Search Documents

By Carl Fisher

A microseismic roof fall warning system was field tested in Western and Eastern coal mines in the United States to better define the capabilities and limitations of the microseismic method in predicting roof fall Microseismic event and energy type data were obtained and documented for twenty-three coal mine roof falls. Field test results indicate that both the microseismic event and energy methods, as applied in this development effort, have a high probability for successful application in a commercially practical roof fall warning system. Based on the results and experience obtained during field testing, a commercial prototype microseismic roof fall warning system was designed and constructed. Although it was the intent of the program to field test the commercial prototype system, delays in equipment fabrication and contract time limitations did not permit field testing.

Jan 1, 1980

By Pasi Korkeakoski

There are about 400 multi-storey buildings founded on wooden piles in the city centre of Turku in Finland. Soil conditions are variable from hard rock to very soft clay. Due to the soil conditions and ground water lowering there are basically four different types of underpinning projects. Under dimensioned cohesion piles in a deep clay layer, decaying cohesion piles, a combination of these two reasons and decaying end bearing piles in a thin clay layer area. Many different execution methods have been used such as impact driving, jacking and drilling and combinations of these.

Jan 1, 2000

By A. W. BELDEN

Among the investigations that the Bureau of Mines is conducting witha view to increasing efficiency in the utilization of fuels belonging to or for the use of the Government is an investigation of the processesthat take place in a foundry cupola during a melt. Some observations on the results of cupola tests of cokes at the Government fuel-testing plant in St. Louis, Mo., the coke being fromcoal from many coal fields of the United States, have been stated in a previous bulletin.s Especial attention was given to the meltinglosses that resulted from the use of different grades of coke, light and porous or heavy and dense. These losses amounted in one instance to 52.5 per cent of the iron charged and showed, in convincing manner, the need of exact information in regard to conditions in the fuelbed of the cupola.b Melting losses of iron have been fully appreciated but little under-- stood. The fact that these losses were possible with either light or heavy coke led to the belief that by using small charges 80 placed that. melting would take place in that zone of the cupola where the highest heat and the smallest percentage of oxygen prevailed and by confiningall melting to this zone these losses would be eliminated and the economical use of practically any coke produced for metallurgical purposes would become possible. This widening of the field from whichcoke might be drawn for foundry purposes would serve to place the foundryman in an independent position as regards his source of supply, and would tend to conserve the better grades of coking coals, which are being rapidly exhausted, by making the poorer grades available for mixing with them. In order to investigate conditions within a cupola, the Bureau of Mines as a first step decided to install a commercial cupola, to sample the gases during their travel from the tuy~res upward, and to determine the temperature of the fuel bed.

Jan 1, 1913

By S Goff

The Northern Sewerage Project (NSP) is a $650 M infrastructure project that will increase the capacity of the sewerage system for Melbourne’s growing northern suburbs while also helping to protect the Merri and Moonee Ponds creeks by significantly reducing the number of sewage overflows that can occur after heavy rainfall. The NSP consists of two stages: Stage 1 (NSP1) will be owned and operated by Melbourne Water Corporation, and Stage 2 (NSP2) will be owned by Yarra Valley Water and operated by Melbourne Water Corporation.Glass-fibre reinforced plastic (GRP) was used on both NSP stages, however, since Stage 1’s schedule for installation of GRP was slightly ahead of Stage 2’s, this paper will only focus on Stage 1’s use of GRP.NSP1 involves the construction of 7.9 km of new sewer tunnel ranging in diameter from 1.6 to 2.5 m, five main access shafts at depths of up to 65 m, and connections to the existing sewerage system including several access manholes. Construction began in 2007, and project completion is expected in 2012.The original design for NSP1 specified the use of high-density polyethylene (HDPE-) line precast concrete pipes as the final tunnel lining and HDPE-lined reinforced concrete for the access shafts and manholes. During construction, the rising cost of precast concrete pipes and the introduction of an additional GRP pipe supplier in the market justified a review of the tunnel final lining material. The contractor-proposed GRP pipe alternative was accepted for the final tunnel lining based on time and cost savings that were possible without compromising the design intent. After gaining experience with GRP through this design change, Melbourne Water Corporation reviewed and accepted GRP as the final lining for five smaller connection manholes. The use of GRP for the manholes was particularly inventive as the redesign made use of the approved tunnel GRP pipes as both a structural and corrosion-resistant lining.This paper discusses the use of GRP on NSP1; how the change in material, from concrete to GRP, affected the design philosophies assumed during detailed design; and how construction methods were modified to handle the less rigid GRP material. Details on the structural, hydraulic and durability considerations for the design are included, as are details about the time and cost savings and the quality and safety improvements that were achieved during construction.

Mar 8, 2011

By I D. Gregson, A Gandhe, A S. Garcia, K M. MacAndrew

"Falls of ground still cause around one-third of all underground mining fatalities. The recent introduction of mechanised room and pillar working into Indian coalmines is an example of the application of new design by measurement and safety monitoring strategies, which can be used to reduce falls of ground risks in mines.Rock Mechanics Technology, now part of Golder Associates UK Ltd (Golder), is providing rock bolt support and pillar design services to the mines using a design by measurement approach. This involves in situ monitoring to confirm support and pillar designs and pillar extraction sequences.Site examples are given of the support designs determined and the monitoring programs undertaken for both design and safety.Routine safety monitoring of roof movement using telltales is also described. A new auto warning telltale has been developed specifically to warn of imminent caving as pillars are extracted.The approach used by Golder has played a major role in ensuring the success of these projects. As a consequence, mechanised room and pillar working is now firmly established in India, and wider application is planned to help meet future demand for coal.The experience confirms that the design by measurement method for this application has important advantages over conventional design approaches using analytical or empirical methods. Firstly, it measures the design performance or outcome rather than trying to calculate or predict it. Secondly, it provides the opportunity for the design to be adjusted to obtain the optimum outcome. Thirdly, it can do this at a local level, so that the support design can be matched to changing conditions to give the most cost-effective design. Finally, it incorporates long-term monitoring of support performance, again at a local level, so that subsequent change can be identified to enable corrective measures to be implemented in a timely manner and to ensure that ground control safety is maintained.CITATION:MacAndrew, K M, Garcia, A S, Gregson, I D and Gandhe, A, 2014. Application of design by measurement for support and pillar design in mechanised room and pillar coal mining in India, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference, pp 65–76 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 5, 2014

By Daniel Lozada

La unidad de producción polimetálica de Yauliyacu, ubicada en la localidad de Casapalca, Lima, tiene una presa de relaves en el paraje de Chinchan del mismo departamento. Sin embargo, dado que la presa nueva Yauliyacu culminaría su función y que la presa auxiliar Tablachaca no contaba con la suficiente capacidad de almacenaje, Centromin Perú evalúo otras alternativas para la ubicación y construcción de una nueva. De acuerdo al estudio realizado, se encontró que la quebrada de Chinchan era la más adecuada puesto que ofrecía mayor capacidad de producción y se descartó las de Corina y Tablachaca. En este sentido, el presente texto describe las características de la quebrada, el diseño del depósito de Chinchan, su proceso de construcción, la limpieza de fundación, el análisis de la estabilidad física y química, la implementación para mejorar la estabilidad de la presa, la mejora de calidad del aire en la zona del depósito, el programa de inversiones y el plan de cierre del relave.

Sep 13, 2001

By Henry P. Chandler

THE year 1950 was one of increased activity in almost all branches of the abrasives industry, with nearly all abrasive materials showing a marked increase in tonnage and value. New records were made In the production of tripoli, ground sand and sandstone, pumice and pumicite, and garnet. Total production of crude artificial abrasives in the United States and Canada increased 17 percent in tonnage and 30 percent in value. Imports of industrial diamonds increased 100 percent in total value and 72 percent by weight, the 1950 importation being the largest since 1944. Imports of corundum increased 76 percent in tonnage and 4 percent in value.

Jan 1, 1953

By D. Malovichko

Seismic events and pillar failures observed in two platinum mines in the Rustenburg area, South Africa, were investigated. We studied the sources of approximately 300 largest seismic events recorded in 2009. Moment tensors of these events were estimated from amplitudes and polarities of P- and S-waves. The inverted mechanisms contain isotropic implosive components in many instances. Analyses of uncertainty of the moment tensor solutions confirmed the significance of the implosive component in general. Several documented cases of pillar failure were considered in detail. For each of these a seismic moment tensor was calculated from an elastic stress model assuming an instant removal of a failed pillar. The geometries and magnitudes of the theoretical seismic moment tensors are in agreement with the observed (i.e. inverted from seismic data). The results indicate that either pillar failure or fracturing in the proximity of the reef (within a fraction of the dominant wavelength of seismic waves) are responsible for a significant portion of the large events recorded in these mines.

Jan 1, 2012

By M. A. W. Bryson

Platinum group metals are extracted almost exclusively in South Africa from three very different zones in the Bushveld Igneous Complex, called the Plat, Merensky, and the UG-2 reefs. The Plat reef is currently being exploited only by Anglo American Platinum, whereas the Merensky reef is exploited by them, Impala Platinum, Northam, and Lonplats. The UG-2 reef, on the other hand, is also processed by these producers, but Kroondal and Barplats have operations that exclusively treat ore from this reef. At present the extraction of pgms from ores in South Africa follows the traditional route of upgrading to a concentrate in a minerals processing circuit, further upgrading to a matte in a smelter, and final upgrading and separation of the individual metals in a refinery. Thus all operations that extract pgms require a minerals processing circuit, the design and performance of which is a topic of much interest, as it is a poorly understood and not a very efficient process in relative terms, compared to the other processes. Recoveries across the minerals processing circuit of between 75 and 90% are the norm.

Jan 1, 2004

By H. G. Denkhaus

Please allow me the temerity to reply to your reply to my contribution as follows: A fracture is brittle if plastic deformation is absent or, conversely a fracture is ductile if plastic deformation is present. Consequently, brittleness is specified by the degree of plastic deformation at fracture. This is the generally accepted definition. If other material properties (e.g. the quorient or the product of the uniaxial compressive and tensile strengths) under certain conditions are influenced by brittleness, or brittleness by them, these should not be called brittleness. If the one or the other author does that, he simply uses imprecise language. Even your remark, that ?Inyang and Pitt (1990) stated that the ratio of the compressive strength (sc/st) is directly proportional to brittleness?, confirms that the two quantities are not considered the same. For example:? The well known definition that a material is linear?elastic if the strain is directly proportional to the stress?does not mean that stress (measured in MPa) and strain (measured in %) are the same thing.

Jan 1, 2003

By J. P. Grau, J. Z. Lu

"Thickeners/clarifiers are widely used in coal preparation plants, potash processing and other mineral processing facilities. Thickeners play a very important role in slurry treatment systems to accomplish solid/liquid separation. The demand for larger plants and the increased thickener handling capacities sometime require thickener diameters as large as 200m. The development and use of high capacity thickeners makes it possible to increase the handling capacity of these thickeners by several to more than 10 times compared to conventional thickeners. Hence, for a given slurry rate, selection of a high capacity thickener will significantly reduce the footprint of the thickener. Much higher handling rate, higher concentration of underflow, clearer overflow and lower capital cost are obvious advantages of high capacity thickeners; however, some process requirements and the concerns of operational cost, especially the flocculant cost of a high capacity thickener operation, keep some engineers selecting conventional thickeners and staying away from the high capacity thickeners. Forty years after the first high capacity thickener was developed, there are still arguments in the selection of conventional thickeners or high capacity thickeners in mineral processing. The arguments will continue unless there is a clear picture of capital cost vs. operational cost for each of the thickener types. The purpose of this paper is to analyze these costs and to provide guidelines for selection of thickeners. INTRODUCTIONThickeners/clarifiers are widely used in various slurry treatment systems. For mining and mineral processing, thickeners are an integral part of the solid/liquid separation system. The feed to the thickeners are processing slurries. The fundamental mechanism for the solids/liquid separation is for the solid particles in the slurry to gravity settle inside the thickener tank. The clear water overflows from the top of the thickener tank and is typically reused in the processing circuit, and the concentrated underflow is discharged to different downstream process systems depending on the application of the thickeners. The general requirements for a thickener operation include high density of underflow and clear overflow. Since thickener operation consists of continuous feeding, overflow and discharge of underflow, the solid particles will gravity settle against an upward flow with its velocity dependent on the feed rate and the underflow discharge rate. Higher feed rates to a given thickener produce higher upward velocities. Underflow discharge is typically relatively small compared to the amount of overflow. The upward flow tends to take particles up to the overflow. Only those particles having a settling velocity greater than the upward flow velocity will possibly settle out. Hence, thickener feed rate has to be controlled so that the required overflow water clarity can be achieved."

Jan 1, 2012

Whilst much has been written in past years by geologists, scientists, mining engineers, etc., regarding the well·known and justly notorious anticlinal, or, as they are more commonly known, " saddle" reefs of Bendigo, comparatively little noticehas been given to the synclinal or "inverted saddle "reefs and their relationship with each other. In taking up the question of the synclinal folds, I recognise that it is a large undertaking to confine within the limits of a short paper, and at the same time convey a comprehensive idea of their characteristics, and the importance of their relationship with the anticlinal folds, in the general question of practical mining. However, from a practical point of view I consider the question of great importance, and if an interest in it can be awakened, more particularly among practical men, the object of this paper will be achieved.Before entering into the subject I must briefly state some facts, and perhaps some theories, in respect to the deposition of the Lower Silurian rocks, and their subsequent buckling up, as now seen on the Bendigo gold-field. At the same time, I do not intend to go very closely into the geological aspect of the question, as I wish the paper to be considered as a practical one.

Jan 1, 1902

By L Ventura, M Almond

The Pueblo Viejo project in the Dominican Republic installed an innovative sample system on its reverse circulation (RC) drilling rig during commissioning and subsequent commencement of operations. As knowledge of the orebody increased with mining and plant production, cost pressures became apparent that raised questions concerning the continued use of RC drilling versus blasthole sampling for ore control.To justify the continued use of RC drilling for grade control, an in-depth study was undertaken to determine the quality of the sample and prove its value-add to the operation.To investigate the differences in sample quality, a complete bench trial was initiated across both ore pits to compare RC drill results with blasthole assays on a side-by-side basis. The results indicated that based on ore block comparison between RC and blasthole sampling, RC identified an additional 20 per cent of high-grade (+ 4.5 g/t Au) ounces.Previous work indicated that Au, Ag and Cu were all elevated in the drill fines at Pueblo Viejo (Goers and Almond, 2012). This previous test work did not consider the quantity of fines in an RC sample therefore new test work was undertaken to include particle size distribution analyses. This study would determine if the inclusion of fines in the sample was occurring and compare the quantity of fines in the sample against other sample systems and blasthole samples.Comparisons between RC samples and blasthole samples indicate that for the RC samples a range of 30–35 per cent of the sample passed 300 mesh as compared to blastholes where the range of the sample passing 300 mesh was 15–30 per cent.This paper includes a case study on the importance of accurate samples and how they have impacted throughput through the pressure oxidation process plant at Pueblo Viejo. The accurate samples provided by RC allow for improved stockpile and blending strategies, showing the importance of accurate samples to manage risk and create value, against the perception that savings can be made at the risk of poor sampling performance.CITATION:Almond, M and Ventura, L, 2017. Adding value with reverse circulation drilling at Pueblo Viejo, in Proceedings Tenth International Mining Geology Conference 2017, pp 277–284 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By R. Altindag

In rock cutting mechanics, the effects of the rock and coal brittleness on the efficiency of cutting bits are examined by many researchers. There is no universally accepted brittleness concept as a measure of cutting efficiency. The effect of the brittleness on rock cutting has not been completely explained. The aim of this study is to correlate the relationships between Specific Energy (SE) and brittleness concepts. The applicability of various brittleness measurement methods for rock cutting efficiency has been investigated. In this study, the raw data derived from previous experimental studies were used, and the relationships between SE and brittleness concepts were investigated. The two previously used brittleness concepts, which are named as B1 (the ratio of compressive strength to tensile strength) and B2 (the ratio of compressive strength minus tensile strength to compressive strength plus tensile strength), and a new introduced brittleness concept named B3 (the area under line in relation to compressive strength and tensile strength) were evaluated in this study. The relations among these brittleness concepts for rock cutting efficiency were established using regression analysis. There is no correlation found between the SE values and the brittleness of B1and B2values. But, the SE is strongly correlated with the brittleness of B3. It was seen that the suggested brittleness of B3concept could be used as an indicator in rock cutting efficiency analysis.

Jan 1, 2003

By C. Bryce

Rhenium is primarily recovered as a by-product from molybdenum roasting circuits. However, rhenium is also present in copper heap leach solutions at very low concentrations and represents a potential new rhenium source. Freeport-McMoRan Copper & Gold has developed a new process using carbon adsorption followed by ion exchange or solvent extraction to concentrate rhenium from less than 1 ppm to 15 g/L. The product is compatible as a feed to an existing rhenium processing plant. A pilot plant operated at Freeport-McMoRan?s Sierrita mine has demonstrated the technical and financial feasibility of this new process.

Feb 23, 2014

By David Newman

Multiple seam underground coal mining is ubiquitous in Appalachia. Many coal properties have from two to ten or more economically mineable coal seams. Because of the ability to penetrate 600-feet to 1,000-feet or deeper into the mountainside leaving panels of web pillars separated by barrier pillars, highwall mining is a hybrid between surface and underground mining. As a result, many of the ground control problems commonly associated with multiple seam underground mining exist with multiple seam highwall mining. These include: i) superjacent mines, subsidence and caving propagating to overlying seams and ii) mines, pooled water and the potential for inundation resulting from a iii) breakthrough between an active highwall mine and abandoned underground mines in the same or superjacent seams, the presence of overlying or underlying mine workings where iv) pillar columnization in the active mine is not possible, and v) the question of whether to mine ?top-down? or ?bottom-up.? Case histories are presented from southeast Ohio where the Middle Kittanning No. 6 and Lower Kittanning No. 5 seams are successfully highwall mined with 20-feet to 40-feet of largely shale interburden. A highwall miner was caught in a highwall collapse in the Middle Kittanning No. 6 seam when it was overmining auger workings in the Lower Kittanning No. 5 seam. Multiple seam interaction caused by the overmining transferred overburden stress onto the Lower Kittanning No. 5 seam. The overburden concentrated through web pillars initiated auger web pillar failure, resulting in roof collapse and subsidence in the Lower Kittanning No. 5 seam that propagated up to the Middle Kittanning No. 6 seam. A second case history involves multiple seam highwall mining in southeast Kentucky. The A3 Rider, A3, B2, and C1 seams are being highwall mined around abandoned underground mines in the A3 and B2 seams and augering in the A3 Rider. Because of spoil storage constraints for the surface contour mines, the highwall miner follows the active pits in each seam so a standard sequence of ?top-down? or ?bottom-up mining does not exist. The planning and engineering design considerations associated with each case history is presented along with geotechnical information. In the case of the highwall collapse a back analysis is presented of the stability and safety factors for the auger webs, highwall miner web pillars, and barrier pillars.

Jan 1, 2009

By D. deV. van der Spuy

A procedure for optimizing the secondary cooling zone of continuous casters is proposed and illustrated by a billet caster example. The procedure consists of quantifying deviations from the required conditions of the secondary cooling zone?as far as temperatures, metallurgical length and reheating are concerned?by means of a ?cost function?. The optimal spray settings are then found by minimizing the total ?cost?. The billet caster examples serve to emphasize the importance of specifying the required conditions in a consistent manner. Some envisaged practical limitations of this approach are discussed.

Jan 1, 1999

The effect of composition on electrical conductivity (resistivity), viscosity and liquidus temperature of the slags encountered in electric smelting of PGM containing suphide concentrates is reviewed, along with the relationsip between slag composition, slag-matte separation and metal losses to slag. Optimization of slag composition at furnace temperature is attempted on the basis of opposite and parabolic trends of the viscosity-conductivity relationships of the slags. The importance of surface tension of slags is emphasized using available and estimated information which are grouped into a useful correlation. These values are coupled with or incorporated into slag viscosity plots to illustrate the correlation between the two factors, which influence slag-matte separation as well as refractory attack. The electrode in the slag-resistance furnace is the central factor in the design and operation of the furnace by its role of conveying the smelting power. The obvious parameters are the size and positioning in the slag bath, which are defined by slag resistively, furnace resistance, cell constant and power input. The flow of heat generated by the electrode current determines the energy distribution and furnace dimensions creating viscosity profiles, which in turn affect flow conditions. Thus the flow of slag and matte are discussed in conjunction with the furnace geometry, stirring action of the electrodes, buoyancy and electromagnetic effects. The action of the electric furnace as a settler is discussed. The rectangular furnace is considered as a channel reactor in this analysis, and the action of the electrodes is described to indicate a balanced settling rate in the area of electrode action. Discussion of the design and production capacity of the electric furnace, with reference too perating current, power input, furnace dimensions and electrode size, are based on considerations derived mainly from slag properties such as its resistively, viscosity and liquidus temperature.

Jan 1, 2004

By K. Duckworth

"Comparative tests of the conventional Turam survey configuration and an alternative configuration called the Tx-parallel configuration were conducted at the McClean uranium deposit in northern Saskatchewan. Both configurations detected the known conductors at the site but the alternative configuration demonstrated its particular effectiveness in the reconnaissance role. This effectiveness results from the fact that the length of Tx-parallel traversesis controlled only by the length ofthe transmitter and not by its power. In addition, the field strength along a Tx-parallel traverse is uniform unless the traverse approaches the end of the transmitter. This freedom from a strong gradient of the primary field along a Tx-parallel traverse eliminates the gradient-induced anomaly shifts which are common in conventional Turam operations. The locations of each of the McClean conductors, that were obtained from the Tx-parallel profiles, werein better agreement with the locations known from drilling than were the locations obtained from the conventional profiles. However, the conventional profiles gave better estimates of the conductance of the targets.The results obtained over the McClean conductors indicate that current gathering has a strong influence on Tx-parallel results with consequent unpredictable influence on depth and conductance estimates. However, the depth estimates obtained from the Tx-parallel data appear to be in good agreement with the known depth of the McClean south conductor. The Txparallel results provide shallow estimates of the depth of the McClean north conductor which suggest that the fracture zone above the graphitic conductor is a significant conductor as was also suggested by earlier VLF surveys.Comparison with the wide range of published geophysical test surveys for the McClean site showed that apart from the work required to lay the transmitter, the Tx-parallel mode of operation of a Turam exploration system is operationally very similar to a moving source Slingram type of survey. At the McClean test site, it provided the same depth of exploration as a conventionally deployed fixed loop transmitter."

Jan 1, 1988

By Bill Parnell

"Friction winders and double drum winders have been used in the vertical shaft mining industry for over 100 years. In that time, there have been many changes made in the electronic and mechanical fields of hoisting, but few changes made in the manufacturing and performance of steel wire rope, until recently.In the past ten years, with the advent of high polymer thermoplastics, the industry has seen some major advancements in steel wire rope. By incorporating a polymer with steel, improvement of rope life and reduction of costly maintenance downtime has been accomplished.IntroductionThe Williams Mine is Canada's largest gold producer with an annual production of some 500 000 ounces of gold from 2.2 million tonnes of ore. The Williams Mine is situated in the Hemlo area of northwestern Ontario, approximately 40 Ian east of the town of Marathon. It is operated by the Williams Operating Corporation which is owned equally by Teck Corporation and Homestake Canada Inc. It is one of three adjacent properties forming the Hemlo gold camp."

Jan 1, 1995