Search Documents

By J. Kim, H. Cho

The objective of the experiment was to investigate the efficiency of hindered-settling column in recovering carbon from anthracite. Two types of Korean anthracites were prepared for feed materials. Each sample was crushed and classified by size, and washability analyses were performed. Separation efficiency was evaluated under various operating conditions using a laboratory scale hindered settling column. Results showed that the carbon recovery was higher for the smaller sizes, but the purity of the product was better for the larger sizes. In, overall, 2-0.21mm particles of 40-45 % ash could be processed into about 20 % ash products.

Jan 1, 2002

By Harvey W. Parker

The underground industry is challenged by many complex technical and non-technical issues and risks. The most obvious of these are the traditional technical issues that we usually try to address with risk management techniques. However, there are many other non-technical risks that our projects face on a daily basis which we often fail to fully recognize or appreciate. This paper addresses some of the less-technical broad-based risks in order to put them into perspective with the technical risks we face day to day in underground planning, design and construction. The good news is that Risk Management techniques are not always about bad things. For obvious reasons Risk Management is always thought of in terms of the ?downside? of risk (i.e., the identification and mitigation of things that can go wrong). On the contrary, there is an ?upside? of things that might go better than expected. Fortunately, if a deliberate effort is made, the same principles and techniques that our industry uses in Risk Management can be applied toward identifying and quantifying the Opportunities and Benefits that might occur. In this way, the process of conducting risk management programs can not only identify the downside risk but can be used to identify and direct projects to take advantage of the upside of uncertainty (i.e., Opportunities as they arise). This beneficial aspect of risk management programs will be highlighted in this paper together with the importance of the non-technical issues.

Jan 1, 2008

By Peter Bigwood

Whether drilling through tough clay or breaking rock, or facing the most severe conditions including mixed face ground, perched water and running and flowing sands, working under-ground certainly comes with no shortage of challenges. In an environment where the unknown is faced on a daily basis, tunneling contractors must be able to rely on their equipment to get the job done properly. Not only that, their equipment must comply with two of the highest priorities: safety and efficiency. In addition to being the number one concern, a proven safety record provides additional benefits to a company. A safe work environment serves as a key component to company growth, including the ability to remain competitive in bidding and maintaining higher-level, more challenging projects.

Jan 1, 2012

By D. P. Richards

Tunneling in carbonate sedimentary rocks such as lime stones and dolomites can be difficult when solution channels or voids are anticipated. Addressing the risk aspects associated with these formations can be done effectively through the Geotechnical Baseline Report (GBR) by properly characterizing the ground and ensuring that the Owner?s and the Contractor?s interests are represented and protected. This paper presents a review of tunneling difficulties in these rocks and includes a review of site investigations, geologic characterization, and presentation in the GBR. Key construction issues are also discussed, including appropriate excavation technology, mechanisms of face support and groundwater control, and quantifying grout takes.

The ventilation conditions at the underground coal mines are influenced; first: by the disturbances of the natural nature (barometric pressure, methane liberation, etc.), and second: by the disturbances caused by the production process. The major goal of this study was to determine the changes of the ventilation parameters, such as the flow, pressure and methane concentration around the longwall panel, particularly, along the longwall face due to the shearer operation (motion). It is well known from the practice, that the movement of the shearer influences the ventilation parameters around the longwall panel, including the gob area. Until now, these data were gathered in a single or multiple locations at the different time. However, only the simultaneous measurements of all of these values allow seeing the time dependent interrelationships between measured parameters. To be able to show these interrelationships, special experiments, described in this paper, were carried out by the author. These experiments were prepared and executed at the BUDRYK Coal Mine in Poland. During each experiment a simultaneous measurements and monitoring of the barometric pressure, air velocity and methane concentration at the different locations along the longwall face, were performed. The investigation was possible by using a special setup of instruments with a short sampling time, i.e., within 2 seconds. The monitoring of the absolute pressure was conducted by using the digital barometer µBar, developed by EMAG, based on the SETRA pressure transducer, model 470. The velocity of air was measured using the electronic vane-anemometers, developed by IMG-PAN. The methane concentrations were measured using methanometers as the part of the EMAG automatic gas monitoring system. The investigation data confirmed that disturbances due to the operation (motion) of the shearer at the longwall face have a local character. It could be also seen that a large diameter shearer (compared to the total cross-section area available for the air flow) is acting as the piston compressing the air (the overpressure) ahead of the shearer. This fact affects the methane mixing process and flow patterns in the vicinity.

Jan 1, 2009

By R. Karl Zipf

Highwall mining is an important surface coal mining method, and it may account for approximately 4% of total U.S. coal production. Highwall stability is the major ground control related safety concern. Ground control plans for highwall mining should specify hole width, web pillar width, barrier pillar width and number of holes between barriers. This paper offers simple design charts for these parameters aimed at providing “ball park” checks. Web pillars containing pre-existing auger holes are analyzed and a design chart for estimating their minimum width is also presented. Finally, close proximity multiple seam highwall mining, which may have caused several serious highwall failures, is analyzed. Web and barrier pillar recommendations for this special situation are presented.

Jan 1, 2005

By Christian Maguire

The presence of hydrogen sulphide in sewerage systems leads to severe concrete corrosion. Acid causes breakdown of the concrete matrix, and attacks reinforcement. Older sewer systems under acid attack are often found to be acutely corroded, sometimes after short operational periods. Consequently secondary liners are now almost always used. Polymer concrete is extremely acid resistant and if used in segmental linings can forgo the need for a secondary lining. Combined with fibers and/or GFRP rebar Polymer Concrete can produce a very strong acid resistant lining, saving considerable time in the installation of additional liners. This paper explains the problems and advantages of using Polymer concrete in segmentaly lined wastewater tunnels, addressing areas of design, cost, and programming.

Jan 1, 2008

A series of gas inrush events occurred during development at Grosvenor mine resulting in exposure to elevated levels of methane at the production face. A total of 22 gas inrush events occurred releasing between 15 and 130 m3 of methane during each event. The presence of an undrained seam in the immediate floor, geotechnical characteristics of the floor, and the stress environment all contributed to these dynamic floor events, while the geological characteristics of the seam below, such as the seam thickness and ash content of 75%, prevented effective pre-drainage. However, events only occurred in headings mined parallel to the principal horizontal stress direction. In cut-throughs (C/Ts) perpendicular to the principal stress direction, no events occurred, and higher methane levels were observed at the production face.

Jan 7, 2020

By C. O. Lee

The Grand Isle Sulphur Mine is located in the Gulf of Mexico, approximately seven miles off the coast of Grand Isle, Jefferson Parish, Louisiana. The depth of water at this location is about 50 feet. The deposit is on acreage covered by oil, gas, and mineral leases which were originally issued in favor of Humble Oil & Refining Company by the State of Louisiana, and which were continued, maintained, and redesignated by the Department of the Interior of the United States, pursuant to Section 6(b) of the Outer Continental Shelf Lands Act. On September 19, 1956, Freeport Sulphur Company acquired from Humble Oil & Refining Company the sulphur rights underlying the tracts. This assignment was approved by the Secretary of the Interior on July 12, 1957. The Director, United States Geological Survey, approved Freeport Sulphur Company as Operator on July 31, 1957. Actual design began in September 1956; the first structural contract was let December 15, 1957, and offshore erection began in June 1958. The initial phase of construction will be completed and production started in early 1960. The estimated total cost of the project is $30,- 000,000, of which $8,000,000 is the extra cost for being in the Gulf of Mexico.

Jan 1, 1959

By T. Patten

A method for stabilizing mercury containing waste for landfill disposal would be a very cost effective solution for industry. A mercury polythiocarbonate material which is made via a metallurgical process passes a traditional TCLP for mercury. The mercury polythiocarbonate material was subjected to a more thorough evaluation, the Integrated Leaching procedures as described in Kossan (1) and Sanchez (2)The procedure involves leaching the mercury polythiocarbonate material at varying pH and sample size to liquid. The procedure had to be adapted for small sample sizes and finely divided materials due to the product characteristics and available material. The leachates were evaluated and found to be stable within common environmental pH values. The performance details on how Inter-Mountain Labs met the leaching requirements of the procedures and the analysis of mercury are presented.

Jan 1, 2012

By S. Frimpong

The cable shovel excavator is used for primary production in many surface mining operations. A major problem in shovel excavation is the variability of material diggability, resulting in varying mechanical energy input and stress loading of shovel dipper-and-tooth assembly across the working bench. This variability has a huge impact on the shovel dipper and tooth assembly in hard formations. In addition, the geometrical constraints within the working environment impose production limitations resulting in low production efficiency and high operating costs. A potential solution to the above problems is the application of an intelligent cable shovel excavation(ICSE) technology. In this paper, dynamic models of the cable shovel excavator are developed with numerical examples. These models form the basis for developing dynamic shovel simulators for an intelligent shovel excavation technology. The dynamic equations are developed using the Newton-Euler techniques. The path trajectories for efficient excavation, dynamic velocity and acceleration profiles, and dimensioned parameters for optimum feed force, torques and momentum of shovel boom-bucket assembly are modeled and used for efficient excavation. The optimum digging forces and resistances for the cable shovel excavator are modeled and used to predict optimum excavation performance.

Jan 1, 2003

By R. Grandori, L. Pellegrini

The construction of the La Joya hydropower plant (Costa Rica) was awarded by the Spanish power company, Union Fenosa, to the Italian Joint Venture formed by the companies SELI SpA and Ghella SpA. The project, located in a mountainous region of central Costa Rica, includes a 7.9-km-long head race tunnel having an excavation diameter of 6.18 m. A double-shielded TBM was selected to perform the tunnel excavation, which involved mainly volcanic rocks in variable but generally very weak conditions. The tunnel crossed long and continuous sections in completely weathered rock masses with no residual cohesion and with high water inflows. The paper describes and analyzes: The special methods adopted to overcome these sections with the TBM includ-ing face stabilization by chemical grout and foams as well small by-pass tunnels in the crown combined with TBM advance/support The grouting design and the grouting method that was implemented to meet the waterproof design specifications and restore the original groundwater level in the mountain The additional geological investigations performed to improve the knowledge of the rock mass in front of the TBM and the outcomes of these investigations The performance of the TBM in different ground conditions and on average along the entire tunnel Finally, the author’s comment about the possibility of implementing and improving the technologies experimented with in this project in future similar applications.

Jan 1, 2007

By H. K. Lin

Deepwater discharges of sulfide flotation tailings have been practiced for several decades. Oxygen penetration and organic matter content in such environments are the two major factors that determine their reduction-oxidation condition and hence the rate of sulfide mineral dissolution under such discharge environments. In this study, the effects of solution redox potential and pH on the dissolution of some heavy metals from sulfide flotation tailings were examined. Zn, Pb and Cu concentrations in solution were all higher at a higher redox potential and lower pH. Dissolved Zn concentrations reached 100 ppm even at a low redox potential of 105 mV and near neutral pH after 33 days. Pb concentrations were below 2 ppm at 105 mV and near neutral pH after 165 days. At 105 mV, the Cu concentrations were below 0.2 ppm at near neutral pH after 165 days. At pH 2.3, the Fe concentrations were higher at 420 mV than at 105 mV. But at pH 6.8, the Fe concentrations were lower at 420 mV than at 105 mV, due to the oxidation of Fe2+ to Fe3+ and the subsequent precipitation of ferric hydroxide. Arsenic concentrations in solution were all less than 0.002 ppm. For Zn, Cu and Fe, no significant differences were observed between the tests in solutions prepared using seawater and those using distilled water. However, Pb concentrations reached higher levels in solutions prepared using seawater.

Jan 1, 2009

By N. Damiano, C. Zhou, B. Whisner, M. Reyes

"The industrial Internet of Things (IIoT)—a concept that combines sensor networks and control systems—has been employed in several industries to improve productivity and safety. NIOSH researchers are investigating IIoT applications to identify challenges of and potential solutions for transferability of IIoT from other industries to the mining industry. Specifically, NIOSH has reviewed existing sensors and communications network systems used in U.S. underground coal mines to determine whether they are capable of supporting IIoT systems. The results show that about 40% of the installed post-accident communication systems as of 2014 require minimal or no modification to support IIoT applications. NIOSH researchers also developed an IIoT monitoring and control prototype system based on low-cost microcontroller Wi-Fi boards, to detect a door opening on a refuge alternative, activate fans located inside the Pittsburgh Experimental Mine, and actuate an alarm beacon on the surface. The results of this feasibility study can be used to explore IIoT applications in underground coal mines based on existing communications and tracking infrastructure. INTRODUCTION The nation’s approach to health and safety in mining has historically been reactive in the sense that health and safety regulations and mandates have traditionally been passed as a result of tragic mining accidents. An example of this is the Mine Improvement and New Emergency Response Act (MINER Act) of 2006, which was passed as a result of several mining accidents where tracking of and communications with underground personnel were severely limited. While this reactive approach has led to the development and implementation of highly impactful safety interventions and safety practices, there currently exists a technological revolution that can shift the paradigm toward a proactive approach based on preventative methods: Internet of Things (IoT). IoT is the network of physical objects or ""things"" embedded with electronics, software, sensors, and connectivity to enable that network to achieve greater value and service by exchanging data with the manufacturer, operator, and/or other connected devices [1, 2]. It should be noted that IoT has been defined from various perspectives, and hence numerous definitions exist in the literature. The apparent ambiguity of the IoT definition might be due to the fact that IoT is syntactically composed of two terms: internet and things. The first one pushes towards a network-oriented vision, while the second tends to put the focus on generic objects. The traditional internet can be viewed as an internet of computers —i.e., “things” connected to the internet are computers only. IoT “extends” the internet by allowing other generic things that are commonly found in our daily life, such as refrigerators and cars, to be interconnected via the internet, and thus creates a bridge between the virtual word and the physical world."

Jan 1, 2017

By Kristen E. Coose

Concrete is a mixture of a fine aggregate (sand), a coarse aggregate (gravel), cement, and water. Cement itself is the most expensive of the ingredients but generally amounts to only about 10% of the concrete mixture. Cement raw materials include calcium, alumina, iron oxide, silica, and gypsum. They are heated and chemically changed into clinker "minerals," which are then ground and shipped as cement. Each of the four main clinker minerals-tricalcium silicate, dicalcium silicate, tricalcium aluminate, and tetracalcium aluminoferrite-impart specific strength and compositional properties to the final concrete product. During hydration of the cement, chemical changes produce new minerals that include calcium silicate hydrate gel (C-S-H, the main constituent of hydrated cement paste), calcium hydroxide, and calcium, sodium, potassium, and sulfate ions, among others. Two main reactions can occur that may be deleterious to concrete. Normal cement pore solutions, in a hydrated cement, contain sodium hydroxide and potassium hydroxide. If these alkali concentrations are too high, they can react with the siliceous aggregate (alkali-silica reaction, or ASR) to form an alkali-rich calcium silicate hydrate gel (C-N+K-S-H), which, upon prolonged contact with water, can expand to crack the concrete. The other deleterious reaction occurs when the mineral ettringite (Ca6A12(S04)3OH12. 26H20) forms after the concrete is hardened (delayed ettringite formation) and cracks the concrete. Many of the concrete bridges and structures built in New Mexico in the past 20 years are in need of replacement due to deterioration. Many others constructed very early on in the century are still sound. By collecting and analyzing samples of both old and new concrete and good and bad concrete, we compared their differences on both a microscopic and macroscopic scale. Samples taken from concrete sidewalks, parking lots, drainage canals, spillways, and a railroad-trestle foundation have construction dates that range from 1923 to 1997. They were analyzed by electron microprobe and by petrographic microscopy. Cracks, air voids, and aggregate alteration were primary locations for investigation and analysis. Using the electron microprobe, ettringite was found in voids of most of the samples, both in good and bad concrete. This leads us to believe that ettringite formation is not causing distress in the concrete. There was one exception in which ettringite was found lining a crack. In this instance, ettringite may have the ability to further the cracking and cause distress. No alkali-silica gel was identified with the microprobe. Using the petrographic microscope in cross-polarized light, a light-brown material was observed that lined some of the air voids and cracks; however, exact mineralogic identifications were not made. Although many instances of chalcedony and other deleterious quartz phases were found, no clear evidence of ASR-gel deterioration was present in our samples using these methods. However, positive identification of the ASR gel was made on an in-place concrete near one of our sample sites and in several sample cores using a newly developed chemical test for the soluble potassium ions associated with the gel. The chemical used in this test is sodium cobaltinitrite, Na3Co(NO2)6.

Jan 1, 1999

By J. M. King

A crucial step in the acquisition by one company of the assets of another, the acquisition of the stock of another company, or the merger of two com-ponies, is the legal due diligence which needs to be performed in order for the acquirer to ascertain or confirm the obligations, liabilities and exposures to risk that are being assumed along with the assets or corporate stock being acquired. Where the obligations, liabilities, or exposures to risk arise from existing contracts, or from pending lawsuits, administrative proceedings, or threats of these actions, those matters are relatively straightforward to discover by careful review of the files of the party whose assets or stock is being acquired. However, where a company is engaged in ongoing mining or processing operations and has operated or owned mining proper-. ties, there are many sources of liability and exposure to risk which could have major adverse economic consequences to the acquiring party and which are not revealed, or at least are not clearly delineated, by the records of the company whose stock or assets are being acquired.

Jan 1, 1990

By R. Zunich, E. Rybinski, M. Grondin, B. Flintoff

It is uncommon these days to read a business magazine or newspaper without finding a reference to Knowledge Management (KM), and its critical importance to corporate success. One definition of KM is: “getting the right knowledge to the right people at the right time and helping them to put information into action in such ways that strive to improve organizational performance.” In the minerals processing industry we could assert that we have been practicing this for years through effective operator training. In most cases we would probably be wrong. Training has certainly filled the need of addressing safety and basic operational issues, but we must collectively focus on education (learning), and the difference, as measured in outcomes, is not at all subtle. This paper briefly examines the history of training and education in the mining industry, and looks in more detail at the impact of one company’s approach to empower its workforce, while keeping the ultimate goal clearly in mind: “The great end of knowledge is not knowledge, but action.” (T.H. Huxley)

Jan 1, 2001

Semisoluble salt minerals are characterized by their ionic bonding and are distinguished from soluble salt minerals by their limited solubility in water. One group of semisoluble salt minerals being considered is the alkaline earth salt minerals, including fluorite (CaF2), calcite (CaCO3) and apatite (Ca5F (PO4)3), as well as celestite (SrSO4) and barite (BaSO4). Another group of semisoluble salt minerals being considered is the rare-earth salts, which include bastnaesite ((Ce, La) CO3F), monazite (CePO4) and xenotime (YPO4). Surface chemistry features of these selected semisoluble salt minerals are discussed with respect to flotation separations. First, the surface chemistry features of alkaline earth semisoluble salt minerals are reviewed, and then the surface chemistry features of rare-earth semisoluble salt minerals are examined. The discussion includes electrokinetic behavior, wetting characteristics and collector adsorption.

By Eduardo M. Sacris

The performance of the grinding circuit, from the initial stages of operation to the present, is discussed. The mill efficiency as measured by the Bond grindability data and the operating work index is presented. The objective has been to produce a sand cyclone overflow containing not more than 6% +65 mesh. However, this has never been attained even at low milling rates. On the other hand, significant improvements in throughput were achieved by instituting some equipment changes and process modifications within the grinding circuit. The latest approach to solving the coarse grind problem is also discussed.

Jan 1, 1983

By D. H. McCain

Through a unique partnership between the Colorado Mine Safety and Training Program (CMSTP), the Colorado Rock Products Association (CRPA) and the Higher Education and Advanced Technology (HEAT) Center, a video packed, dazzling CD-ROM training program was developed for new miners entering the aggregate industry. Why this product was developed, and why the aggregate industry, will be discussed along with the challenges faced throughout the project. Cooperation from every one involved including MSHA made this the product of which all other training materials in the mining industry will be measured against in the 21st Century. This product's versatility and wide application makes it a tool that is as critical to a mine's success as any earth moving machine. Developed with both state and federal grant moneys allows this product to be affordable to small operators and independent contractors. The quality of this two CD-ROM set rivals any commercially made CD-ROM training.

Jan 1, 2001