Search Documents

By Hayel M. El-Naggar, Sherif A. Akl

Although grouted piles have been used for several decades since the idea was proposed in the 1970s, their design is mostly based on experience and unpublished proprietary methods. There is little research on grouting drilled shaft tips and even less on grouting shaft sides. This paper presents the analysis of 4 instrumented pile loads tests on base and shaft grouted piles from different sites in Egypt; with emphasis on one of the tests, to demonstrate the analysis process. The data from the tests are analyzed to model the development of unit side friction (USF) with relative displacement. A numerical model using the finite element software PLAXIS is used to investigate the effect of grouting on the surrounding soil stress state. The paper combines the observations from full scale pile load tests and results from the numerical model to suggest an idealized behavior of side friction development with relative displacement of the grouted part of the shaft. The suggested model considers an envelope of Unit Side Friction (USF) with relative displacement, initially dominated by the grout resistance then at higher relative displacements, the friction with radially pressured soil takes over. The grout provides very high USF values up to a relative displacement of 2mm. Then, the USF drops to a typical pile soil side friction behavior; however, this friction is affected by the contact stress between pile and soil, which significantly increases due to compaction grouting. INTRODUCTION Base and shaft pile grouting has been significantly developing in recent years to accommodate the unfavorable conditions in major projects such as the high loads in high rise building and founding on problematic soil formations. Grouting aims to decrease settlements and increase the capacity of the pile under axial load. The technique is first introduced by Kraft (1974) but gained popularity in the 1980s. Typically there are two types of grouting; compaction, and permeation. Compaction grouting is more common in pile foundations practice, and many researchers have provided case histories of pile load tests on base grouted piles and base and shaft grouted piles (Gouvenot and Gabaix,1975; Stocker, 1983; Ghazali et al., 1988; Fleming, 1993; Kusakabe et al., 1994; Robson and Wahby,1994; Joer and Randolph, 1998; Hamza and Leoni, 1998; Mullins et al. 2000; Littlechild et al., 2000; Suckling and Eager, 2001; Dapp and Mullins, 2002; Ho, 2003; Fu and Zhou, 2003; Brettmann and NeSmith, 2005; Ruiz, 2005; Mullins, 2006; Dapp and Brown, 2010; Beadman et al., 2012; Nguyen et al., 2013; Miller et al., 2013; Sinnreich and Simpson, 2015; Hui and Lin, 2015). Compaction grouting is meant to densify the soil around the pile and below the base rather than permeate this soil and increase its cohesion. Research showed that grouting increases the capacity of the piles by a factor of 2~5. The variation in capacity increase depends on pile type, grouting process, and especially grouting pressure. Although there are many case histories of pile load tests on grouted piles but there is no well-defined agreed-upon method to predict grouted pile capacity as typically done in ungrouted piles. Few lab experiments discussed the shaft grouting effects on the soil especially the compaction grouting. The experiments concluded that the compaction grouting forms a homogeneous layer between the pile and the soil, and a residual effective stress is achieved simultaneously with a significant densification of the soil around the pile with noticeable decreasing in void ratio. (Fattahpour et al., 2015; Wang et al., 2015). Recently, studies used numerical analysis to investigate the behavior of the grouted piles and the changes in the surrounding soil (Chiang et al., 2013). That study presents a simulation of the base pressure grouting with a simple FE model and predicts the reduction of the pile settlement by 10 to 20%. Another numerical study using a complex model conducted by Zhou et al. (2017), pr

Jan 1, 2018

By J E. Wajon

This paper discusses the background, requirements, need and content of plans for management of drinking water self-supplied to mining-related operations, including construction camps, especially in remote areas of Western Australia. The paper discusses the importance of cooperation between regulators, the mine site operator and the consultant in preparing a plan fully compliant with the Australian Drinking Water Guidelines to protect the quality and safety of drinking water supplied to mine sites. The paper outlines some of the issues that need to be addressed in preparing a drinking water quality management plan, such as hazard identification, risk assessment, the multiple-barrier approach and the concept of critical control points. Data requirements, monitoring, incident management, training and reporting are also covered.CITATION:Wajon, J E, 2013. Drinking water quality management for mining operations in Western Australia, in Proceedings Water in Mining 2013 , pp 321-328 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By D Hume

During 2001 the Ridgeway Gold Mine, driven by company initiatives and recent NSW legislation (General Rule 2000), developed and implemented Major Hazard Management Plans to control significant hazards identified at the underground mine. The paper presents the objectives, issues, outcomes and process involved in the development and implementation of the plans at Ridgeway. The sharing of the experience gained and an overview of the intended way forward will offer a valuable insight for other mines considering embarking on a similar journey.

Jan 1, 2002

By Jack W. Carlson

Considering the magnitude of today's public concern with critical mineral and fuel materials, regarding both their midterm and long term availability, the Nation is fortunate to have in place and operating the coordinated data systems of the Geological Survey and the Bureau of Mines. Under the supervision and policy direction of the Assistant Secretary--Energy and Minerals, these Department of the Interior agencies have long been responsible for important mineral activities in the Federal Government. Aside from their highly respected mineral industry publications such as the monthly Mineral Industry Surveys, annual Commodity Data Summaries and topical Professional Papers and Reports of Investigation, the Bureau of Mines and Geological Survey data bases and expertise have been readily available for use in emergency situations. Policymakers and decisionmakers in government have placed major reliance upon this ready mineral data and analytical capability in World War II, the Korean War, the recent price control era, and the Arab oil embargo.

Jan 1, 1975

By Kazutoshi Haga, Batnasan Altansukh, Atsushi Shibayama

In this study, the dissolution behavior of copper and arsenic from five different copper concentrates containing 21-34.7 %wt. of Cu, 1.3-7.3 %wt. of As and 15.6-27.5 %wt. of Fe were investigated under high pressure oxidative leaching conditions. Leaching experiments were conducted using different leaching reagents such as ferric sulfate, sodium chloride, deionized water, sulfuric acid and ferric sulfate-sodium chloride mixture in order to compare the effectiveness of each on the dissolution of copper and arsenic from copper concentrates. The effects of ferric sulfate (0.1-1 mol/L), sodium chloride (0.1-0.5 mol/L) and leaching temperature (100-180C) were investigated under 1 MPa autoclave pressure , particle size >45 m, pulp density of 100 g/L, stirring speed of 750 rpm and leaching time of 60 min. Results showed that the most effective leaching reagents for the dissolution of copper are 0.34 M NaCl and a mixture of 0.1 M Fe2(SO4)3 - 0.34 M NaCl, in which As extraction did not exceed 7%. The copper concentration in the pregnant leach solution obtained after leaching using 0.1 M Fe2(SO4)3 - 0.34 M NaCl was 13-30 g/L, while the concentration of As and Fe were in a range between 0.3-1 g/L and 0.2-10 g/L at 160C. INTRODUCTION Copper sulfide minerals, such as chalcopyrite (CuFeS2), chalcocite (Cu2S) and covellite (CuS) are used for the production of copper in mining and metallurgical industries worldwide. The conventional pyrometallurgical processing followed by electrorefining is a common process for the production of high purity copper (Moskalyk, & Alfantazi, 2003; Padilla, Aracena, & Ruiz, 2012). However, the degradation of copper content and an increase in the amount of metal impurities, especially arsenic (As), antimony (Sb) and bismuth (Bi) in copper concentrates cause serious problems to the production of copper and environmental pollution (Basha, Selvi, Ramasamy, & Chellammal, 2008; Long, Peng, & Bradshaw, 2012). Hydrometallurgical processes are used to recover metals from refractory ores, concentrates and tailings by leaching (Long, Peng, & Bradshaw, 2012; Masloboev, Seleznev, Svetlov, & Makarov, 2018). During the last decades, hydrometallurgical processing for the recovery of copper from enargite-bearing copper ores and concentrates has been extensively investigated due to its relatively more environmentally benign and less capital costs than the conventional pyrometallurgical processes (Long, Peng, & Bradshaw, 2012; Masloboev, Seleznev, Svetlov, & Makarov, 2018; Choubey, Lee, Kim, & Kim 2018). However, several issues facing the hydrometallurgical processing are incomplete extraction of copper associated with the coprecipitation of iron compounds, difficult stabilization of toxic impurities and production of a contaminated copper product (Dreisinger, 2003; Safarzadeh, Moats, & Miller, 2014). Hence, a number of studies have been conducted on the selective dissolution of copper from copper ores and concentrates or selective removal of arsenic leaving a clean copper residue using various leaching reagents or lixiviants (Safarzadeh, Moats, & Miller, 2014; Mihajlovic, Strbac, Zivkovic, Kovacevic, & Stehernic, 2007; Tongamp, Takasaki, & Shibayama, 2009). More extensive studies on the selective extraction of copper from enargite- bearing copper ores and concentrates are much needed to improve copper recovery.

Jan 1, 2019

By Kray Luxbacher, Mario Karfakis, Erik Westman, Peter Swanson

Three-dimensional velocity tomograms were generated to image the stress redistribution around an underground coal longwall panel to produce a better understanding of the mechanisms that lead to ground failure, especially rockbursts. Mining-induced microseismic events provided passive sources for the three-dimensional velocity tomography. Surface-mounted geophones monitored microseismic activity for 18 days. Eighteen tomograms were generated and high-velocity regions correlated with high abutment stresses predicted by numerical modeling. Additionally, the high-velocity regions were observed to redistribute as the longwall face retreated, indicating that velocity tomography may be an appropriate technology for monitoring stress redistribution in underground mines.

The U.S. National Institute for Occupational Safety and Health (NIOSH) conducted a study to determine the effectiveness of a filtered air delivery system to reduce respirable dust exposure of roof bolter operators in underground coal mines. When performing roof bolting operations, roof bolter operators may experience exposure to high levels of respirable dust during a working shift, especially when working downwind of the continuous mining machine. While drilling and installing roof bolts, this filtered air system supplies a clean curtain of air over the roof bolter operator by means of a plenum mounted beneath the canopy. This experimentally designed air curtain, adapted for roof bolting machines used in this study, is based upon previous design prototypes, computational fluid dynamics (CFD) simulations and trial-and-error testing. Both the prototype and final designs were tested in the full-scale mining galleries at the Office of Mine Safety and Health Research (OMSHR) in Pittsburgh, PA before being taken underground for field testing. Test results of the system in both laboratory and field studies show reductions in operator exposure to respirable dust when the operator is positioned directly under the protected zone of the canopy.

Jan 1, 2012

By Forrest T. Moyer

To keep the mineral and allied industries informed of trends in the causes of accidents and to point out the need for corrective measures, the Bureau of Mines collects, analyzes, and periodically published health and safety statistics. This report includes data for 1964 on injury experience, with related employment statistics, at coal mines in the United States. These data are presented in tabular form under the following headings: General Injury Experience Tables 1 to 6: Current data on number of injuries, degree of injury, frequency and severity rates, average severity, and related employment and production data by work location.

Jan 1, 1967

At the Prospectors and Developers Annual Convention (PDAC) in Toronto, Canada mining and exploration companies of all sizes were on hand to discuss the year that was and those that will be. The following is a look at some of the companies with Canadian operations that were on hand for PDAC 2009. Iamgold Corporation is a leading mid-tier gold mining company producing approximately 31 t (1 million oz) of gold from seven mines on three continents. With record revenues of $870 million ? up 28 percent when compared to 2007 ? the company is focused on growth with a target to reach 56 t (1.8 million oz) gold production by 2012. During 2008, the company acquired the Essakane project in West Africa. The project is fully permitted, under construction and will contribute more than 9.3 t (300,000 oz) of lower cost production by late 2008. Iamgold increased its reserves by 55 percent, to 385 t (12.4 million oz) and its resources in-creased by 16 percent to 821 t (26.4 million oz) in 2008. Going forward, Iamgold has three areas of focus ? West Africa, Guyana Shield and Quebec ? with seven gold operations, five advanced projects and the Niobec niobium mine included. The Rosebel Mine in Suriname is Iamgold?s fl agship property. With measured and indicated resources of 300 t (9.6 million oz), it accounts for 30 percent of Iamgold?s production. Production there was up 20 percent compared with 2007 and further production increases are expected in 2009 and 2010. Mill expansion and optimization increased throughput from 8.9 Mt/a (9.8 million st) to 10 Mt/a (11 million stpy). In West Africa, Iamgold has joint ventures at Sadiola in Mali; Tarkwa in Ghana; Yatela in Mali and Daman in Ghana. Iamgold also has 100 percent ownership of the Mupane gold mine in Botswana and the Doyon gold mine in Quebec, Canada. Also in Quebec, Iamgold has 100 per-cent ownership of the Niobec niobium mine in Quebec. Niobium is used in high strength specialty steels.

Jan 1, 2009

By Robert E. Hershey

1. This investigation shows that the most important beds in Claiborne County, from the standpoint of present production and reserves, are the Coal Creek and Jellico. Together, they contain 69 percent of the known recoverable reserves in the county. Reserves in five other beds are tabulated in this report; in order of quantity of reserves, they are: Blue Gem, Lower Pioneer, Pewee, Big Mary, and Rex. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and on 1,800 short tons per acre-foot of coal in place, are estimated to be 60 million tons, as of January 1, 1953. Of this total, 55 million tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager to permit making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1956

A general description of investigative work conducted by the Bureau of Mines at the, Missouri Valley. manganese deposits and leading to tonnage and grade estimates has been given in Report of Investigations 4375, part 1 of a three-part report of work done between July 1945 and August 1947. Basic factual information from which tonnage and grade estimates were drawn was derived through the drilling sampling of 238 large-diameter bucket-drill holes in 11 widely separated areas. Drilling areas were selected after careful reconnaissance, mapping, and consideration of earlier work done on the deposits by the Bureau of Mines, State agencies, and private organizations and individuals. Stratigraphic studies permitted extending the results compiled within the drilling; areas to outcrop and lightly covered manganiferous zones between an beyond drilling areas. The locations of drilling areas, drilling sections, and individual drill hues are shown on illustrations in part 1 f this report. The individual drill holes, aside from providing the basic information for tonnage and grade estimates, disclosed features affecting any future plan As exploitation. It in particularly significant that a large part of the visible outcrops is faulted end otherwise complicated by slides that give a false impression of the thickness, vertical location, and even the existence of manganese-bearing zones.

Jan 1, 1949

By Robert H. Peters

The objective of the project descibed in this report was to design and field test a model health and safety program at a coal mining company and a gold mining company. The model program was implemented primarily by providing training on loss control, accident investigation, and the operation of mobile equipment; and by providing technical assistance to help solve health and safety problems. Data were obtained from company records on occupational injuries, illnesses, accidents, and "near misses"; and through direct observation of employees performing a large number of randomly selected jobs. At the coal mine, employees were observed five times over a 15-month period. At the gold mine, employees were observed six times over a 16-month period. During the study, the percentage of sampled jobs containing one or more safety deficiencies decreased from 74.3 pct to 36.6 pct at the coal mine and from 86.4 pct to 19.1 pct at the gold mine. Work on this project was performed by Woodward Associates, Inc., under a Bureau of Mines contract.

Jan 1, 1986

By Frank B. Fulkerson

Three of the five primary aluminum producers in the Pacific Northwest have facilities in the region to make aluminum mill products. Only one of the three, however, produces a variety of shapes and forms. The principal reason for the lag in development of an aluminum mill products industry was found to be transportation cost. The long range outlook is for expansion, based mainly on growth of the western market for aluminum used in construction, containers and packaging, electrical applications, diesel trucks, mobile homes, and irregation pipe. Consumption of western aluminum mill products in 1985 is projected at 1.1 million tons, compared with estimated consumption of 250,000 tons in 1961.

Jan 1, 1965

By R. W. Chappell, M. W. Hills, R. L. Olsen

A stochastic approach was developed and applied to the Butte, Montana Hillside abandoned mining site for modeling stormwater runoff and subsequent receiving stream loadings. This approach enabled capture and quantification of the uncertainty associated with stormwater quality data and allowed the prediction of copper and zinc concentrations in the receiving stream caused by runoff from the Butte Hillside during storm events. Runoff flows and stormwater concentrations were input to the model as probability distribution functions. Monte Carlo simulation allowed prediction of expected instream concentrations in the form of cumulative distributions functions. The modeling results allowed evaluation of current best management practices (BMPs), targeting of future BMPs, and identification of key data gaps to fill during future sampling activities. This modeling approach is considered extendable to other active and inactive mining sites. Output from a model of this type is easily understood and can be used to communicate effective stormwater management to site regulators. Furthermore, application of this modeling approach will facilitate the development and implementation of a site-specific stormwater management plan and will optimize efforts to achieve standards for compliance with stormwater discharge permits.

Jan 1, 2002

By I F. Bell, K P. Hammerschmid

Well planned and executed environmental management plans can reduce life-of-mine operating costs and the need to deal with major environmental issues at the time of mine closure. With proper planning during the exploration, feasibility and execution phases of a project, final closure costs can be reduced. The reduction of closure costs should be considered during exploration and initial feasibility studies and when process facilities, waste rock dumps and tailings impoundments are designed. During the mining of the resource, closure cost reduction will depend on effective and efficient environmental management plans for ongoing land clearance, segregation of mine waste materials, management of mine site water and workshop wastewaters, and the establishment of progressive rehabilitation strategies. These issues are the responsibility of planning, production, technical support and maintenance personnel at an operating site. The successful implementation of environmental plans will ensure that all impacts are reduced and that closure issues with major cost implications are addressed prior to closure of the mine.

Jan 1, 1995

By Karen Mikkola, Gerald Luttrell, Jaisen Kohmuench, Glen Oswald, Michael Mankosa, Tracy Westerfield

Hydraulic separators are commonly used for particle size classification and gravity concentration of minerals and coal. Unfortunately, the efficiency of these processes can be quite low due to poor equipment design and variations in feed consistency. To help alleviate these problems, an industry-driven R&D program has been undertaken to develop a new generation of hydraulic separators that are more efficient and less costly to operate and maintain. Two of the most promising technologies, the CrossFlow and HydroFloat separators, have now been tested at industrial sites. The data obtained from these sites have been used to illustrate the potential performance improvements that can be realized through the application of these high-efficiency separators.

Jan 1, 2005

By Balu E. George, Subhadeep Banerjee, Shailesh R. Gandhi

"A three-dimensional analysis of laterally loaded helical piles installed in cohesionless soil is presented. Finite Element Analysis was conducted using commercially available Plaxis 3D AE version, assuming Mohr-Coulomb failure for soil. Pile is modelled as plate elements with a single helical blade attached to a hollow shaft. The ultimate load for various configurations is examined considering deformation criteria. The Bending Moment distribution and maximum lateral deflection are also discussed. It was observed that the ultimate lateral load carrying capacity increased by presence of helical blade and the maximum deflection also got reduced. The diameter of the helical blade was found to have significant effect on the lateral deflection, maximum bending moment and the ultimate load. However, the observations from the study suggest that the presence of helical blade seizes to produce considerable effect after a certain depth. Difference in failure pattern with regard to the distribution of soil resistance observed for different geometries considered for numerical analysis are also touched upon.INTRODUCTIONHelical piles or screw anchor piles have gained popularity due to fast installation, instant use, and other advantages over the traditional piles. They are usually used to support structures like solar panels, light houses, and other light structures which are subjected to uplift loads. However, such structures are often subjected to significant lateral loads as well. Under lateral loads, the response of helical piles can be different from that of a conventional pile due to the presence of the bearing provided by the helical blade. However, the proper design remains a concern due to lack of work carried out on the lateral capacity of helical piles.The lateral performance of helical piles is significant because they can act as efficient alternative to conventional piling systems in many applications.The lateral load capacity of screw anchor piles with different number of helices were examined by Mittal et al. (2010) by experiments in sand. They found that the lateral load capacity of piles increases with addition of helical blades. Prasad and Rao (1996) examined the lateral capacity of helical piles in clay by experiments on model piles and found that the lateral capacity of helical piles were more than that of the straight shaft piles. It was observed that the lateral capacity increase with embedment depth and shear strength of soil. Sakr (2009) studied lateral performance of two section helical piles in soft soil. The investigation by Prasad and Chari (1999) reported that the pressure distribution across the diameter is not uniform for circular piles, but it is maximum at the centre and almost zero at the two edges.Puri et al. (1984) after conducting model tests on single-helix, two-helix, and three-helix anchors installed in sand, proposed a mathematical model that was fashioned after Matlock and Reese’s elastic theory model. Elkasabgy and Naggar (2015) investigated he lateral performance of full scale large capacity helical piles in structured cohesive soils and reported the modulus of sub-grade reaction to be non linear."

Jan 1, 2017

By R. L. Bolmer

Rapid depletion of our known mineral resources has stimulated exploration for new mineral deposit. Abandoned mines or prospects may prove to be commercial in today's economy. Often it is necessary to revaluate such properties. Some of these may be inaccessible because of caving of flooding. Many, however, remain in good condition, except that over the years the air in the workings has become depleted of oxygen. Each year the Bureau of Mines receives numerous requests for aid in entering old mines, the air in which is incapable of supporting life. Requests of many individuals who wish to examine or explore-such places with the help, of the Bureau's self-contained oxygen breathing apparatus have been denied because of the hazards involved in the use of this equipment for such purposes. The distance to be traveled in irrespirable gases may be too great for safety; under favorable conditions, a round trip of 2,000 feet from fresh air is the maximum distance that may be traveled.3/ The use of such equipment is hazardous unless a team of at least 5 men thoroughly experienced in its use is provided; and when extensive traveling from. a fresh-air base is required, a reserve team should be provided.3/ Usually, the apparatus is requested for use in exploring workings having only one surface connection, as mines having more than one opening usually are more easily ventilated;,and in some natural ventilation is sufficient or can be made so by cleaning out obstructed openings.

Jan 1, 1951

By R. B. Toombs

In describing the Canadian mineral industry in a world setting, this paper examines the industry from four points of view. First, mineral industry growth is related to trends in economic activity thereby providing a measure of the industry's importance in the Canadian economy. To give perspective to the Canadian scene, reference is made to economic trends in several of the world's leading mineral producing and mineral consuming countries. The Canadian mineral industry is next examined in terms of its major developments of the past 20 years and the resultant size, structure, and production diversity of 1964. The position of the Canadian mineral industry in the world industry is then analyzed by tracing changes in mineral supply and demand patterns. Growth of the Canadian industry depends greatly on expansion of export markets because three fifths of the value of production is accounted for by exports. Finally, attention is directed to the outlook for the Canadian mineral industry. Problems facing the industry are surveyed, and an appraisal is made of economic policies that have encouraged industry growth. A forecast of mineral production value in 1970 is included.

Jan 1, 1964

By S. C. Gouws

"SynopsisSustainable infrastructure development has long been identified as a key enabler for socio-economic growth and poverty reduction in societies globally. Twenty-one years into the young South African democracy, economic prospects are fragile and unemployment statistics are high. According to Trading Economics (2015) the GDP growth rate in South Africa averaged 3.07% from 1993 until 2015.Through the National Development Plan 2030, the government has responded by instituting the Presidential Infrastructure Coordinating Commission (PICC) to direct national growth and drive job creation by effecting a long-term infrastructure investment programme. The Commission is mandated by Cabinet to coordinate, integrate, and accelerate implementation of more than 150 individual social and economic infrastructure plans.In the civil infrastructure development sector, increased urbanization is compelling governments and the public sector to expand safe and reliable public amenities, but the availability of real estate for construction in congested cities is a challenge. Within the mining infrastructure construction industry safe, rapid, and efficient mine extraction strategies are imperative to realize increased production, business hurdle rates, and stakeholder expectations.Asset owners and stakeholders are obliged to consider advanced mechanized underground excavation and support technologies in order to present feasible solutions timeously. From an engineering design, procurement, and construction management (EPCM) perspective tunnelling technology and boring applications have a distinct advantage over conventional excavation techniques. These solutions may enhance commerce and transportation by expanding infrastructure in concentrations of national economic activity, providing crucial linkages with rural areas, between cities, and across international borders.This paper explores the contribution by mechanized tunnelling technology and boring applications applied in conjunction with digital and automation technologies compared with conventional methodologies. The technological expertise, combined with a paradigm shift in delivery of project objectives, will promote economic growth, aid recovery from the economic downturn, and improve social development."

Jan 1, 2015