Search Documents

By Emad Farouz, Ehab S. Shatnawi

"The increasing demand for small deformations and high-capacity drilled shafts without enlarging drilledshaft diameters has motivated the development and increasing use of a base grouting (BG) technique. This technique has been demonstrated to improve drilled-shaft capacity, especially for shafts tipped into loose cohesionless soils. Nevertheless, there remains considerable uncertainty in predicting the performance of base-grouted shafts, particularly for shafts tipped into cohesive soils. To date, there are only two documented design methods for estimating the axial geotechnical resistance of base-grouted shafts: Tip Capacity Multiplier (TCM) and Axial Capacity Multiplier (ACM) methods. A comprehensive test program was carried out during the design phase of the Wisconsin Zoo Interchange project to help optimize the flyover ramp’s foundation design. The test program included installing and testing one base grouted shaft and one ungrouted shaft at two sites with different ground conditions. Based on test results, it was concluded that prediction of the TCM method is well correlated with the measured values for both cohesive and granular soils; however, both methods tend to underestimate the axial resistance. Results also highlighted the importance of the base-grouting criteria in taking full advantage of the base grouting.INTRODUCTIONBase-grouted drilled shafts (BGDS), also known as post-grouted drilled shafts, consist of conventionally installed drilled shafts that contain access grout tubes placed within the shaft during construction. After installing the drilled shaft and achieving the pre-established concrete strength, grout is injected at the shaft tip through the access grout tubes to improve soil behavior around the drilled-shaft base. The tip grout injection improves the overall shaft capacity and reduces settlement through Densifying the in situ soils, compressing any debris left by the drilling process, preloading the soil beneath the tip to mobilize the shaft base resistance within service limits, increasing the tip area, and increasing the side resistance in the lower portion of the shaft."

Jan 1, 2016

By William Brundan

INTRODUCTION The Srisailam Left Bank Canal (SLBC) Tunnel Scheme is part of the Alimineti Madhava Reddy Project in Andhra Pradesh, South India. This scheme has been planned since 1983 and will provide irrigation facilities to drought-ridden areas in Andhra Pradesh. Water will be transferred from the Srisailam Reservoir during the monsoon months to 0.3 million acres of farmland and will also provide drinking water to villages en-route. The paper will address the design and onsite assembly of the Robbins Double Shield TBMs for Tunnel-1 of the SLBC tunnel scheme from planning to start-up of the machines. Also, it will provide a current status of the project and describe the advantages of a site assembly. Problems encountered to date and the solutions adopted will also be described. The project comprises over 50 km of tunnels and involves construction of the world?s longest tunnel without intermediate access. The TBM tunnels at 43.9 km in length and 10.0 m diameter will cross the Amrabad plateau, containing a wild life sanctuary and India?s largest tiger reserve, the Rajiv Gandhi. Jaiprakash elected to excavate the tunnel using two tunnel boring machines, rather than by drill and blast, in order to alleviate surface disturbances to environment and the tiger reserve, wild life sanctuary, and protected forestry areas. The Project was awarded to the Main Contractor Jaiprakash Associates Ltd with The Robbins Company as the Tunnel Boring Machine (TBM) supplier in August 2005. The Robbins Company supplied the TBMs along with two continuous conveyor systems and all spares and consumables to complete the tunnel excavation.

By Timothy J. Myers

Expansion and the economic growth in the southwestern region of Missouri necessitated the expansion of State Route 249 and the construction of a new interchange to provide service to the Joplin, Missouri area. The project is located above a former lead and zinc mine in Jasper County, Missouri and includes a five bridge interchange connecting State Route 249 and US Route 171. The variable subsurface conditions, both natural and manmade, prompted the design team to use ground improvement via grouting and small diameter micropiles to provide support for several of the bridge foundations on the project. The scope of work included mine shaft closures, 56,000 ft of overburden and rock drilling, 11,139 ft of micropiles, 524 cy of balanced/stabilized high mobility grouts, and over 8,700 cy of low mobility grout. The selection of the grout used was based on the actual subsurface conditions. Low mobility grout (LMG) was used in voided conditions and for closure of the mine shafts encountered during the excavation. High mobility grout (HMG) was used in fractured rock with the goal of improving the mechanical properties of the rock underneath the future bridge footings and controlling grout volumes during micropile installation. The split spacing method was utilized for both LMG and HMG holes. Geology of the project site subsurface consisted of extremely variable bedrock with strong to very strong limestone, chert, breccia, extremely weak shale, and weak to strong sandstone. Previous activities associated with the mining disturbance (such as partial filled vertical mine shafts, shallow and deep mine horizons, modified hydrology including artesian conditions) further complicates the site subsurface conditions. Real time monitoring and recording of all drilling and grouting parameters was conducted to assist in the evaluation of in-situ geological properties of the site in order to modify the ground improvement and micropile program as necessary. This paper will discuss the design and execution of the ground improvement and micropile program. The project is an excellent example of the use of multiple ground improvement and foundation support techniques combined with real time data analysis to provide a foundation support solution for a complex geological environment.

Jan 1, 2009

By Bowen Li

Andalusite is an excellent raw material for refractory applications due to its high aluminum oxide content and phase transformation to mullite at high temperature. Granular andalusite in particle sizes of about 1 to 2 mm was traditionally utilized for the manufacturing of refractory brick. However, if powder andalusite in micron particle size is utilized in high-alumina refractory products, reinforcement on the refractory brick can be obtained and the sintering temperature can be decreased. The phase transformation of powder andalusite plays a key role for the difference.

Jan 1, 2006

By Djavid Mohammad

Over the next several years, the storage capacity of the Metropolitan Water Reclamation District of Greater Chicago?s Tunnel and Reservoir Plan will be increased by 14.8 billion gallons through the addition of two large off-line reservoirs: the McCook and Thornton Reservoirs. The Thornton Reservoir will be constructed at the terminus of Calumet TARP System. The constructed TARP system will be connected to the Thornton Reservoir via connecting tunnels and gates systems. The connecting tunnels will comprise of: an upgradient transition tunnel, steel lined bifurcated tunnel for conveyance and control of flow, downdradient transition tunnel, and energy diffuser at tunnel portal. A large, approximately 250-foot-long, 69-foot-wide, and 40-foot-high, rock cavern will be excavated at an average depth of 320 feet to house the bifurcated tunnel system and associated six large control gates, each 12.5-ft by 28-ft wheel gate. Presented in this article are discussions about the TARP system, the Connecting Tunnels and gates Project, regional rock conditions, evaluation of reservoir?s wall stability for evaluation of tunnel penetration, and design challenges facing during design of the: rock cavern hosting the bifurcated tunnel system and gates and associated tunnels and shaft.

Jan 1, 2008

By Edward Walter

Rock excavation for tunneling projects occurs on a regular basis in the Cleveland area. These tunnels are being constructed to increase the capacity of the sanitary sewer system. Controlled blasting must be performed to remove rock in a number of phases of the project. The rock excavation for construction of a junction chamber is just one case where blasting is the safest and most efficient method available.

Jan 1, 2001

By J. R. Goode

"The Las Cristinas deposit in Venezuela contains reserves of 12.8 million ounces of gold at a grade of 1.20 g/t (Crystallex, 2004). The deposit comprises fully oxidized saprolite (SAPO) overlying a layer of sulphide-enriched saprolite (SAPS) which lies above carbonateleached bedrock (CLB) and carbonate stable or un-leached bedrock (CSB). Gold occurs at about the same concentration in all lithological groups. The bedrock units contain minor amounts of copper (about 0.1%) as chalcopyrite, while SAPO contains virtually no copper which has been leached and deposited in the SAPS zone.A previous owner began investigation of the Las Cristinas deposit in 1991. Over the next seven years, the company drilled 1,174 holes with a total length of 159 km, conducted extensive metallurgical testwork, including pilot plant operations, and completed feasibility studies. Construction was started in 1997 and again in 1999, however, on each occasion was suspended.Crystallex has been producing gold inVenezuela since the early 1990s. In 1997, Crystallex acquired Inversora Mael which had held two of the claims to the Las Cristinas concessions since 1986. In September 2002, Crystallex entered into a definitive agreement with the Corporación Venezolana de Guayana (CVG) to develop the Las Cristinas deposit.An extensive program of studies and testwork was started in late 2002 to determine an optimum development plan for Las Cristinas. Mine Development Associates, SNC–Lavalin Engineers and Constructors, SGS Lakefield Research Limited, J.R. Goode and Associates, and A. Laplante at McGill University acted as the main contractors.Because of the potential value of by-product copper, earlier flowsheets used carbon-inleach for SAPO, but processed all other ore types by flotation to produce a gold-copper concentrate with cyanide leaching of cleaner tailings to maximize gold recovery. Cyanide recovery was necessitated by the high copper content of the leach feed. Initial studies of available data by Crystallex revealed that direct leaching of all ore types would provide about 11% more gold recovery than the previously selected flotation route with reduced capital and operating costs.Bench and pilot-scale studies have confirmed that a SAG-ball mill-gravity-CIL route is very effective for all ore types and will give about 89% gold recovery. This paper describes the testwork conducted in 2003, discusses a 20,000 t/d plant design, and presents economic data."

Jan 1, 2005

Triboelectric Charge and Separation Characteristics of Industrial Minerals The basic principles of triboelectric charge and separation of minerals and the factors affecting the entity of the charges developed on mineral surfaces are discussed and the surface pretreatment methods by which the electrophysical properties and thereby triboelectric charging and separation of minerals can be artificially altered/modified are reviewed. Furthermore, the triboelectricfication theory of materials is envisaged from the chemical concept of acid-base donor-acceptor and an attempt is made to correlate the physical concept of triboelectrification with the donor-acceptor properties. The triboelectric charge characteristics of the quartz, calcite and wollastonite mineral samples for different size classes were defined using different tribocharging medium. Based on the triboelectric charges acquired by mineral samples their energetic work function values are estimated. In addition, the main electrophysical properties, ie dielectric constant and electrical conductivity, of different size fractions of the mineral samples are measured and their donor-acceptor chemical properties were defined. A series of triboelectric separation tests were conducted to explore the possibilities for separation these mineral from each others. The results from the triboelectric charge and separation of the single mineral systems showed promising prospect in separating quartz, calcite, and wollastonite from each others. Finally, attempts were made to explore the possibilities to implement triboelectric charge and separation process to real ores. Promising results achieved when separation of calcite from silicate impurity was sought from a carbonate ore. A very high purity (99 per cent) calcite product was obtained at a recovery of 80 per cent. Interesting results were also achieved to concentrate wollastonite from a complex silicate ore containing quartz, different feldspars, wollastonite and other Mg-Fe silicates. In this case conditioning of the ore with salicylic acid at defined temperature and relative humidity was found to be essential to concentrate wollastonite. The outcomes indicate despite the fact that triboelectric charge and separation process has not been completely perceived, it pronounced to be an environmentally friendly and economically viable technique for minerals and wastes beneficiation. Being a dry beneficiation technique the process has special appeal, which must be explored further in particular for treating industrial minerals.

Sep 13, 2010

By Patrícia Freitas Rodrigues

Um comparativo entre dois métodos para determinação das temperaturas de transformação de fase, tendo como base análises de Calorimetria Diferencial de Varredura (DSC) em amostras de uma liga de NiTi equiatômica submetida a tratamentos térmicos para envelhecimento, foram utilizados neste trabalho. Sendo aplicado o método clássico comumente utilizado para análise desses resultados e o método utilizando da integral do pico de transformação de fase. Com base nas avaliações feitas, o método de integral por apresentar uma relação direta da fração de transformação demonstra-se mais eficaz para determinar o início e o fim da transformação por levar em consideração a forma do pico em função da trajetória de transformação.

Aug 8, 2018

The validity of a steady state assumption made by Adams and Nicol (1986) in the modelling of the elution of gold from activated carbon was investigated. It is shown that the accuracy of the steady state approximation is dependent, not only on the magnitudes of the solution flow rate and reactor volume, but also on the lumped elution rate constant. Under the experimental conditions used by Adams and Nicol (1986) the steady state assumption was inaccurate. This could be circumvented in this instance by applying a rigorous general model which accounts for unsteady state behaviour in the solution and in the activated carbon to the experimental data.

Jan 1, 1997

By A Mooney, G Balog, P Burns, R Brooks

This paper outlines the rationale for the location of the crusher, geotechnical analysis and basis of ground support design, design and scheduling of the chamber and supporting excavations as well as the operational outcomes and lessons learned. Contributions from mining operations, planning, geotechnical and infrastructure teams enabled the Crusher Station One excavation to be completed on schedule, with opportunities taken for underground mining and infrastructure to work safely in parallel to deliver crusher station infrastructure on schedule. Installation of crusher infrastructure was ongoing at the time of writing.

Mar 15, 2021

Active geothermal fields show many of the characteristics seen in hydrothermal ore deposits but there are important differences as well. There are, for example, many differences in geology and chemistry between individual geothermal fields, even some nearby, and these include variations in host rock types (volcanic, sedimentary, plutonic and metamorphic), structures controlling fluid flow (normal, lateral, and, rarely, reverse faulting occur) and hydrological setting (valleys to elevated terrain).

Jan 1, 1986

By H. C. Hamontre

[The Bureau of Mines well-bore caliper was designed to provide an instrument that could be operated through 2-inch tubing, which 'a used particularly in many input wells on water-flooding projects of eastern, Kansas and northeastern Oklahoma. It should find wide application elsewhere under many other conditions where it has not been possible previously to make caliper logs with the larger probes used on other instruments. The caliper has three additional advantages over other instruments of this type: (1) It measures 4 radii (up to 18 inches) 90° apart with an accuracy of ± 1/4 inch; (2) the measuring arms can be opened and closed at will by remote control; and (3) it is run and operated on a single-conductor, armored electric cable (Amergraph, type 1-H-0). The caliper probe is 1-3/4 inches in diameter and approximately 6 feet in length. The electrical control and measuring circuits are encased in a stainless-steel tubular case. Measuring arms, made of 5/16-inch aluminum tubing, are attached near the lower end of the instrument. Distances the arms are extended are indicated t the surface by a meter calibrated to read directly in inches. Depths at which the radii measurements are taken are indicated by a wireline depth indicator on the cable-reeling. The instrument is not affected by pressure or temperature, it can be run open hole or under pressure through a lubricator. This paper describes and illustrates the instrument and outlines the operating procedures. A bibliography at the end of the report gives references to articles and patents on the development and use of other well-bore calipers.]

Jan 1, 1954

By Kiseong Hyeong, Young-Tak Ko, Gee Soo Kong

"The benthic environmental impact experiment addresses environmental impacts at a specific site related to deep-sea mineral resource development. For such a purpose, since 2010 we have carried out essential environmental research at both the BIS and a preservation site. We have acquired several tens multi- or box core samples at 32 sites within the BIS especially between 2011 and 2013, aiming to examine the basic properties of surficial deep-sea sediment as the potential source for deep-water plumes.In this study, we present physical the properties such as water content, shear strength and also geochemical properties such as major elements, rare earth elements (REEs), heavy metal contents at the BIS. Such proxies vary distinctly according to the Facies association. The lithology of all core sediments in the BIS corresponds to both Association Ib (Unit I/Unit II) and Association IIIb (Unit I/Unit III) on the basis of the KORDI classification (KORDI, 2004); Unit I is watery mud and dark grayish brown (10YR4/2) to dark brown (10YR4/3). Unit II is highly bioturbated mud and brownish yellow (10YR6/6). Unit III is very dark brown (10YR3/2) to black (10YR2/1) mud. Physical properties of these sediment types show that Association Ib is distinct from Association IIIb. The vertical profile of water content changed more sharply in Association IIIb probably due to compaction; water contents varied from 230 to 300% in Association Ib and changed from 200 to 250% in Association IIIb. The vertical profiles of shear strength are also quite different between Associations; the profile curve in Association IIb is much more gentle due to bioturbation."

Sep 1, 2014

The increased focus on best practice environmental management has led to mining and mineral processing companies developing a variety of procedures to ensure that the environmental impacts of their operations are minimised, and that company managements are fully aware of these impacts and the policies and procedures established to ensure this process. Parallel to this, international standards for the development and implementation of environmental management systems are being promoted as necessary for companies to demonstrate their due diligence. Good environmental management systems should be built upon the systems already established within companies, and should ensure that the process of continual improvement is integral to their operation. An outline of the basic components of environmental management systems is provided, along with examples of the way various mining companies have implemented such systems. The benefits of best practice environmental management to mining companies are also considered.

Jan 1, 1995

By A. B. Parsons

DOWN in Washington an army of individuals constituting the government of a so-called "'democratic" nation is trying to manage the conduct, in its rnultifold phases, of the greatest war in history for the country that is potentially, at least, the strongest in the world and on which, consequently, the major responsibility rests. The enterprise is one of unprecedented magnitude and complexity. That individuals and groups have made and are making serious blunders, both as to the establishment and execution of policy, is to be expected.

Jan 1, 1942

By J. T. Nel

The establishment of a pilot plant for the continuous production of titania pigment and nano-titania is discussed. The plant was designed, constructed and operated on the Necsa site. The TiO2 production capacity is 7?10 kg.h-1 by the reaction of TiCl4 and O2at>1000°C. Liquid TiCl4 is sprayed under pressure into a plasma reactor where it evaporates and reacts with O2 to form TiO2. Process optimization has allowed for continuous production without any clogging or blockages. The primary advantage of the plasma-assisted process is the possibility to recover and recycle the chlorine values in high yield as Cl2 for use in the manufacture of TiCl4. The HCl formed in most conventional fossil-fuelled processes makes Cl2 recovery and recycling much more difficult. Particle size distribution analysis of the fine, white product revealed a d50= 125 nm. The raw product consisted of 60% rutile that could be increased to 80?100% rutile by post-annealing. The specific surface area (SSA) of the pigment was 8?20 m2?g-1(BET). According to the CIE colour index the ?whiteness? (L*>95) of the plasma-produced pigment was better than that of several commercially available pigments. The particle size could be manipulated by controlling the TiCl4 feed rate, gas flowrates, and the particle quench rate and residence time. Nano-sized TiO2 powders with a particles size (d50) as small as 50 nm were also successfully produced in this way.

Jan 1, 2010

By R. S. Jurani

Sunshine Mining Co.'s Kellogg operation is the primary silver producer in the US. Maintaining a comfortable working environment in this deep underground mine historically has been a complex and costly problem. To improve the ventilation and cooling systems at a time of declining and un-certain silver markets, it was proposed to optimize the performance of existing facilities at minimum cost. This paper discusses a two-year, $400,000 optimization program that resulted in increased total mine airflow, cooler ambient temperatures, reduced compressed air usage, and lower energy consumption by primary fans, air compressors, and refrigeration plants. This saved the company about $650,000 per year.

Jan 1, 1988

By D. N. Dietz

Jan 1, 1969

By A. M. Khan, I. Fatt

A new type of steady-state thermal conductivity apparatus is presented and described. Results of measurements on Berea sandstone, Solehofen limestone, Bandera sandstone and Bakelite are presented. The measurements were made in a two-hour period at temperatures up to 80C and axial stress to 125 bars. Results show that the thermoelectric heat pump and tbermistor-controlled electric heater can be used in a steady-state apparatus for measuring thermal conductivity of mck. Steady-state is reached within two hours. With Urethane foam insulation, not more than 3 per cent of heat is lost by radial flaw. The apparatus can be used as a comparator or for absolute thermal conductivity determinations. INTRODUCTION Calculations of heat flow through the earth, both for scientific purposes and engineering design, require thermal-conductivity data on rock. However, the high variability of rock often makes handbook thermal-conductivity data of little value. For engineering purposes in particular, it is desirable to have measured data on samples of the rock mass under study. Laboratory methods for measuring thermal conductivity of rock use either time-dependent1-3 or steady - state temperatures .4,5 The time -dependent (transient) techniques give thermal diffusivity from which thermal conductivity can be calculated if the specific heat and density of the sample is known. Most transient techniques require lengthy and involved sample preparation. Also, the accuracy tends to be low. Steady-state techniques are more exact and are the most commonly used. The steady-state methods, however, also have their difficulties. A long time is often required to reach steady state, troubles have been encountered in establishing good thermal contact between the heating and cooling elements and the rock sample, and unaccounted-for heat losses are difficult to prevent. In this paper we present a description of a new type of steady-state thermal conductivity apparatus. With it, measurements have been made in two hours at temperatures up to 80C and axial stress to 125 bars. Sample preparation is simple and no thermal conductivity standard is needed.6 APPARATUS Our steady-state apparatus is an improvement . over the conduction pile used by Zierfuss and van der vliet4 and Somerton.5 A linear heat flux is established through a conduction pile consisting of the rock sample and a standard material of known thermal conductivity in series. The thermal conductivity of the sample is calculated from the ratio of the temperature drop across the sample

Jan 1, 1966