy/analytical electron microscopy (TEM/AEM) to determine the nature of these minerals in a hydrothermal ore deposit. Heterogeneity in the distribution of dioctahedral clays is observed from the hand-specimen scale to the TEM scale, indicating that primary rock textures and fluid pathways (related to rock type, porosity/permeability and fluid/rock ratios), in addition to temperature, are important factors controlling the distribution. As the proportion of illite in mixed-layer illite/smectite (I/S) decreases, TEM observations show decreasing layer stacking order, parallelism of packets, and packet size, and increasing apparent porosity. AEM structural data show a corresponding decrease in AlIV, AlVI, and K+, and an increase in Si, Ca2+, and Fetotal. The observations of this study indicate that local dioctahedral clay mineral reaction progress is controlled mainly by permeability and structure, but that this is superimposed on a predictable, system-wide clay mineral distribution that is controlled by temperature and fluid/rock ratio.

Jan 1, 1999

By Zsuzsanna Zborovszky

Study of the energy transfer from an inductive circuit to the discharge under the conditions of the minimum discharge voltage being smaller than the source voltage. Analysis of the effect of the electrode separation speed on the duration and maximum power amplitude of the discharge. Recommendation for optimal electrode setting. Experimental data on the variation of maximum discharge power required for ignition as a function of volumetric gas content for methane-air and propane-air mixtures. Experimental determination of the ignition limit for discharges derived from a 24, 15, 10 and 6v inductive-resistive circuit in 8.3% methane-air mixture by using the PTB breakflash with Cd disc and W wires, and also with Cu disc and BeCu wires. Method for calculating ignition limits for other source voltages.

Jan 1, 1978

By M. A. van Nierop

The Discrete Element Method (DEM) is a model that is used to simulate the motion of the media in a grinding mill. The sum of the energy that is lost in inter-media and media-wall collisions represents the power drawn by the mill. The fact that the DEM predicts the power drawn by grinding mills over a large range of diameters has been used to show the validity of the DEM. However, the power drawn by a mill is a function only of the sum of forces of the load on the shell liners. A more accurate and detailed validation of the DEM would be to measure these forces as a function of angular position as the liner moves under the load, and to compare these measurements with predictions generated using the DEM. An experimental mill has been developed to reproduce exactly what the 2-dimensional DEM simulates. The 0,55 m diameter mill has a length of 0,023 m, which is fractionally larger than the diameter of the media used in the mill. One of the lifters in the mill has been instrumented so that the forces on the lifter can be measured as the mill rotates. The DEM simulation will be used to predict these forces. This will give experimental evidence of the validity of the DEM for modelling load behaviour in rotating grinding mills.

Jan 1, 1999

Gippsland has perhaps the most colourful history of exploration of any area in Australia. Hydrocarbons were first discovered in the Gippsland Basin in 1924 when a water well at Lakes Entrance encountered oil and gas shows. In 1942, the Commonwealth and Victorian Governments, in an effort to supplement a wartime oil shortage, sank a shaft near this well and produced 8000 barrels of low gravity oil up to 1956, when the field was abandoned. A total of 64 shallow wells had been drilled in the Lakes Entrance area by that time. Elsewhere in the onshore Gippsland Basin, 30 wells were drilled from 1925 to 1941. In 1960 BHP Ltd was granted an exploration permit covering much of the offshore area of the Gippsland Basin. Esso Australia Ltd joined BHP in 1964 and drilled the Barracouta-1 gas discovery in 1965. Since then over 100 exploration and appraisal wells have been drilled in the basin resulting in the discovery to date of some 3.6 billion barrels of recoverable oil and 8.8 trillion cubic feet of recoverable gas (Current remaining recoverable reserves are 906 million barrels of oil and 5.7 TCF of gas). Exploration in the offshore areas is actively continuing today and new discoveries are still being made.

Jan 1, 1992

By Andrew G. Patton

The Alimak mining method was introduced at the David Bell mine in 1998 to extract an otherwise uneconomic and inaccessible reserve. The success associated with the extraction of these reserves led to major expansion of the method. To date, results have been extremely positive in terms of grade control, reduced dilution, stope recoveries, productivities and mining costs. It is hoped that through further development of the method at David Bell mine we will continue to see positive results in these areas and be able to increase mineable reserves to include proven resources that do not currently meet the criteria of our current stoping plan.

Oct 1, 2001

The Hyde-Macraes Shear Zone (HMSZ) is low angle, duplex thrust system that has developed in a graphitic pelite schist within the Otago schist belt, New Zealand . At Round Hill lateral ramps have developed parallel to the movement direction between+ the footwall and hangingwall shears. These structures exhibit normal oblique-slip displacement which has been an important mechanism for creating space in an otherwise compressional system. Gold-bearing quartz veins were emplaced along the boundary shears and lateral ramps during thrusting. Gold within the lateral ramps is coarse (up to 300 microns) however hanging wall cataclasite development in the boundary shears after the gold was deposited has reduced the grainzise of most of the gold to less than one micron. This bimodal gold distribution has metallurgical implications with respect to the maximisation of gold recovery at Macraes.

Jan 1, 1993