Search Documents

By M. Arvola, A. Mäkinen, N. Isomäki

Arsenic is a compound that has no significant market value. However, it needs to be removed from ores, concentrates and other process streams because of environmental or technical processing concerns. A wide range of arsenic containing minerals exists in nature, and in many instances these minerals are also associated with the ones that have commercial value. For example, sulfide copper ores are normally closely associated with minerals like enargite, Cu3AsS4 and tennantite Cu12As4S13. After mineral processing these arsenic sources can report to the waste waters and these effluents need to be treated before discharge or recycling. Ferric arsenate precipitation is a well-established method for stabilizing arsenic in effluents. Electrochemical arsenic removal utilizes the same adsorption/precipitation ideology as ferric arsenate precipitation. Electrochemical arsenic removal, even though it is a simple process in terms of equipment, is a complex system involving chemical and physical mechanisms taking place simultaneously to remove dissolved and/or solid arsenic components from wastewaters. The whole process can be described by the following three steps: 1) electrolytic oxidation at a sacrificial anode (dissolving electrode metal, iron for example), 2) chemical reaction between dissolved iron and arsenic to form a solid precipitate and 3) aggregation of the particles to form flocs, which can be removed by known solid/liquid separation methods. Electrochemical arsenic removal is a very efficient way to remove arsenic from different waters to very low residual concentrations.

Jan 1, 2016

By D. S. Burgess

About 100 tests of flammability were carried out with H2, CH4, and CO in mixtures with air using the Federal Bureau of Mines 12-ft-diameter spherical pressure vessel as an explosion test chamber. The LeChatelier approximation gave slightly conservative estimates of the limits of downward flame propagation (onset of significant pressure rise) using the following measured values for the individual gases, in percent: H2, 8.5; CH4, 5.25; CO, 13.0. No justification could be offered for using the LeChatelier law for upward flame propagation limits and indeed reported data suggest that calculated values would not be conservative. The observed upward limit for methane-air mixtures (4.85 pct) was less than the widely accepted lean limit for this fuel; those for lean hydrogen-air mixtures and carbon monoxide-air mixtures did not differ from the lowest accepted values. Diffusional effects on the propagation of single, binary, and ternary fuel mixtures are discussed.

Jan 1, 1982

By D. A. Bruce

The paper describes the construction of 5 plugs to resist high water heads at depth within the South Deep Gold Mine, Randfontein, South Africa. A total of 20 segments were involved to create these plugs, which were 7.5 m long at the 58 Level and 6.25 m long at the50 Level. Emphasis is placed on the QA/QC and verification methods, which were developed and governed all phases of the work, from initial rock preparation and pregrouting through to the final grout tightening of the rock/plug interface and the surrounding rock. This paper is one in a series of papers detailing other aspects of the project, which was constructed largely between May 2001 and August 2003.

Jan 1, 2006

By Ian D. Pirie

Presentation outline ?Project location ?Geology ?Resources and reserves ?Results of the FEED study ?Social and environmental considerations ?Project path forward

May 1, 2010

By Gabriel Esterhuizen

Observations of pillar conditions in limestone mines showed that the presence of weak bands in the limestone can result in pillar damage at stresses that are lower than one would otherwise expect. The objective of this National Institute for Occupational Safety and Health study was to investigate the mechanism of failure caused by the presence of weak bands by using a series of numerical models based on realistic physical properties. The effect of the weak bands on pillar strength was also investigated by developing a series of pillar models with different width-to-height ratios and determining their strength by simulating a servo-controlled loading condition. The material properties of the bands and the limestone were varied and their effects on pillar strength were determined. Model results demonstrated failure development similar to the pillars observed in the field. The weak bands were seen to develop tensile stresses in the limestone as they extrude under increasing stress. The limestone fails in tension at a much lower stress than its expected uniaxial compressive strength. The results showed the load bearing capacity of the pillars can be reduced significantly by the presence of multiple thin weak bands. The degree of strength reduction is largely dependent on the compressive strength, the frictional resistance and the thickness of the weak bands. Single weak bands do not affect pillars as severely as multiple bands. However, the model results show that a single thick weak band, which comprises more than about 2 percent of the pillar height, can cause a significant reduction in pillar strength. The weakening effect of the bands become less severe as the pillar width-to-height ratio is increased. Field observation of spalling and failure associated with weak bands in limestone pillars show that the failure mechanism in the models resembles the observed failure. The model results provide insight into the important factors affecting pillar strength in the presence of weak banded materials.

Jan 1, 2007

By J. M. Benson

Titanium is an exciting structural material that can offer significant strength-to-weight advantages over currently used alloys. However, its Achilles? heel is its costly, energy-intensive production process that effectively eliminates it from competing with aluminium and high-strength steels, apart from critical applications where titanium forms only a small component of the total cost. Current attempts are being made to reduce the cost of titanium products and these recognize the importance of minimizing the costs over the total production chain. Powder metallurgy (PM) technologies play a crucial role within this, as the output of the existing and potential primary metal production methods is in the form of sponge or powder. By using PM, costly remelting and forming operations can then be avoided, except in the manufacture of large components. Metal injection moulding (MIM) is an effective process for producing complex net-shape components in large volumes from metal powders. Nevertheless, the commercial use of titanium powders in this process is still in its infancy. The only major supplier of feedstock utilizes a polyacetal-based binder. This gives good green strength but requires a catalytic nitric acid process to remove most of the binder prior to thermal treatment. As this involves additional and expensive equipment and is a potentially hazardous process, there is interest in finding an alternative binder system that can be debound either purely thermally or that involves a less hazardous, more environmentally friendly solvent. This paper describes the use of capillary rheometry to characterize the influence of temperature and shear rates on the flow behaviour of potential binder systems for titanium MIM feedstock. Keywords Titanium, metal injection moulding, capillary rheology, feedstocks, powder loading.

Jan 1, 2011

Stope support systems, typically consisting of props and packs, are used extensively in the gold and platinum mining industry to stabilize the rock mass in the excavation vicinity and to reduce the hazard associated with rockfalls and rockbursts. The design of stope support systems was historically based predominantly on past experience and practices, and cost considerations. The recent development of a new and improved support design methodology, has led to the potential for significant increases in worker safety and support cost savings. This paper reviews some of the fundamental rock mass and support criteria that form the basis of the improved support design methodology. The considered design criteria are the height of potential fall; quasi-static stope closure rates; dynamic stope closure rates; compressive hangingwall stresses; discontinuity spacing, orientation and interface properties; effect of support length (stoping width); effect of compression rate; consistency of support performance; a real coverage; support spacing; and zone of support influence. The proposed support design methodology combines both the zone of influence and key block stability theories, resulting in optimized support systems for rockfall and rockburst conditions. The site-specific methodology consists of two stages: (i) a tributary area analysis, and (ii) a zone of support influence and a stability analysis, considering hangingwall failure due to buckling, shear and block rotation, which gives maximum safe spacing of individual support units. The methodology is suitable for designing support systems for both blocky hangingwalls and hangingwalls fragmented by face-parallel extension and shear fractures.

Jan 1, 2001

By C. J. Cutler

Metallurgical accounting for toll treatment smelters pose a number of challenges. Multiple feed stockpiles have to be accounted for as part of the monthly recovery estimation. Moreover, multiple metallurgical intermediates make up part of the in-process inventory, which also influence the monthly recovery calculation. Errors propagate from the measurements of volumes, assays, moisture fractions and bulk densities in the various material types through multiple steps up to the point where the final recovery is calculated. These errors contribute non-linearly to the variance in the final recovery estimate. This paper develops the mathematical formulation for variance propagation in toll smelting operations, including the effect of in-process inventory, assuming measurement biases have been eliminated beforehand. Operational data from a Southern African copper smelter is used for a case study. The method of propagation of variance showed that uncertainties in stockpile assays were the main contributors to variance in the recovery estimate. Variance in the volume and bulk density uncertainties contributed a secondary, yet significant, proportion to the overall recovery variance. It was determined, for the given case study, that the recovery variance depended on the calculation method used and that variance propagation via the two-product formula was smaller than recovery variances calculated via the standard recovery formula. However, the probability that the two product formula will give inaccurate (versus imprecise) results is significantly more due to the practical difficulty of equiprobable sampling of tailings streams from smelter plants (which includes materials such as slags and flue dust). Recommendations are made on how to achieve a reduction in overall uncertainty for toll treatment smelters. Keywords: metallurgical accounting, copper smelters, pyrometallurgy, variance propagation, errors, precision, sampling

Jan 1, 2006

By P. Golledge, A. D. S. Gillies

An investigation has been carried on samples of three Queensland coal dusts to determine the potential explosibility of dust-gas mixtures. The explosion potential of the samples was classified by the lean and rich limits of explosibility and the limiting oxygen concentrations for each sample. Plotting of these points showed 2-dimensional flammability limit surfaces for coal dust/oxygen, methane/oxygen and coal dust/methane mixtures. From these plots the 3-dimensional flammability envelopes defining the explosibility of the mixtures were defined. The explosion limits of the coal dust/methane/oxygen system were seen to be influenced most by the explosibility characteristics of coal dust. Methane exerted a stronger influence over the explosion limits when the coal had a low volatile content

Jun 19, 1905

By Patrick J. Doig

In mid-1991, the design/build contractor set to work on the Pergau HEP in a remote corner of Malaysia, armed with only a slim volume of conceptual drawings. The next five years saw roads, power lines, buildings, dams, and over 30 kilometers of tunnel constructed, followed by two years of E&M installation and commissioning. Along the way, the project overcame geothermal groundwater, faults, land disputes, monsoon rains, marauding tigers, and those most fearsome of foes, politicians and the press. This paper is a testament to the ingenuity, commitment, and persistence of the construction industry professionals who brought this massive project to fruition.

Jan 1, 2001

By E. Robles

The Tati Activox® Project (TA®P) is the first step towards the implementation of the Norilsk Nickel Activox® process. The ultrafine grinding (UFG) and autoclave pressure leach process conditions are the heart of the Activox® patent. Low grade base metal sulphide concentrates are leached in the process to recover the base metals and to produce LME grade nickel and copper cathodes and cobalt carbonates. The downstream processing of the metal-containing liquor produced by this process includes solvent extraction circuits to extract and concentrate metal-rich solutions, before the various final products are obtained. This paper gives an overview of many of the relevant design aspects taken into consideration in the design of the Tati Activox® solvent extraction circuits. It addresses key design elements related to leach process conditions such as scaling, materials selection for corrosive solutions, pH control, crud formation and treatment, multiple SX trains designed to prevent organic cross-contamination, and design aspects related to the mitigation of fire risks.

Jan 1, 2009

By Brandon Fryman, Josh Hoffman, Rhys Baker

A post-detonation debris collection project was led in conjunction with a large ammonium nitrate(AN) railcar detonation conducted by the Department of Homeland Security-Transportation Security Administration, Department of Defense-Combating Terrorism Technical Support Office, Sandia National Laboratories, and the U.S. Army Dugway Proving Grounds. This important work will aid in underpinning algorithms used in a Quantitative Risk Assessment (QRA) tool. The test also provided valuable data about the effects and consequences following an AN detonation. The test took place at the Utah Dugway Proving Grounds on April 27, 2018 and the debris collection was conducted the following two weeks with an average of 20 persons per day and an approximate total of 1,400 manhours. A paper was presented at the 2019 ISEE Conference on the collection efforts, challenges, and lessons learned. A complete data analysis effort was completed on the test data in 2019 that resulted in updates to the QRA Railcar Potential Explosion Site (PES)model and AN engine. The analysis included an assessment of the debris data resulting from the Derailed test. This paper is meant to serve as a summary of the analysis effort and findings and as an update to the previously presented lessons learned from the debris collection and analysis effort.

Draft tube circulators are now widely used instead of Pachucas for suspension of slurries in large tall tanks.Precipitators in the alumina industry are an example.Draft tube/tank diameter ratio is critical. Two independent criteria are given for optimum ratio. The hydraulic and energy relationships are defined. These require an impeller of very high specific speed. For a stable and efficient system the impeller should have aerofoil blades with a pitch angle which decreases from hub to tip.The draft tube must be matched to the impeller with inlet baffles above the impeller and flow control vanes below it. Tip recirculation must be suppressed. The tank itself should have a filleted flat bottom.Such a system exhibits the behaviour of axial flow devices with the characteristic undesirable behaviour at low flow.Installed and operating power requirements depend critically on hydraulic design and to a lesser extent on speed reducer efficiency.The problems of re-suspension have been overcome by a patented slot system which also improves behaviour at low flow to permit a more economic design. A number of other practical operating considerations are also discussed.

Jan 1, 1982

The 105th Annual General Meeting of The South African Institute of Mining and Metallurgy was held in the J.C. Lemmer Auditorium, SA National Museum of Military History, 22Erlswold Way, Saxonwold, Johannesburg on Thursday, 8thAugust, 2002. Welcome The President extended a special welcome to the guests and representatives of our sister institutes and other associations. Also to recipients of awards, senior members of industry, Honorary Life Fellows, Past-presidents, our Members and other guests, among them the following: Mzolisi Diliza, Chief Executive, Chamber of Mines of South Africa Dawie van Wyk and Rod Tucker, Vice-presidents, The Geological Society of South Africa Vaughan Townsend, President, Institute of Certificated Mechanical and Electrical Engineers, South Africa Karel Landman, President, Institute of Mine Surveyors of South Africa Frik Grobbelaar, South African Colliery Managers? Association Pierre Ballot, President, South African Institute of Electrical Engineers Trueman Goba, President, South African Institution of Civil Engineers

Jan 1, 2002

By G T. Kukla

A Seam deposit User oriented Mine Planning System (SUMPS) was developed by The Broken Hill Proprietary Company Limited (BHP) at its head office in Melbourne. It is one of the computer mine planning systems developed by the Corporate Data Processing (CDP) section of BHP. To date it has been employed in the feasibility study of four coal prospects for the BHP Group, including Gregory in central Queensland û Ham and Van Hoorn (1978). It was also used in detailed short term mine planning for Gregory. A recent application was in the feasibility study of Saxonvale, a multi seam coal deposit in New South Wales with seams up to 20 m thick. The other two applications of SUMPS were also on thick multi seam coal deposits. Development of programs for the underground subsection of SUMPS is continuing. SUMPS was developed and implemented on mini computers with graphics and plotting peripherals. The company's philosophy towards computing is one of centralized development and project planning, with transfer of hardware and software to site once the mine becomes operational. Support of the site's system continues from head office which is continually involved in development of SUMPS and issuing revision updates to sites. The users, as well as programmers, were mostly geologists and mining engineers. This helped to ensure rapid, successful implementation. The broad approach of this system was to use interactively the specialist skills and interpretative abilities of the user mining engineers and geologists with the data manipulation abilities of the computer. It is an integrated system which covers geological exploration, deposit modelling, mine planning and production scheduling. An important feature of the system is that the user has full interactive control over each function through a graphics terminal where applicable.

Jan 1, 1980

This Bureau of Mines publication consists of an overview of the mine waste management research currently being conducted by the Bureau. The following papers, given at a Technology Transfer Workshop, emphasize the increasing importance of research related to the safety and environmental considerations of mine waste disposal In recent years. Current work related to legislation passed in the last 10 years and their subsequent standards includes the development of adequate monitoring systems, development of stability and seepage prediction and control techniques, control of runoff water, and control of leaching solutions. Selected topics are included here that cover coal mine waste disposal, embankment slope stability monitoring, flow failures of mine tailings impoundments, and controlled burnout of abandoned coal mine fires. The projects described provide a current documentation of problems being addressed.

Jan 1, 1981

As mine haulage vehicles become larger, the danger to a driver during a fire emergency is increased by the greater height of the cab above ground. Also, property damage due to fires on bigger trucks can be substantial. To solve this problem, the Department of Interior's Bureau of Mines, through two research and development contracts with FMC Corporation, San Jose, California, has developed two reasonably priced, reliable automatic fire sensing and suppression prototype systems for large haulage vehicles. At the onset of the large mobile equipment fire protection contract effort, it was learned that fires were frequently experienced in open-pit mine haulage equipment, especially large trucks. As the size of equipment has grown, so has the hazard presented to an operator forced to leave his truck in a hurry when fire breaks out and his normal path to the ground is blocked by flames. His only recourse is to jump from the cab platform to the ground, and the one-story drop of 10 feet or more can severely injure him. It is with these factors in mind that a program was undertaken to provide a fire detection and extinguishing capability tor the large mobile equipment, especially trucks, used in open pit mines.

Jan 1, 2012

By Laurance L. Oden

The Bureau of Mines is developing melting data for binary combinations of the alkaline earth fluorides and yttria to facilitate the formulation of slag composition. Liquidus and solidus temperatures and solid solubilities were determined for the BaF2-Y203 system, and the information is presented as the phase diagram. The phase diagram was constructed from data obtained by ceramography, X-ray diffraction, and thermal analysis of specimens encapsulated in small molybdenum ampoules. The data indicate a simple eutectic system with maximum terminal solid solubilities of less than 1 mole pct. The eutectic temperature is 1,343° C, and the composition of the eutectic is less than 1 mole pct Y203.

Jan 1, 1970

By J Seppelt, B Akerstrom, J Bubnich, D Seaman, T Waters

The Cadia Hill concentrator at Newcrest’s Cadia Operations has undergone several modifications and upgrades to treat an increased throughput rate of harder ore from the Cadia East block cave mine.Subsequent to the commissioning of the expanded circuit, the flotation cleaner block has undergone a systematic optimisation programme tackling all facets of circuit operation. This included debottlenecking circuit constraints and installation of Jameson cell technology to enhance copper and gold recovery while rejecting fluorine and gangue from the concentrate.This paper outlines the improvements over the course of the project and results obtained from the implemented actions.CITATION:Akerstrom, B, Seppelt, J, Waters, T, Bubnich, J and Seaman, D, 2018. Cleaner circuit optimisation at Cadia Operations, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 457–476 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By Jan E. Nesset, Julie Fournier, Jorge Torrealba, Colin Hardie

"Gas dispersion studies have been used to benchmark and optimize plant flotation performance for more than a decade, although this technology is not as widely in use as it likely should be based on the significant improvements that have been reported. Part of the reason may be a general lack of awareness within the industry of just what these improvements have been. This paper reviews a number of the reported case studies, groups them into categories of improvement, and draws some general conclusions. The paper will be of interest to plant engineers and technology providers seeking new approaches and tools for improving their own and clients’ processes.INTRODUCTIONThe sector of flotation hydrodynamics that is now known as gas dispersion technology, and the corresponding terminology, had its beginnings in the 1980’s and early 1990’s in the laboratories of McGill University where the students of Prof. J.A. Finch and Dr. C. Gomez conducted studies of gas holdup, superficial gas rate and water recovery on laboratory flotation columns (Laplante et al., 1983; Xu et al., 1991;, Banisi and Finch, 1994; Finch et al., 1999; Nesset, 2011). Sensors were developed for gas holdup (eg), gas rate (Jg) and bubble size (Db) distribution (Tavera et al., 1996: Finch et al., 1999; Dahlke et al., 2001; Chen at al., 2001; Hernandez-Aguilar et al, 2002, 2005). The sensor measurements were rapidly adapted for use in mechanical flotation machines in plant environments (Gomez and Finch, 2002; Gomez et al., 2003; Cooper et al, 2004; Torrealba-Vargas et al, 2004; Nesset et al., 2007). Somewhat parallel developments were being conducted by Gorain and colleagues at the University of Queensland’s JKMRC on pilot and industrial flotation machines using the McGill approach but utilizing alternate sensor designs for eg, Jg and Db (Gorain et al., 1997, 1999; Schwarz and Alexander, 2006) to link flotation kinetics to bubble surface area flux (Sb). Early industrial applications were those led by the university teams from McGill (Canada), the JKMRC (Australia) and the University of Santa Maria (Chile) at plants in North and South America, Australia, South Africa, Asia and Europe. Industrial organizations that brought the technology on-board in the early 2000’s included Teck Resources (then Teck Cominco), COREM, Vale (then Inco), Anglo American Platinum. Several of the major flotation cell manufacturers also purchased the McGill bubble viewer technology for their own equipment studies. The sensors have continued to evolve with multiple and continuous measurement of Jg (Torrealba-Vargas and Finch, 2006, Bartolacci et al., 2008), gas holdup by acoustic means (O’Keefe, 2007) and a combined Jg-Db device called the Anglo Bubble Sizer (Harbort and Schwarz, 2010). A review of the gas dispersion technology use and development have been provided by Gomez and Finch (2002), Harbort and Schwarz (2010) and Nesset (2010)."

Jan 1, 2015