Search Documents

By Moi Arzamendi, Jose Ramirez, Kenneth Kniss, Sunil Arora, James Gingery

Construction of a new approach embankment for a railroad bridge over a river in Southern California required placing up to 12 ft of fill over soft to medium stiff silts and clays along an approximate 1,500-ft long stretch. The embankment, situated within a narrow railroad right-of-way between an existing live track and existing buildings, would have been susceptible to excessive settlement that could damage existing buildings and numerous underground utilities if regular weight soil fill had been placed over the unimproved ground. To limit total and differential static settlements to tolerable levels, a design was developed using a combination of mechanically stabilized earth wall with lightweight cellular concrete fill and rigid inclusions ground improvement. This paper describes the design of the ground improvement system, construction methods used, and challenges of working next to live railroad traffic. Ground improvement quality control and assurance measures, and verification of performance by settlement monitoring are also addressed. INTRODUCTION AND BACKGROUND The 0.9-mile San Diego River Double Track (SDRDT) project is located on the Los Angeles-San Diego- San Luis Obispo (LOSSAN) Corridor in San Diego, California. The project includes the replacement of the existing 900-ft long single track railroad bridge over the San Diego River with twin double track structures. Construction of the project is phased and closely coordinated with the associated Mid-Coast light rail project (San Diego Trolley Blue Line Extension). The new bridge is a 7-span, twin steel, through girder structure supported by six cast-in-place reinforced concrete pier caps and two abutments. The large diameter cast-in-drilled-hole (CIDH) foundations are up to 9 ft in diameter, with upper portions encased in a 1.5-in.-thick permanent steel casing. The north abutment approach embankment includes a mechanically stabilized earth (MSE) retaining wall up to approximately 10 ft high and 1,520 ft long. This paper focuses on the design and construction of the north approach embankment. The project site is characterized by challenging geotechnical and seismic conditions. The site contains liquefiable soils interbedded with soft cohesive soils, underlain by competent layers of sand/gravel/cobble and other sedimentary formations. Static settlement of the new railroad, crossing utilities and adjacent buildings was a primary design concern for the north approach embankment.

Jan 1, 2018

By Skinner. W.

"Introducing cutting-edge development work, which aims to simplify mineral processing flow-sheets, reduce costs and address environmental issues. Over the past four years Innovative Mineral Processing Technologies Pty. Ltd (IMPTEC) Australia have developed a Super-fine Crusher and a Planar Magnetic Separator which offer low cost, wet or dry alternatives to conventional grinding and conventional magnetic separation. Each of these machines has been successfully trialed at pilot scale and are now in the process of transitioning to commercial scale. This paper reports on the progress made in each of these fields. The potential scope for application of super-fine crushing technology as an alternative to grinding is potentially expansive and could include beneficiation of metalliferous ores, precious metal ore processing, hydrometallurgical processing, industrial minerals and coal processing, plastic fillers and ceramics processing as well as processing of cementitious slags and fly-ash. IMPTEC have recently achieved outstanding results at pilot scale with a dry combination of super-fine crushing and planar magnetic separation, which offers an alternative to the wet processing of magnetic iron ores. The dry combination has set new laboratory performance benchmarks when compared with the industry standard wet Davis Tube Tester. The test results have also established a strong evidence base showing that super-fine crushing achieves liberation of value minerals at coarser sizes when compared with grinding. The dry combination of super-fine crushing and planar magnetic separation also addresses environmental issues and completely eliminates grinding. An IMPTEC super-fine crusher is currently undergoing commercial trials, generating ultra-fine products from granulated lead blast furnace slag for use as cement substitutes. The performance of the super-fine crusher on this extreme duty highlights the potential benefits of super-fine crushing over the wide range of industries and applications where conventional grinding is employed.INTRODUCTION Present day mineral processing practices can become anchored in convention, where, inefficient methodologies are recognized and accepted as “best practice” or “industry standard”. Motivated by this challenge, IMPTEC has undertaken the development of radically different and improved methodologies in the fields of fine comminution and magnetic separation. Whilst, crushing is much less energy intensive and generally less capital and maintenance intensive than grinding, the technology has stalled due to the lack of crushing devices, which have the capacity to adapt to fine and ultra-fine duties. Grinding practice advances have been achieved through major increases in machine size and power. However, these advances are also accompanied by major escalations in capital, operating and maintenance costs. The economics of this strategy has become increasingly questionable. A typical example is the viability of low-grade magnetite beneficiation, which can hinge largely on the cost of grinding to fine and ultra-fine liberation sizes."

Jan 1, 2018

By Ata Akcil, Z. B. Karshigina, Ye. G. Bochevskaya, E. A. Sargelova, Z. S. Abisheva

Phosphorus slag is one of the most large-tonnage of yellow phosphorus production waste, which for decades stored in the slag disposal, by polluting the environment and creating environmental problems in the regions. Phosphorus slags from the processing of Karatau phosphorites are a very promising source of raw materials not only for silicon compounds but also rare earth metals (REM). Among the REM, yttrium, neodymium, europium and lutetium predominate, which are relevant to high-tech industries. The report presents technological scheme of complex processing of slags of phosphoric production with obtaining of REM concentrate and precipitated silicon dioxide ("white soot"). The regime parameters of the main operations of the technology are determined: I stage- leaching of slag with nitric acid solution; extraction of the REM-containing solution with tributyl phosphate and stripping of the REM with water; settling of solution of salts of oxalic acid, calcining the precipitate to obtain a concentrate S REM oxides and II stage of leaching silicon cake to obtain "white soot". Recovery of S REM from slags of phosphoric production on various redistribution has made, %: leaching – 95.0; extraction - 90.2; extraction on the average ~ 93.2; the production of a concentrate of REM oxide is 93.9. A concentrate containing 17.3 % of REM oxides was obtained. According to X-ray analysis it contains the following phases: calcium oxide, portlandite2, gadolinium oxide and yttrium, gadolinium oxide, gadolinium oxide and cerium, neodymium oxide, neodymium oxide and cerium. Thus, the concentrate can serve as a raw material for the production of individual rare-earth metals like gadolinium, cerium, yttrium and neodymium. After performing the II stage of leaching siliceous cake with nitric acid the samples of "white soot" were obtained. Its chemical composition corresponds to the state standard and has a specific surface area equal to 180 - 200 m2/g. The technology has been tested in a large-scale laboratory scale and will solve the problem of complex processing of phosphorus raw materials and import substitution in Kazakhstan. The end-to-end recovery of S REM oxides and silicon into concentrate and product from their initial content in slags is ~ 75.0 and 98.0 %, respectively.

Jan 1, 2018

By R. ?. Sherembayeva, ?. ?. ?uktybayeva, ?. B. Rakhimbekova, N. ?. ?m?rova

"Studying the interaction of the phosphorus-containing flotation reagent with the components of the flotation system ""liquid-gas-solid"" during flotation of non-ferrous metal ores allows regulating the enrichment process. The phosphorus-containing reagent-collector anabasinium-O,O-dimethyl-thiophosphate has beensynthesized under laboratory conditions and the concentrated aqueous solution of anabasin hydrochloride and the 40% solution of sodium hydroxide have been used as the raw material. The phosphorus-containing reagent has been obtained by interaction of the anabasine base, sulfur and dimethyl phosphite, due to sulfur and nitrogen atoms it can form complex compounds with heavy metal ions.Studying flotation of copper-sulfide ore of the Sayak field with the use of the phosphorus-containing reagent-collector anabasinium has been performed in the open and closed cycles. The degree of ore grinding was 60- 62% of the class -0.074 mm. There has been established the dependence of the ore flotation parameters on: a) pH of the pulp; b) the consumption of the reagent-collector anabasinium.The effect of the pulp pH on the technological parameters of copper ore flotation has been carried out with a reagent regulator that increases the difference in the surface properties of the minerals to be separated.There has been used lime as the regulator of the medium, the consumption of which varied from 750 to 1500 g/t; the consumption of the reagent-collector anabasinium was 10, 15, 20 and 25 g/t.It has been found that when flotation of copper ore without the use of lime at pH equal to 7.8 and at the reagent consumption, g/t: anabasinium - 25, T-92 - 55, copper recovery in the concentrate is 92.72%, the quality of concentrate is 7, 1%.In flotation according to the factory mode (the consumption of xanthate is 44 g/t, T-92 is 55 g/t, pH = 7.8 (without lime)) of copper ore, copper recovery in the concentrate is 87.38%, the concentrate quality is 7, 97%, with reducing the xanthate consumption to 25 g/t copper recovery is reduced to 83.39%, the quality of the concentrate is up to 6.69%.In the experiments using the factory reagent mode in the closed cycle, with the xanthate mass consumption of 44 g/t, T-92 blowing agent of 55 g/t, the third recleaning concentrate contained 19.13% copper with recovery of 86.89%.Using a phosphorus-containing reagent instead of xanthate with the same flow rate, the third recleaning concentrate with the mass fraction of copper of 19.82% has beenobtained with recovery of 87.77%."

Jan 1, 2018

By S. Castro, L. Gutierrez

"Mining operations are often located in remote arid environments with limited access to fresh water. Shortage of fresh water in such cases makes it necessary to use seawater in mineral processing plants. Such plants treating Cu- Mo sulfide ores in seawater have been fully operational in Chile (e.g. Las Luces, Centinela). In many cases process waters used in commercial flotation plants (e.g. Mt Keith in Western Australia) are even more concentrated electrolyte solutions than seawater. This paper is an attempt at classification of the flotation operations carried out in process waters that are concentrated electrolyte solutions.INTRODUCTIONAccording to Gleick (1966), of the total Earth’ water resources 97.5% is in the oceans and ice caps, and thus only about 2.5% is fresh water. Shortage of fresh water in many parts of the world makes it necessary to use seawater in mineral processing operations. The existing commercial operations using seawater as well as recent research projects that deal not only with sulfide ores but also with apatite ores provide a lot of information that can now be generalized. The progress that has been made in this area is reviewed and based on this information an attempt is being made at classifying the flotation operations carried out in highly concentrated electrolyte process waters.SALT FLOTATIONFlotation in highly concentrated electrolyte solutions was studied by Klassen (Klassen, 1963). He reported that hydrophobic, bituminous coals, could float in salt solutions without addition of any other flotation agents. The process is referred to as salt flotation. Other inherently hyhrophobic minerals (e.g. talc, graphite, sulfur, etc.) were shown to behave similarly (Klassen and Mokrousov, 1963)As Figure 1 shows, some coals float quite well in solutions of Na2SO4, NaCl and NaNO3 (Klassen, 1963). While there are differences between the tested salts (explained by different foamabilities of these solutions) all the tests indicate that only bituminous coals float well in concentrated electrolyte solutions. 0.3 M solutions are quite sufficient to initiate a good and very fast flotation. If wettability of various coals is compared it becomes obvious that these well floating coals are very hydrophobic bituminous coals (Figure 2)."

Jan 1, 2018

By O. A. Bascur

"In recent years, metal producing companies have increased their investment in automation and technological innovation, embracing new opportunities to enable transformational change. Internet of Things (IoT) is one of many transformational initiatives, which can fundamentally revolutionize how industrial complexes operate. Whatever the issue, the answer is in the abundant and growing quantity of real time data and events collected in the grinding and flotation circuits in a mineral processing plant. Based on earlier work, today a grade recovery model permits identifying the best operating conditions in real time. We will review the strategy for increasing the value of the abundance instrumentation in current plants. An optimal Gaudin size distribution model provides augmented information from traditional sensors to find the optimal grind cut to reduce metal losses in the flotation circuits. The large amount of sensors in a flotation circuits permits to estimate the recovery and to find the optimal froth depth and aeration using an air holdup flotation model. The paper will describe the strategy of classifying data for on line generation of insights to using operational intelligence tools. We will discuss the implementation Recovery/Grind strategy with industrial examples in non-ferrous mineral processing and iron beneficiation.INTRODUCTIONThe declining supplies of high grade ores and increasing consumption of mineral and metal products have demanded higher operational efficiencies with minimum capital investments. The objective of copper flotation objectives are based on maximizing the dollars return on the concentrate produced. The economic efficiency is maximized by manipulating the circuit along the grade/recovery curve relationship. To achieve such objective improved stabilization of the grinding and flotation circuits are required (Oosthuizen, Craig, and Jamsa-Jounela, 2017)."

Jan 1, 2018

By Z. Zhang, M. -Y. Liu, X. -G. Chen, F. Breton

"The microstructures of AlSi10Mg foundry alloy in permanent mould (PM) and high pressure vacuum die (HPVD) castings were analyzed and compared. The as-cast microstructures of two castings mainly consisted of eutectic silicon particles, primary Mg2Si and Fe-rich intermetallic phases. The surface layer in HPVD castings, which has a unique feature and different structures, was carefully characterized. The dimension variation of microstructural phases along the cross section in PM samples is less than that in HPVD samples, although the size of microstructural phases in PM samples was much larger than that in HPVD samples. The mechanical properties of PM and HPVD samples were evaluated on as-cast and T6-treated conditions. The tensile properties of HPVD castings are remarkable better than those of PM castings on the as-cast condition. The T6 heat treatment greatly improves the tensile strength of PM castings while it has limited impact on the tensile strength of HPVD castings.INTRODUCTION The AlSi10Mg alloys are widely applied to the high pressure die casting (HPD) and high pressure vacuum die casting (HPVD). In the HPD process, the melt is injected into the die cavity under a high speed (30–50 m/s in the gate velocity for aluminum alloys), and solidified under a high pressure (up to 200 MPa in the cavity) and with a high cooling rate (up to ~103 Ks–1) (Gourlay, Laukli & Dahle, 2007; Ji, Wang, Watson & Fan, 2013). This results in a unique microstructure feature that is different to other casting processes under gravity. One major concern in HPD castings is porosity due to trapped air in the cavity (Ji et al., 2013), which seriously restricts the application of a heat treatment on the improvement of mechanical prosperities because of the formation of blisters on casting surfaces. For the process improvement, the high pressure vacuum die casting was developed in 1980s (Uchida, 2009). In this process, the melt is injected into the die cavity under reduced pressure (vacuum), which greatly reduces gas porosity in castings due to effectively avoiding the trapped air. Consequently, HPVD castings are heat-treatable without the formation of blisters on castings surface during heat treatment. The HPVD process has been widely applied to produce high quality structural castings in recent years attributed to reliable vacuum system development (Uchida, 2009). However, the microstructure features of HPVD castings are not systemically characterized yet."

Jan 1, 2018

By Karsten Hagenah, Tor Jensen, Jens Laugesen, Øyvind Fjukmoen, Lucy Brooks

This paper describes operational environmental threshold levels for exploitation of mineral resources in the deep sea. Such criteria are needed to be able to monitor and control deep sea mining with respect to the stringent environmental requirements that are needed. It is recommended to use existing environmental threshold levels for comparable activities where such are existing. Fields of application are mainly but not exclusively seabed mining operation activities under the governance of the International Seabed Authority (ISA). The threshold levels and limits mentioned in this paper are proposed recommendations based on other activities than seabed mining but are a proven and accepted approach in other maritime industry activities. An example of such other activities with proven and accepted environmental threshold levels are Oil & Gas exploitation activities in the sea. Background The first exploitation of mineral resources is coming closer. At the moment regulations for exploitation for mineral resources in the Area are being developed by the International Seabed Authority (ISA). The ISA regulations will contain the framework related to environmental monitoring of exploitation. However, the regulations will not contain operational environmental threshold levels for the Contractor.

Jan 1, 2018

By Kazutoshi Haga, Atsushi Shibayama, Altansukh Batnasan

The objectives of this study were to propose a viable alternative method for recovery of precious metals such as gold (Au), silver (Ag) and palladium (Pd) from waste printed circuit boards (WPCBs) and to regenerate the spent lixiviant solution for reuse. The proposed method generally consists of several steps as follows: 1). iodine-iodide leaching for metals extraction; 2). separation and recovery of precious metals and metal impurities from a pregnant leach solution; 3). regeneration of the spent iodine-iodide solution/lixiviant. In this method, more than 99% of Au leaching was achieved in the iodine-iodide solution from the solid residue of WPCBs that was obtained via sequential processes including incineration at 800 ?C and high pressure oxidative leaching with a diluted sulfuric acid at 120 ?C, while the leaching of Ag and Pd was less than 1%, respectively. Besides Ca, Cu, Ni, Co and Zn as main metal impurities, leaching efficiency of other metals did not exceed 1%. The precious metals and base metals as metal impurities present in the pregnant leach solution were separated and recovered by precipitation using L-AA and NaOH solutions. About 99.8% Au, 81.7% Ag and 72.8% Pd were recovered from the pregnant solution at pH of 2 with the addition of 0.1 M L-AA as precipitating agent. The remained small amounts of precious metals and metal impurities were precipitated at pH 13 using 1 M NaOH. The spent lixiviant after sequential precipitation was regenerated in the presence of hydrogen peroxide, hydrochloric acid and potassium iodide. It was revealed that over 90% of gold could be extracted from the residue of WPCBs with the regenerated lixiviant solution.

Jan 1, 2018

By Xianjun Lyu, Junxiang Wang, Peng Wu, Minjie Lian

"In recent years, the efficient cementation of mine tailings is a new way to manage mine solid wastes. The traditional cement materials have a slow setting time, large dosage and poor cementation strength for fine aggregate such as mine tailings. Therefore, the preparation of new type cementitious materials for the cementation of fine tailings has great potential in the treatment of mine waste solids. The paper mainly focuses on exploring the critical factors affecting the cementing performance of granulated blast furnace slag and its performance in the cementation of fine aggregate. Results indicate that the fineness of slag has a significant effect on its cementitious activity and Portland cement clinker has a better stimulation effect on the cementitious properties of slag than lime. And, anhydrite has a better early stimulation effect on the cementitious properties of alkali-activated slag compared to semi-hydrated gypsum and dihydrate gypsum. According to a series of tests on the cementation of fine iron tailings, the optimal ratio of slag, Portland cement clinker and anhydrite is determined as 60:30:10. Compared with P.O 42.5 ordinary Portland cement, the new slag based cementitious material shows much better cementing performance on fine tailings sample. Under the dosage of 12%, the compressive strength of fine tailings mortar using slag-based cementitious material in 3 curing days is increased to 168% that of using P.O 42.5 ordinary Portland cement, while the compressive strength in 28 days curing period is increased to 194%."

Jan 1, 2018

By J. L. Brinkman

"One of the most common emissions from detonating explosives are nitrogen oxides (NOx), which are potentially deadly if inhaled. Lab studies estimate emission quantities, though great variation is shown based on site-specific conditions, and lab tests may not fully represent field results. Field VALUES (have not been measured due to the vast area affected. OSMRE recently promised to release a ruling regarding surface mine NOx production. Once the ruling is implemented, it may eventually be necessary to monitor site-specific NOx production from blasting. A small unmanned aerial vehicle system (sUAS) is able to carry a NOx gas monitor, rapidly travel to the blast location, and to follow resulting clouds of dust and emission gasses. This project will perform laboratory tests to expand on current estimations, determine an optimal method for collecting data, and evaluate the ability for this unique application of sUAS to assist in health risk assessment for mine employees and nearby communities. Additionally, large initial NOx concentrations do not necessarily correlate to unsafe conditions, and this project will be ground breaking in observance of surface blasting emission dispersion. The project is still in early phases at the time of submission for this paper (Nov 1, 2017). Therefore, this paper focuses primarily on summarizing background research related to the project and a description of the project plan. INTRODUCTION Nitrogen oxide gases (NOx) are common emission by products of surface mine blasting. These gases can potentially cause risk to human health and safety, both for mine workers and communities near the blast site. However, these emission quantities are largely unmeasured and no attempts have been made to relate these VALUES (to human health risk. The primary objectives of this project are to determine actual quantities of emission gases produced during surface blasting, to evaluate immediate and long-term risks to nearby people, communities, and ecosystems, to develop a system for mine employees to easily monitor emission and risk levels, and then provide guidelines for mitigating health risks based on a location’s emission results. BACKGROUND Current research regarding health risk produced by surface mine blasting NOx emissions is extremely lacking. Estimations have been made based on laboratory research, though these same test results show wide ranges of possible gas quantities produced based on site-specific conditions. Even if these estimations are accurate, no method has been created to relate gas quantity produced to human exposure concentrations. To further understand this field, background research was studied pertaining to blasting emission gas formation, laboratory and field measurements, harmful effects of blasting emission gases, and relevant government regulations. Background on Blasting Emission Gases"

Jan 1, 2018

By N. Damiano, J. Noll, C. Zhou, J. DuCarme

"Preventing machine-related injuries is one of the major safety concerns in underground coal mines. Severe injuries and fatalities occur when a miner is struck, crushed, or pinned by mining equipment such as a continuous mining machine (CMM), shuttle car, or a scoop. Proximity detection systems (PDSs) have been applied in mining to reduce these types of injuries and fatalities. All of the PDSs that are currently approved by the Mine Safety and Health Administration (MSHA) for use in underground coal mines are magnetic-field based and could be affected by metallic objects such as trailing cables. Researchers from the National Institute for Occupational Safety and Health (NIOSH) investigated the influence of trailing cables on the performance of PDSs. In particular, the magnetic field coupled from proximity system generators to a de-energized trailing cable were characterized. The results show that significant energy can be coupled from the proximity system generators to a trailing cable when there is a closed loop in the cable. The effect on PDS performance from the magnetic field radiated around an energized trailing cable was also quantified for different current amplitudes in the cable. It is shown that the magnetic field caused by the electric current in the trailing cable mainly consists of a 60-Hz signal and its harmonics which cause little interference to the PDS. The results presented in this paper can help PDS manufacturers to design better systems that are more immune to these effects. INTRODUCTION An average of 250 injuries occur every year during operation of Continuous mining machines (CMMs), and 43 miners have been killed by striking or pinning accidents involving CMMs in the U.S. from 1984 to 2015 (Mine Safety and Health Administration, 2015). In addition, there have been 10 fatal accidents involving mobile haulage equipped with trailing cables from 2000 to 2015 (Noll et al., 2017). In response to these fatalities and injuries the Mine Safety and Health Administration (MSHA) promulgated a regulation in 2015 requiring the use of a proximity detection system (PDS) on all CMMs except full-face machines and proposed a regulation in 2016 which would require a PDS on other mobile underground equipment. Current PDSs approved for underground use are magnetic-field based. The PDS contains machine-mounted magnetic field generators that create fields around the machine. The other part of the PDS is a miner-wearable component (MWC) that reads the flux density of the generators. These systems use the magnetic field strength readings from the MWC to determine whether a miner is at a safe distance from the machine. A stable magnetic field is essential for the accuracy of the system."

Jan 1, 2018

By Li Tianxia, Zhou Jing, Zhu Yimin

"A typical low-grade of high sulfur bauxite fr contains 54.71% Al2O3, 11.35% SiO2 while the ratio of aluminum and silicon was 4.25, and harmful components such as Fe and S graded 7.3% and 1.33% respectively. The ore is characterized by complex mineral compositions, fine dissemination of particle size of pyrite and diaspore, low desulfurization efficiency, and difficult separation of aluminum and silicon. In order to improve the degree of concentration, recovery and desulfurization efficiency on the basis of process mineralogy studies, the floatation behavior of high sulfur bauxite in the process of desulfurization and desilication were studied through laboratory tests and pilot plant tests. KEYWORDS high-sulfur bauxite; low grade; flotation; desulfurization;desilicication INTRODUCTION In order to solve the selection problem of bauxite mine area, we carried out technological mineralogy, laboratory test, small-expansion Dalian test to solve the problem of the refractory ore. Main research contents and conclusions were presented as followings :(1)Process mineralogy research shows: the main mineral components include diaspore, kaolinite, chlorite, pyrite, limonite. (2)Batch flotation tests indicated that slime can be dispersed well during desulfurization floatation when Na2CO3 was used as modifying agent. (3)Poilot plant tests shows that Batch flotation tests results are correct. 2?PROCESS MINERALOGY 2.1 Chemical Composition of Ore 2.1.1 Spectral Analysis of Sample The results of the semi-quantitative analysis of X-Ray -fluorescence spectra of the original ore are shown in Table 2-1. The results of spectral analysis show that the main components of the sample are O, Al, Si, followed by Fe, Mg, Ti, S and so on, while the content of other elements is very small. The value is Al, and maybe Ti, for bauxite, while Fe and S are unfavorable elements, and Si and Mg and Ca are the main impurity elements."

Jan 1, 2018

By Mingfei He, Xianyang Qiu, Hongling Wang, Yude Gao, Qingbo Meng, Xiaoping Xu, Hao Bu, Guosheng Wang

"By the “HGMS-gravity separation-Flotation” combined technology, a Ta-Nb-Sn concentrates with the grades of Ta2O5 10.00%, Nb2O5 9.13% and Sn 42.62% at the recovery of 44.73% , 9.13% and 14.62% respectively , a Li concentrate with Li2O 3.11% at the recovery of 51.83% and a feldspar product are obtained. All the value elements are recovered. INTRODUCTION Tantalum and niobium widely used in electronics, atomic energy, aerospace and chemical industries with the advantages of high melting point, good ductility, low vapor pressure, strong corrosion resistance and high thermal conductivity are important strategic resources which occupy a special position in rare metals (Crockettand, 1993; GAO and Zou, 2004; LI and HUANG, 2012). China's tantalum and niobium resources are poor, and most of them are low grade, fine grain size, complex composition, and polymetallic associated with refractory mineral resources (GAO and Qiu,2013; Liang and Li, 2016). The Yifeng Lion Ore containing lithium and other rare metals (tantalum, niobium and tin) is an important lithium polymetallic deposit in China Jangxi province. While extensive previous studies have settled on the recovery of lithium minerals by flotation only for the extremely low grade of Ta, Nb and Sn. The regular gravity concentration is used, and the recovery of tantalum niobium is low. This paper sets out to investigate a combined flowsheet of “high gradient magnetic separation (HGMS),-gravity separation-flotation” to effectively comprehensively recover the Li, Ta, Nb, Sn and the feldspar resources in the Yifeng Lion Ore.ORE PROPERTIES Chemical analysis The run of mine comes from Jiangxi Yifeng Lion ore. The main elements of the ore chemical analysis results shows in Table 1. From Table 1, the grades of lithium and rubidium are relatively high, but the grades of tantalum and niobium are lower than the industrial grade; feldspar with high content of potassium and sodium and low content of iron can be used as high-quality ceramic raw materials."

Jan 1, 2018

By R. ?. Shishmarjov, Yu. ?. Davidenko, S. V. Bukhalov, ?. S. Baksheev, M. S. Shkirya, N. ?. Aikasheva, D. V. Bogdanovich, ?. Yu. Faustova

"The goal of prospecting operations in the Republic of Altay was to locate gold-sulfide-quartz mineralization. For this purpose we applied the technology of electromagnetic sounding and induced polarization (EMS-IP). These operations resulted in localizing promising sites with presence of sulfidization. The EMS-IP method proved to be highly efficient amongst other prospecting methods targeted at recognizing zones of sulfide mineralization making up 91%, considering that in more than half cases the ore intervals were the case. In the Yakutian diamondiferous province the EMS-IP technology was approbated during three field seasons to accomplish the assignments on searching for kimberlite bodies under conditions of various geological types. As a result, the reference objects were distinguished, and geoelectric parameters of kimberlite pipes of explosion were defined.INTRODUCTION In the time span 2015-2016 in Gorny Altay the EMS-IP technology was approbated in the Novokuznetsk area. The on-land areal geophysical survey was performed by EMS-IP method applied to identify, outline and locate promising sites with Au-Ag-bearing polymetallic mineralization within surveyed areas. Compared to the hosting rocks, the sulfides contained in polymetallic mineralization are typified by low specific electrical resistivity (SER) and high polarization. The areal survey conducted via EMS-IP method provided spatial characteristics of searched object. From July 2016 to August 2017 our expedition group carried out serial test works and laboratory investigations intending to define performance capabilities of EMS-IP technology in searching for kimberlite bodies under conditions of diverse geological types. The prerequisites for serial work were operations accomplished at the «Listvenichny» site lying 35 km away from Mirny town in the Sakha Republic (Yakutia), where the EMS-IP technology was probed for locating position and measuring geoelectric parameters of tuff pipe «Buardakhsky». After successful completion of operations it was decided to evaluate geoelectric parameters of kimberlite pipes of explosion."

Jan 1, 2018

By Gökçe Törenli, Okay Tutar

"Predicting the performance of plant-scale comminution circuits is essential to monitor the energy use and product size distribution, allowing us to control and optimize the whole process. In the light of this issue, with the assist of recent technologies, simulation techniques utilize the chance of putting the theory into practice in the most accurate way. For this purpose, this study aims to evaluate and optimize the efficiency of a plant-scale ball mill circuit by using perfect-mixing ball mill model on a simulation environment. The comminution circuit is selected from a specific copper-ore processing plant in Turkey. The essential parameters which are required for this study such as fresh feed Bond work index, size distribution etc. are determined by laboratory experiments. The forecasted data which are calculated by third-party software will be compared by the industrial operating data, in order to determine the performance of comminution circuit. In addition to that, this methodology provides a greater ability to analyse, optimize and understand the comminution circuit of ore treatment plant. The authors believe this work will provide supplementary data for further studies on simulation and subsequent optimization of comminution circuits.INTRODUCTION By the assist of mathematical models of the grinding mills and classifiers, simulation of the grinding circuits become more common in comminution because it is relatively economical and able to consider many variables simultaneously. It’s proceeds depends on the accuracy of the models and capability of reflect real operations. Computer-based simulation studies would provide the quantified information about the effects of the proposed changes on the comminution circuit performance in terms of size distribution, mass flow rates, equipment efficiency etc. Then the mentioned data used in order to check the suitability of the current equipment to the modified conditions, and for equipment selection. The outputs of circuit could also be used to estimate downstream flotation circuit performance because the general aim in this study is to The aim of the study is to investigate optimum operating variables and achieve p(80) size of 57 µm and 64 % of -36 µm particle in hydrocyclone overflow stream, which is optimum for that porphyritic copper ore for best concentrate recovery after flotation process in specific copper ore comminution circuit by using modelling and simulation techniques. Sampling survey was carried on the fine ore bin in order to perform Bond work index test and determine work index value (Wi). Thereafter mass balancing, using the size distribution data and tonnages, models for ball mills and hydrocyclone were developed. Finally, the circuit performance were investigated by computer simulations via JKSimMet software."

Jan 1, 2018

By J. F. Burr, D. P. Snyder, G. W. Luxbacher

"The Mine Improvement and New Emergency Response Act (MINER Act) of 2006 established the Office of Mine Safety and Health (OMSH) within NIOSH and provided authority for awarding contracts related to the development and implementation of new mine technology and equipment. Subsequently, Congress provided additional funding to NIOSH to initiate and continue the program. OMSHR has fulfilled this Congressional mandate through annual Broad Agency Announcement (BAA) solicitations, directed Requests for Proposals (RFP) and Inter-Agency Agreements (IAA), and has further expanded the program through capacity building BAA contracts with U.S. university mining departments in the areas of mine ventilation and ground control. This paper describes the extramural funding program and broadly examines the results of the 150+ contracts issued to date, grouped into key focus areas. INTRODUCTION The Mine Improvement and New Emergency Response Act (MINER Act) of 20061 established the Office of Mine Safety and Health Research (functioning as the Office of Mine Safety and Health Research or OMSHR) within the National Institute for Occupational Safety and Health (NIOSH), and provided authority for awarding contracts related to the development and implementation of new mine technology and equipment. The OMSHR external contracts program was formed in accordance with the MINER Act and has since issued over 150 contracts focused on worker health and safety. Initial funding for this program was provided by Congress through two Emergency Supplemental Appropriations (ESA) and was focused on emergency oxygen supply, communications and tracking, and refuge chambers (also referred to as refuge alternatives). Since the MINER Act, Congress has continued to fund the program through the annual NIOSH mining appropriation. The program was supplemented starting in 2009 with an academic capacity building program directed toward developing university tenure-track faculty and facilities and supporting graduate students in the area of mine ventilation; ground control was added as an additional focus area in 2011. A short synopsis of each contract is published on the NIOSH Mining website2 and final reports are available in digital form on request. A summary of the progress OMSHR has made over the 10-year period since the Act was published previously.3"

Jan 1, 2018

By M. Dadvand, G. Kipuros, A. Dadvand

"The ability to codeposit fillers within a nickel matrix has led to the production of a new generation of cermet coatings with properties useful for various applications. Hexagonal boron nitride (hBN) is a ceramic-type particulate matter with thermal conductivity, thermal stability, inertness, and lubricity properties that allow it to be codeposited. In this paper, a method was developed for modifying hBN surfaces to allow them to be uniformly dispersed in water-based solutions such as an electroless nickel plating bath. hBN surface modification improved wear performance of the electroless plated cermet due to enhanced interaction between the particulate and nickel matrix. RÉSUMÉ La capacité à effectuer un dépôt simultané de charges dans une matrice nickel a abouti à la production d’une nouvelle génération de revêtements cermet (une combinaison de céramique et de métal) dotés de propriétés très utiles pour diverses applications. Le nitrure de bore hexagonal (h-BN) est une matière particulaire de type céramique utilisée pour ses excellentes conductivité et stabilité thermiques, son inertie ainsi que son caractère lubrifiant, qui permettent son dépôt simultané. Cet article explore une méthode mise au point pour modifier les surfaces du h-BN de manière à ce qu’elles se répandent uniformément dans des solutions aqueuses telles qu’un bain de dépôt autocatalytique de nickel. La modification des surfaces du h-BN a amélioré la résistance à l’usure du placage autocatalytique du cermet en raison d’une interaction accrue entre la matière particulaire et la matrice nickel.INTRODUCTION Electroless nickel alloy coatings can be used for many applications; however, the need for improved tribological properties such as higher wear resistance and better lubricity has increased interest in incorporating particulates (fillers) into the nickel matrix by codepositing the particulates with nickel during the plating process. The selection of the particulate type depends on the desired properties (Sahoo & Das, 2011; Sudagar, Lian, & Sha, 2013). In terms of tribological applications, electroless nickel-based composites are categorized mainly into lubricating and wear-resistant composite coatings depending on the type of particles incorporated. The electroless nickel-phosphorus (Ni-P) composite coatings are composed of codeposited solid lubricants such as polytetrafluoroethylene (PTFE), graphite, WS2, MoS2, and hexagonal boron nitride (hBN) and, compared to nanocomposite electroless Ni-P coatings, they demonstrate a lower coefficient of friction. On the other hand, the nickel-phosphorus wear-resistant composite coatings are composed of hard particles such as silicon carbide (SiC), aluminum oxide (Al2O3), boron carbide (B4C), silicon nitride (Si3N4), diamond, tungsten carbide (WC), and zirconium oxide (ZrO2) and, compared to nanocomposite electroless Ni-P coatings, they have higher hardness and better wear resistance (Sahoo & Das, 2011; Sudagar et al., 2013; Parucker, Klein, Binder, Ristow, & Binder, 2014; Chakarova, Georgieva, Petrova, Dobreva, & Stoychev, 2016)."

Jan 1, 2018

By Y. G. Zhu, G. B. Zheng, Z. B. Qian, X. R. Zhang, A. J. Ren

"Based on PMA polymer, two kinds of novel macromolecular depressants, PMTA and PMA-PDTC, were designed and synthesized. PMTA was used for desilication in hematite reverse flotation. PMA-PDTC was used in the separation of Cu-Pb concentrate as galena depressant. The micro-flotation results showed that PMTA exhibited a good depression performance compared to starch. We found that 98.29% of hematite was depressed with a grade of 65.24% at pH 11 with 12 mg/L dosage. The flotation separation results of Cu-Pb concentrate demonstrated that PMA-PDTC was an effective depressant for galena in separating galena from chalcopyrite. When IPETC was used as collector, at pH 8.5, the flotation separation tests demonstrated that Cu concentrate was obtained with a grade of 28.89% containing 12.12% Pb.INTRODUCTIONThe role of depressants is crucial in the separation of oxide or sulfide minerals, for example, the desilication in hematite concentrate and the separation of Cu-Pb concentrate.It is well known that, in current reverse flotation processing of hematite, starch is a traditional depressant for hematite. Most research focus on the modification of starch [1-3]. Although its depressing ability is enhanced in some extent, its own shortcomings is still existed. So, it is important to develop a new hematite depressant instead of starch.In the separation of chalcopyrite and galena, because of their extremely similar floatability, it is difficult to realize the separation of these two minerals. Traditionally, there are two methods widely used in the separation of Cu-Pb concentrate by depressing chalcopyrite with cyanide [4] or depressing galena with dichromate [5] in most cases. However, these two inorganic depressants are toxic and hazardous. Their use could cause heavy pollution problems and a large loss of precious metals. In order to adapt to the requirements of sustainable economic development and environmental protection, the research and development of green and environmental depressant has gained more and more significance."

Jan 1, 2018

By V. A. Vorob'ev, A. N. Larionov, E. N. Ivanov, M. A. Ryazanov

The aim of the research is to increase the recoverable value of poor, difficult-to-digest complex mineral raw materials. In the Republic Belarus, universal centrifugal-shock devices have been created for crushing, grinding and classification of ore and non-metallic mineral raw materials in dry mode, which differ from foreign analogues by a higher level of resource saving (including electricity and materials). Dry-ore preparation technologies have been tested on a pilot scale: fine crushing (replacing grinding in rod mills), grinding (replacing wet grinding in ball mills) and pneumoclassification on different types of ores, - which made it possible to identify the criteria for the suitability and unsuitability of mineral raw materials for their use. The possibility of regulating the upper and lower limit of the size of the finished material is established, the possibility of reducing the yield of slimes (-0,020 mm) to 5 times is determined. A comparative analysis of the contrast degree of separation characteristics of ore a similar granulometric composition, crushed in wet and dry conditions, is performed. The achieved contrast degree of gravity properties after dry grinding - 104,3; after the wet - 60.2. When enriching on a centrifugal concentrator, gold recovery to the concentrate after dry grinding increased by 13.12% while improving the quality of the concentrate from 78.3 g/t gold to 90.75 g/t. When testing the gravity-flotation scheme for the enrichment of poor gold-quartz ore, the increment of gold extraction after dry grinding was 7.6% for gravity and 9.5% for flotation; the total increase in extraction is 17.1%. The possibility of flotation of a larger material after dry grinding has been proved, with an extraction gain of 1.5% compared to the flotation of thinner material after ball milling. The influence of dry technology on the efficiency of the leaching of gold and silver (an extraction gain of 5.5 to 10%) and heap leaching (extraction gain - up to 18.3%) was studied. The positive influence of dry ore preparation technologies on the efficiency of gold and silver heap leaching and heap leaching, thickening and filtration is proved. Lines of dry ore preparation technologies can be used in modular complexes for processing technogenic raw materials.

Jan 1, 2018